Simplicity 01532-2 Manuel utilisateur

Marque: Simplicity

Modèle: 01532-2

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

Portable Generator 01532-2

Owner’s Manual

Manuel de l'utilisateur

Manual del Propietario

Model 01532-2

Manual No. 192115GS

Revision 0 (01/07/2003)

Questions? Help is just a moment away!

Vous avez des questions? Vous n'avez pas besoin d'aller loin pour trouver de l'aide!

Preguntas? La ayuda es justa un momento lejos!

Call: Generator Helpline - 1-800-743-4115 M-F 8-5 CT

Appelez: Ligne d'assistance de Générateur - 1-800-743-4115 M-F 8-5 CT

Llamada: Generador Helpline - 1-800-743-4115 M-F 8-5 CT

1000

Starting

Watts

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WISCONSIN, U.S.A.

900W Generator

TABLE OF CONTENTS

Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Know Your Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14

Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Schematic/Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . 17

Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . 18-25

Emmision Control Warranty . . . . . . . . . . . . . . . . . . . . . 26

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

EQUIPMENT

DESCRIPTION

Read this manual carefully and become familiar

with your generator. Know its applications, its

limitations and any hazards involved.

The generators are an engine–driven, revolving field,

alternating current (AC) generator. It was designed to supply

electrical power for operating compatible electrical lighting,

appliances, tools and motor loads. The generator’s revolving

field is driven at about 3,600 rpm by a single-cylinder engine.

CAUTION! DO NOT exceed the generator’s

wattage/amperage capacity. See “Don’t Overload the

Generator” on page 10.

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter or otherwise improve the product and

this document at any time without prior notice.

The Emission Control System for this generator is warranted

for standards set by the Environmental Protection Agency.

SAFETY RULES

This is the safety alert symbol. It is used to

alert you to potential personal injury

hazards. Obey all safety messages that follow

this symbol to avoid possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION, WARNING), a pictorial and/or a

safety message to alert you to hazards. DANGER

indicates a hazard which, if not avoided, will result in death

or serious injury. WARNING indicates a hazard which, if

not avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, might

result in minor or moderate injury. CAUTION, when

used without the alert symbol, indicates a situation that

could result in equipment damage. Follow safety messages

to avoid or reduce the risk of injury or death.

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code).

Other states may have similar laws. Federal laws apply on

federal lands. If you equip the muffler with a spark arrester,

it must be maintained in effective working order.

900W Generator

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• Wear protective goggles, rubber apron, and rubber gloves.

Storage batteries give off explosive hydrogen gas

during recharging.

Hydrogen gas stays around battery for a long

time after battery has been charged.

Slightest spark will ignite hydrogen and cause

explosion.

You can be blinded or severely injured.

Battery electrolyte fluid contains acid and is

extremely caustic.

Contact with battery fluid will cause severe

chemical burns.

DANGER

WHEN ADDING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing gas cap. Loosen cap slowly to relieve pressure in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel

to spill.

• This generator is not for use in mobile equipment or marine

applications.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL

IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

• This generator does not meet U. S. Coast Guard Regulation

33CFR-183 and should not be used on marine applications.

• Failure to use the appropriate U. S. Coast Guard approved

generator could result in bodily injury and/or property damage.

WARNING

• Operate generator ONLY outdoors.

• Keep at least 2 feet of clearance on all sides of generator for

adequate ventilation.

• DO NOT operate generator inside any building or enclosure,

including the generator compartment of a recreational vehicle (RV).

Running generator gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide will cause nausea,

fainting or death.

DANGER

• National Electric Code requires generator to be properly

grounded to an approved earth ground. Call an electrician for

local grounding requirements.

Failure to properly ground generator can result

in electrocution, especially if the generator is

equipped with a wheel kit.

DANGER

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground circuit fault interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

Generator produces powerful voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

DANGER

900W Generator

• DO NOT touch hot surfaces.

• Allow equipment to cool before touching.

Running engines produce heat. Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

WARNING

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

Excessively high operating speeds increase risk of injury

and damage to generator.

Excessively low speeds impose a heavy load.

CAUTION

• See “Don’t Overload Your Generator” on page 10.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected

to it.

CAUTION

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or

contact your nearest authorized service center.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust, dirt,

or corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and disconnect

them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

Unintentional sparking can result in fire or

electric shock.

WARNING

900W Generator

12 Volt DC, 8.3 Amp Accessory Jack — May be used

to power 12 Volt DC electrical devices or recharge 12 Volt

DC batteries.

120 Volt AC, 7.5 Amp Receptacles — May be used to

supply electrical power for the operation of 120 Volt AC,

single phase, 60 Hz electrical lighting, appliance, tool and

motor loads.

Air Cleaner — Uses a foam element to limit the amount

of dirt and dust that enters the engine.

Choke Lever — Used to manually provide proper starting

mixture when engine is cold.

Circuit Breaker (AC) — Receptacles are provided with a

push-to-reset circuit breaker to protect the generator

against electrical overload.

Data Tag — Provides model, revision and serial number

of generator. Please have these readily available if calling for

assistance.

Engine ON/OFF Switch — Used to stop a running

engine.

Fuel Shut-Off Valve — Use this valve to turn the fuel

supply on and off.

Fuel Tank — Capacity of 1.2 U.S. gallons (4.5 liters) of

fuel.

Grounding Lug — Use this connection to properly

ground the generator. See ”Grounding the Generator” on

page 7.

Oil Fill/Drain — Access to oil fill dipstick and engine oil

drain plug.

Recoil Starter — Used for starting the engine.

Spark Plug — Access to engine spark plug.

KNOW YOUR GENERATOR

Read this owner’s manual and safety rules before operating your generator.

Compare the illustrations with your generator to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

120 Volt AC, 7.5 Amp

Receptacle

Recoil Starter

Circuit Breaker (AC)

Oil Fill/Drain

(inside cover)

Choke Lever

Spark Plug (inside

cover)

Fuel Tank

Air Cleaner

Grounding Lug

12 Volt DC, 8.3 Amp

Accessory Jack

Engine ON/OFF Switch

Fuel Shut-Off Valve

Data Tag

900W Generator

ASSEMBLY

Carton Contents

Check all contents. If any parts are missing or damaged, call

the generator helpline at 1-800-743-4115. If calling for

assistance, please have the model, revision, and serial number

from the data tag available. Shipped with your generator is:

• Main unit

• Oil bottle

• Owner’s manual

• Battery charge cables

BEFORE STARTING ENGINE

Add Oil

NOTE: When adding oil to the engine crankcase in the

future, use only high quality detergent oil rated with API

service classification SG, SF/CC, CD. Select the oil’s viscosity

grade according to your expected operating temperature:

SAE 10W-30 is recommended for general all temperature

use. Multi-viscosity oils (10W30, etc.) improve starting in

cold weather, but these oils will result in increased oil

consumption. Check your engine oil level more frequently

to avoid possible damage from running low on oil.

To Add Engine Oil:

• Place the generator on a level surface.

• Remove the oil fill cover.

• Remove oil filler cap and wipe dipstick clean (Figure 1).

• If the oil level is not at the point of overflowing from the

oil filler neck, slowly fill engine with recommended oil.

• Reinstall oil filler cap and tighten securely.

• Replace the oil fill cover.

• Check the engine oil level before starting each time

thereafter.

Add Fuel

WARNING! NEVER fill fuel tank indoors. NEVER

fill fuel tank when engine is running or hot. Allow unit

to cool for two minutes before refueling. DO NOT

light a cigarette or smoke when filling the fuel tank.

WARNING! DO NOT overfill the fuel tank.

Always allow room for fuel expansion.

• Use clean fresh UNLEADED fuel with a pump rating of

86 or higher. DO NOT use premium or leaded fuel. DO

NOT mix oil with fuel.

• Clean area around fuel fill cap, remove cap.

• Check the fuel level.

• If fuel level is low, slowly add recommended fuel to fuel

tank, up to the shoulder of the fuel strainer (Figure 2).

Be careful not to overfill (there should be no fuel in the

filler neck).

NOTE: Occasionally clear the fuel strainer of any dirt,

rust, or other particulate matter.

• Install fuel cap and wipe up any spilled fuel.

Occasionally you may hear a light “spark knock” or

“pinging” (metallic rapping noise) while operating under

heavy loads. This is no cause for concern. If spark knock or

pinging occurs at a steady engine speed under normal load,

change brands of fuel or obtain a higher octane rated fuel.

If pinging or spark knock persists, see your local Briggs &

Stratton repair center.

colder 32°F warmer

SAE 10W30 SAE 30

Oil Filler Neck

Figure 1 — Adding Engine Oil

Fill to This Level

Figure 2 — Fuel Level

900W Generator

GROUNDING THE

GENERATOR

The National Electrical Code requires that the frame and

external electrically conductive parts of this generator be

properly connected to an approved earth ground. Local

electrical codes may also require proper grounding of the

unit. For that purpose, a GROUNDING WING NUT is

provided on the generator housing (Figure 3).

Generally, connecting a No. 12 AWG (American Wire

Gauge) stranded copper wire to the grounding wing nut

and to an earth-driven copper or brass grounding rod

(electrode) provides adequate protection against electrical

shock. Be careful to keep the grounding wire attached after

connecting the stranded copper wire. However, local codes

may vary widely. Consult with a local electrician for

grounding requirements in your area.

Properly grounding the generator helps prevent electrical

shock if a ground fault condition exists in the generator or

in connected electrical devices. Proper grounding also helps

dissipate static electricity, which often builds up in

ungrounded devices.

OPERATING THE

GENERATOR

CAUTION! NEVER start or stop the engine with

electrical loads connected to the unit and with the

connected devices turned ON.

Starting the Engine

Disconnect all electrical loads from the generator. Use the

following start instructions:

• Be sure the spark plug wire is attached to the spark plug.

• Turn the fuel valve to the “Open” position (fully

clockwise) (Figure 4).

• Slide the choke lever to the “Choke” position (all the

way to the right) (Figure 5).

• Place the engine switch in the “On” position (Figure 6).

• Grasp starter grip and slowly pull the rope until you feel

some resistance, then pull the cord out with a rapid full

arm stroke. Let rope return slowly. DO NOT let rope

“snap back” against the unit.

Figure 5 — Choke Lever

Figure 4 — Fuel Valve in Open Position

Figure 6 — Engine Switch in On Position

Figure 3 — Grounding Wing Nut

Grounding Wing Nut

900W Generator

NOTE: If engine starts after 3 pulls, but fails to run for

more than 10 seconds, check for proper oil level in

crankcase. This unit is equipped with a Oil Alert System

(see page 8).

• Slide the choke lever left to the “Run” position as the

engine warms up.

NOTE: Under no load conditions, the engine speed may

vary slightly faster or slower until engine temperatures

stabilize.

CAUTION! Breathing Hazard! NEVER run

engine in enclosed poorly ventilated areas. Engine

exhaust contains carbon monoxide, an odorless and

deadly gas.

Connecting Electrical Loads

• Let engine stabilize and warm up for a few minutes after

starting.

• DO NOT connect 240 Volt loads to 120 Volt receptacles.

• DO NOT connect 3–phase loads to the generator.

• DO NOT connect 50 Hz loads to the generator.

• Plug in and turn on the desired 120 Volt AC, single

phase, 60 Hertz electrical loads.

• DO NOT OVERLOAD THE GENERATOR. Add up

the rated watts (or amps) of all loads to be connected at

one time. This total should not be greater than the rated

wattage/amperage capacity of the generator. See “Don’t

Overload the Generator” on page 10.

Stopping the Engine

• Unplug all electrical loads from the unit. NEVER start or

stop engine with electrical devices plugged in and turned

on.

• Let engine run at no–load for two minutes to stabilize

the internal temperatures.

• Move engine switch to the “Off” position.

• Turn the fuel valve to the “Close” position (fully

counterclockwise).

NOTE: In an emergency, stop the engine by moving the

engine switch to the “Off” position.

Oil Alert System

The Oil Alert System is designed to prevent engine damage

caused by an insufficient amount of oil in the crankcase.

Before the oil level in the crankcase can fall below a safe

limit, the Oil Alert System will automatically shut down the

engine (the engine switch will remain in the “On” position).

If the Oil Alert System shuts down the engine, add engine

oil.

Charging a Battery

WARNING! Storage batteries emit explosive gas

while charging that remains around a battery for a

long time after it has been charged. The slightest

spark can ignite the gas, causing an explosion that

can shatter the battery and cause blindness or

other injury.

WARNING! DO NOT permit smoking, open

flame, sparks or any other source of heat around a

battery. DO NOT use a lighter or other flame for

checking battery fluid levels. Wear protective

goggles, rubber apron and rubber gloves when

working around a battery. Battery electrolyte fluid is

an extremely caustic sulfuric acid solution that can

cause severe burns. DO NOT permit fluid contact

with eyes, skin, clothing, etc. If spill occurs, flush

area with clear water immediately.

Your generator has the capability of recharging a discharged

12 Volt automotive or utility style storage battery. DO

NOT use the unit to charge any 6 Volt batteries. DO NOT

use the unit to crank an engine having a discharged battery.

To recharge 12 Volt batteries, proceed as follows:

• If necessary, clean battery posts or terminals.

• Check fluid level in all battery cells. If necessary, add

ONLY distilled water to cover separators in battery

cells. DO NOT use tap water.

• If the battery is equipped with vent caps, make sure they

are installed and are tight.

• Connect battery charge cable connector plug to the

12 Volt DC panel receptacle.

• Connect battery charge cable clamp with red handle to

battery post or terminal indicated by Positive, POS or

(+) (Figure 7).

900W Generator

• Connect battery charge cable clamp with black handle

to battery post or terminal indicated by Negative,

NEG, or (–) (Figure 7).

• Start generator. Let the engine run while battery

recharges.

• When battery has charged, shut down engine (see

“Stopping The Engine”)

NOTE: Use an automotive hydrometer to test battery

state of charge and condition. Follow the hydrometer

manufacturer’s instructions carefully. Generally, a battery is

considered to be at 100% state of charge when specific

gravity of its fluid (as measured by hydrometer) is 1.260 or

higher.

CONNECTOR PLUGS

120 Volt AC, 15 Amp Receptacle

Each outlet socket is protected against overload by a

7.5 Amp push-to-reset circuit breaker. Use each receptacle

to operate 120 Volt AC, single phase, 60 Hz electrical loads

requiring up to 1,000 watts (1.0 kW) of power (Figure 8).

CAUTION! Although each receptacle is rated

for 120 Volts at 15 Amps (1,440 watts or 1.44 kW),

the generator is rated for a total of 1,000 watts.

Powering loads that exceed the wattage capacity of

the generator can damage it or cause serious

injuries. The total of loads powered through these

receptacles should not exceed 7.5 Amps.

12 Volt DC Accessory Jack

This receptacle allows you to recharge a 12 Volt

automotive or utility style storage battery with the battery

charge cable provided. Camping-style air pumps, lanterns,

fans, or other 12 Volt devices having a cigarette lighter-type

plug may also be powered by this outlet (Figure 9).

This receptacle can not recharge 6 Volt batteries and can

not be used to crank an engine having a discharged battery.

See “Charging a Battery” (page 8) before attempting to

recharge a battery.

EXTENSION CORDS

Use only high quality, well-insulated, extension cords with

the generator’s 120 Volt electrical receptacles.

Check the ratings of all extension cords before you use

them. Such cords should be rated for 125 Volt AC loads at

15 Amps (or greater) for most electrical devices. Some

devices, however, may not require this type of extension

cord. Check the owner’s manuals of those devices for their

recommendations.

Keep extension cords as short as possible, preferably less

than 15 feet long, to prevent voltage drop and possible

overheating of wires.

Figure 8 — 120 Volt AC, 15 Amp Duplex Receptacle

Figure 9 — 12 Volt DC Accessory Jack

Red Lead

To 12 Volt DC Panel

Receptacle

Positive

Negative

Figure 7 — Battery Connections

900W Generator

DON'T OVERLOAD YOUR

GENERATOR

Capacity

You must make sure your generator can supply enough

rated (running) and surge (starting) watts for the items you

will power at the same time. Follow these simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items. This is

the amount of power your generator must produce to

keep your items running. See Figure 10.

3. Estimate how many surge (starting) watts you will

need. Surge wattage is the short burst of power

needed to start electric motor-driven tools or

appliances such as a circular saw or refrigerator.

Because not all motors start at the same time, total

surge watts can be estimated by adding only the

item(s) with the highest additional surge watts to the

total rated watts from step 2.

Example:

Total Rated (Running) Watts = 3075

Highest Additional Surge Watts = 1800

Total Generator Output Required = 4875

Power Management

To prolong the life of your generator and attached devices,

it is important to take care when adding electrical loads to

your generator. There should be nothing connected to the

generator outlets before starting it's engine. The correct

and safe way to manage generator power is to sequentially

add loads as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly.

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity,

as described above.

*Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Tool or Appliance

Rated (Running)

Watts

Additional Surge

(Starting) Watts

Window Air

Conditioner

1200 1800

Refrigerator 800 1600

Deep Freezer 500 500

Television 500 -

Light (75 Watts) 75 -

3075 Total

Running Watts

1800 Highest

Surge Watts

Tool or Appliance

Rated*

(Running)

Watts

Additional

Surge

(Starting)

Watts

Essentials

Light Bulb - 75 watt

Deep Freezer

500

Sump Pump

800

1200

Refrigerator/Freezer - 18 Cu. Ft.

800

1600

Water Well Pump - 1/3 HP

1000

2000

Heating/Cooling

Window AC - 10,000 BTU

1200

1800

Window Fan

300

600

Furnace Fan Blower - 1/2 HP

800

1300

Kitchen

Microwave Oven - 1000 Watt

1000

Coffee Maker

1500

Electric Stove - Single Element

1500

Hot Plate

2500

Family Room

DVD/CD Player

100

VCR

100

Stereo Receiver

450

Color Television - 27”

500

Personal Computer w/17” monitor

800

Other

Security System

180

AM/FM Clock Radio

300

Garage Door Opener - 1/2 HP

480

520

Electric Water Heater - 40 Gallon

4000

DIY/Job Site

Quartz Halogen Work Light

1000

Airless Sprayer - 1/3 HP

600

1200

Reciprocating Saw

960

Electric Drill - 1/2 HP

1000

Circular Saw - 7 1/4”

1500

Miter Saw - 10”

1800

Table Planer - 6”

1800

Table Saw/Radial Arm Saw - 10”

2000

Air Compressor - 1-1/2 HP

2500

Figure 10 - Wattage Reference Chart

900W Generator

PRODUCT

SPECIFICATIONS

Generator Specifications

Rated Surge Watts . . . . . . . . . . . . . . . 1,000 Watts

Rated Running Watts . . . . . . . . . . . . . 900 Watts

Rated Maximum Current

At 120 Volts AC . . . . . . . . . . . . . .7.5 Amps

At 12 Volts DC . . . . . . . . . . . . . . .8.3 Amps

Phase . . . . . . . . . . . . . . . . . . . . . . . .Single Phase

Rated Frequency . . . . . . . . . . . . . . . .60 Hertz

Packaged Weight . . . . . . . . . . . . . . . .61 lbs.

Engine Specifications

Model

. . . . . . . . . . . . . . . . . . . . . . . .

Mitsubishi GM82

Rated Horsepower . . . . . . . . . . . . . . 2.4 at 4000 rpm

Displacement . . . . . . . . . . . . . . . . . . . 80cc

Spark Plug Type: . . . . . . . . . . . . . . . . . NGK BP6HS or

equivalent

Set Gap To: . . . . . . . . . . . . . . . . . . . . . 0.030inch (0.75mm)

Fuel Capacity . . . . . . . . . . . . . . . . . . . 1.2 U.S. gallons (4.5 l)

GENERAL MAINTENANCE

RECOMMENDATIONS

The generator warranty does not cover items that have

been subjected to operator abuse or negligence. To receive

full value from the warranty, operator must maintain

generator as instructed in this manual.

Some adjustments will need to be made periodically to

properly maintain your generator.

All adjustments in this section should be made at least

once each season. Follow the requirements in the

“Maintenance Schedule” chart shown below in Figure 11.

NOTE: Once a year you should clean or replace the spark

plug and replace the air filter. A new spark plug and clean

air filter assure proper fuel-air mixture and help your

engine run better and last longer.

GENERATOR

MAINTENANCE

Generator maintenance consists of keeping the unit clean

and dry. Operate and store the unit in a clean dry

environment where it will not be exposed to excessive

dust, dirt, moisture or any corrosive vapors. Cooling air

slots in the generator must not become clogged with snow,

leaves or any other foreign material.

1 Clean more often under dirty or dusty conditions. Replace cleaner parts if very dirty.

2 Check every 10 hours or 3 months.

3 These items should be serviced by an authorized dealer, unless the owner has the proper tools and is mechanically

proficient.

Item

Operation

Each use

First Month or

25 hours

Every 3 months

or 50 hours

Every 6 months

or 100 hours

Engine oil

Check level

Change

Air cleaner

Check

Clean

X (1)

Spark arrester

Check – Clean

X (2,3)

Spark plug

Check – Clean

Valve clearance

Check – Adjust

X (3)

Fuel tank strainer

Clean

X (3)

Fuel line

Check (Replace if

necessary)

Every 3 years (3)

Figure 11 – Maintenance Schedule

900W Generator

Check the cleanliness of the generator frequently and clean

when dust, dirt, oil, moisture or other foreign substances

are visible on its exterior surface.

NOTE: DO NOT use a garden hose to clean generator.

Water can enter engine fuel system and cause problems. In

addition, if water enters generator through cooling air

slots, some of the water will be retained in voids and

cracks of the rotor and stator winding insulation. Water

and dirt buildup on the generator internal windings will

eventually decrease the insulation resistance of these

windings.

To Clean the Generator

• Use a damp cloth to wipe exterior surfaces clean.

• Soft, bristle brush may be used to loosen caked on dirt

or oil.

CAUTION! NEVER insert any object or tool

through the air cooling slots, even if the engine is

not running.

• A vacuum cleaner may be used to pick up loose dirt and

debris.

• Low pressure air (not to exceed 25 psi) may be used to

blow away dirt. Inspect cooling air slots and opening on

generator. These openings must be kept clean and

unobstructed.

WARNING! When working on the generator

always disconnect spark plug wire from spark plug

and keep it away from spark plug.

ENGINE MAINTENANCE

Checking Oil Level

Oil level should be checked prior to each use or at least

every 5 hours of operation. Keep oil level maintained.

Changing Engine Oil

Change the oil after the first month of operation, then

every 25 hours. If you are using your generator under

extremely dirty or dusty conditions, or in extremely hot

weather, change the oil more often.

Change the oil while the engine is still warm from running,

as follows:

• Remove the oil fill cover and clean area around oil drain

plug (Figure 12).

• Remove oil drain plug, sealing washer, and oil filler cap.

Drain oil completely into a suitable container.

• Install oil drain plug and sealing washer. Tighten securely.

• Refill with recommended oil and check the level. See

page 6 for oil recommendations.

• Wipe up any spilled oil.

CAUTION! Avoid prolonged or repeated skin

contact with used motor oil. Used motor oil has

been shown to cause skin cancer in certain

laboratory animals. Thoroughly wash exposed areas

with soap and water. KEEP OUT OF REACH OF

CHILDREN.

DON'T POLLUTE. CONSERVE RESOURCES.

RETURN USED OIL TO COLLECTION CENTERS.

• Replace oil fill cover.

Clean/Replace Spark Plug

Check and clean the spark plug every 50 hours of

operation or every three months, whichever comes first.

This will help your engine to start easier and run better.

• Remove spark plug access cover. Remove spark plug cap.

• Clean the area around the spark plug.

• Remove and inspect the spark plug.

• Replace the spark plug if electrodes are pitted or burned

or the porcelain is cracked. Use recommended plug for

replacement.

• Check electrode gap with wire feeler gauge and set spark

plug gap between 0.028 and 0.031 inch (0.7 to 0.8 mm) if

necessary (Figure 13).

Figure 12 — Oil Drain Plug

Oil Drain Plug

900W Generator

• Reinstall spark plug.

Service Air Cleaner

Your engine will not run properly and may be damaged if

you run it using a dirty air filter element.

Check the air filter every use and clean or replace the

paper air filter element every 50 hours of operation or

every three months, whichever comes first. Clean or

replace more often if operating under dusty or dirty

conditions.

To clean or replace air filter element:

• Loosen the air cleaner cover screws, remove the air

cleaner cover, and remove the element (see item

number 4, exploded view on page 22.

• Wipe clean the inside of the filter housing and cover

thoroughly.

• Wash the element in a solution of household detergent

and warm water, then rinse thoroughly. Or wash in

nonflammable or high flash point solvent. Allow the

element to dry thoroughly.

• Soak the element in clean engine oil and squeeze out the

excess oil. DO NOT twist. The engine will smoke during

initial start-up if too much oil is left in the element.

NOTE: If you need to order a new air filter element,

please call 1-800-743-4115.

• Reinstall the air cleaner element and the cover. Hand

tighten the air cleaner cover screws.

Clean Spark Arrester Screen

The engine muffler is equipped with a removable spark

arrester screen. Inspect and clean the screen every

10 hours of operation or every three months, as shown in

Figure 14:

• Loosen the screw on the muffler tail pipe and remove

the spark arrester screen.

• Use a brass or stiff-bristle brush to remove carbon

deposits from the spark arrester surface.

• Inspect the spark arrester for breaks or tears and

replace it if necessary.

NOTE: If you need to order a new spark arrester, please

call 1-800-743-4115.

• Install the clean screen in the reverse order of removal.

NOTE: If you use your generator on any forest-covered,

brush-covered or grass-covered unimproved land, it must

have a spark arrester installed. The spark arrester must be

maintained in good condition by the owner/operator.

STORAGE INSTRUCTIONS

Transporting and Storage

When transporting the generator, turn the engine switch

to “Off” and the fuel valve to “Close”. Keep the generator

level to prevent fuel spillage.

WARNING! Contact with a hot engine or

exhaust system can cause serious burns or fires. Let

the engine cool before transporting or storing the

generator.

Take care to not drop or strike the generator when

transporting. DO NOT place heavy objects on the

generator.

The generator should be started at least once every seven

days and allowed to run at least 30 minutes. If this cannot

be done and you must store the unit for more than 30 days,

use the following guidelines to prepare it for storage.

Figure 13 — Service Spark Plug

Spark Arrester

Screen

Muffler Tail Pipe

Spark Arrester

Attachment Screw

Figure 14 – Service Spark Arrester Screen

900W Generator

Long Term Storage Instructions

WARNING! NEVER store engine with fuel in

tank indoors or in enclosed, poorly ventilated areas

where fumes may reach an open flame, spark or

pilot light as on a furnace, water heater, clothes

dryer or other gas appliance.

Be sure the storage area is free from excessive

humidity and dust.

One Month to One Year

Drain the carburetor float bowl (see following section) and

fuel tank into a suitable container. After removal from

storage, fill with fresh fuel before starting.

More than One Year

It is important to prevent gum deposits from forming in

essential fuel system parts such as the carburetor, fuel filter,

fuel hose or tank during storage. Also, experience indicates

that alcohol-blended fuels (called gasohol, ethanol or

methanol) can attract moisture, which leads to separation

and formation of acids during storage. Acidic gas can

damage the fuel system of an engine while in storage.

To avoid engine problems, the fuel system should be

emptied before storage of 30 days or longer. Follow these

instructions:

Protect Fuel System

WARNING! Drain fuel into approved container

outdoors, away from open flame. Be sure engine is

cool. DO NOT smoke.

• Drain carburetor float bowl and fuel tank into a suitable

container by loosening the drain screw (Figure 15).

• Retighten drain screw before refueling.

Change Oil

While engine is still warm, change oil as described on

page 12. Refill with recommended grade.

Oil Cylinder Bore

• Remove spark plug and pour about one tablespoon of

clean engine oil into the cylinder.

CAUTION! Avoid spray from spark plug hole

when cranking engine slowly.

• Cover spark plug hole with rag. Crank slowly several

times to distribute oil.

• Install spark plug. DO NOT connect spark plug wire.

• Slowly pull the starter grip until resistance is felt. At this

point, the piston is coming up on its compression stroke

and both the intake and exhaust valves are closed.

Storing the engine in this position will help to protect it

from internal corrosion.

Generator

• Clean the generator as outlined on page 12 (“To Clean

the Generator”).

• Check that cooling air slots and openings on generator

are open and unobstructed.

Other Storage Tips

• DO NOT store fuel from one season to another.

• Replace the fuel can if it starts to rust. Rust and/or dirt

in fuel will cause problems.

• If possible, store your unit indoors. BE SURE TO

EMPTY THE FUEL TANK.

• Cover your unit with a suitable protective cover that

does not retain moisture.

IMPORTANT: NEVER cover your generator while engine

and exhaust area are warm.

• Store generator in clean, dry area.

Carburetor Fuel

Drain Screw

Access Hole

Figure 15 – Drain Fuel From Carburetor

900W Generator

NOTES

900W Generator

TROUBLESHOOTING

Problem

Cause

Correction

No AC or DC output

is available but

engine is running.

1. One of the circuit breakers is open.

2. Fault in generator.

3. Poor connection or defective cord set.

4. Connected device is bad.

1. Reset circuit breaker.

2. Contact Briggs & Stratton Power

Products service facility.

3. Check and repair.

4. Connect another device that is in

good condition.

Generator runs good

at no-load but

“bogs down" when

loads are

connected.

1. Short circuit in a connected load.

2. Engine speed is too slow.

3. Generator is overloaded.

4. Shorted generator circuit.

1. Disconnect shorted electrical load.

2. Contact Briggs & Stratton service

facility.

3. See “Don't Overload the Generator”

on page 10.

4. Contact Briggs & Stratton Power

Products service facility.

Engine will not start;

or starts and runs

rough.

1. Engine switch set to “Off”.

2. Fuel valve in the “Closed” position.

3. Dirty air cleaner.

4. Out of gasoline.

5. Stale gasoline.

6. Spark plug wire not connected to spark

plug.

7. Bad spark plug.

8. Water in gasoline.

9. Overchoked or flooded.

10. Excessively rich fuel mixture.

11. Intake valve stuck open or closed.

12. Engine has lost compression.

1. Set switch to “On”.

2. Turn fuel valve to the “Open”

position.

3. Clean or replace air cleaner.

4. Fill fuel tank.

5. Drain gas tank and carburetor; fill

with fresh fuel.

6. Connect wire to spark plug.

7. Replace spark plug.

8. Drain gas tank and carburetor; fill

with fresh fuel.

9. Wait 5 minutes and re-crank engine.

10. Contact Briggs & Stratton service

facility.

11. Contact Briggs & Stratton service

facility.

12. Contact Briggs & Stratton service

facility.

Engine shuts down

when running.

1. Out of gasoline.

2. Low oil level.

1. Fill fuel tank.

2. Fill cranckcase to proper level.

Engine lacks power.

1. Load is too high.

2. Dirty air filter.

1. See “Don't Overload the Generator”

on page 10.

2. Replace air filter.

Engine “hunts” or

falters.

1. Choke is opened to soon.

2. Carburetor is running too rich or too lean.

1. Move choke to halfway position until

engine runs smoothly.

2. Contact Briggs & Stratton service

facility.

900W Generator

WIRING DIAGRAM

900W Generator

EXPLODED VIEW AND PARTS LIST – MAIN UNIT

Item Part # Qty Description

1 NSP 1 ENG, MITSUB, 2.4HP

2 187378GS 1 ROTOR

3 187411GS 1 BRG

4 187379GS 1 STATOR

5 187430GS 1 LEAD, GREEN

6 187409GS 1 BUSHING, LEAD WIRE, G790B

7 187381GS 1 RBC, 1K

8 187399GS 3 SCREW, SELF TAP, M6-12

9 187382SGS 1 FAN, COOLING

10 187388GS 1 BOLT, RTR

11 187389GS 3 BOLT, STATOR

12 187405GS 1 INSLTN, HEAT SEALED, #1

13 187384GS 1 MFFLR, SEALED

14 187407GS 1 INSLTN, HEAT SEALED, #2

15 187403GS 1 DUCT, AIR

Item Part # Qty Description

16 187392GS 2 PHMS, M6-1.0, W/L/FW

17 187383GS 1 BASE, GEN

18 187390GS 4 BOLT, FLNG, M6-1.0 X 10

19 187385GS 4 MNT, VIBR

20 187427GS 4 HHCS, FLNG, M8-1.25 X 12

21 187424GS 1 NUT, WING, M5 X 0.8

22 187423GS 1 NUT, M5 X 0.8

23 187419GS 2 WSHR, LOCK

24 187420GS 2 WSHR, FLAT

25 187401GS 2 NUT, M8-1.25, FLANGE

26 187415GS 1 PHMS, M5-0.8 X 20

27 187413GS 2 CNNCTR

28 187434GS 4 HHCS, FLNG

29 187431GS 1 STND, ENG

900W Generator

Item Part # Qty Description

1 187436GS 1 CAP, FUEL

2 187439GS 1 PACKING, TANK

3 187438GS 1 FLTR, FUEL

4 187769GS 3 U-PACKING

5 187437GS 1 TANK, FUEL, 4.5L

6 187766GS 1 DECAL, CHOKE

7 187756GS 4 BOLT, COVER (M5-16)

8 187875GS 1 HSG, GEN, MFFLR

10 187772GS 1 COVER, SPARK PLUG

11 187757GS 5 BOLT, COVER (M6-16)

12 187760GS 11 PHMS, M4-12 W/FW

13 187435GS 1 CVR, MFFLR, GEN

14 187775GS 3 BOLT, MFFLR CVR (M6-16)

15 191436GS 1 DECAL CAUTION HOT

16 187774GS 4 BOLT, COVER (M6-20)

17 187761GS 8 NUT, M4X0.6 W/FW

18 187463GS 1 INSLTN, MFFLR

19 187874GS 1 HSG, GEN

20 NSP 1 DECAL, EMISSIONS

21 187457GS 1 CONDENSER, 300V

22 191528GS 1 DECAL, WARNING

23 187759GS 2 BOLT, COVER (M5-10)

24 187462GS 1 DIODE, BRIDGE

Item Part # Qty Description

25 187371AGS 1 BOTTLE, OIL

26 192284GS 1 DECAL, LWR PANEL

27 187773GS 1 COVER, OIL FILL

28 187460GS 1 CB, DC

29 187454GS 1 CB, 8A, 125V

30 187873GS 1 OUTLET, ACCESSORY DC

31 187450GS 1 SWITCH, ENG, ON/OFF

32 187812GS 1 CPNL

33 187456GS 1 RECPTCL, 15A, 125V

34 187763GS 1 DECAL, CAUTION OIL

35 187876GS 1 CABLE, BATTERY CHARGE

36 192283GS 1 DECAL, UNIT

37 191545GS 1 DECAL, FUEL SHUTOFF

38 187447GS 1 INSLTN, HTSHLD, TANK #1

39 187448GS 1 INSLTN, HTSHLD, TANK #2

40 187442GS 2 BRKT, TANK, FUEL

41 187758GS 1 BRKT, FUEL COCK

42 187443GS 1 COCK, FUEL

43 187770GS 1 PHMS, M5-10 W/FW

44 187579GS 1 CLIP, FUEL HOSE

45 187440GS 1 FLTR, FUEL

46 187578GS 1 HOSE, FUEL

EXPLODED VIEW AND PARTS LIST – MAIN UNIT

900W Generator

EXPLODED VIEW AND PARTS LIST – ENGINE

Cylinder Block, Cylinder Head

Item Part # Qty Description

1 187404GS 1 ASSY, CYL HEAD

2 187406GS 2 TPPT, CYL HEAD

3 187408GS 2 VLV, EXH

4 187410GS 2 SPRNG, VLV

5 187412GS 2 RTNR, VLV SPG

6 187414GS 2 ROD, PUSH

7 187416GS 1 ASSY, RCKR, ARM

8 187417GS 2 NUT, CYL HEAD

9 187418GS 2 SCRW, ADJST

10 187421GS 1 PLT, CYL HEAD

Item Part # Qty Description

11 187422GS 1 SEAL, VLV STEM

12 187423GS 4 NUT, M5 X 0.8

13 187426GS 4 BOLT, FLNG

14 187428GS 2 PIN, DWL

15 187429GS 1 GSKT, HEAD

16 187468GS 1 CVR, VALVE

17 187470GS 4 BOLT, VALVE CVR

18 187472GS 1 GSKT, VALVE CVR

19 187569GS 2 BOLT, STUD

Item Part # Qty Description

1 187380GS 1 BLOCK, CYL

2 187386GS 1 ASSY, GOV, GEAR

3 187387GS 1 SLIDER, GOV

4 187391GS 1 SHFT, GOV

5 187393GS 2 PLUG, DRAIN

6 187394GS 2 SEAL, OIL

7 187395GS 1 BRG, BALL

8 187400GS 1 WSHR, CYLBLOCK

9 187402GS 2 GSKT, CYLBLOCK

La page charge ...

Simplicity 01532-2 Manuel utilisateur

Marque: Simplicity

Modèle: 01532-2

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

Portable Generator 01532-2

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 01532-2 User manual
español: Simplicity 01532-2 Manual de usuario

Simplicity 01532-2 Manuel utilisateur

Ce manuel convient également à

Simplicity 01532-2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents