Chief PAC400 Guide d'installation
- Catégorie
- Supports muraux à panneau plat
- Taper
- Guide d'installation
PAC-400 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, Inc., and its affiliated corporations
and subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components does not exceed the maximum weight
capacity of the mount to which this accessory is being
installed.
DIMENSIONS
16.71
424.414
16.71
424.414
8.48
215.382
8.35
212.207
PIVOT +/- 90
1.18
29.968
Installation Instructions PAC-400
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
PAC-400 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
1/8" (included)
5/32" (included)
A (1)
B (2) C (4)
D (4) E (4)
[rotation assembly]
[latching flag] [mounting button]
[#10-24 x 3/8"]
(security) [#10-24 x 1/4"]
F(1)
5/32
(secuiy)
Installation Instructions PAC-400
5
Assembly And Installation
1. Remove screen from Chief mount or , if not installed, install
PSB interface bracket to back of screen per instructions
supplied with mount.
2. Attach mounting buttons to rotation assembly, making sure
the buttons are securely fastened. (See Figure 2)
Figure 1
3. Attach to PSB interface bracket by placing the mouting
buttons of PSB into the teardrop slots of PAC-400. Make
sure the mounting buttons are placed securely in teardrop
slots. (See Figure 2)
Figure 2
4. Place latching flags over buttons and secure using a 10-24
Phillips head cap screws.
NOTE: Use 10-24 x 1/4" Phillips security screws (D) and
security hex key instead of Phillips screws for added
security. (See Figure 3)
(C) x 4
(A)
2
PSB(example)
PSB mounting button
teardrop slot of PAC-400
PAC-400 Installation Instructions
6
Figure 3
5. Set desired amount of friction for rotating screen by
tightening or loosening nuts on back side of PAC-400. (See
Figure 4)
Figure 4
6. With the aid of another person, lift display and PAC-400 up
to mount, aligning buttons of rotation accessory with slots in
the Chief mount.
7. Raise safety latch on Chief mount to secure display, making
sure latch is completely engaged.
8. To rotate screen the other way, take screen and rotation
accessory from Chief mount and rotate the back plate of the
PAC-400 by 90 degrees.
9. Install screen on Chief mount.
Cable Management (Optional)
1. Use holes on outside bends to tie wires for cable
management. (See Figure 5)
Figure 5
NOTE: On tilting mounts, it may be necessary to increase
friction on tilting mechanism since PAC-400 adds depth
to overall installation and roll adjustment on PDS mount
may need tightening.
4
(B) x 2
(E) x 4
(F) x 4
or
4
or
5
cable (typical)
cable ties (not included)
Installation Instructions PAC-400
7
PAC-400 Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8809-000012 Rev 02
2010 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
08/10
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief PAC400 Guide d'installation
- Catégorie
- Supports muraux à panneau plat
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief PAC400 Installation guide
Documents connexes
-
Chief PAC252 Guide d'installation
-
-
-
-
Chief PACCS1 Guide d'installation
-
-
-
-