Chief CMA345 Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
CMA345 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the CMA mount does not exceed
500 lbs (226.8 kg).
NOTE: The weight capacity of the CMA mounts may be
LIMITED to the lowest weight capacity of any other
component located between the ceiling plate and the
projector/display.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! : These CMA mounts are designed to be:
• mounted to a 2" x 6" wood framework ceiling;
• mounted to a 8" concrete ceiling with a drywall
covering of a maximum of 5/8";
• mounted to a suspended metal framing channel
ceiling.
WARNING: Do NOT attach to vertical mounting surfaces
such as walls or angled ceilings!
--SAVE THESE INSTRUCTIONS--
Installation Instructions CMA345
3
DIMENSIONS
TOOLS REQUIRED FOR INSTALLATION
PARTS
2.99
76.0
0.38
9.7
ACCEPTS 1.5" NPT THREADS
5/32" (included) 1/4"
A (1)
[CMA345]
B (1)
5/16-18 X 3/8"
C (1)
5/32"
CMA345 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions CMA345
5
INSTALLATION AND ASSEMBLY
These CMA mounts are designed for attachment to a 2" x 6"
wood framework ceiling, a concrete ceiling or a suspended
metal framing channel ceiling, and provides vertical
adjustments in 3/4" increments.
WARNING: Do NOT attach to vertical mounting surfaces
such as walls or angled ceilings!
WARNING: IMPROPER INSTALLATION CAN LEAD TO
LIFT FALLING CAUSING SEVERE PERSONAL INJURY OR
DAMAGE TO EQUIPMENT! It is the installer’s responsibility
to make certain the structure to which the mount is being
attached is capable of supporting five times the weight of the
CMA mount and all attached equipment. Reinforce the
structure as required before installing the mount.
NOTE: The following instructions assume a suitable mounting
structure and surface exists prior to installation.
Installing to a Wood Framework (Joists)
1. Using CMA345 as a template, mark and drill 1/4" pilot holes
at desired mounting location. Make sure holes are centered
on wood studs.
IMPORTANT ! : If using only two bolt holes for mounting,
either two middle opposing holes (scenario 1) or two
diagonally opposing holes (scenarios 2 and 3) must be
used. See Figure 1 for the ONLY acceptable two-bolt
mounting scenarios.
Figure 1
2. Use 3/8" x 2-1/2" (minimum) Grade 2 lag screws (not
provided) to secure CMA mount to the joists or wood
framework, using the bolt holes noted. (See Figure 2)
Figure 2
Installing to a Suspended Ceiling
NOTE:
The CMA mount may be suspended from four 3/8 in.
diameter ASTM A307 or better threaded rods (not
provided) which are secured to a 1-5/8" x 1-5/8" 12ga
metal framing strut channel (spanning a maximum of 4
feet--not provided) by ASTM A307 or better 3/8"
channel nuts (not provided). Threaded rods must have
16 threads per square inch.
1. Insert the rods into the four bolt holes in the CMA mount.
(See Figure 2)
2. Secure the threaded rods to the CMA mount with ASTM
A307 or better 3/8" jam nuts (not provided) and washers
(one of each on inside and one of each on outside-not
provided).
Installing to a Solid Concrete Ceiling Structure
WARNING: The CMA345 is designed to be mounted to a
concrete ceiling with a minimum thickness of 8" and a
maximum drywall covering of 5/8".
WARNING: Fischer Ux10 anchors (not provided) must be
installed into structurally sound solid concrete. Installation
into hollow concrete block, mortar, or concrete that exhibits
cracking, spalling, or other defects may result in failure of
anchor and serious personal injury or damage to equipment.
1. Use four Ux10 anchors (not provided) to secure CMA mount
into solid concrete ceiling. (See Figure 2)
2. Place CMA mount over anchors, aligning bolt holes in CMA
mount with installed anchors.
3. Secure CMA mount to ceiling using four 3/8" Grade 2 flat
washers (not provided) and four 3/8" x 2-1/2" Grade 2 bolts
(not provided) tightened over anchors.
1
1
2
2
3
3
0.38
9.7
CMA345 Installation Instructions
6
Attaching Column to CMA345
1. Install 1-1/2" NPT or NPSM following ANSI/ASME B1.20.1
(Schedule 40, 0.154" minimum thickness aluminum - ASTM
B221) threaded extension column (not included) into
threaded collar until tight, with a minimum of four threads
engaged. (See Figure 3)
2. Install 5/16-18 x 3/8" set screw (B) into hole on ceiling plate
(A) to secure pipe to mount. (See Figure 3)
Figure 3
3. Install the ceiling mount and projector to the column using
installation instructions included with the ceiling mount.
(B)
1 1/2 NPT threaded
2
1
(A)
column (not included)
Installation Instructions CMA345
7
CMA345 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8803-000019 Rev03
2013 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
01/13
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief CMA345 Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief CMA345 Installation guide