VTech CTM-S2412 Mode d'emploi
- Catégorie
- Téléphones
- Taper
- Mode d'emploi
SIP Contemporary Series
CTM-S2412
SIP Contemporary Cordless 1-line Hotel Phone
CTM-S2415HC
Virtual Bundle of CTM-C4402 and C4012
SIP Contemporary Cordless 1-line Accessory Handset and Cordless
charging stand
CTM-C4402
SIP Contemporary Cordless 1-line Accessory Handset
C4012
Cordless charging stand
User‘s Guide
EN - 2
1. This product should be installed by a qualified
technician.
2. This product should only be connected to
the host equipment and never directly to
the network such as Public Switch Telephone
Network (PSTN) or Plain Old Telephone
Services (POTS).
3. Read and understand all instructions.
4. Follow all warnings and instructions marked
on the product.
5. Unplug this product from the wall outlet
before cleaning. Do not use liquid or aerosol
cleaners. Use a damp cloth for cleaning.
6. Do not use this product near water such as
near a bath tub, wash bowl, kitchen sink,
laundry tub or swimming pool, or in a wet
basement or shower.
7. Do not place this product on an unstable
table, shelf, stand or other unstable surfaces.
8. Slots and openings in the back or bottom
of the telephone base and handset are
provided for ventilation. To protect them
from overheating, these openings must
not be blocked by placing the product on
a soft surface such as a bed, sofa or rug.
This product should never be placed near or
over a radiator or heat register. This product
should not be placed in any area where
proper ventilation is not provided.
9. This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the type
of power supply on the premises, consult
your dealer or local power company.
10. Do not allow anything to rest on the power
cord. Do not install this product where the
cord may be walked on.
11. Never push objects of any kind into this
product through the slots in the telephone
base or handset because they may touch
dangerous voltage points or create a short
circuit. Never spill liquid of any kind on the
product.
12. To reduce the risk of electric shock, do not
disassemble this product, but take it to
an authorized service facility. Opening or
removing parts of the telephone base or
handset other than specified access doors
may expose you to dangerous voltages
or other risks. Incorrect reassembling can
cause electric shock when the product is
subsequently used.
13. Do not overload wall outlets and extension
cords.
14. Unplug this product from the wall outlet
and refer servicing to an authorized service
facility under the following conditions:
• When the power supply cord or plug is
damaged or frayed.
• If liquid has been spilled onto the product.
• If the product has been exposed to rain
or water.
• If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are covered
by the operation instructions. Improper
adjustment of other controls may result
in damage and often requires extensive
work by an authorized technician to
restore the product to normal operation.
• If the product has been dropped and
the telephone base and/or handset has
been damaged.
• If the product exhibits a distinct change in
performance.
Important safety instructions
The applied nameplate is located at the bottom or rear of the product.
When using your telephone equipment, basic safety precautions should always be followed to reduce the
risk of fire, electric shock and injury, including the following:
EN - 3
English
15. Avoid using a telephone (other than cordless)
during an electrical storm. There is a remote
risk of electric shock from lightning.
16. Do not use the telephone to report a gas
leak in the vicinity of the leak. Under certain
circumstances, a spark may be created
when the adapter is plugged into the power
outlet, or when the handset is replaced in its
cradle. This is a common event associated
with the closing of any electrical circuit. The
user should not plug the phone into a power
outlet, and should not put a charged handset
into the cradle, if the phone is located in
an environment containing concentrations
of flammable or flame-supporting gases,
unless there is adequate ventilation. A spark
in such an environment could create a fire or
explosion. Such environments might include:
medical use of oxygen without adequate
ventilation; industrial gases (cleaning
solvents; gasoline vapors; etc.); a leak of
natural gas; etc.
17. Only put the handset of your telephone next
to your ear when it is in normal talk mode.
18. The power adapters are intended to be
correctly oriented in a vertical or floor mount
position. The prongs are not designed to
hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
19. Use only the power cord and batteries
indicated in this manual. Do not dispose of
batteries in a fire. They may explode. Check
with local codes for possible special disposal
instructions.
20. In wall mounting position, make sure to
mount the telephone base on the wall by
aligning the eyelets with the mounting studs
of the wall plate. Then slide the telephone
base down on both mounting studs until it
locks into place. Refer to the full instructions
in Installation in the user’s manual.
21. This product should be mounted at a height
of less than 2 meters.
22. Listed PoE (The product is considered not
likely to require connection to an Ethernet
network with outside plant routing).
CAUTIONS
• Keep small metallic objects such as pins and
staples away from the handset receiver.
• There may be a risk of explosion if a wrong
type of handset battery is used (CTM-S2412,
CTM-C4402). Use only the supplied
rechargeable battery (BT164392/BT264392)
or replacement battery (BT264392). Dispose
of used batteries according to the information
in The RBRC® seal in this user guide.
SAVE THESE INSTRUCTIONS
EN - 4
1. Ce produit doit être installé par un technicien
qualifié.
2. Ce produit ne doit être connecté qu'à
l'équipement hôte et jamais directement au
réseau tel que le réseau téléphonique public
commuté (RTPC) ou les services téléphoniques
classiques (POTS).
3. Lire et comprendre toutes les instructions.
4. Respecter tous les avertissements et
instructions figurant sur le produit.
5. Débranchez ce produit de la prise murale
avant de le nettoyer. N'utilisez pas de
nettoyants liquides ou en aérosol. Utilisez un
chiffon humide pour le nettoyage.
6. N'utilisez pas ce produit près de l'eau, par
exemple près d'une baignoire, d'une cuvette
de lavage, d'un évier de cuisine, d'une cuve
de lavage ou d'une piscine, ou dans un sous-
sol ou une douche humide.
7. Ne pas placer ce produit sur une table, une
étagère, un support ou toute autre surface
instable.
8. Des fentes et des ouvertures à l'arrière ou en-
dessous du socle du téléphone et du combiné
sont prévues pour la ventilation. Afin de les
protéger contre la surchauffe, ces ouvertures
ne doivent pas être obstruées en plaçant
le produit sur une surface souple comme un
lit, un divan ou un tapis. Ce produit ne doit
jamais être placé à proximité ou au-dessus
d'un radiateur ou d'un registre de chaleur. Ce
produit ne doit pas être placé dans un endroit
où une ventilation adéquate n'est pas assurée.
9. Ce produit ne doit être utilisé qu'avec le type
de source d'énergie indiqué sur l'étiquette
de marquage. Si vous n'êtes pas sûr du
type d'alimentation électrique sur place,
consultez votre revendeur ou votre compagnie
d'électricité locale.
10. Ne laissez rien reposer sur le cordon
d'alimentation. N'installez pas ce produit à un
endroit où l'on pourrait marcher sur le cordon.
11. N'introduisez jamais d'objets de quelque
nature que ce soit dans ce produit par les
fentes du socle du téléphone ou du combiné,
car ils pourraient toucher des points de tension
dangereux ou créer un court-circuit. Ne jamais
renverser de liquide de quelque nature que ce
soit sur le produit.
12. Pour réduire le risque d'électrocution, ne
démontez pas ce produit, mais confiez-le à un
service après-vente agréé. Ouvrir ou retirer des
parties du socle du téléphone ou du combiné
autres que les portes d'accès spécifiées peut
vous exposer à des tensions dangereuses ou
à d'autres risques. Un remontage incorrect
peut provoquer une électrocution lors de
l'utilisation ultérieure du produit.
13. Ne surchargez pas les prises murales et les
rallonges électriques.
14. Débranchez ce produit de la prise murale et
confiez l'entretien à un centre de service agréé
dans les conditions suivantes :
• Lorsque le cordon d'alimentation ou la
fiche est endommagé ou effiloché.
• Si du liquide a été renversé sur le produit.
• Si le produit a été exposé à la pluie ou à
l'eau.
• Si le produit ne fonctionne pas normalement
en suivant les instructions d'utilisation.
Ne réglez que les commandes qui sont
couvertes par le mode d'emploi. Un
mauvais réglage des autres commandes
peut entraîner des dommages et nécessite
Instructions de sécurité importantes
La plaque signalétique appliquée est située au bas et à l'arrière de la base du produit.
Lorsque vous utilisez votre équipement téléphonique, des précautions de base doivent toujours être prises
pour réduire les risques d'incendie, d'électrocution et de blessure, notamment les suivantes
EN - 5
English
souvent un travail important de la part
d'un technicien autorisé pour remettre le
produit en état de fonctionnement.
• Si le produit est tombé et que le socle
du téléphone et/ou le combiné ont été
endommagés.
• Si le produit présente un changement
distinct de performance.
15. Évitez d'utiliser un téléphone (autre que sans
fil) pendant un orage électrique. Il existe un
risque d'électrocution dû à la foudre.
16. N'utilisez pas le téléphone pour signaler
une fuite de gaz à proximité de la fuite.
Dans certaines circonstances, une étincelle
peut se produire lorsque l'adaptateur est
branché dans la prise de courant, ou lorsque
le combiné est replacé dans son berceau. Il
s'agit d'un événement courant associé à la
fermeture de tout circuit électrique. L'utilisateur
ne doit pas brancher le téléphone dans
une prise de courant, ni placer un combiné
chargé dans son socle, si le téléphone est
situé dans un environnement contenant des
concentrations de gaz inflammables ou
propices aux flammes, à moins qu'il n'y ait une
ventilation adéquate. Une étincelle dans un
tel environnement pourrait créer un incendie
ou une explosion.
Ces environnements
peuvent comprendre
: l'utilisation médicale de
l'oxygène sans ventilation adéquate; les gaz
industriels (solvants de nettoyage; vapeurs
d'essence; etc.); une fuite de gaz naturel; etc.
17. Ne placez le combiné de votre téléphone près
de votre oreille que lorsqu'il est en mode de
conversation normal.
18. Les adaptateurs d'alimentation sont destinés
à être correctement orientés en position
verticale ou au sol. Les broches ne sont pas
conçues pour maintenir la fiche en place si
elle est branchée au plafond, sous la table ou
dans une prise de courant d'armoire.
19. Utilisez uniquement le cordon d'alimentation
et les piles indiqués dans ce manuel. Ne
jetez pas les piles au feu. Elles risquent
d'exploser. Vérifiez auprès des autorités
locales les éventuelles instructions spéciales
d'élimination.
20. En position de montage mural, veillez à
monter le socle du téléphone sur le mur en
alignant les oeillets avec les montants de
fixation de la plaque murale. Ensuite, faites
glisser le socle téléphonique vers le bas sur
les deux montants de montage jusqu'à ce
qu'il se verrouille en place. Reportez-vous
aux instructions complètes dans la section
Installation du guide d'utilisation.
21. Ce produit doit être installé à une hauteur
inférieure à 2 mètres.
22. Listé POE (Le produit est considéré comme peu
susceptible de nécessiter une connexion à un
réseau Ethernet avec un routage extérieur à
l'installation).
CAUTIONS
MISE EN GARDE
• Gardez les petits objets métalliques tels que
les épingles et les agrafes loin du combiné.
• Il peut y avoir un risque d'explosion si
un mauvais type de pile de combiné est
utilisé (
CTM-S2412, CTM-C4402
). Utilisez
uniquement la pile rechargeable fournie
(BT164392/BT264392) ou une pile de
remplacement (BT264392). Éliminez les piles
usagées conformément aux informations
figurant dans le sceau RBRC
MD
de ce guide
d'utilisation.
CONSERVEZ CES INSTRUCTIONS
EN - 6
Table of contents
Important safety instructions ............. 2
Instructions de sécurité importantes 4
Parts check list ....................................7
Telephone layout .............................. 8
SIP Contemporary Cordless 1-line -
CTM-S2412 ...................................................8
SIP Contemporary Cordless 1-line
Accessory Handset - CTM-C4402 ............ 8
Installation ....................................... 10
SIP Contemporary Cordless 1-line -
CTM-S2412 .................................................10
SIP Contemporary Cordless 1-line
Accessory Handset - CTM-C4402 ..........10
Cordless charging stand -
C4012 ..........................................................14
Set up ...............................................15
SIP Contemporary Cordless 1-line -
CTM-S2412 ................................................. 15
SIP Contemporary Cordless 1-line
Accessory Handset - CTM-C4402 ..........15
Voice Menu ...............................................16
Operation .........................................17
SIP Contemporary Cordless 1-line -
CTM-S2412 ................................................. 17
SIP Contemporary Cordless 1-line
Accessory Handset - CTM-C4402 .......... 17
Appendix ........................................ 20
Troubleshooting .......................................20
VTech Hospitality Limited Warranty
Program .....................................................26
Precautions for users of implanted
cardiac pacemakers ..................................28
Operating range .......................................28
About cordless telephones ....................28
The RBRC® seal .........................................29
FCC, ACTA and IC regulations ................29
Energy-saving charging mode .............. 32
Maintenance .............................................. 33
Disclaimer and Limitation of Liability ..... 33
Technical specifications .................. 34
SIP Contemporary Cordless 1-line -
CTM-S2412 .................................................34
SIP comtemporary cordless 1-line
accessory handset - CTM-C4402 ...........34
Cordless charging stand -
C4012 ..........................................................34
EN - 7
English
Parts check list
Items contained in the respective cordless telephone package:
Model name Model number
Parts included
Telephone base with
faceplate and overlay
Base Stand |
Wall Mount
Bracket
Network
cable
Cordless
handset and
Handset
battery
Handset
charging
stand |
Power
adapter
SIP
Contemporrary
Cordless 1-line
Hotel Phone
CTM-S2412
SIP
Contemporary
Cordless 1-line
Accessory
Handset and
Cordless
charging stand
CTM-S2415HC
(Virtual
Bundle of
CTM-C4402
and C4012)
BY 1021
BY 1021
EN - 8
1 Wall mount clip
2 Find Handset button
3 CHARGE LED
4 RJ-45 LAN port
5 Message waiting LED
6 RJ-45 COMPUTER port
7 USB CHARGE ONLY
(USB port for charging only)
Telephone layout
SIP Contemporary Cordless 1-line - CTM-S2412
SIP Contemporary Cordless 1-line Accessory Handset - CTM-C4402
Telephone Base
1
2
4
5
6
7
8 Numeric dial keys
9 Speed dial keys
10 Speed Dial key
11 REDIAL key
12 FLASH key
13 MUTE key
14 VOLUME + key
15 VOLUME – key
16 SPEAKER key
17 HOLD key
18 LINE key
19 Base power switch
3
10
11
8
9
17 16
15 13 12
14
18
19
EN - 9
English
Telephone layout
SIP Contemporary Cordless 1-line - CTM-S2412
SIP Contemporary Cordless 1-line Accessory Handset - CTM-C4402
Handset
1 Message waiting LED
2 Low battery LED
3 Handset earpiece
4 Microphone
5 Speakerphone
6TALK/FLASH key
7OFF/Cancel key
8 Numeric dial keys
9 SPEAKER key
10 Speed dial keys
11 VOLUME +/- keys
12 EMERGENCY key
13 HOLD key
14 MUTE key
15 MESSAGES key
1
2
5
4
7
8
9
10
11
13
14
6
3
15
12
EN - 10
Installation
SIP Contemporary Cordless 1-line -
CTM-S2412
SIP Contemporary Cordless 1-line
Accessory Handset - CTM-C4402
Installation option - install base stand
for desktop
To mount the telephone base on the base
stand
1. Turn the telephone base over with the bottom
side facing up.
2. Insert the lower tabs of the mounting bracket
into the lower grooves of the telephone base.
3. Press the upper tabs of the mounting bracket
and then push into the center of the telephone
base until it locks into place.
1 Charge LED
Cordless charging stand -
C4012
1
EN - 11
English
Telephone base installation
The telephone comes ready for desktop use.
1. Install the telephone base as shown below.
• Plug the Cat-5 network cable into the
RJ-45 LAN port on the telephone base
and the network wall jack with Power
over Ethernet (PoE).
1 Network wall jack with Power over
Ethernet (PoE)
2 Cat-5 network cable
3 RJ-45 LAN port
2. Once installed, the telephone begins an
initialization and system registration process.
If the system registration succeeds, the
telephone base will reboot.
If the system registration fails, the
key blinks twice every second. To reset,
disconnect the Cat-5 network cable
from the network wall jack with Power
over Ethernet (PoE) and then reconnect.
3. Press on the telephone base. Listen for a
dial tone, and then press again to hang
up.
Note
• The dial tone will not be played if the SIP
account used by this phone cannot be
registered.
CAUTIONS
Use only the supplied network cable. The
supplied network cable is not designed for
use in any other IT devices. Misusing it on
your other IT devices shall be prohibited.
To order a replacement, call 1-888-907-2007.
1
2
3
EN - 12
Installation option - converting
from desktop to wall mount position
To mount the telephone base on the wall
1. Unplug the Cat-5 network cable from the
network wall jack.
2. Remove the cordless handset from the
telephone base if it is cradled in the
telephone base. On the telephone base,
press the wall mount clip upward and rotate
a half turn (180°). Slide back the clip.
• It locks into place with the protruding
edge pointing towards the upper edge
of the telephone base. This protruding
edge holds the handset when the phone
is mounted on the wall.
3. Turn the telephone base over with the bottom
side facing up. To remove the mounting
bracket, firmly press down the tabs on the
mounting bracket and pull them out from the
grooves on the telephone base.
4. Mount the telephone base on the wall by
aligning the eyelets with the mounting studs
of the wall plate. Then slide the telephone
base down on both mounting studs until it
locks into place.
5. Plug the Cat-5 network cable back into the
network wall jack with Power over Ethernet
(PoE). Then replace the cordless handset on
the telephone base cradle.
1
1 Protruding edge
3
3 Eyelets
2
2 Mounting bracket
EN - 13
English
Handset battery installation
To install or replace the handset battery, follow
the steps below.
1. Use a narrow object to pry open the screw
cover and remove the screw with cross head
screwdriver. Then, insert a 5 mm standard
flat head screwdriver in the provided slot
and gently open the handset cover.
2. Unplug the battery connector from the
socket and then remove the battery from the
handset battery compartment.
3. Plug the battery connector securely into
the socket inside the handset battery
compartment. Place the battery with the
label THIS SIDE UP facing up and the wires
inside the battery compartment.
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT183342/BT283342 (2.4V 400mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1535
THIS SIDE UP
4. To replace the handset cover, align all
the tabs on the handset cover against the
corresponding grooves on the handset, then
firmly push downward until all the tabs lock
in the grooves. Then install the screw.
5. Bend a small paperclip and gently insert it
to the Handset battery ON pinhole to turn on
the handset.
• Without turning on the handset, the
handset cannot be charged or operate.
• The battery is fully charged after 16
hours of continuous charging. For best
performance, keep the cordless handset
in the telephone base when not in use.
CAUTIONS
• There may be a risk of explosion if a
wrong type of handset battery is used.
Use only the supplied rechargeable
battery (BT264392/BT266342) or
replacement battery (BT266342). To order
a replacement, call 1-888-907-2007.
• FCC ID is shown on the back of the
cordless handset body after the handset
cover is removed.
• Dispose of used batteries according to
the information in "The RBRC® seal" on
page 29.
Handset battery charging
The battery must be fully charged before using the
cordless handset for the first time. The CHARGE LED
turns on when the cordless handset is charging on
the telephone base. The battery is fully charged
after 16 hours of continuous charging. For best
performance, keep the cordless handset in the
telephone base or charging stand when not in
use.
EN - 14
Installation
Cordless charging stand - C4012
install charging stand for desktop
The charging stand is designed for desktop use.
Install the charging stand as shown below.
• Make sure the power adapter is securely
plugged into an outlet not controlled by
a wall switch.
CAUTIONS
Use only the supplied power adapter. The
supplied power adapter is not designed for
use in any other IT devices. Misusing it on
your other IT devices shall be prohibited.
To order a replacement, call 1-888-907-2007.
1
2
3
1 Electrical outlet not controlled by a wall switch
2 Power adapter
3 Power cord
Handset registration
Place the cordless handset on the telephone
base cradle. Handset registration happens
automatically the first time a cordless handset is
placed on the telephone base.
When the handset is successfully registered, a
confirmation tone will be heard.
Each telephone base accommodates up to
five cordless handsets. When you already have
five registered handsets, you can replace one
of them by a new handset if any one of the
five registered handsets is disconnected from
the base. For example, it is out of range, or its
battery is removed or depleted. The previous
registered handset is then deregistered from the
telephone base.
Register a handset to another telephone
base
Any CTM-C4402 handset can register to any
CTM-S2412 telephone base.
When a registered cordless handset is idle, place it
on another telephone base. This cordless handset
automatically registers to the new telephone base.
EN - 15
English
Set up
SIP Contemporary Cordless 1-line - CTM-S2412
SIP Contemporary Cordless 1-line Accessory Handset - CTM-C4402
Default settings are indicated by asterisks (*).
Setting Options Adjustable by
Listening volume- Handset 1, 2, 3, 4*, 5, 6 User and administrator
Speakerphone volume - Handset 1, 2, 3, 4*, 5, 6 User and administrator
Speakerphone volume - telephone base 1, 2, 3, 4, 5*, 6, 7, 8, 9 User and administrator
Ringer volume - telephone base 1, 2, 3, 4, 5*, 6, 7, 8, 9 User and administrator
Ringer tone Tone 1*, Tone 2, Tone 3 Administrator only
All telephone settings are programmed through the administrative web portal.
Please refer to the SIP Phone Configuration Guide for details.
EN - 16
Voice Menu
The Voice menu enables you to use the handset to query and change phone settings.
To access the Voice Menu:
1. When the phone is idle, press this key sequence on the handset: TALK Û Û Û Û.
A digitized voice on the handset will announce Voice Menu options.
2. Press the number key on the handset to select the desired menu option, or enter information.
A list of menu options is shown in the diagram below.
For example, to find out the IP address of the phone, press 1 for Network Configuration, then
press 2 for IP Address.
3. When you are finished with the Voice menu, press OFF on the handset or place it in the cradle.
NOTE: if you changed any network settings, your phone will automatically reboot.
This will enable your new settings to take effect.
7
So ware
Version
3
Factory Reset
1 Reset
Speed Dial to
Default*
2 Clear All
Speed Dial*
5
Reboot
* requires password
(default 1234)
1
Network
Confi gura on
2
IP Address*
3
Subnet Mask*
1
WAN Port Type
4
Gateway*
1 DHCP*
2 Sta c IP*
5
DNS*
2
Phone
Confi gura on
1
Phone Number
2
Server IP
Address
4
Call Forward
3
Port
4
Edit Speed Dial*
6
Web Access
Portal
1 Enable
2 Disable
EN - 17
English
Operation
SIP Contemporary Cordless 1-line -
CTM-S2412
SIP Contemporary Cordless 1-line
Accessory Handset - CTM-C4402
Using the cordless handset and the
telephone base
The cordless handset and the telephone base
speakerphone cannot be used at the same
time on a call. However, calls can be switched
between the cordless handset and the telephone
base speakerphone.
When the cordless handset or the telephone
base is in use, the TALK key on the cordless
handset and the LINE key on the telephone
base illuminate.
Receive a call
When there is an incoming call, the telephone
rings. The LINE key, key and the MESSAGE
WAITING LED on the telephone base flash, and
the TALK key on the cordless handset flashes.
Answer a call using the cordless handset
while it is not on the telephone base or
charging stand
On the cordless handset, press TALK key or .
• The TALK key illuminates when in use.
The key illuminates when in
speakerphone mode.
Answer a call using the cordless handset
while it is cradled on the telephone base or
charging stand
Lift the cordless handset from the telephone
base or charging stand.
• The TALK key illuminates when in use.
The key illuminates when in
speakerphone mode.
Answer a call using the telephone base
On the telephone base, press LINE key or .
• The LINE key illuminates when in use. The
key illuminates when in speakerphone
mode.
Place a call
Place a call using the cordless handset
On the cordless handset, press TALK key or
. Listen for a dial tone and then dial the desired
number, or press a Speed Dial key on the
cordless handset to dial a programmed number.
• The TALK key illuminates when in use.
The key illuminates when in
speakerphone mode.
Place a call using the telephone base
On the telephone base, press LINE key or .
Listen for a dial tone and then dial the desired
number, or press a Speed Dial key on the
telephone base to dial a programmed number.
• The LINE key illuminates when in
use. The key illuminates when in
speakerphone mode.
End a call
End a call when using the cordless handset
Press OFF on the cordless handset or place
it in the telephone base or charging stand.
The call ends when all handsets hang up.
End a call when using the telephone base
Press LINE key or .
Switch a call between the cordless
handset and the telephone base
speakerphone
• To switch a call from the cordless handset
to the telephone base speakerphone,
press on the telephone base.
EN - 18
• To switch a call from the telephone
base speakerphone to the cordless
handset which is not on the telephone
base cradle, press TALK or on the
cordless handset.
• To switch a call from the telephone base
speakerphone to the cordless handset
which is cradled on the telephone
base, lift the cordless handset from the
telephone base and press TALK or .
Join a call
During a call, press TALK or on another
cordless handset to join.
Handset speakerphone
During a call, press on the cordless handset
to switch between speakerphone mode and
handset earpiece mode. The key illuminates
when in speakerphone mode.
Redial
The last dialed number on the telephone base
is stored for 15 minutes.
Redial the last dialed number from the
telephone base
Press LINE or to listen for a dial tone. Then
press REDIAL.
Volume
Listening volume can be adjusted on the cordless
handset and the telephone base.
Adjust the listening volume
• During a call on the handset, press –
VOLUME + to adjust the listening volume.
The next call returns to the default listening
volume.
• During a call on the telephone base,
press VOLUME + or – to adjust the
listening volume. The next call returns to
the default listening volume.
Adjust the ringer volume of the telephone
base
Ringer volume of the telephone base can be
adjusted.
When the telephone base is idle, press VOLUME
+ or – to adjust the ringer volume.
Call waiting
Call waiting when using the cordless
handset
1. When you hear a call waiting tone during a
call, press TALK/FLASH key on the cordless
handset to put the current call on hold and
take the new incoming call.
2. To switch back and forth between calls, press
TALK/FLASH key.
3. To end the active call, press OFF, and then
press TALK/FLASH to resume the other call.
Call waiting when using the telephone base
1. When you hear a call waiting tone during a
call, press FLASH key on the telephone base
to put the current call on hold and take the
new incoming call.
2. To switch back and forth between calls, press
FLASH key.
3. To end the active call, press LINE key or
, and then press LINE key or again to
resume the other call.
Mute
Mute the microphone
1. During a call, press MUTE / .
• The MUTE / key on the handset /
telephone base illuminates when the
mute function is turned on. You can hear
the party on the other end, but they
cannot hear you.
2. Press MUTE / again to resume the
conversation.
• The light on the key turns off.
EN - 19
English
Message waiting Indicator
When a voice message is received, the message
waiting LEDs on the telephone base and the
cordless handset flashes.
Play messages
Press MESSAGES on the cordless handset in idle
mode to play messages.
Hold
To place a call on hold:
1. During a call, press the HOLD key on the
telephone base or the cordless handset.
• The TALK key on the cordless handset
and the LINE key on the telephone base
flash when the call is on hold.
To take the call off hold:
1. Press TALK or on the handset, OR press
LINE or on the telephone base or the call
will end automatically after the preset call on
hold duration.
• The TALK key illuminates when in use.
The key illuminates when in
speakerphone mode.
Find handset
Use this feature to find all registered cordless
handsets.
To start paging:
Press /FIND HANDSET on the telephone base
when the phone is not in use. All idle cordless
handsets ring for 60 seconds.
To end paging:
• Press /FIND HANDSET again on the
telephone base.
-OR-
• Press MUTE or OFF on the cordless
handset to stop the ringing.
Computer port
You can route your computer through the
COMPUTER port (RJ-45) on the side of the
telephone base to get Internet access.
USB port
The port on the side of the telephone base
can be used for charging devices (up to 500mA
@ 5V). Charging will be suspended when there
is an incoming call or the telephone is in use.
EN - 20
Appendix
Troubleshooting
If you have difficulty with the telephone, please try the suggestions below. For customer service, call
1-888-907-2007.
For cordless telephone
Question Suggestions
The telephone does not work at all.
• Make sure the Cat-5 network cable
is plugged into the LAN port of the
telephone base and the network wall
jack with Power over Ethernet (PoE).
• Make sure the battery is installed and
charged correctly. For optimum daily
performance, return the cordless handset
to the telephone base or charging stand
after use.
• Unplug the Cat-5 network cable from the
network wall jack. Wait for approximately
15 seconds, then plug it back in.
• Charge the battery in the cordless handset
for up to 16 hours.
• If the battery is completely depleted,
charge the battery for at least 30 minutes
before use.
• Remove the battery and then install it
again. If that still does not work, it may
be necessary to purchase a new battery.
• Disconnect the telephone base from the
network wall jack and connect a different
working SIP telephone. If the other SIP
telephone does not work, the problem is
probably in the wiring or network server.
Check your SIP server settings. Refer to
the SIP Phone Configuration Guide for
details.
• Make sure the energy-saving charging
mode is not activated. If this mode is
activated, all telephone functions will be
disabled, except battery charging.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
VTech CTM-S2412 Mode d'emploi
- Catégorie
- Téléphones
- Taper
- Mode d'emploi
dans d''autres langues
- English: VTech CTM-S2412 User guide