Somfy Sonesse 28 Mode d'emploi

Marque: Somfy

Modèle: Sonesse 28

Taper: Mode d'emploi

Sonesse 28 WF Zigbee

EN Instructions

ES Manual de instrucciones

FR Notice

EN Sonesse 28 WF Zigbee

ORIGINAL INSTRUCTIONS

These instructions apply to all Sonesse 28 Zigbee drives, the different versions of which are available in the current

catalogue.

CONTENTS

Prior information..........................................................................................................................................................

1.1.

Field of application..........................................................................................................................................

1.2.

Liability .............................................................................................................................................................

Installation.....................................................................................................................................................................

2.1.

Assembly ..........................................................................................................................................................

2.2.

Wiring ...............................................................................................................................................................

2.3.

Commissioning of a Zigbee drive ..................................................................................................................

2.4.

Commissioning with TaHoma pro application (recommended)................................................................

2.5.

Commissioning with a control point only (without TaHoma pro application)........................................

2.6.

Tips and advice on installation.......................................................................................................................

Use and maintenance ...................................................................................................................................................

3.1.

Use with TaHoma switch solution ................................................................................................................

3.2.

Use with TaHoma ready solution..................................................................................................................

3.3.

Tips and advice on operation.........................................................................................................................

Technical data ...............................................................................................................................................................

GENERAL INFORMATION

Safety instructions

DANGER

Indicates a danger which may result in immediate death or serious injury.

WARNING

Indicates a danger which may result in death or serious injury.

PRECAUTION

Indicates a danger which may result in minor or moderate injury.

CAUTION

Indicates a danger which may result in damage to or destruction of the product.

Sonesse 28 WF Zigbee EN

1.PRIOR INFORMATION

1.1.Field of application

The Sonesse 28 drives are designed to motorise all types of:

▪

Interior vertical blinds which front rail moves solely by gravity with a mass less than 15kg.

▪

Tiltable venetian blinds which bottom lath can be lifted at least by 4cm when an upward force of 150N is applied to

the bottom lath positioned at 16cm from the fully extended position.

1.2.Liability

Before installing and using the drive, please read these instructions carefully.

In addition to the instructions provided in this guide, please also comply with the instructions provided in the attached Safety

instructions document.

The drive must be installed by a home motorisation and automation professional, in accordance with Somfy’s

instructions and the applicable regulations in the country of installation.

Any operation of the drive outside the field of application described above is prohibited. Such use, and any failure to comply

with the instructions given in this guide and in the attached Safety instructions document, absolves Somfy of any liability and

invalidates the warranty.

After installing the drive, the installer must inform his customers of the operating and maintenance conditions for the drive

and must provide them with the operating and maintenance instructions, and the attached Safety instructions document.

Any After-Sales Service operation on the drive must be performed by a home motorisation and automation professional.

Never begin installing without first checking the compatibility of this product with the associated equipment and

accessories. If in doubt when installing this product and/or to obtain additional information, contact a Somfy representative

or visit the website www.somfy.com.

Using this drive with any products which are not listed in the attached «Compatibility matrix» document shall also

render invalid any Somfy warranty and release Somfy from any liability.

2.INSTALLATION

WARNING

•

These instructions are mandatory for the home motorisation and automation professional installing the drive.

•

Comply with current standards and legislation in the country of installation.

CAUTION

•

Never drop, knock or puncture the drive or immerse it in liquid.

•

Install an individual control point for each drive.

NOTICE

Make sure that LED, programming button and input connection remain visible and easily accessible after installation.

2.1.Assembly

2.1.1.Preparing the drive

CAUTION

Sonesse 28 Zigbee : interior diameter of the tube has to be Ø26.6 mm or greater.

1] Fit the crown (a) and drive wheel (b) to the motor.

2] Measure the length (L) between the end of the drive wheel and the head end.

(a)(b)

EN Sonesse 28 WF Zigbee

2.1.2.Preparing the tube

1] Cut the tube to the required length.

2] Deburr the tube and remove the debris.

1] 2]

2.1.3.Assembling the drive-tube

1] Slide the drive into the tube. Insert the wheel by aligning the wheel to the tube

profile. Insert the drive half way and then slide the crown down the drive and

insert it in the tube. Finally, push the motor inside the tube.

2] Not required, but if needed, fix the tube to the drive with self-tapping screws

or steel pop rivets depending on the dimension (L).

2.1.4.Mounting the tube-drive assembly on the brackets

(a) Standard bracket.

(b) Drive plate for specific bracket.

(a) (b)

NOTICE

For optimal radio reception, the motor antenna should be kept straight and should be positioned outside of headrail

(if used).

2.2.Wiring

WARNING

•

To ensure electrical safety, this Class III drive must be powered by a «SELV» voltage source (Safety Extra Low

Voltage).

•

For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance.

•

Improper using battery pack may cause overheat, fire, explosion, resulting in serious injury or death.

•

Do not expose the drive or battery to excessive temperatures.

•

There is a risk if terminals of the battery-operated drive or battery being short circuited by metal objects.

•

Ensure battery is fully charged prior to installation on site.

PRECAUTION

•

Cables which pass through a metal wall must be protected and isolated using a sheath or sleeve.

•

Attach cables to prevent any contact with moving parts.

•

Drive cable cannot be removed. If it is damaged, return the drive to the After-Sales department.

CAUTION

•

Do not unplug the battery when the motor works.

•

Leave the drive power supply cable accessible: the product must be easily replaceable.

•

Using this drive with any products which are not listed in the attached «Compatibility matrix» document shall also

render invalid any Somfy warranty and release Somfy from any liability.

Sonesse 28 WF Zigbee EN

Plug the battery with the motor supply cable.

2.3.Commissioning of a Zigbee drive

In an installation with Zigbee drives, 2 solutions are available to the user: TaHoma switch solution and TaHoma ready

solution.

TaHoma switch solution is the solution in connected mode, with a TaHoma switch in the installation that allows the user to

control all his Zigbee products through the TaHoma application.

The other solution, without TaHoma switch, is called TaHoma ready. It allows the user to control his Zigbee drives only

with control points. But this installation can be switched to connected mode afterwards by adding a TaHoma switch later.

Regarding the commissioning of a Zigbee drive, it can be done in 2 different ways :

▪

Either commissioning with TaHoma pro application, which is recommended because it is easier and more complete.

▪

Either commissioning with a control point.

Please refer to the corresponding section according to the selected commissioning mode.

2.4.Commissioning with TaHoma pro application (recommended)

Commissioning with TaHoma pro application is possible and recommended for both TaHoma ready solution

and TaHoma switch solution.

2.4.1.Starting-up

A Somfypro account is required but TaHoma switch is not mandatory.

To set the drive, you need to access and use TaHoma pro application, you must have a compatible phone or mobile device

and access to the internet.

The application is downloadable for free from Apple Store platforms and Google Play Store on Apple or Android™

compatible mobile devices. This compatibility is the one indicated in the description of the application on the corresponding

Store.

The software version of the TaHoma pro application may be updated from time to time to add new features and services.

2.4.2.Setting the drive

CAUTION

•

Download TaHoma pro application if it is not yet installed on the smartphone.

•

Launch the TaHoma pro application before performing this step.

1] Plug in the power supply of the drive.

If the drive is not set or paired, once plugged in, it goes into programming

mode during 3min, and its LED blinks orange.

2] Open the TaHoma pro application and follow the steps to scan the drive QR

code.

3] Follow the instructions on the TaHoma pro application.

EN Sonesse 28 WF Zigbee

NOTICE

This drive can be set with TaHoma pro and used without TaHoma switch (TaHoma switch can be added later).

2.4.3.Network management

To pair a control point to the drive, to add a new control point or a new drive in the installation, follow the instructions on

the TaHoma pro application.

2.4.4.Advanced settings

The TaHoma pro application is the recommended tool to easily set the drive and perform re-settings such as modifying the

direction of rotation of the drive, or readjusting the end limits.

On the other hand, some advanced settings such as adjusting the speed or the tilting travel can only be made via the

TaHoma pro application.

Follow the instructions in the TaHoma pro application to perform these settings or re-settings.

2.5.Commissioning with a control point only (without TaHoma pro

application)

This chapter describes the commissioning of the drive with a control point only, without using TaHoma pro

application, in the case of TaHoma ready solution.

2.5.1.Link creation between a drive and a control point

The following steps describe how to program a drive that is not set or paired, with an unpaired control point.

CAUTION

Settings are not possible if the control point batteries are too low.

1] Plug in the power supply of the drive.

If the drive is not set or paired, once plugged in, it goes into programming

mode during 3min, and its LED blinks orange.

NOTICE

If the drive has left the programming mode, its LED is not blinking:

•

Press and hold the PROG button on the drive until the motorised product

moves up and down briefly and its LED blinks orange : the drive is in

programming mode during 3min.

2] Bring the control point close to the drive then briefly press simultaneously

the Up and Down buttons on the control point: the control point looks for

the closest drive in programming mode.

When found, the feedback LED on the control point blinks in green, the

drive LED flashes in green, and the motorised product moves up and

down briefly.

Then the feedback LED on the control point blinks in orange slowly as

long as it is in setting mode.

NOTICE

If the control point does not find a drive nearby, the feedback LED of the control point blinks red after a few seconds,

and the motorised product of the drive does not move: repeat the above procedure. (If the drive is still in

programming mode, repeat only step 2).

NOTICE

If the control point does not find the right drive, please refer to chapter Scanning mode.

Sonesse 28 WF Zigbee EN

2.5.2.Scanning mode

If several drives are in programming mode, it is possible to be in setting mode with an

undesired drive.

1] Make sure the drive to be paired is still in programming mode. Otherwise,

restart from the beginning of commissioning steps.

2] If the drive to be paired is still in programming mode, bring the control point

close to the drive then briefly press the Up and Down buttons on the

control point simultaneously to exit the setting mode with the previous drive

and scan another close Zigbee drive.

The motorised product of the new found drive moves up and down

briefly, the drive is in setting mode.

A B C

B C …

2.5.3.Checking the direction of rotation

Press the Up button on the control point:

a] If the motorised product rises, the direction of rotation is correct: move onto

section Setting the end limits.

b] If the motorised product lowers, the direction of rotation is incorrect: move onto

the next step.

b1] Press the my button on the control point until the motorised product moves up

and down: The direction of rotation has been modified.

b2] Press the Up button on the control point to check the direction of rotation.

b1] b2]

2.5.4.Setting the end limits and pairing the control point

NOTICE

The end limits can be set in any order.

EN Sonesse 28 WF Zigbee

1] Press and hold the Up button to move the motorised product to the desired

up position. If necessary, adjust the up position using the Up or Down

buttons.

2] Press the my and Down buttons simultaneously until the motorised product

briefly moves up and down.

The upper end limit is memorised.

3] Press and hold the Down button to move the motorised product to the

desired lower position. If necessary, adjust the lower position using the Up or

Down buttons.

4] Press the my and Up buttons simultaneously until the motorised product

briefly moves up and down.

The lower end limit is memorised.

▪

To confirm and exit the setting and pair the control point: briefly press the

PROG button of the control point:

◦

→ The motorised product briefly moves up and down: the drive is now set

and can be controlled using the control point.

▪

To confirm and exit the setting without pairing the control point: press and

hold the Up and Down buttons on the control point simultaneously, until the

feedback LED on the control point stops flashing.

◦

→ The drive is now set and no control point is paired. (To pair the first control

point with an already set drive, refer to the following section).

1] 2]

3] 4]

2.5.5.Pairing the first control point to an already set drive

CAUTION

This procedure cannot be performed on multiple drives at the same time.

NOTICE

Keep the control point close to the drive during the whole procedure.

1] Press and hold the PROG button on the drive until the motorised product

moves up and down briefly and its LED blinks orange: the drive is in

programming mode during 3min.

2] Briefly press the PROG button on the control point: the motorised product

moves up and down briefly.

The drive can now be controlled using the control point.

2.5.6.Creating a network with TaHoma ready: add control points and drives in

the installation

▪

To add a new single-channel or multichannel control point to the drive or to delete one of its paired control points:

refer to the control point instruction guide.

▪

To pair additional drives: follow the same procedure of commissioning with a new control point for each drive and

refer to the control point instruction guide to have them share the same network.

2.5.7.Modifying the direction of rotation with a control point

CAUTION

•

This procedure cannot be performed on multiple drives at the same time.

•

The drive must be set and paired to the control point.

Sonesse 28 WF Zigbee EN

NOTICE

Keep the control point close to the drive during the whole procedure.

1] Press and hold the PROG button on the control point until the motorised

product moves up and down.

2] Briefly press the Up and Down buttons simultaneously on the control point :

The motorised product moves up and down after a few seconds.

3] Press the my button on the control point until the motorised product moves

up and down:

The direction of rotation has been modified.

4] To confirm and exit the setting, press and hold the Up and Down buttons on

the control point simultaneously, until the feedback LED on the control point

stops flashing.

5] Press the Up button on the control point to check the direction of rotation.

2] 3]

4] 5]

2.5.8.Readjusting the end limits with a control point

CAUTION

•

This procedure cannot be performed on multiple drives at the same time.

•

The drive must be set and paired to the control point.

NOTICE

Both end limits can be readjusted: either only one of them, or both at the same time.

2.5.8.1. Readjusting the upper end limit

NOTICE

Keep the control point close to the drive during the whole procedure.

1] Press and hold the PROG button on the control point until the motorised

product moves up and down.

2] Briefly press the Up and Down buttons simultaneously on the control point :

The motorised product moves up and down after a few seconds.

3] Press and hold the Up or Down button on the control point to move the

motorised product to the new desired position.

4] Briefly press the my and Down buttons simultaneously on the control point :

The motorised product moves up and down.

5] To confirm and exit the setting, press and hold the Up and Down buttons on

the control point simultaneously, until the feedback LED on the control point

stops flashing.

3] 4]

2.5.8.2. Readjusting the lower end limit

NOTICE

Keep the control point close to the drive during the whole procedure.

EN Sonesse 28 WF Zigbee

1] Press and hold the PROG button on the control point until the motorised

product moves up and down.

2] Briefly press the Up and Down buttons simultaneously on the control point :

The motorised product moves up and down after a few seconds.

3] Press and hold the Up or Down button on the control point to move the

motorised product to the new desired position.

4] Briefly press the Up and my buttons simultaneously on the control point :

The motorised product moves up and down.

5] To confirm and exit the setting, press and hold the Up and Down buttons on

the control point simultaneously, until the feedback LED on the control point

stops flashing.

3] 4]

2.5.8.3. Readjusting the two end limits

NOTICE

Keep the control point close to the drive during the whole procedure.

1] Press and hold the PROG button on the control point until the motorised

product moves up and down.

2] Briefly press the Up and Down buttons simultaneously on the control point :

The motorised product moves up and down after a few seconds.

3] Press and hold the Up or Down button on the control point to move the

motorised product to the new desired upper position.

4] Briefly press the my and Down buttons simultaneously on the control point :

The motorised product moves up and down.

The upper end limit is readjusted.

5] Press and hold the Up or Down button on the control point to move the

motorised product to the new desired lower position.

6] Briefly press the Up and my buttons simultaneously on the control point :

The motorised product moves up and down.

The lower end limit is readjusted.

7] To confirm and exit the setting, press and hold the Up and Down buttons on

the control point simultaneously, until the feedback LED on the control point

stops flashing.

1] 2]

3] 4]

5] 6]

2.5.9.Advanced settings

Some advanced settings such as adjusting the speed or the tilting travel cannot be made with a control point.

These advanced settings can only be made via the TaHoma pro application, please refer to chapter Commissionning with

TaHoma pro application (recommended).

Sonesse 28 WF Zigbee EN

2.6.Tips and advice on installation

2.6.1.Questions about the product?

Observations Possible causes Solutions

The motorised product is noisy. The wheel and the crown are not

adapted to the used tube.

Change the wheel and the crown.

The mechanical plays between drive,

accessories, tube and end of tube are

too high.

The mechanical plays between drive,

accessories, tube and end of tube must

be decreased to the minimum.

The wheel is not properly fixed to the

tube.

Fix the wheel properly to the tube.

The equipment is constrained between

the brackets.

Decrease the constraint between the

brackets.

The length of the notch is not adapted

to the drive hook or to the used crown.

Adapt the length of the notch to the

drive hook or to the used crown.

Debris, screws or other are in the tube. Empty the tube.

The temperature of the environment is

not in conformity with the operating

temperature.

Change the environment temperature.

The motorised product stops too soon

or too late.

The end limits of the motorised product

slip.

Readjust the end limits referring to

Commissioning of a Zigbee drive

End-limits are not properly adjusted. Readjust the end limits referring to

Commissioning of a Zigbee drive

The motorised product is not within the

recommended weight limits.

Check the compatibility of the

motorised product. Consult a Somfy

contact or visit www.somfy.com.

EN Sonesse 28 WF Zigbee

Observations Possible causes Solutions

The motorised product does not work. Wiring is incorrect. Check the wiring and modify it if

necessary.

The drive is neither set nor paired. Proceed to Commissioning of a

Zigbee drive

The drive is paired but not set. Proceed to Commissioning of a

Zigbee drive

The drive is set but not paired Proceed to Commissioning of a

Zigbee drive

The drive is in thermal protection mode.

Red LED = ON then lights OFF.

Wait for the drive to cool down.

An obstacle hinders the movement of

the motorised product. The red LED

blinks.

Remove the obstacle.

Drive position is out of the end limits.

Red LED blinks 2 times intermittently

and continually.

Readjust the end limits referring to

Commissioning of a Zigbee drive

The control point battery is low. LED

doesn't light when any button of a

paired control point is pressed.

Check the battery of the control point

and replace it as required.

The control point is not compatible or

not programmed.

Check the compatibility or pair the

control point as required referring to

Commissioning of a Zigbee drive

2.6.2.Upgrading a TaHoma ready installation into a TaHoma switch installation

To add TaHoma switch into a TaHoma ready installation, and then upgrade the installation into a TaHoma switch

installation, follow the instructions on the TaHoma pro application.

2.6.3.Erasing the memory of the drive (reset to original configuration)

NOTICE

This reset deletes all paired control points, end limit settings, advanced settings and resets the drive’s favourite

position (my).

Press and hold the PROG button on the drive until its LED blinks orange and the

motorised product briefly moves up and down 3times.

➔ All the settings are erased. The drive is reset to its original configuration.

➔ The drive is in programming mode during 3min, and its LED blinks orange.

Resume the commissioning procedure (Refer to Commissioning of a Zigbee drive).

3.USE AND MAINTENANCE

NOTICE

This drive does not require any maintenance operations.

The way to control a Zigbee motorised product is different depending on the solution present in the installation: TaHoma

switch solution or TaHoma ready solution.

Please refer to the corresponding section according to the solution.

Sonesse 28 WF Zigbee EN

3.1.Use with TaHoma switch solution

3.1.1.Use with TaHoma application

To control the motorised product in connected mode, you need to access and use TaHoma application, you must have a

compatible phone or mobile device and access to the internet.

The application is downloadable for free from Apple Store platforms and Google Play Store on Apple or Android™

compatible mobile devices. This compatibility is the one indicated in the description of the application on the corresponding

Store.

The software version of the TaHoma application may be updated from time to time to add new features and services.

1] Download TaHoma application if it is not yet installed on the smartphone.

2] Launch the application and follow the instructions to control the motorised

product.

1] 2]

3.1.2.Use with a control point

Up and Down buttons

1] For tiltable motorised products:

▪

Briefly press the Up or Down button on the control point to raise or lower

the motorised product fully.

▪

Press and hold the Up or Down button on the control point until the

motorised product reaches the desired position. The movement stops when

the button is released.

2] For other motorised products:

▪

Briefly press the Up or Down button on the control point to raise or lower

the motorised product fully.

Stop function

▪

Briefly press the my button on the control point to stop the motorised

product.

Favourite position (my)

NOTICE

An intermediate stop, which is called the “favourite position (my)”, is different from the upper and lower positions.

Programming or modifying the favourite position (my)

NOTICE

Only one favourite position (my) is permitted.

EN Sonesse 28 WF Zigbee

1] Move the motorised product to the desired favourite position using the Up or

Down button.

2] Briefly press the my button to stop the motorised product.

3] Press and hold the my button until the motorised product briefly moves up

and down:

The desired favourite position (my) is programmed and green LED blinks

5times.

2] 3]

Using the favourite position (my)

▪

If a favourite position (my) is programmed, briefly press the my button on the

control point twice in succession to move the motorised product to the

favourite position (my).

x 2 =

3.2.Use with TaHoma ready solution

Up and Down buttons

▪

Briefly press the Up or Down button on the control point to raise or lower

the motorised product fully.

▪

Press and hold the Up or Down button on the control point until the

motorised product reaches the desired position. The movement stops when

the button is released.

Stop function

▪

Briefly press the my button on the control point to stop the motorised

product.

Favourite position (my)

NOTICE

An intermediate stop, which is called the “favourite position (my)”, is different from the upper and lower positions.

Programming or modifying the favourite position (my)

NOTICE

Only one favourite position (my) is permitted.

1] Move the motorised product to the desired favourite position using the Up or

Down button.

2] Briefly press the my button to stop the motorised product.

3] Press and hold the my button until the motorised product briefly moves up

and down:

The desired favourite position (my) is programmed and green LED blinks

5times.

2] 3]

Sonesse 28 WF Zigbee EN

Using the favourite position (my)

▪

If a favourite position (my) is programmed, briefly press the my button on the

control point twice in succession to move the motorised product to the

favourite position (my).

x 2 =

3.3.Tips and advice on operation

3.3.1.Questions about the product?

Observations Possible causes Solutions

The motorised product does not

operate.

The control point battery is low. Check the battery and replace it as

required.

Drive battery is low and requires charge.

Red LED blinks 3times when any button

of a paired control point is pressed.

Plug in the charger.

The thermal protection has activated. Wait for the drive to cool down.

The motorised product stops before its

end limit.

Drive battery is low and requires charge.

Red LED blinks 3 times when any button

of a paired control point is pressed.

Plug in the charger.

NOTICE

If the motorised product still does not work, contact a drive and home automation professional.

3.3.2.Upgrading a TaHoma ready installation into a TaHoma switch installation

To add a TaHoma switch into a TaHoma ready installation, and then upgrade the installation into a TaHoma switch

installation, follow the instructions on the TaHoma application.

4.TECHNICAL DATA

Power supply 12 Vdc class 2 power supply SELV + LPS

Radio frequency 2.4 GHz

Frequency bands and maximum power used 2.4 GHz - 2.4835 GHz e.r.p < 10mW

Torque 1.1 N·m

Speed 10-28 RPM

Minimum distance between limits 1 turn

Zigbee version 3.0

Bluetooth® version 4.2

Electric insulation III

Operating temperature 0° to 60°

Protection rating IP20 (for indoor use only)

Charging temperature 0° / 45° C

NOTICE

For additional information on the technical data for this drive contact your Somfy representative.

Please separate storage cells and batteries from other types of waste and recycle them via the local collection

facility.

EN Sonesse 28 WF Zigbee

We care about our environment. Do not dispose of the appliance with usual household waste. Give it to an

approved collection point for recycling.

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of

such marks by SOMFY ACTIVITIES SA is under license. Other trademarks and trade names are those of their

respective owners.

Reference Designation

1241754 Sonesse 28 Zigbee

1241672 Sonesse 28 Zigbee

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

FCC warning statement:

- This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including

interference that may cause undesired operation.

- This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must

follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located

or operating in conjunction with any other antenna or transmitter.

- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority

to operate the equipment.

FCC RF RADIATION EXPOSURE STATEMENT: This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between

the radiator and any part of your body.

ISED WARNING STATEMENTS: This equipment complies with IC RSS-102 radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between

the radiator and any part of your body.

Apple and Apple logos are trademarks of Apple, Inc., registered in the U.S. and other countries.

iPad® and iPhone® are registered trademarks of Apple, Inc. App Store is a service mark of Apple Inc.

Android is a trademark of Google LLC.

https://developer.android.com/distribute/marketing-tools/brand-guidelines

US Patents , patent pending.

Sonesse 28 WF Zigbee ES

MANUAL TRADUCIDO

Este manual es aplicable a todas las motorizaciones Sonesse 28 Zigbee, cuyas versiones se encuentran disponibles en el

catálogo actual.

ÍNDICE

Información previa .......................................................................................................................................................

1.1.

Ámbito de aplicación.......................................................................................................................................

1.2.

Responsabilidad...............................................................................................................................................

Instalación .....................................................................................................................................................................

2.1.

Montaje ............................................................................................................................................................

2.2.

Cableado...........................................................................................................................................................

2.3.

Puesta en marcha de un motor Zigbee.........................................................................................................

2.4.

Puesta en marcha con la aplicación TaHoma Pro (recomendado) ............................................................

2.5.

Puesta en marcha con solo un punto de mando (sin la aplicación Tahoma Pro).....................................

2.6.

Trucos y consejos de instalación ...................................................................................................................

Uso y mantenimiento...................................................................................................................................................

3.1.

Uso con la solución TaHoma Switch.............................................................................................................

3.2.

Uso con la solución TaHoma Ready..............................................................................................................

3.3.

Trucos y consejos de uso................................................................................................................................

Características técnicas................................................................................................................................................

INFORMACIÓN GENERAL

Normas de seguridad

PELIGRO

Señala un peligro que provoca inmediatamente la muerte o lesiones graves.

ADVERTENCIA

Señala un peligro susceptible de provocar la muerte o lesiones graves.

PRECAUCIÓN

Señala un peligro susceptible de provocar lesiones leves o moderadamente graves.

ATENCIÓN

Señala un peligro susceptible de dañar o destruir el producto.

ES Sonesse 28 WF Zigbee

1.INFORMACIÓN PREVIA

1.1.Ámbito de aplicación

Las motorizaciones Sonesse 28 están diseñadas para motorizar todo tipo de:

▪

Persianas verticales interiores cuyo riel delantero se mueve únicamente por la gravedad con una masa inferior a

15kg.

▪

Persianas venecianas inclinables cuyo listón inferior pueda elevarse al menos 4 cm cuando se aplica una fuerza

ascendente de 150 N al listón inferior, situado a 16 cm de la posición totalmente extendida.

1.2.Responsabilidad

Antes de instalar y utilizar la motorización, lea detenidamente estas instrucciones.

Además de las instrucciones que figuran en esta guía, siga también las instrucciones que figuran en el documento adjunto

Normas de seguridad.

La motorización debe instalarla un profesional de la motorización y automatización de la vivienda de acuerdo con

las instrucciones de Somfy y la normativa vigente aplicable en el país de instalación.

Queda prohibido utilizar el motor fuera de cualquier campo aplicación arriba descrito. Ello conllevaría, como todo

incumplimiento de las instrucciones que figuran en este manual y en el documento adjunto Normas de seguridad, la

exclusión de toda responsabilidad por parte de Somfy y la anulación de la garantía.

Tras la instalación del motor, el instalador deberá informar a sus clientes de las condiciones de uso y de mantenimiento y

hacerles entrega de las instrucciones de uso y mantenimiento, así como del documento adjunto Normas de seguridad.

Cualquier operación del Servicio posventa en la motorización requerirá la intervención de un profesional de la motorización

y la automatización de la vivienda.

Antes de su instalación, compruebe la compatibilidad de este producto con los equipos y accesorios asociados. Para

resolver cualquier duda que pudiera surgir durante la instalación de este producto o para obtener información adicional,

póngase en contacto con uno de los agentes de Somfy o visite la página web www.somfy.com.

El uso de este motor con productos no incluidos en el documento adjunto «Matriz de compatibilidad» conllevaría

la exclusión de cualquier responsabilidad por parte de Somfy y la anulación de la garantía.

2.INSTALACIÓN

ADVERTENCIA

•

Instrucciones que debe seguir obligatoriamente el profesional de la motorización y la automatización de la

vivienda que efectúe la instalación de la motorización.

•

Se deben seguir las normas y la legislación vigentes en el país de instalación.

ATENCIÓN

•

Nunca deje caer, golpee, perfore ni sumerja en líquido la motorización.

•

Instale un punto de mando individual para cada motorización.

AVISO

Después de la instalación, debe asegurarse de que el LED, el botón de programación y la conexión de entrada sean visibles y

fácilmente accesibles.

2.1.Montaje

2.1.1.Preparación de la motorización

ATENCIÓN

Sonesse 28 Zigbee : el diámetro interior del tubo debe ser de 26.6 mm o superior.

Sonesse 28 WF Zigbee ES

1] Introduzca la corona (a) y la rueda motriz (b) en el motor.

2] Mida la longitud (L) entre el extremo de la rueda motriz y el extremo del

cabezal.

(a)(b)

2.1.2.Preparación del tubo

1] Corte el tubo a la longitud deseada.

2] Desbarbe el tubo y retire los fragmentos.

1] 2]

2.1.3.Montaje del conjunto motorización-tubo

1] Deslice la motorización dentro del tubo. Inserte la rueda alineándola con el

perfil del tubo. Inserte la motorización hasta la mitad y, a continuación, deslice

la corona hacia abajo en la motorización e insértela en el tubo. Por último,

introduzca el resto del motor en el interior del tubo.

2] No es obligatorio, pero si fuera necesario, fije el tubo a la motorización por

medio de tornillos autorroscantes o remaches de acero en función de la

dimensión (L).

2.1.4.Montaje del conjunto tubo-motorización en los soportes

(a) Soporte estándar.

(b) Placa de la motorización para soporte específico.

(a) (b)

AVISO

Para una recepción óptima de la radio, la antena del motor debe estar recta y situada fuera del cabezal (en caso de

utilizarse).

2.2.Cableado

ADVERTENCIA

•

Para garantizar la seguridad eléctrica, este motor de clase III debe accionarse mediante una fuente de tensión

«SELV» (tensión extra-baja de seguridad).

•

Para cargar la batería, utilice únicamente la unidad de alimentación desmontable que se entrega con este aparato.

•

Un uso inadecuado del tubo de las baterías puede ocasionar sobrecalentamiento, un incendio o una explosión y,

como consecuencia de ello, lesiones graves o incluso mortales.

•

No exponga la motorización o la batería a temperaturas extremas.

•

Existe riesgo de cortocircuito si los terminales de la batería o la motorización que funciona con baterías entran en

contacto con objetos metálicos.

•

Asegúrese de que la batería esté totalmente cargada antes de su instalación.

PRECAUCIÓN

•

En caso de que los cables deban atravesar una pared metálica, deben protegerse y aislarse con un tubo corrugado

o un pasamuros.

•

Fije los cables para evitar cualquier contacto con un componente en movimiento.

•

El cable del motor no es desmontable. Si está dañado, debe devolver el motor al Servicio Posventa (SPV).

ES Sonesse 28 WF Zigbee

ATENCIÓN

•

No desenchufe la batería con el motor en funcionamiento.

•

Deje accesible el cable de alimentación de la motorización: el producto debe sustituirse fácilmente.

•

El uso de este motor con productos no incluidos en el documento adjunto «Matriz de compatibilidad» conllevaría

la exclusión de cualquier responsabilidad por parte de Somfy y la anulación de la garantía.

Enchufe la batería con el cable de alimentación del motor.

2.3.Puesta en marcha de un motor Zigbee

En una instalación con motores Zigbee, el usuario dispone de 2 soluciones: solución TaHoma switch y solución TaHoma

ready.

La solución TaHoma switch es la que está en modo conectado, con un TaHoma switch en la instalación que permite al

usuario controlar todos sus productos Zigbee a través de la aplicación TaHoma.

La otra solución, sin TaHoma switch, se llama TaHoma ready. Permite al usuario controlar sus motores Zigbee solo con los

puntos de mando. No obstante, esta instalación se puede cambiar posteriormente al modo conectado añadiendo un

TaHoma switch más tarde.

En cuanto a la puesta en marcha de un motor Zigbee, puede hacerse de dos formas distintas:

▪

realizar la puesta en marcha con la aplicación TaHoma pro, lo que es recomendable porque es más fácil y completa; o

también

▪

realizar la puesta en marcha con un punto de mando.

Consulte la sección correspondiente según el modo de puesta en marcha seleccionado.

2.4.Puesta en marcha con la aplicación TaHoma Pro (recomendado)

La puesta en marcha con la aplicación TaHoma pro es posible y se recomienda tanto para la solución

TaHoma ready como para la solución TaHoma switch.

2.4.1.Inicio

Se requiere una cuenta Somfypro, pero el TaHoma switch no es obligatorio.

Para configurar el motor, debe acceder y utilizar la aplicación TaHoma pro para ello, debe disponer de un teléfono o

dispositivo móvil compatible y conectarse a Internet.

Puede descargar la aplicación de forma gratuita desde las plataformas de Apple Store y Google Play Store en dispositivos

móviles compatibles con Apple o Android™. Esta compatibilidad es la indicada en la descripción de la aplicación en la Store

correspondiente.

La versión de software de la aplicación TaHoma pro puede actualizarse en cualquier momento para añadir nuevas funciones

y servicios.

2.4.2.Ajuste del motor

ATENCIÓN

•

Descargue la aplicación TaHoma pro si no la tiene instalada en su teléfono móvil.

•

Inicie la aplicación TaHoma pro antes de realizar este paso.

La page charge ...

Somfy Sonesse 28 Mode d'emploi

Marque: Somfy

Modèle: Sonesse 28

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Somfy Sonesse 28 Operating instructions
español: Somfy Sonesse 28 Instrucciones de operación

Somfy Sonesse 28 Mode d'emploi

Somfy Sonesse 28 Mode d'emploi

dans d''autres langues

Documents connexes