Daintree WWD2-4IW Guide d'installation

Taper
Guide d'installation
Daintree® Wireless Controls
Wireless Scene Switch
Product Overview
The Daintree® Wireless Scene Switch is a battery-powered wall switch for use in a Daintree Networked or Daintree EZ
Connect application. The WWD2-4IW device installs into an existing junction box to replace the existing wall-mounted
switch with a wireless solution that enables on/off and either dimming or scene selection commands to be delivered to
the luminaires in its commissioned space. The WWD2-4IW device can provide either dual zone dimming control or allow
the user to select from four configured scenes. The buttons on the WWD2-4IW can be changed to clearly indicate the
operation mode of the device. The communication with the Daintree EZ Connect or Daintree Networked system utilizes
a secure and reliable wireless connection which helps minimize installation costs and complexity.
DT043
Prepare Electrical Wiring
Electrical Requirements
• When replacing a line voltage switch, the
power must be off at the branch circuit
breaker. Bypass the line voltage switch to
provide uninterrupted power to the fixtures
and make sure the connection is properly
insulated before installing the wireless switch.
Installation of Back Housing onto Junction Box
Installation Guide
2
123
45
Disconnect power to
the junction box
Remove the junction box
cover plate
For proper installation into
a dual gang junction box, the
tabs between adjacent back
housings must be removed.
Carefully observe the correct
orientation (the UP arrow
should be in the upper right
corner on each back housing).
After double checking the
product orientation, break off
the necessary tabs using pliers.
Uninstall existing wall
switches from the junction
box.
DOUBLE CHECK PRODUCT ORIENTATION BEFORE BREAKING OFF TABS.
The wall dimmer will only install into the back housing in one orientation.
Break off tabs only after the correct product orientation has been confirmed.
6Install the back housing(s)
of the wall dimmer(s) into
the wall box.
Daintree® Wireless Controls
Wireless Scene Switch(WWD2-4IW)
Terminate wires (previously
connected to wall switch)
with wire nuts.
Installation Guide
3
Installation of Device into Back Housing
Insert the back housing piece
into the junction box and
secure with two screws.
To reset the network of the device,
remove the faceplate from the
device. Then press and hold the
reset button for 5 seconds. Install
the faceplate back onto the device.
Press either dimming up or down
button to enter the pairing mode
to join the device to a network.
Separate the battery cover
from the device. Pull the
plastic insulation strip out
of the battery compartment.
Put the battery cover back
on the device.
Network Reset
123
Install the main body of the
device into the back housing.
Install the faceplate onto the
device. Note: Device supports
the use of other standard
faceplates on the market.
45
Daintree® Wireless Controls
Wireless Scene Switch(WWD2-4IW)
Use two standard screwdriver
to remove the devices from
the back housing
Installation Guide
4
Personality Change
12
Hold the reset button and
2nd button for 5 seconds to
change the personality to
dual zone mode.
Hold the reset button and 4th
button for 5 seconds to change
the personality to scene mode.
Button Change
12
Squeeze the clips on the side
of the button module to
remove the button module
from the device.
Press the replacement button
module with the desired
printing onto the device.
3Please contact if you would
like to purchase customized
buttons.
Daintree® Wireless Controls
Wireless Scene Switch(WWD2-4IW)
Battery Replacement
Installation Guide
5
Product Dimensions
123
45
The device's LED flashing
on for 2 seconds every 30
seconds indicates that the
batteries need to be replaced.
Remove the device from
the back housing.
Install the main body of
the device into the back
housing.
Install the faceplate onto
the device. The device
will rejoin its network
automatically.
Separate the battery cover
from the device. Replace
the batteries with AAA
batteries. All batteries need
to be replaced at the same
time.
Daintree® Wireless Controls
Wireless Scene Switch(WWD2-4IW)
Installation Guide
6
Product Operation
Button Functionality
LED Indicator
Forth Button
Short press
Double short press
Hold
Rapid flash (12 times per second)
for up to 30 seconds
Solid ON for 10 seconds
Flashes once (100ms duration)
Flashes ON 2 seconds every
30 seconds
Device is trying to join a ZigBee network
Device successfully joined a ZigBee network
Device has been activated while in the network
Batteries need to be replaced
Device has entered dual zone personality mode.
Device has entered four scene personality mode.
First Button
Short press
Double short press
Hold
Second Button
Short press
Double short press
Hold
Third Button
Short press
Double short press
Hold
Flashes twice (100ms duration)
Flashes four times (100ms duration)
Daintree® Wireless Controls
Wireless Scene Switch(WWD2-4IW)
Dual Zone Personality Four Scene Personality
Zone 1 lights ON at previous level
Zone 1 lights ON at 100% output
Turn Zone 1 ON and dim up
Zone 2 lights ON at previous level
Zone 2 lights ON at 100% output
Turn Zone 2 ON and dim up
Zone 1 lights OFF
Zone 1 lights ON at minimum dimming level
Turn Zone 1 ON and dim down or dim down
if lights are already ON
Zone 2 lights OFF
Zone 2 lights ON at minimum dimming level
Turn Zone 2 ON and dim down or dim down
if lights are already ON
SCENE 1 turns ON
SCENE 2 turns ON
SCENE 3 turns ON
SCENE 4 turns ON
Installation Guide
7
Technical Data
SKU DESCRIPTION ARTICLE NO.
WWD2-4IW
Operating Control
E486320
114mm H x 70mm W x 36mm D
130g
(4) AAA1.5V battery
5 years (normal operation)
-10°C to 40°C (Indoor Use Only)
Network join status, button triggered
Mounts into junction box
5 years
Operating Control
Independently Mounted
93141338
Product Specifications
Product CertificationsProduct Availablity
Daintree Wireless Controls Wall
Dimmer, In Wall, 4 Button, Battery
FCC ID: 2AS3F-WWD2IW
IC: 25008-WWD2IW
Dimensions
Weight
Power Supply
Battery Life
Operating Environment
Status Indicator
Mounting
Warranty
Purpose of Control
Construction of Control
Type 1 Action
Pollution Degree 2
Daintree® Wireless Controls
Wireless Scene Switch(WWD2-4IW)
www.gecurrent.com
© 2021 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the
General Electric Company and are used under license. Information provided is subject to change without
notice. All values are design or typical values when measured under laboratory conditions.
DT043-Daintree-WWD2-4IW-Wall-Dimmer-Installation-Guide
Installation Guide
Supplier’s Address (USA): Cleveland, Ohio
Supplier’s Phone: 1-866-855-8629
Supplier’s Name: Current Lighting Solutions, LLC
Product Name: Wireless Wall Dimmer
Model No: WWD2-4IW
Supplier’s Website: www.gecurrent.com
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences
et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
Daintree® Wireless Controls
Wireless Scene Switch(WWD2-4IW)
FCC RF Exposure Statement: Specific Absorption Rate (SAR) is a measure of the rate of RF (radiofrequency) energy
absorption by the body from the source being measured. This equipment has been found to be exempt from the RF
Exposure SAR Evaluation when the device is installed such that a person's head will, in normal conditions, be 10mm
away from the transmitter and antenna of the device.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Daintree WWD2-4IW Guide d'installation

Taper
Guide d'installation

dans d''autres langues