SloanLED 701666 Guide d'installation

Taper
Guide d'installation
Universal Dimming Controller
Installation Guide for 701666
PAGE 1 OF 2
50 60
70
80
90
1000
10
20
30
40
Tools required: 0.5" (12.7 mm) wrench,
0.125" (3.2 mm) at screw driver, Universal
Dimming Controller (P/N 701666).
1.
Remove knob from Universal Dimming Controller
using 0.125" (3.2 mm) at screw driver. Remove
0.5" (12.7 mm) nut and washer using wrench.
3. Drill a 0.375" (9.5 mm) hole in desired
mounting position.
Suggested
panel hole
size: 0.375"
(9.5 mm)
7. Align knob to zero (0) mark. Tighten knob.
50 60
70
80
90
1000
10
20
30
40
0100
External Mounting Instruction
5.
Ensure correct orientation of Universal Dimming
Controller.
Distance A is longer than Distance B
Ensure A side is pointing up during installation
Ensure wire extends to the left when seen
from inside of application
Wire
direction
Inside application
A
B
6.
Secure Universal Dimming Controller and dial
using washer and nut. Ensure potentiometer is
fully turned counterclockwise (OFF position).
50 60
70
80
90
1000
10
20
30
40
4.
Installation order:
Install Universal
Dimming Controller on to face plate.
#5 Knob
#4 Nut
#3
Washer
#1
Dial
#2
#2
#4
#5#1
#3
SloanLED Headquarters
5725 Olivas Park Drive, Ventura, CA, USA
888.747.4LED (888.747.4533) • info@SloanLED.com
SloanLED.com
SloanLED Europe b.v.
Argonstraat 110, 2718 SN Zoetermeer, NL
+31 88 12 44 900 • europe@SloanLED.com
P/N 402972 Rev B 2021-11-03
Customer service and technical support
Universal Dimming Controller
Installation Guide for 701666
PAGE 2 OF 2
Electrical Connection
Suggested dimmable
power supply list:
701507- 60C3D
701895-60S1D
701895-24S2D
7018 9 5 -10 0 L1D
NOTE: 12 V circuit must be
limited to 5 A (60 W) or less.
24 V circuit must be limited
to 4 A (96 W) or less.
For North American
installation, a power supply
that meets NEC Class 2
specications is required.
Maximum number of power
supplies: Ten (10).
Troubleshooting:
If product is not functioning properly, ensure that:
Primary voltage is 120 - 277 V
Secondary voltage:
701507-60C3D: 12 VDC
701895-60S1D: 24 VDC
701895-24S2D: 24 VDC
701895-100L1D: 24 VDC
Output current:
701507-60C3D: 5 A or less
701895-60S1D: 2.5 A or less
701895-24S2D & 701895-100L1D: 4 A or less
Power supply should not be overloaded (see latest power supply chart)
No shorts in secondary wiring
All secondary connections are RED-to-RED (+), BLACK-to-BLACK (-), PURPLE-to-PURPLE (DIM+), and GRAY/PINK/YELLOW-to-GRAY (DIM-)
No loose wires in Universal Dimming Controller terminals
Suggested power supplies
Part Number
Retrot
certied
Input Output
Nominal
Input Voltage
Input
Current
Power
Output
Output
Current
701507- 60C3D
120-277 V 0.8 A 60 W 5.0 A
701895-60S1D
120-277 V 0.8 A 60 W 2.5 A
701895-24S2D
120-277 V 1.2 A 100 W 4.0 A
70 18 9 5 -1 0 0 L1D
120-277 V 0.95 A 100 W 4.1 A
WARNING: Check Polarity – All connections must be
RED-TO-RED (+) and BLACK-TO-BLACK (-). Reverse
polarity connections may damage the LEDs and will
void product warranty. AVERTISSEMENT: Vériez la
polarité - Toutes les connexions doivent être ROUGE
À ROUGE (+) et NOIR À NOIR (-). Les connexions à
polarité inversée peuvent endommager les LED et
annuler la garantie du produit.
WARNING: Have a licensed electrician
make all primary connections.
AVERTISSEMENT: demandez à un
électricien agé d'effectuer toutes
les connexions principales.
50 60
70
80
90
1000
10
20
30
40
SloanLED Power Supply
SloanLED Power Supply
Four (4) wires: RED (+) & BLACK (-)
PURPLE (DIM+) & GRAY/PINK/YELLOW (DIM-)
LED product
LED product
701666 Universal
Dimming Controller
PURPLE (DIM+)
& PINK (DIM-)
20 AWG wire
PURPLE (DIM+)
& GRAY/PINK/YELLOW (DIM-)
Connection:
Connect SloanLED power supply and Universal
Dimming Controller: PURPLE-to-PURPLE (DIM+);
GRAY/PINK/YELLOW-to-GRAY
(DIM-)
Connect SloanLED power supply and LED
product: RED (+) to RED; BLACK (-) to BLACK
Connect SloanLED power supply to 120-277 VAC
  • Page 1 1
  • Page 2 2

SloanLED 701666 Guide d'installation

Taper
Guide d'installation

dans d''autres langues