HCS RC426A Mode d'emploi

HCS
Marque
HCS
Modèle
RC426A
Taper
Mode d'emploi
User guide for Remote Control RC4262001/01R
The remote control has been programmed to control your set-top box and can be programmed
to control your TV.
Installing Batteries
The remote requires 2xAAA batteries. A diagram inside the battery compartment of the remote
indicates proper placement of the batteries. When batteries are properly installed, the light on
the remote blinks each time a key is pressed
Know your Remote
The diagram below describes each key on your remote control. Functions may vary between
different services. Refer to the user guide for your set-top box for descriptions of specific
functions.
STB IR key code table
STB RF key code table
Product Introduction
1) This RCU is transmitting IR and RF. There is a simple set up feature for TV/Home Theatre
device.
2) The RCU can be set-up to control a RF or an IR STB (mutually exclusive).
3) The RF platform is BLE, using HOGP as the top layer.
Before the RCU can control the STB, the RCU must pair with the STB first.
4) The IR protocol to control the STB is NEC. When RCU is not connected to any STB via BLE,
MCU use IR to control STB.
Set STB Control Medium
1) Set to RF Mode:
Press <<OK+VOL->> simultaneously for 3 seconds;
2) Clear Pairing
Press << OK + VOL+>> simultaneously for 3 seconds;
3). Factory Reset:
Press <<OK+Home>> simultaneously for 3 seconds.
Voice Function
1) Press and released <Google Assistant> key to open the voice function, RCU will close the voice
function after receiving the stop command sent by the host.
2)When RCU is recording, the STB-LED is always on.
OTA
The RCU software supports upgrade via OTA (Over-The-Air).
From diagram above, the STB can transfer the RCU firmware by the BLE link.
The OTA process can be triggered by the user using the RCU or by the STB itself.
The RCU OTA IMAGE need to be downloaded into the STB itself. After the OTA is completed, the
RCU will have a new firmware.
Simple Setup
1) Simple Setup is a feature helps user to automatically set up the remote control via STB.
After being set by Simple Setup, the RCU will be able to control TV/AMP.
2) Below IR function could be configured to control TV through simple setup:
TV Power, TV Mute, TV Vol+ and TV vol-.
3) After a successful simple setup for TV, RCU will automatically set dual-function keys into TV
mode
Battery Voltage Monitor
LVD check will be triggered after a signal key is released in user mode.
1.When the LVD is detected (battery voltage<2.3V);
2. While RCU works in BLE mode, it supports Bluetooth standard service of battery level
notification. The paired host is then able to get battery level of the RCU.
Sleeping Mode
When no any activity need to do, the RC enters sleeping for power saving purpose. The sleeping
mode behaves as below:
1) All LEDs are off.
2) IR and RF communications are stopped.
3) Any key press will wake up the RC.
FCC & IC noticement
Please take attention that changes or modification not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions
suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en compromettre le fonctionnement.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

HCS RC426A Mode d'emploi

HCS
Marque
HCS
Modèle
RC426A
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Autres documents