VTech CS6629-3 Cordless Phone Manuel utilisateur

Marque: VTech

Modèle: CS6629-3 Cordless Phone

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

DS6901

DS6901

User’s manual

Scan the QR code for

support information

Go to www.vtechphones.com

(US) to register your product for

enhanced warranty support and

latest VTech product news.

Go to phones.vtechcanada.com

(Canada) for the latest VTech

product news.

Speciﬁcations are subject to change

without notice.

DS6901_CIB_V1

DS6901_CA_CIB_V1

DECT 6.0 accessory handset

for use with VTech models

DS6951/DS6951-2/DS6951-3/DS6951-4/DS6951-5

VS306-3/VS306-4/VS306-5

Important safety instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of

ﬁre, electric shock and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp

cloth for cleaning.

4. CAUTION: Do not install the telephone base at a height above 2 meters.

5. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or a

swimming pool, or in a wet basement or shower.

6. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

7. Avoid placing the telephone system in places with extreme temperature, direct sunlight, or other electrical

devices. Protect your phone from moisture, dust, corrosive liquids and fumes.

8. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To

protect them from overheating, these openings must not be blocked by placing the product on a soft surface

such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This

product should not be placed in any area where proper ventilation is not provided.

9. This product should be operated only from the type of power source indicated on the marking label. If you

are not sure of the type of power supply in your home or ofﬁce, consult your dealer or local power company.

10. Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked

on.

11. Never push objects of any kind into this product through the slots in the telephone base or handset because

they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the

product.

12. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service

facility. Opening or removing parts of the telephone base or handset other than speciﬁed access doors may

expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the

product is subsequently used.

13. Do not overload wall outlets and extension cords.

14. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the

following conditions:

• When the power supply cord or plug is damaged or frayed.

• If liquid has been spilled onto the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally by following the operating instructions. Adjust only those

controls that are covered by the operation instructions. Improper adjustment of other controls may result

in damage and often requires extensive work by an authorized technician to restore the product to

normal operation.

• If the product has been dropped and the telephone base and/or handset has been damaged.

• If the product exhibits a distinct change in performance.

15. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric

shock from lightning.

16. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances, a spark

may be created when the adapter is plugged into the power outlet, or when the handset is replaced in

its cradle. This is a common event associated with the closing of any electrical circuit. The user should not

plug the phone into a power outlet, and should not put a charged handset into the cradle, if the phone is

located in an environment containing concentrations of ﬂammable or ﬂame-supporting gases, unless there

is adequate ventilation. A spark in such an environment could create a ﬁre or explosion. Such environments

might include: medical use of oxygen without adequate ventilation; industrial gases (cleaning solvents;

gasoline vapors; etc.); a leak of natural gas; etc.

17. Only put the handset of your telephone next to your ear when it is in normal talk mode.

18. The power adapter is intended to be correctly oriented in a vertical or ﬂoor mount position. The prongs

are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

19. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily

accessible.

20. CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion

if a wrong type of battery is used for the handset. Use only the supplied rechargeable

batteries or replacement batteries (BT162342/BT262342) for the handset. Do not dispose of

batteries in a ﬁre. They may explode.

21. Use only the adapter included with this product. Incorrect adapter polarity or voltage can seriously damage

the product.

SAVE THESE INSTRUCTIONS

Battery

• Use only the batteries provided or equivalent. To order a replacement, visit our website at

www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to phones.vtechcanada.com or call

1 (800) 267-7377.

• Do not dispose of the battery in a ﬁre. Check with local waste management codes for special disposal

instructions.

• Do not open or mutilate the battery. Released electrolyte is corrosive and may cause burns or injury to the

eyes or skin. The electrolyte may be toxic if swallowed.

• Exercise care in handling batteries in order not to create a short circuit with conductive materials.

• Charge the battery provided with this product only in accordance with the instructions and limitations

speciﬁed in this manual.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless telephones):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of

the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by the U.S.

Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless telephones at least six inches from the pacemaker.

• Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it is

turned ON.

• Should use the wireless telephone at the ear opposite the pacemaker.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless

telephones.

About cordless telephones

• Privacy: The same features that make a cordless telephone convenient create some limitations. Telephone

calls are transmitted between the telephone base and the cordless handset by radio waves, so there is a

possibility that the cordless telephone conversations could be intercepted by radio receiving equipment

within range of the cordless handset. For this reason, you should not think of cordless telephone

conversations as being as private as those on corded telephones.

• Electrical power: The telephone base of this cordless telephone must be connected to a working electrical

outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made from the cordless

handset if the telephone base is unplugged, switched off or if the electrical power is interrupted.

• Potential TV interference: Some cordless telephones operate at frequencies that may cause interference

to televisions and VCRs. To minimize or prevent such interference, do not place the telephone base of

the cordless telephone near or on top of a TV or VCR. If interference is experienced, moving the cordless

telephone farther away from the TV or VCR often reduces or eliminates the interference.

• Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with

conducting material such as rings, bracelets and keys. The battery or conductor may overheat and cause

harm. Observe proper polarity between the battery and the battery charger.

• Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not burn or

puncture the battery. Like other batteries of this type, if burned or punctured, they could release caustic

material which could cause injury.

ECO mode

This power conserving technology reduces power consumption for optimal battery performance. The ECO mode

activities automatically whenever the handset is synchronized with the telephone base.

For C-UL compliance only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de blessures corporelles ou d’électrocution, suivez toujours ces

mesures préventives de base lorsque vous utilisez votre téléphone :

1. Lisez et comprenez bien toutes les instructions.

2. Observez toutes les instructions et mises en garde inscrites sur l’appareil.

3. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas de nettoyeurs liquides ni en

aérosol. N’utilisez qu’un chiffon doux et légèrement humecté.

4. ATTENTION: Ne pas installer le socle téléphonique à une hauteur supérieure à 2 mètres.

5. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier de cuisine, d’un bac de

lavage ou d’une piscine, ou dans un soussol humide ou sous la douche.

6. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil pourrait tomber et

être sérieusement endommagé.

7. Évitez d’installer le système téléphonique dans les endroits soumis à une température extrême, à la lumière

directe du soleil ou à proximité immédiate d’autres appareils électriques ou électroniques. Protégez votre

téléphone contre les sources d’humidité, la poussière, les vapeurs et les liquides corrosifs.

8. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière ou en dessous. Aﬁn

d’empêcher la surchauffe, ces ouvertures ne doivent pas être obstruées en plaçant l’appareil sur un lit, divan,

tapis ou autre surface similaires. Ne placez pas cet appareil proximité d’un élément de chauffage ni d’une

plinthe électrique. De plus, ne l’installez pas dans une unité murale ou un cabinet fermé qui ne possède

pas d’aération adéquate.

9. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les étiquettes de l’appareil.

Si vous ne connaissez pas le voltage de votre maison, consultez votre marchand ou votre fournisseur

d’électricité.

10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit sécuritaire, là où

personne ne pourra trébucher sur la ligne d’alimentation ni le cordon téléphonique modulaire.

11. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils pourraient toucher à des

points de tension dangereux ou court-circuiter des pièces, ce qui constituerait un risque d’incendie ou

d’électrocution. N’échappez pas de liquides dans l’appareil.

12. Aﬁn de réduire les risques d’électrocution, ne démontez pas l’appareil, mais apportez-le plutôt à un

centre de service qualiﬁé s’il doit être réparé. En enlevant le couvercle, vous vous exposez à des tensions

dangereuses ou autres dangers similaires. Un remontage inadéquat peut être à l’origine d’une électrocution

lors d’une utilisation ultérieure de l’appareil. Débranchez l’appareil avant de procéder au nettoyage. Utilisez

un chiffon humide et doux.

13. Ne surchargez pas les prises de courant et les rallonges.

14. Débranchez cet appareil de la prise de courant et communiquez avec le département de service à la clientèle

de VTech dans les cas suivants:

• Lorsque le cordon d’alimentation est endommagé ou écorché. • Si du liquide a été échappé dans

l’appareil.

• Si l’appareil a été exposé une source d’humidité telle que la pluie ou l’eau.

• Si le produit ne fonctionne pas normalement en respectant les instructions de fonctionnement. Réglez

uniquement les commandes indiquées dans le les instructions de fonctionnement. Les réglages

incorrects des autres commandes pourraient provoquer un dommage qui pourrait exiger un travail

exhaustif de la part d’un technicien autorisé aﬁn de rétablir le fonctionnement normal de l’appareil.

• Si le produit a été échappé et que le socle et/ ou le combiné a été endommagé.

• Si le produit afﬁche une nette diminution de sa performance.

15. Évitez d’utiliser un téléphone (autre qu’un sans ﬁl) pendant un orage. Les éclairs peuvent être à l’origine

d’une électrocution.

16. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite. En certaines circonstances,

une ﬂammèche pourrait être provoquée lorsque l’adaptateur est branché à une prise de courant, ou

lorsque le combiné est déposé sur le socle. Ceci est un événement commun associé à la fermeture d’un

circuit électrique. L’utilisateur ne devrait pas brancher le téléphone à une prise de courant, et ne devrait pas

déposer le combiné chargé sur le socle, si le téléphone se trouve à proximité d’un endroit comportant des

concentrations de gaz inﬂammables, moins que la ventilation soit adéquate. Une ﬂammèche dans un tel

endroit pourrait provoquer un incendie ou une explosion. De tels environnements peuvent comprendre:

des endroits où l’on utilise de l’oxygène médical sans ventilation adéquate; des gaz industriels (dissolvants de

nettoyage, des vapeurs d’essence, etc.); une fuite de gaz naturel, etc.

17. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode de conversation.

18. Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au sol. Les broches ne

sont pas conçues pour maintenir l’adaptateur en place si celui-ci est barnché dans une prise au plafond ou

sous une table/ armoire.

19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le socle de prise de courant doit etre installe a

proximite du materiel et doit etre aisement accessible.

20. MISE EN GARDE: Il peut y avoir un risque d’explosion si vous utilisez le mauvais type de piles

pour le téléphone. N’utilisez que les piles rechargeable inclus ou les piles de rechange

(BT162342/BT262342). N’incinérez pas les piles. Celles-ci risqueraient d’exploser.

21. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur dont la polarité ou la tension

serait inadéquate risque d’endommager sérieusement le produit et mettre votre sécurité en péril.

CONSERVEZ CES INSTRUCTIONS

Pile

• N’utilisez que la pile incluse ou l’équivalent. Pour commander une pile de recharge, visitez notre site Web au

www.vtechphones.com ou composez le 800-595-9511.

• Au Canada, visitez le phones. phones.vtechcanada.com ou composez le 800-267-7377.

• Ne jetez pas la pile au feu. Vériﬁez les instructions spéciﬁques de mise aux rebus auprès des autorités locales.

• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif et pourrait causer des

brûlures ou des blessures aux yeux ou à la peau. L’électrolyte est toxique si avalé.

• Soyez prudents lorsque vous manipulez les piles aﬁn d’éviter les courts-circuits provoqués par des matériaux

conducteurs.

• Rechargez la pile incluse avec cet appareil, selon les instructions et limites spéciﬁées dans ce guide

d’utilisation.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans ﬁl):

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une ﬁrme de recherche indépendante, a mené une

évaluation pluridisciplinaire des interférences entre les téléphones sans ﬁl portatifs et les stimulateurs cardiaques

implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des États-Unis, la ﬁrme

WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Ils doivent tenir le téléphone sans ﬁl à une distance d’au moins six pouces du stimulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement sur le stimulateur cardiaque, tel que dans une

poche de chemise, lorsque celui-ci est en marche.

• Ils doivent utiliser le téléphone sans ﬁl en l’appuyant sur l’oreille qui se trouve dans la direction opposée

au stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de risque pour les détenteurs de simulateurs cardiaques

causés par les gens qui utilisent un téléphone sans ﬁl à proximité de ceux-ci.

À propos des téléphones sans ﬁl

• Alimentation électrique: Les mêmes caractéristiques qui constituent des avantages pour les téléphones sans

ﬁl afﬁchent également des restrictions. Les appels téléphoniques sont transmis entre le combiné sans ﬁl et

le socle par le biais d’ondes radio ; il y a donc la possibilité que vos conversations téléphoniques sans ﬁl

soient interceptées par des équipements de réception radio se trouvant dans la portée du combiné sans

ﬁl. Pour cette raison, vous ne devez pas percevoir les communications téléphoniques sans ﬁl comme étant

aussi conﬁdentielles.

• Alimentation électrique: Le socle de ce téléphone sans ﬁl doit être branché à une prise électrique

fonctionnelle. La prise électrique ne doit pas être contrôlée par un interrupteur mural. Les appels ne pourront

pas être effectués du combiné sans ﬁl si le socle est débranché ou mis hors tension ou si le courant est coupé.

• Possibilité d’interférences aux téléviseurs: Certains téléphones sans ﬁl fonctionnent sur des fréquences

pouvant causer des interférences aux téléviseurs et aux magnétoscopes. Pour réduire ou prévenir de telles

interférences, ne placez pas le socle du téléphone sans ﬁl près ou sur un téléviseur ou magnétoscope. S’il y a

présence de parasites, il est conseillé d’éloigner le téléphone sans ﬁl du téléviseur ou du magnétoscope aﬁn

de réduire possiblement les interférences.

• Piles rechargeables: Manipulez les piles avec soin aﬁn de ne pas les court-circuiter avec des bagues, bracelets

ou clés. Les piles ou le conducteur peut surchauffer et causer des blessures. Respectez la polarité adéquate

entre la pile et le chargeur.

• Les bloc-piles rechargeables à l’hydrure métallique de nickel: Jetez ces blocs-piles de manière écologique

et sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les autres piles de ce type, elles pourraient

dégager une matière toxique qui peut causer des blessures corporelles si elles sont brûlées ou percées.

The RBRC seal

The RBRC seal on the nickel-metal hydride battery indicates that VTech Communications, Inc. is

voluntarily participating in an industry program to collect and recycle these batteries at the end of

their useful lives, when taken out of service within the United States and Canada.

The program provides a convenient alternative to placing used nickel-metal hydride batteries into

the trash or municipal waste, which may be illegal in your area.

VTech’s participation makes it easy for you to drop off the spent battery at local retailers

participating in the RBRC® program or at authorized

VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Ni-MH battery recycling and

disposal bans/restrictions in your area.

VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural

resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

FCC, ACTA and IC regulations

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device under

Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide

reasonable protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations to this equipment not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation. Privacy of communications may not be ensured when using this telephone.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be

safely absorbed by a user or bystander

according to the intended usage of the product. This product has been tested and found to comply with the FCC

criteria. The handset may be safely held

against the ear of the user. The telephone base shall be installed and used such that parts of the user’s body

other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian requirement: CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the

Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains,

among other things, a product identiﬁer in the format US:AAAEQ##TXXXX. This identiﬁer must be provided to your

telephone service provider upon request.

The plug and jack used to connect this equipment to premises wiring and the telephone network must comply

with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and

modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also

compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See

the installation instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone

line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters

following the US: in the product identiﬁer (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all

RENs should be ﬁve (5.0) or less. For more information, please contact your telephone service provider.

This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to

your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have

questions about what will disable alarm equipment, consult your telephone service provider or a qualiﬁed installer.

If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been

corrected. Replacement to this telephone equipment can only be made by the manufacturer or its authorized

agents. For replacement procedures, follow the instructions outlined under the “Limited warranty”.

If this equipment is causing harm to the telephone network, the telephone service provider may temporarily

discontinue your telephone service. The telephone service provider is required to notify you before interrupting

service. If advance notice is not practical, you will be notiﬁed as soon as possible. You will be given the opportunity

to correct the problem and the telephone service provider is required to inform you of your right to ﬁle a complaint

with the FCC. Your telephone service provider may make

changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this

product. The telephone service provider is required to notify you if such changes are planned.

If this product is equipped with a corded or cordless handset, it is hearing aid compatible. If this product has

memory dialing locations, you may

choose to store emergency telephone numbers (e.g., police, ﬁre, medical) in these locations. If you do store or test

emergency numbers, please:

Remain on the line and brieﬂy explain the reason for the call before hanging up.

Perform such activities in off-peak hours, such as early morning or late evening.

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference

that may cause undesired operation. Privacy of communications may not be ensured when using this telephone.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the Industry Canada technical

speciﬁcations were met.

The Ringer Equivalence Number (REN) for this terminal equipment is 1.0. The REN is an indication of the maximum

number of devices allowed to be connected to a telephone interface. The termination on an interface may consist

of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does

not exceed ﬁve.

This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations.

California Energy Commission Battery charging testing instructions

This telephone is set up to comply with the energy-conserving standards right out of the box. These instructions are

intended for California Energy Commission (CEC) compliance testing only. When the CEC battery charging testing

mode is activated, all telephone functions, except battery charging, will be disabled.

To activate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power outlet. Make sure all handsets are plugged with

charged batteries before proceeding.

2. While you press and hold /FIND HS, plug the telephone base power adapter back to the power outlet.

3. After about 20 seconds, when the HOME light starts ﬂashing, release /FIND HS and then press it again within

two seconds. You hear a conﬁrmation tone. The HOME light turns on and all handsets display To register HS...

see manual alternately. Allow up to one minute for the process to complete.

If the phone fails to enter this mode, repeat all the steps mentioned above. The telephone base will be powered up

as normal if you fail to press /FIND HS within two seconds in Step 3.

To deactivate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power outlet, and then plug it back in. Then the

telephone base is powered up as normal.

2. Put the handsets on the telephone base cradle to begin registration.

3. The handset shows Registering... If the registration is successful, the handset screen displays Registered and

beeps. The handset is registered with the telephone base.

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”)

that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and

workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance

with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased

and used in the United States of America and Canada.

What will VTech do if the Product is not free from defects in materials and workmanship

during the limited warranty period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service representative will replace at VTech’s option, without

charge, a Materially Defective Product. If we replace the Product, we may use new or refurbished replacement

parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar

design. We will retain defective parts, modules, or equipment. Replacement of the Product, at VTech’s option, is

your exclusive remedy. VTech will return the replacement Products to you in working condition. You should expect

the replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech replaces

a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the

replacement Product for a period of either (a) 90 days from the date the replacement Product is shipped to you or

(b) the time remaining on the original one-year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper

installation, abnormal operation or handling, neglect, inundation, ﬁre, water or other liquid intrusion.

2. Product that has been subjected to contact with liquid, water, rain, extreme humidity or heavy perspiration,

sand, dirt or the like; but then only to the extent the damage was not caused by incorrectly securing the

waterproof handset’s protective elements, for example, failing to properly close a seal), or such protective

elements are damaged or missing (e.g. a cracked battery door), or subjecting a Product to conditions beyond

its stated speciﬁcations or limits (e.g. 30 minutes in 1 meter of fresh water).

3. Product that has been damaged due to repair, alteration or modiﬁcation by anyone other than an authorized

service representative of VTech;

4. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or

cable or antenna systems;

5. Product to the extent that the problem is caused by use with non-VTech accessories;

6. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been

removed, altered or rendered illegible;

7. Product purchased, used, serviced, or shipped for repair from outside the United States of America or

Canada, or used for commercial or institutional purposes (including but not limited to Products used for

rental purposes);

8. Product returned without a valid proof of purchase (see item 2 below); or

9. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside

the unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511.

To obtain warranty service in Canada, go to phones.vtechcanada.com or dial 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features

may save you a service call.

Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and

are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location.

VTech will return replaced Product under this limited warranty. Transportation, delivery or handling charges are

prepaid.

VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this

limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and

will request that you authorize the cost of replacement prior to any further replacement activity. You must pay for

the cost of replacement and return shipping costs for the replacement of Products that are not covered by this

limited warranty.

What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech service location along

with a description of the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and

the date of purchase or receipt; and

3. Provide your name, complete and correct mailing address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written

or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty

exclusively describes all of VTech’s responsibilities regarding the Product. There are no other express warranties. No

one is authorized to make modiﬁcations to this limited warranty and you should not rely on any such modiﬁcation.

State/Provincial Law Rights: This warranty gives you speciﬁc legal rights, and you may also have other rights, which

vary from state to state or province to province.

Limitations: Implied warranties, including those of ﬁtness for a particular purpose and merchantability (an unwritten

warranty that the Product is ﬁt for ordinary use) are limited to one year from the date of purchase. Some states/

provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply

to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages

(including, but not limited to lost proﬁts or revenue, inability to use the Product or other associated equipment,

the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/

provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation

or exclusion may not apply to you.

Please retain your original sales receipt as proof of purchase.

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use

of this user’s manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or claims by

third parties that may arise through the use of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste 555, Tigard, OR 97223, United States

Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada

Technical Speciﬁcations

Frequency control Crystal controlled PLL synthesizer

Transmit frequency Handset: 1921.536-1928.448 MHz

Channels DECT channel: 5

Nominal effective

range Maximum power allowed by FCC and IC. Actual operating range may vary

according to environmental conditions at the time of use.

Power requirement Handset: 2.4 V DC, AAA×2, Ni-MH battery | Charger: 6V DC @ 400mA

Memory Phonebook: 1000 memory locations; up to 30 digits and 15 characters

Caller ID log: 50 memory locations; up to 24 digits and 15 characters

Call block: 1000 entries

What’s in the box

Your telephone package contains the following items.

Save your sales receipt and original packaging in the

event warranty service is necessary.

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR2105

User’s manual

Install the battery

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR2105

THIS SIDE UP

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1939

Connect the charger

Charge the battery

Battery

indicators

Battery status Action

• The screen is

blank, or shows

Put in charger

and ﬂashes.

• The battery has

no charge or

very little charge.

The handset

cannot be used.

• Charge

without

interruption

(at least 30

minutes).

• The screen

shows Low

battery and

ﬂashes.

• The battery has

enough charge

to be used for a

short time.

• Charge

without

interruption

(at least 30

minutes).

• The screen

shows

HANDSET X.

• The battery is

charged.

• To keep

the battery

charged,

place it in

the handset

charger when

not in use.

Display icons overview

• The handset battery is low and

needs charging.

• The handset battery is charging.

• The handset battery is fully

charged.

ECO • The ECO mode activates

automatically to reduce power

consumption when the handset is

within range of the telephone base.

• New voicemail received from your

telephone service provider.

• Displays when Home line is in use.

• Bluetooth device is paired and

active.

• Bluetooth device / Cell line is in use.

NEW

• There are new caller ID log entries

ANS ON • Answering system is on.

10:30PM • Time with AM and PM.

• Handset ringer is off.

10/16

MSG # • Handset displays the current

message number being played

and the total number of new/old

messages recorded.

Handset overview

See manual of DS6951/DS6951-2/DS6951-3/DS6951-4/

DS6951-5/VS306-3/VS306-4/VS306-5 for details.

LCD language setting

If you accidentally set the LCD language to Spanish or

French, press MENU and then enter 364# to change the

handset LCD language back to English while the handset

is not in use.

12 hrs

Before use

Add and register a handset

You can add new DS6901 handsets (purchased separately)

to your DS6951/DS6951-2/DS6951-3/DS6951-4/DS6951-

5/VS306-3/VS306-4/VS306-5 telephone system. Your

telephone system supports a maximum of 5 handsets.

Each handset must be registered with the telephone

base before use. When ﬁrst purchased, each expansion

handset displays To register HS... and ... see manual

alternately.

NOTES

• Charge the new handset without interruption for at

least 30 minutes before registering it to the telephone

base.

• You cannot register a handset if any other system

handset is in use.

1. Put the handset you wish to register on the telephone

base cradle.

2. The handset shows Registering.... If the registration

is successful, the handset screen displays Registered

and beeps. The handset is now registered with the

telephone base.

If registration fails, Registration failed appears on the

handset screen. The handset shows To register HS... and

see manual alternately and the telephone base returns

to idle mode. This may take up to ﬁve minutes to occur.

Please start again from Step 1.

Deregister handsets

If you want to replace a handset or reassign the

designated handset number of a registered handset, you

must deregister all the handsets and then individually

If you want to register a handset to another telephone

base, you must deregister all handsets, and then register

each handset individually to the desired telephone base.

Deregister all handsets from the

telephone base

1. Press and hold /FIND HS on the telephone base

for about 10 seconds. The telephone base shows

Deregister all devices?. Release /FIND HS.

2. Immediately press /FIND HS again. The telephone

base shows Deregistered all devices, and you hear a

conﬁrmation tone.

3. All handsets display To register HS... and see manual

alternately when the deregistration process completes.

The deregistration process takes about 10 seconds.

NOTES

• If the deregistration process fails, you may need to

reset the system and try again. To reset, unplug the

power from the telephone base and plug it back in.

• You cannot deregister the handsets if any other system

handset is in use.

• Even if the battery is depleted, you can still deregister

the handsets by following the steps. After the handset

is charged for at least 10 minutes, the screen shows To

Operating range

This cordless telephone operates with the maximum

power allowed by the Federal Communications

Commission (FCC). Even so, this handset and telephone

base can communicate over only a certain distance which

can vary with the locations of the telephone base and

handset, the weather, and the layout of your home or

ofﬁce.

When the handset is out of range, the handset displays

Out of range or no pwr at base.

If there is a call while the handset is out of range, it may not

ring, or if it does ring, the call may not connect well when

you press . Move closer to the telephone base, and

then press to answer the call. If the handset moves

out of range during a telephone conversation, there may

be interference. To improve reception, move closer to the

telephone base.

Need help?

For operations and guides to help you using your

telephone, and for latest information and supports, go

and check the online help topics and online FAQs.

Use your smartphone or mobile device to access our

online help.

• Go to https://help.vtechphones.com/ds6901;

• Scan the QR code on the right.

Launch the camera app or QR code

scanner app on your smartphone or

tablet. Hold the device’s camera up

to the QR code and frame it. Tap the

notiﬁcation to trigger the redirection

of the online help.

If the QR code is not clearly displayed,

adjust your camera’s focus by moving

your device closer or further away until

it is clear.

You can also call our Customer Support

at 1 (800) 595-9511 [in US] or

1 (800) 267-7377 [in Canada] for help.

DS6951/VS306 base

Do not place the

handset in the

charger.

VTech CS6629-3 Cordless Phone Manuel utilisateur

Marque: VTech

Modèle: CS6629-3 Cordless Phone

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

DS6901

Télécharger le PDF

rapport

dans d''autres langues

English: VTech CS6629-3 Cordless Phone User manual

VTech CS6629-3 Cordless Phone Manuel utilisateur

Ce manuel convient également à

VTech CS6629-3 Cordless Phone Manuel utilisateur

dans d''autres langues

Documents connexes