VTech IS8129 Manuel utilisateur

Marque: VTech

Modèle: IS8129

Catégorie: Téléphones

Taper: Manuel utilisateur

Quick start guide

What’s in the box

Connect the telephone base Connect the charger

Charge the battery

Speciﬁcations are subject to change without notice.

HS59SCB2 DCX81

Telephones identiﬁed with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and

cochlear implants. The TIA-1083 Compliant Logo is a trademark of

the Telecommunications Industry Association. Used under license.

Compatible with

Hearing

d T-Coil

TIA-1083

The ENERGY STAR® program (www.energystar.gov) recognizes and

encourages the use of products that save energy and help protect our

environment. We are proud to mark this product with the ENERGY

STAR® label indicating it meets the latest energy efﬁciency guidelines.

12 hrs

Technical speciﬁcations

Frequency control Crystal controlled PLL synthesizer

Transmit frequency Handset: 1921.536-1928.448 MHz

Telephone base: 1921.536-1928.448 MHz

Channels 5

Nominal effective

range

Maximum power allowed by FCC and IC.

Actual operating range may vary according to

environmental conditions at the time of use.

Power requirement Handset: 2.4V Ni-MH battery

Telephone base: 6V DC @ 600mA

Charger: 6V DC @ 400mA

Memory Phonebook: 1000 memory locations;

up to 30 digits and 15 characters

Caller ID log: 50 memory locations;

up to 24 digits and 15 characters

Call block: 1000 entries

If you subscribe to digital subscriber

line (DSL) high-speed Internet service

through your telephone line, make

sure you connect a DSL ﬁlter (not

included) to the telephone wall jack.

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1939

Connect and install

Quick

start

guide

Introducing

Smart call

blocker

Display

Handset:

The handset battery is low and needs charging.

The handset battery is charging.

The handset battery is fully charged.

Handset or telephone base ringer is off.

New voicemail received from your telephone service

provider.

NEW

New caller ID log entry.

Displays when Home line is in use.

Bluetooth device(s) is/are paired and active.

Bluetooth device / Cell line is in use.

ANS ON Answering system is on.

10/16

MSG # Handset displays the current message number being played

and the total number of new/old messages recorded.

MSG#

0Telephone base message counter displays the total

number of messages.

ECO The ECO mode activates automatically to reduce power

consumption when the handset is within range of the

telephone base.

To use a Bluetooth enabled cellular phone or headset with your telephone, you must ﬁrst pair and connect your Bluetooth cellular phone or

headset with the telephone base. Before you begin, make sure that you have cellular coverage and your Bluetooth enabled cell phone or

headset is not connected to any other Bluetooth device.

Add a Bluetooth cell phone Add a Bluetooth headset

The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use

of such marks by VTech Holdings Limited is under license. VTech Holdings Limited

is a member of Bluetooth SIG, Inc. Other trademarks and trade names are those of

their respective owners.

Telephone base:

Setup

After you install your telephone or power returns following

a power outage and battery depletion, the handset and

telephone base will prompt you to set the date and time, and

to conﬁgure the Smart call blocker* and answering system

through voice guide.

Date and time

Follow the steps below to set the date and time.

For example, if the date is 25 July, 2022, and the time is 12:05 PM:

Voice guide for Smart call blocker / Answering system

After setting the date and time, the telephone base will prompt

if you want to set Smart call blocker, and the answering system.

For more details, see Use voice guide to set Smart call blocker in

the Introducing Smart call blocker leaﬂet and Use voice guide

to set Answsering system in the online help topics.

When the telephone base prompts you to set up the Smart call

blocker via voice guide:

When the handset

and telephone

base prompt you

to set the date and

time:

Date: MM/DD/YY

ECO

Date: 07/25/22

ECO

Press SELECT.

Time: 12:05 PM

ECO

Press SELECT.

Setup your answering system by

inputting the designated numbers

as instructed in the voice guide.

Voice guide to

set up Ans sys?

Press MENU on the

telephone base to start

voice guide setup.

“This voice guide will assist

you with the basic setup of

your answering system“

“Hello! This voice guide will

assist you with the basic

setup of Smart call blocker“

Voice guide set

Smart call blk?

Press MENU on the

telephone base to start

voice guide setup.

Setup your Smart call blocker by

inputting the designated numbers

as instructed in the voice guide.

Make a home call

Operate

End a home call

For operations and guides to help you using your telephone system,

and for latest information and supports, go and check the online help

topics and online FAQs.

Use your smartphone or mobile device to access our online help.

• Go to https://help.vtechphones.com/IS8129 or https://

phones.vtechcanada.com/en/support/general/

manuals?model=IS8129; OR

• Scan the QR code on the right. Launch the camera app or QR

Volume

Handset: Telephone base:

End a cell call

Handset: Telephone base:

Make a cell call

Answer a home call

Telephone base:

Handset:

- OR -

Answer a cell call

Telephone base:

Handset:

- OR -

Handset:

- OR -

Telephone base:

- OR -

Handset: Telephone base:

- OR -

code scanner app on your smartphone or tablet. Hold the device’s

camera up to the QR code and frame it.

Tap the notiﬁcation to trigger the redirection of the online help.

If the QR code is not clearly displayed, adjust your camera’s focus by

moving your device closer or further away

until it is clear. You can also call our Customer

Support at

1 (800) 595-9511 [in US] or

1 (800) 267-7377 [in Canada] for help.

Need help?

Date: 07/2?/--

ECO

Enter the date.

Time: HH:MM -

ECO

Enter the time.

Enter the phone number.

Enter the phone number, and then press

SELECT.

Press

Bluetooth

A d din g c ell...

4Turn on the Bluetooth

feature of your cell phone.

1Press MENU on the

telephone base.

BASE

8 /17 5:3 2 a m

MSG#

Intercom

>Bluetooth

2Press q/p to scroll

to Bluetooth, then

press SELECT.

BLUETOOTH

> A d d c ellula r

3Press SELECT to

select Add cellular.

Once your cell phone

ﬁnds your telephone

(VTech DECT 6.0), press

the appropriate key

on your cell phone to

continue the pairing

process.

Search headset...

4Set your headset to

discoverable mode.

Bluetooth headset

2 added.

1Press MENU on the

telephone base.

BASE

8 /17 5:3 2 a m

MSG#

Intercom

>Bluetooth

2Press q/p to scroll

to Bluetooth, then

press SELECT.

BLUETOOTH

>Add headset

3Press q/p to scroll

to Add headset,

then press SELECT.

Refer to the user’s

manual of your

Bluetooth headset on

how to pair it to your

IS8129 telephone.

When using your telephone equipment, basic

safety precautions should always be followed to

reduce the risk of ﬁre, electric shock and injury,

including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked

on the product.

3. Unplug this product from the wall outlet

before cleaning. Do not use liquid or

aerosol cleaners. Use a damp cloth for

cleaning.

4. CAUTION: Do not install the telephone

base at a height above 2 meters.

5. Do not use this product near water such as

near a bath tub, wash bowl, kitchen sink,

laundry tub or a swimming pool, or in a wet

basement or shower.

6. Do not place this product on an unstable

table, shelf, stand or other unstable

surfaces.

7. Avoid placing the telephone system in

places with extreme temperature, direct

sunlight, or other electrical devices. Protect

your phone from moisture, dust, corrosive

liquids and fumes.

8. Slots and openings in the back or bottom

of the telephone base and handset are

provided for ventilation. To protect them

from overheating, these openings must not

be blocked by placing the product on a

soft surface such as a bed, sofa or rug. This

product should never be placed near or

over a radiator or heat register. This product

should not be placed in any area where

proper ventilation is not provided.

9. This product should be operated only

from the type of power source indicated

on the marking label. If you are not sure of

the type of power supply in your home or

ofﬁce, consult your dealer or local power

company.

10. Do not allow anything to rest on the power

cord. Do not install this product where the

cord may be walked on.

11. Never push objects of any kind into this

product through the slots in the telephone

base or handset because they may touch

dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the

product.

12. To reduce the risk of electric shock, do not

disassemble this product, but take it to

an authorized service facility. Opening or

removing parts of the telephone base or

handset other than speciﬁed access doors

may expose you to dangerous voltages

or other risks. Incorrect reassembling can

cause electric shock when the product is

subsequently used.

13. Do not overload wall outlets and extension

cords.

14. Unplug this product from the wall outlet

and refer servicing to an authorized service

facility under the following conditions:

• When the power supply cord or plug is

damaged or frayed.

• If liquid has been spilled onto the

product.

• If the product has been exposed to rain

or water.

• If the product does not operate

normally by following the operating

instructions. Adjust only those controls

that are covered by the operation

instructions. Improper adjustment of

other controls may result in damage

and often requires extensive work by

an authorized technician to restore the

product to normal operation.

• If the product has been dropped and

the telephone base and/or handset has

been damaged.

• If the product exhibits a distinct change

in performance.

15. Avoid using a telephone (other than

cordless) during an electrical storm. There

is a remote risk of electric shock from

lightning.

16. Do not use the telephone to report a

gas leak in the vicinity of the leak. Under

certain circumstances, a spark may be

created when the adapter is plugged into

the power outlet, or when the handset is

replaced in its cradle. This is a common

event associated with the closing of any

electrical circuit. The user should not plug

the phone into a power outlet, and should

not put a charged handset into the cradle,

if the phone is located in an environment

containing concentrations of ﬂammable

or ﬂame-supporting gases, unless there

is adequate ventilation. A spark in such

an environment could create a ﬁre or

explosion. Such environments might

include: medical use of oxygen without

adequate ventilation; industrial gases

(cleaning solvents; gasoline vapors; etc.); a

leak of natural gas; etc.

17. Only put the handset of your telephone

next to your ear when it is in normal talk

mode.

18. The power adapter is intended to be

correctly oriented in a vertical or ﬂoor

mount position. The prongs are not

designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or

cabinet outlet.

19. For pluggable equipment, the socket-

outlet shall be installed near the equipment

and shall be easily accessible.

Important safety instructions 20. CAUTION: Use only the

batteries indicated in this manual. There

may be a risk of explosion if a wrong type

of battery is used for the handset. Use

only the supplied rechargeable batteries

or replacement batteries (BT162342/

BT262342) for the handset. Do not dispose

of batteries in a ﬁre. They may explode.

• Do not use the battery in following

conditions:

» High or low extreme temperature

during use, storage or

transportation.

» Replacement of a battery with an

incorrect type that can defeat a

safeguard.

» Disposal of a battery into ﬁre or a

hot oven, or mechanically crushing

or cutting of a battery, that can

result in an explosion.

» Leaving a batteryin an extremely

high temperature surrounding

environment that can result in

an explosion or the leakage of

ﬂammable liquid or gas.

» A battery subjected to extremely

low air pressure that can result in

an explosion or the leakage of

ﬂammable liquid or gas.

21. Use only the adapter included with

this product. Incorrect adapter polarity

or voltage can seriously damage the

product.

22. The applied nameplate is located at the

bottom or near of the product.

SAVE THESE INSTRUCTIONS

Battery

• Use only the batteries provided or

equivalent. To order a replacement, visit

our website at www.vtechphones.com or

call 1 (800) 595-9511. In Canada, go to

phones.vtechcanada.com or call

1 (800) 267-7377.

• Do not dispose of the battery in a ﬁre. Check

with local waste management codes for

special disposal instructions.

Do not open or mutilate the battery.

Released electrolyte is corrosive and may

cause burns or injury to the eyes or skin. The

electrolyte may be toxic if swallowed.

• Exercise care in handling batteries in order

not to create a short circuit with conductive

materials.

• Charge the battery provided with this

product only in accordance with the

instructions and limitations speciﬁed in this

manual.

Precautions for users of implanted cardiac

pacemakers

Cardiac pacemakers (applies only to digital

cordless telephones):

Wireless Technology Research, LLC (WTR),

an independent research entity, led a

multidisciplinary evaluation of the interference

between portable wireless telephones and

implanted cardiac pacemakers. Supported by

the U.S. Food and Drug Administration, WTR

recommends to physicians that:

Pacemaker patients

• Should keep wireless telephones at least six

inches from the pacemaker.

• Should NOT place wireless telephones

directly over the pacemaker, such as in a

breast pocket, when it is turned ON.

• Should use the wireless telephone at the ear

opposite the pacemaker.

WTR’s evaluation did not identify any risk to

bystanders with pacemakers from other persons

using wireless telephones.

About cordless telephones

• Privacy: The same features that make a

cordless telephone convenient create some

limitations. Telephone calls are transmitted

between the telephone base and the

cordless handset by radio waves, so there

is a possibility that the cordless telephone

conversations could be intercepted by

radio receiving equipment within range

of the cordless handset. For this reason,

you should not think of cordless telephone

conversations as being as private as those on

corded telephones.

• Electrical power: The telephone base of this

cordless telephone must be connected to a

working electrical outlet. The electrical outlet

should not be controlled by a wall switch.

Calls cannot be made from the cordless

handset if the telephone base is unplugged,

switched off or if the electrical power is

interrupted.

• Potential TV interference: Some cordless

telephones operate at frequencies that may

cause interference to televisions and VCRs.

To minimize or prevent such interference,

do not place the telephone base of the

cordless telephone near or on top of a TV or

VCR. If interference is experienced, moving

the cordless telephone farther away from

the TV or VCR often reduces or eliminates

the interference.

• Rechargeable batteries: Exercise care in

handling batteries in order not to create a

short circuit with conducting material such

as rings, bracelets and keys. The battery or

conductor may overheat and cause harm.

Observe proper polarity between the

battery and the battery charger.

• Nickel-metal hydride rechargeable

batteries: Dispose of these batteries in a

safe manner. Do not burn or puncture the

battery. Like other batteries of this type, if

burned or punctured, they could release

caustic material which could cause injury.

1 set for IS8129

2 sets for IS8129-2

3 sets for IS8129-3

4 sets for IS8129-4

5 sets for IS8129-5

1 set for DS6951-2

2 sets for DS6951-3/VS306-3

3 sets for DS6951-4/VS306-4

4 sets for DS6951-5/VS306-5

Install the battery

This feature assists you to do the basic setup of the answering

system. You can follow the voice guide to record your own

announcement, set the number of rings and the message alert tone.

When the telephone base prompts you to set up the answering

system via voice guide:

*Includes licenced QaltelTM technology.

QaltelTM is a trademark of Truecall Group Limited.

Download a cell phone phonebook using the

telephone base

Activate remote voice control

Make sure your cell phone is paired and connected to your telephone

system via Bluetooth.

Using the cordless handset:

Downloading...

Entries added:

XXX

Intercom

>Bluetooth

2Press q/p to scroll

to Bluetooth, then

press SELECT.

BLUETOOTH

>Download PB

3Press q/p to scroll

to Download PB,

then press SELECT.

1Press VOICE on

the handset.

HANDSET 1

ECO

10:30PM 11/20

Cell phone X 0 0 : 0 5

ECO

Cell phone X 00:05

2When the handset or telephone base plays the conﬁrmation

tone as forwarded by the cell phone’s voice app, start

speaking toward the handset or telephone base, and then

wait for feedback. Make reply to the voice app’s feedback, if

necessary.

Before downloading a phonebook, make sure the cell phone is

paired, active, and connected to your IS8129.

Follow the following

steps to set the

date and time if you

skipped the prompt.

Press q/p to

scroll to Set date/time,

then press SELECT.

Press MENU.

Enter the date, then

press SELECT.

3Enter the time, then

press SELECT.

HANDSET 1

ECO

10:30PM 11/20

Set date/time

ECO

Date: 07/25/22

ECO

Time: 12:05 PM

ECO

BASE

8 /17 5:3 2 a m

MSG#

Bluetooth cell phones

1 or 2 added.

BASE

8 /17 5:3 2 a m

MSG#

1Press MENU on the

telephone base.

BASE

8 /17 5:3 2 a m

MSG#

Using the telephone base:

1Press VOICE on the

telephone base.

BASE

8 /17 5:3 2 a m

MSG#

Go to www.vtechphones.com (US)

to register your product for enhanced

warranty support and latest VTech

product news.

Go to phones.vtechcanada.com (CA)

for latest VTech product news.

IS8129/

IS8129-2/

IS8129-3/

IS8129-4/

IS8129-5

DECT 6.0 cordless telephone

with BLUETOOTH® wireless technology

Scan the QR code for

support information

US CA

HANDSET 1

ECO

10:30PM 10/16

MSG #

NEW

ANS ON

BASE

12/25 10:30PM 0

MSG #

NEW

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1939

THIS SIDE UP

VERS LE HAUT

Ni-MH)

Phonebook

The phonebook can store up to 1,200 entries, which are shared by all

handsets and the telephone base. Each entry may consist of a telephone

number up to 30 digits, and a name up to 15 characters.

Add a phonebook entry

Review phonebook entries

Delete a phonebook entry

Phonebook

When your desired phonebook entry displays:

Answering system

Dial a phonebook entry

When your desired phonebook entry displays:

Christine Smith

888-883-2445

ECO

Telephone base:

- OR -

Handset:

- OR -

Christine Smith

888-883-2445

ECO

10:30PM 11/20

Handset: Telephone base:

- OR -

Press

If you subscribe to caller ID service, information about each caller appears after the ﬁrst or second ring.

The caller ID log stores up to 50 entries. Each entry has up to 24 digits for the phone number and 15 characters for the name.

Dial a caller ID log entry

Caller ID

Save a caller ID log entry to the phonebook

When your desired caller ID entry displays on the handset

or telephone base screen:

When your

desired caller ID

entry displays on

the handset:

Christine Smith

888-883-2445

ECO

10:30PM 11/20

Christine Smith

888-883-2445

ECO

10:30PM 11/20

1Press MENU.

To Phonebook

ECO

2Press SELECT to

choose To Phonebook.

Enter number

888-883-2445

ECO

3Edit the number

if needed, then

press SELECT.

Chris

ECO

Edit the name

if needed, then

press SELECT.

Saved

ECO

Telephone base:

- OR -

Handset:

- OR -

Press

Delete a caller ID log entry

When your desired caller ID entry displays on the handset or

telephone base screen:

Christine Smith

888-883-2445

ECO

10:30PM 11/20

Handset: Telephone base:

- OR -

Press

Press CID.

HANDSET 1

ECO

10:30PM 11/20

1Press q/p to

browse the entries.

Christine Smith

888-883-2445

ECO

10:30PM 11/20

Handset:

BASE

8 /17 5:3 2 a m

MSG#

1Press q/p to

browse the entries.

Christine Smith

888-883-2445

8 /17 5:3 2 a m

MSG#

Telephone base:

Chris

ECO

4Enter the name,

then press SELECT.

Saved

ECO

HANDSET 1

ECO

10:30PM 11/20

1Press MENU.

Phonebook

ECO

2Press q/p to

scroll to Phonebook,

then press SELECT.

Press SELECT to

select Add new

entry.

Add new entry

ECO

Enter number

888-883-2445

ECO

5Enter the number,

then press SELECT.

Press .

HANDSET 1

ECO

10:30PM 11/20

1Press q/p to

browse the entries.

Christine Smith

888-883-2445

ECO

10:30PM 11/20

Review caller ID log entries

About the built-in answering system and voicemail service

For message recording, your telephone has a built-in answering system, and it also supports

voicemail service offered by your telephone service provider (subscription is required, and fee

may apply).

Built-in answering system VS Voicemail service

Built-in answering system Voicemail service

Supported by Telephone system Telephone service provider

Subscription No Yes

Fees No May apply

Answer

incoming calls

• After 4 rings by default.

• It can be changed in the handset or

the telephone base menu.

• Usually after 2 rings.

• It can be changed by

contacting your telephone

service provider.

Storage Telephone base Server or System

Display new

messages

• Handset - XX new messages

• Telephone base - XX New messages • Handset -

• Telephone base -

Retrieve

messages

• Press on the telephone base;

• Press MENU, and then select Play

messages on the handset; OR

• Access remotely with an access code.

• Press and hold on the

dialpad, and enter an access

number from your telephone

service provider; OR

• Press and hold to dial if

you have saved the access

number.

Turn the built-in answering

system on or off

On the telephone base:

Message playback

Play the previous message

Press to turn on;

press again to turn off.

HANDSET 1

ECO

10:30PM 11/20

1Press MENU.Press SELECT

to select Play

messages.

Play messages

ECO

Handset:

Telephone base:

Press

Options while message playback

Skip a message

Repeat the playing message

Telephone base:

Handset:

Press - OR -

Telephone base:

- OR -

Handset:

Press

Handset:

Telephone base:

Press - OR -

Press

Delete all old messages

Handset:

Telephone base:

Press

Set number of rings

You can set your answering system to answer calls at least two rings earlier than your voicemail service. For

example, if your voicemail service answers after six rings, set your answering system to answer after four rings.

Thus, if you are on a call, or if the answering system is busy recording a message and you receive another call,

the second caller can leave a voicemail message.

HANDSET 1

ECO

10:30PM 11/20

1Press MENU.

ECO

5Press q/p to scroll to desired

number of rings, then press SELECT.

Answering sys

ECO

2Press q/p to scroll

to Answering sys,

then press SELECT.

Press q/p to scroll

to Ans sys setup, then

press SELECT.

Ans sys setup

ECO

# of rings

ECO

4Press q/p to

scroll to # of rings,

then press SELECT.

HANDSET 1

ECO

10:30PM 11/20

1Press MENU.Press q/p to scroll

to Answering sys,

then press SELECT.

Answering sys

ECO

2Press q/p to scroll

to Delete all old, then

press SELECT.

Delete all old

ECO

For C-UL compliance only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de blessures corporelles ou d’électrocution,

suivez toujours ces mesures préventives de base lorsque vous utilisez votre téléphone :

1. Lisez et comprenez bien toutes les instructions.

2. Observez toutes les instructions et mises en garde inscrites sur l’appareil.

3. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas

de nettoyeurs liquides ni en aérosol. N’utilisez qu’un chiffon doux et légèrement

humecté.

4. ATTENTION: Ne pas installer le socle téléphonique à une hauteur supérieure à 2

mètres.

5. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier

de cuisine, d’un bac de lavage ou d’une piscine, ou dans un sous-sol humide ou sous

la douche.

6. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil

pourrait tomber et être sérieusement endommagé.

7. Évitez d’installer le système téléphonique dans les endroits soumis à une température

extrême, à la lumière directe du soleil ou à proximité immédiate d’autres appareils

électriques ou électroniques. Protégez votre téléphone contre les sources

d’humidité, la poussière, les vapeurs et les liquides corrosifs.

8. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière

ou en dessous. Aﬁn d’empêcher la surchauffe, ces ouvertures ne doivent pas être

obstruées en plaçant l’appareil sur un lit, divan, tapis ou autre surface similaires.

Ne placez pas cet appareil à proximité d’un élément de chauffage ni d’une plinthe

électrique. De plus, ne l’installez pas dans une unité murale ou un cabinet fermé

qui ne possède pas d’aération adéquate.

9. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les

étiquettes de l’appareil. Si vous ne connaissez pas le voltage de votre maison,

consultez votre marchand ou votre fournisseur d’électricité.

10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit

sécuritaire, là où personne ne pourra trébucher sur la ligne d’alimentation ni le

cordon téléphonique modulaire.

11. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils

pourraient toucher à des points de tension dangereux ou court-circuiter des pièces,

ce qui constituerait un risque d’incendie ou d’électrocution. N’échappez pas de

liquides dans l’appareil.

12. Aﬁn de réduire les risques d’électrocution, ne démontez pas l’appareil, mais

apportez-le plutôt à un centre de service qualiﬁé s’il doit être réparé. En enlevant

le couvercle, vous vous exposez à des tensions dangereuses ou autres dangers

similaires. Un remontage inadéquat peut être à l’origine d’une électrocution lors

d’une utilisation ultérieure de l’appareil. Débranchez l’appareil avant de procéder

au nettoyage. Utilisez un chiffon humide et doux.

13. Ne surchargez pas les prises de courant et les rallonges.

14. Débranchez cet appareil de la prise de courant et communiquez avec le

département de service à la clientèle de VTech dans les cas suivants :

• Lorsque le cordon d’alimentation est endommagé ou écorché.

• Si du liquide a été échappé dans l’appareil.

• Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.

• Si le produit ne fonctionne pas normalement en respectant les instructions de

fonctionnement. Réglez uniquement les commandes indiquées dans le les

instructions de fonctionnement. Les réglages incorrects des autres commandes

pourraient provoquer un dommage qui pourrait exiger un travail exhaustif de

la part d’un technicien autorisé aﬁn de rétablir le fonctionnement normal de

l’appareil.

• Si le produit a été échappé et que le socle et/ou le combiné a été endommagé.

• Si le produit afﬁche une nette diminution de sa performance.

15. Évitez d’utiliser un téléphone (autre qu’un sans ﬁl) pendant un orage. Les éclairs

peuvent être à l’origine d’une électrocution.

16. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite.

En certaines circonstances, une ﬂammèche pourrait être provoquée lorsque

l’adaptateur est branché à une prise de courant, ou lorsque le combiné est

déposé sur le socle. Ceci est un événement commun associé à la fermeture d’un

circuit électrique. L’utilisateur ne devrait pas brancher le téléphone à une prise de

courant, et ne devrait pas déposer le combiné chargé sur le socle, si le téléphone

se trouve à proximité d’un endroit comportant des concentrations de gaz

inﬂammables, à moins que la ventilation soit adéquate. Une ﬂammèche dans un tel

endroit pourrait provoquer un incendie ou une explosion. De tels environnements

peuvent comprendre: des endroits où l’on utilise de l’oxygène médical sans

ventilation adéquate; des gaz industriels (dissolvants de nettoyage, des vapeurs

d’essence, etc.); une fuite de gaz naturel, etc.

17. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode

de conversation.

18. Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au

sol. Les broches ne sont pas conçues pour maintenir l’adaptateur en place si celui-ci

est barnché dans une prise au plafond ou sous une table/ armoire.

19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le socle de prise de courant

doit etre installe a proximite du materiel et doit etre aisement accessible.

20. MISE EN GARDE: Il peut y avoir un risque d’explosion si vous utilisez le

mauvais type de piles pour le téléphone. N’utilisez que les piles rechargeable inclus

ou les piles de rechange (BT162342/BT262342). N’incinérez pas les piles. Celles-ci

risqueraient d’exploser.

• Évite d’utiliser la batterie dans les conditions suivantes:

» des températures extrêmes faibles ou élevées auxquelles une batterie peut être

soumise pendant l’utilisation, le stockage ou le transport;

» Remplacement d’une batterie par un type incorrect pouvant supprimer une

protection;

» mise au rebut d’une batterie dans un feu ou dans un four chaud, ou écrasement

mécanique ou coupure d’une batterie, susceptible de provoquer une explosion;

» maintien d’une batterie dans un environnement à très haute température pouvant

provoquer une explosion ou la fuite de liquide ou de gaz inﬂammables;

» batterie soumise à une pression de l’air extrêmement faible pouvant provoquer

une explosion ou la fuite de liquide ou de gaz inﬂammables.

21. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur

dont la polarité ou la tension serait inadéquate risque d’endommager sérieusement

le produit et mettre votre sécurité en péril.

22. La plaque signalétique appliquée est située au bas ou à proximité du produit.

CONSERVEZ CES INSTRUCTIONS

Pile

• N’utilisez que la pile incluse ou l’équivalent. Pour commander une pile de recharge,

visitez notre site Web au www.vtechphones.com ou composez le 800-595-9511. Au

Canada, visitez le phones. phones.vtechcanada.com ou composez le 800-267-7377.

• Ne jetez pas la pile au feu. Vériﬁez les instructions spéciﬁques de mise aux rebus

auprès des autorités locales.

• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif

et pourrait causer des brûlures ou des blessures aux yeux ou à la peau. L’électrolyte

est toxique si avalé.

• Soyez prudents lorsque vous manipulez les piles aﬁn d’éviter les courts-circuits

provoqués par des matériaux conducteurs.

• Rechargez la pile incluse avec cet appareil, selon les instructions et limites spéciﬁées

dans ce guide d’utilisation.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans

ﬁl) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une ﬁrme de recherche

indépendante, a mené une évaluation pluridisciplinaire des interférences entre les

téléphones sans ﬁl portatifs et les stimulateurs cardiaques implantés dans l’organisme.

Appuyée par l’Administration des aliments et drogues (FDA) des États-Unis, la ﬁrme

WTR recommande aux médecins :

Avis aux détenteurs de stimulateurs cardiaques

• Ils doivent tenir le téléphone sans ﬁl à une distance d’au moins six pouces du

stimulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement sur le stimulateur

cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche.

• Ils doivent utiliser le téléphone sans ﬁl en l’appuyant sur l’oreille qui se trouve dans

la direction opposée au stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de risque pour les détenteurs

de simulateurs cardiaques causés par les gens qui utilisent un téléphone sans ﬁl à

proximité de ceux-ci.

À propos des téléphones sans ﬁl

Conﬁdentialité : Les mêmes caractéristiques qui constituent des avantages pour les

téléphones sans ﬁl afﬁchent également des restrictions. Les appels téléphoniques

sont transmis entre le combiné sans ﬁl et le socle par le biais d’ondes radio ; il y a donc

la possibilité que vos conversations téléphoniques sans ﬁl soient interceptées par des

équipements de réception radio se trouvant dans la portée du combiné sans ﬁl. Pour

cette raison, vous ne devez pas percevoir les communications téléphoniques sans ﬁl

comme étant aussi conﬁdentielles que celles des téléphones à cordons.

Alimentation électrique : Le socle de ce téléphone sans ﬁl doit être branché à une

prise électrique fonctionnelle. La prise électrique ne doit pas être contrôlée par un

interrupteur mural. Les appels ne pourront pas être effectués du combiné sans ﬁl si le

socle est débranché ou mis hors tension ou si le courant est coupé.

Possibilité d’interférences aux téléviseurs : Certains téléphones sans ﬁl fonctionnent

sur des fréquences pouvant causer des interférences aux téléviseurs et aux

magnétoscopes. Pour réduire ou prévenir de telles interférences, ne placez pas le

socle du téléphone sans ﬁl près ou sur un téléviseur ou magnétoscope. S’il y a présence

de parasites, il est conseillé d’éloigner le téléphone sans ﬁl du téléviseur ou du

magnétoscope aﬁn de réduire possiblement les interférences.

Piles rechargeables : Manipulez les piles avec soin aﬁn de ne pas les court-circuiter avec

des bagues, bracelets ou clés. Les piles ou le conducteur peut surchauffer et causer des

blessures. Respectez la polarité adéquate entre la pile et le chargeur.

Les bloc-piles rechargeables à l’hydrure métallique de nickel : Jetez ces blocs-piles de

manière écologique et sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les

autres piles de ce type, elles pourraient dégager une matière toxique qui peut causer

des blessures corporelles si elles sont brûlées ou percées.

The RBRC seal

The RBRC seal on the nickel-metal hydride battery indicates that VTech

Communications, Inc. is voluntarily participating in an industry program to

collect and recycle these batteries at the end of their useful lives, when

taken out of service within the United States and Canada.

The program provides a convenient alternative to placing used nickel-

metal hydride batteries into the trash or municipal waste, which may be

illegal in your area.

VTech’s participation makes it easy for you to drop off the spent battery at local retailers

participating in the RBRC program or at authorized VTech product service centers. Please

call 1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/

restrictions in your area. VTech’s involvement in this program is part of its commitment to

protecting our environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

FCC, ACTA and IC regulations

FCC Part 15

NOTE: This equipment has been tested and found to comply with the requirements

for a Class B digital device under Part 15 of the Federal Communications Commission

(FCC) rules. These requirements are intended to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by

the party responsible for compliance could void the user’s authority to operate the

equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause

undesired operation. Privacy of communications may not be ensured when using this

telephone.

To ensure safety of users, the FCC/ISEDC has established criteria for the amount of radio

frequency energy that can be safely absorbed by a user or bystander according to the

intended usage of the product. This product has been tested and found to comply with

the FCC/ISEDC criteria. The handset may be safely held against the ear of the user. The

telephone base shall be installed and used such that parts of the user’s body other than

the hands are maintained at a distance of approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical requirements

adopted by the Administrative Council for Terminal Attachments (ACTA). The label

on the back or bottom of this equipment contains, among other things, a product

identiﬁer in the format US:AAAEQ##TXXXX. This identiﬁer must be provided to your

telephone service provider upon request.

The plug and jack used to connect this equipment to premises wiring and the

telephone network must comply with applicable Part 68 rules and technical

requirements adopted by ACTA. A compliant telephone cord and modular plug is

provided with this product. It is designed to be connected to a compatible modular

jack that is also compliant. An RJ11 jack should normally be used for connecting to a

single line. See the installation instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to determine how many devices you

may connect to your telephone line and still have them ring when you are called.

The REN for this product is encoded as the 6th and 7th characters following the US:

in the product identiﬁer (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the

sum of all RENs should be ﬁve (5.0) or less. For more information, please contact your

telephone service provider.

This equipment must not be used with Party Lines. If you have specially wired alarm

dialing equipment connected to your telephone line, ensure the connection of this

equipment does not disable your alarm equipment. If you have questions about what

will disable alarm equipment, consult your telephone service provider or a qualiﬁed

installer.

If this equipment is malfunctioning, it must be unplugged from the modular jack until

the problem has been corrected. Replacement to this telephone equipment can only

be made by the manufacturer or its authorized agents. For replacement procedures,

follow the instructions outlined under the Limited warranty.

If this equipment is causing harm to the telephone network, the telephone service

provider may temporarily discontinue your telephone service. The telephone service

provider is required to notify you before interrupting service. If advance notice is not

practical, you will be notiﬁed as soon as possible. You will be given the opportunity to

correct the problem and the telephone service provider is required to inform you of

your right to ﬁle a complaint with the FCC. Your telephone service provider may make

changes in its facilities, equipment, operation, or procedures that could affect the

proper functioning of this product. The telephone service provider is required to notify

you if such changes are planned.

If this product is equipped with a corded or cordless handset, it is hearing aid

compatible.

If this product has memory dialing locations, you may choose to store emergency

telephone numbers (e.g., police, ﬁre, medical) in these locations. If you do store or test

emergency numbers, please:

Remain on the line and brieﬂy explain the reason for the call before hanging up.

Perform such activities in off-peak hours, such as early morning or late evening.

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with

Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause

undesired operation of the device.

Privacy of communications may not be ensured when using this telephone.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the

Industry Canada technical speciﬁcations were met.

The Ringer Equivalence Number (REN) for this terminal equipment is 1.0. The REN

indicates the maximum number of devices allowed to be connected to a telephone

interface. The termination of an interface may consist of any combination of devices

subject only to the requirement that the sum of the RENs of all the devices not exceed

ﬁve.

This product meets the applicable Innovation, Science and Economic Development

Canada technical speciﬁcations.

California Energy Commission battery

charging testing instructions

This telephone is set up to comply with the energy-conserving standards right out of the

box. These instructions are intended for California Energy Commission (CEC) compliance

testing only. When the CEC battery charging testing mode is activated, all telephone

functions, except battery charging, will be disabled.

To activate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power outlet. Make sure all

handsets are plugged with charged batteries before proceeding.

2. While you press and hold FIND HS, plug the telephone base power adapter back to

the power outlet.

3. After about 20 seconds, when the HOME light starts ﬂashing, release FIND HS and

then press it again within two seconds. You hear a conﬁrmation tone. The HOME light

turns off and all handsets display To register HS... see manual alternately. Allow up to

one minute for the process to complete.

If the phone fails to enter this mode, repeat all the steps mentioned above. The

telephone base will be powered up as normal if you fail to press FIND HS within two

seconds in Step 3.

To deactivate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power outlet, and then plug it

back in. Then the telephone base is powered up as normal.

2. Put the handsets on the telephone base cradle to begin registration.

3. The handset shows Registering... If the registration is successful, the handset screen

displays Registered and beeps. The handset is registered with the telephone base.

Limited Warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase

(“Consumer” or “you”) that the Product and all accessories provided in the sales package

(“Product”) are free from defects in material and workmanship, pursuant to the following

terms and conditions, when installed and used normally and in accordance with the

Product operating instructions. This limited warranty extends only to the Consumer for

Products purchased and used in the United States of America and Canada.

What will VTech do if the Product is not free from defects in materials and

workmanship during the limited warranty period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service representative will

replace at VTech’s option, without charge, a Materially Defective Product. If we replace

the Product, we may use new or refurbished replacement parts. If we choose to replace

the Product, we may replace it with a new or refurbished Product of the same or similar

design. We will retain defective parts, modules, or equipment. Replacement of the

Product, at VTech’s option, is your exclusive remedy. VTech will return the replacement

Products to you in working condition. You should expect the replacement to take

approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of

purchase. If VTech replaces a Materially Defective Product under the terms of this limited

warranty, this limited warranty also applies to the replacement Product for a period of

either (a) 90 days from the date the replacement Product is shipped to you or (b) the

time remaining on the original one-year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical

damage, improper installation, abnormal operation or handling, neglect,

inundation, ﬁre, water or other liquid intrusion.

2. Product that has been subjected to contact with liquid, water, rain, extreme

humidity or heavy perspiration, sand, dirt or the like; but then only to the extent

the damage was not caused by incorrectly securing the waterproof handset’s

protective elements, for example, failing to properly close a seal), or such

protective elements are damaged or missing (e.g. a cracked battery door), or

subjecting a Product to conditions beyond its stated speciﬁcations or limits (e.g. 30

minutes in 1 meter of fresh water).

3. Product that has been damaged due to repair, alteration or modiﬁcation by

anyone other than an authorized service representative of VTech;

4. Product to the extent that the problem experienced is caused by signal conditions,

network reliability, or cable or antenna systems;

5. Product to the extent that the problem is caused by use with non-VTech

accessories;

6. Product whose warranty/quality stickers, product serial number plates or electronic

serial numbers have been removed, altered or rendered illegible;

7. Product purchased, used, serviced, or shipped for repair from outside the United

States of America or Canada, or used for commercial or institutional purposes

(including but not limited to Products used for rental purposes);

8. Product returned without a valid proof of purchase (see item 2 below); or

9. Charges for installation or set up, adjustment of customer controls, and installation

or repair of systems outside the unit.

How do you get warranty service?

To obtain warranty service in the United States of America, please visit our website at

www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to

phones.vtechcanada.com or dial 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s manual - a check of the Product’s

controls and features may save you a service call.

Except as provided by applicable law, you assume the risk of loss or damage during

transit and transportation and are responsible for delivery or handling charges incurred

in the transport of the Product(s) to the service location. VTech will return replaced

Product under this limited warranty. Transportation, delivery or handling charges are

prepaid.

VTech assumes no risk for damage or loss of the Product in transit. If the Product failure

is not covered by this limited warranty, or proof of purchase does not meet the terms

of this limited warranty, VTech will notify you and will request that you authorize the

cost of replacement prior to any further replacement activity. You must pay for the cost

of replacement and return shipping costs for the replacement of Products that are not

covered by this limited warranty.

What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech

service location along with a description of the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt) identifying the Product

purchased (Product model) and the date of purchase or receipt; and

3. Provide your name, complete and correct mailing address, and telephone

number.

Other limitations

This warranty is the complete and exclusive agreement between you and VTech. It

supersedes all other written or oral communications related to this Product. VTech

provides no other warranties for this Product. The warranty exclusively describes all of

VTech’s responsibilities regarding the Product. There are no other express warranties.

No one is authorized to make modiﬁcations to this limited warranty and you should not

rely on any such modiﬁcation.

State/Provincial Law Rights: This warranty gives you speciﬁc legal rights, and you may

also have other rights, which vary from state to state or province to province.

Limitations: Implied warranties, including those of ﬁtness for a particular purpose and

merchantability (an unwritten warranty that the Product is ﬁt for ordinary use) are limited

to one year from the date of purchase. Some states/provinces do not allow limitations

on how long an implied warranty lasts, so the above limitation may not apply to you.

In no event shall VTech be liable for any indirect, special, incidental, consequential, or

similar damages (including, but not limited to lost proﬁts or revenue, inability to use the

Product or other associated equipment, the cost of substitute equipment, and claims

by third parties) resulting from the use of this Product. Some states/provinces do not

allow the exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof of purchase

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage

or loss resulting from the use of this user’s manual. VTech Communications, Inc. and its

suppliers assume no responsibility for any loss or claims by third parties that may arise

through the use of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States

Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada

Delete entry?

ECO

Press SELECT.

LCD language setting

If you accidentally set the LCD language to Spanish

or French, you can change the LCD language back to

English while the telephone is not in use:

• On the telephone base, press MENU and then enter

364#.

• On the handset, press MENU and then enter 364#.

You can set the answering system to answer an incoming call

after 2, 3, 4, 5 or 6 rings; or Toll saver.

If you choose Toll saver, the answering system answers a call

after two rings when you have new messages, or after four

rings when you have no new messages. This enables you to

check for new messages and avoid paying unnecessary long

distance charges if you are calling from outside your local area.

NOTE

Press CID.

VTech IS8129 Manuel utilisateur

Marque: VTech

Modèle: IS8129

Catégorie: Téléphones

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: VTech IS8129 User manual

VTech IS8129 Manuel utilisateur

VTech IS8129 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents