Quick start guide
What’s in the box
Connect the telephone base Connect the charger
Charge the battery
Specifications are subject to change without notice.
© 2021 VTech Communications, Inc.|
© 2021 VTech Technologies Canada Ltd.
All rights reserved. 09/21. DS6951-X_QSG_V1.1
Telephones identified with this logo have reduced noise and
interference when used with most T-coil equipped hearing aids and
cochlear implants. The TIA-1083 Compliant Logo is a trademark of
the Telecommunications Industry Association. Used under license.
T
Compatible with
Hearing
Ai
d T-Coil
TIA-1083
The ENERGY STAR® program (www.energystar.gov) recognizes and
encourages the use of products that save energy and help protect our
environment. We are proud to mark this product with the ENERGY
STAR® label indicating it meets the latest energy efficiency guidelines.
12 hrs
Technical specifications
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Handset: 1921.536-1928.448 MHz
Telephone base: 1921.536-1928.448 MHz
Channels 5
Nominal effective
range
Maximum power allowed by FCC and IC.
Actual operating range may vary according to
environmental conditions at the time of use.
Power requirement Handset: 2.4V Ni-MH battery
Telephone base: 6V DC @ 600mA
Charger: 6V DC @ 400mA
Memory Phonebook: 1000 memory locations;
up to 30 digits and 15 characters
Caller ID log: 50 memory locations;
up to 24 digits and 15 characters
Call block: 1000 entries
If you subscribe to digital subscriber
line (DSL) high-speed Internet service
through your telephone line, make
sure you connect a DSL filter (not
included) to the telephone wall jack.
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 300mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR2105
Connect and install
1
Quick
start
guide
Introducing
Smart call
blocker
Display
Handset:
The handset battery is low and needs charging.
The handset battery is charging.
The handset battery is fully charged.
Handset or telephone base ringer is off.
New voicemail received from your telephone service
provider.
NEW
There are new caller ID log entries.
Displays when Home line is in use.
Bluetooth device is paired and active.
Bluetooth device / Cell line is in use.
ANS ON Answering system is on.
10/16
MSG # Handset displays the current message number being played
and the total number of new/old messages recorded.
MSG#
0Telephone base message counter displays the total
number of messages.
ECO The ECO mode activates automatically to reduce power
consumption when the handset is within range of the
telephone base.
To use a Bluetooth enabled cellular phone or headset with your telephone, you must first pair and connect your Bluetooth cellular phone or
headset with the telephone base. Before you begin, make sure that you have cellular coverage and your Bluetooth enabled cell phone or
headset is not connected to any other Bluetooth device.
Add a Bluetooth cell phone Add a Bluetooth headset
The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use
of such marks by VTech Holdings Limited is under license. VTech Holdings Limited
is a member of Bluetooth SIG, Inc. Other trademarks and trade names are those of
their respective owners.
Telephone base:
Setup
2
After you install your telephone or power returns following
a power outage and battery depletion, the handset and
telephone base will prompt you to set the date and time, and
to configure the Smart call blocker* and answering system
through voice guide.
Date and time
Follow the steps below to set the date and time.
For example, if the date is 25 June, 2021, and the time is 12:05 PM:
Voice guide for Smart call blocker / Answering system
After setting the date and time, the telephone base will prompt
if you want to set Smart call blocker, and the answering system.
For more details, see Use voice guide to set Smart call blocker in
the Introducing Smart call blocker leaflet and Use voice guide
to set Answsering system in the online help topics.
When the telephone base prompts you to set up the Smart call
blocker via voice guide:
When the handset
and telephone
base prompt you
to set the date and
time:
Date: MM/DD/YY
ECO
Date: 06/25/21
ECO
Press SELECT.
2
Time: 12:05 PM
ECO
Press SELECT.
4
Setup your answering system by
inputting the designated numbers
as instructed in the voice guide.
Voice guide to
set up Ans sys?
Press MENU on the
telephone base to start
voice guide setup.
2
“This voice guide will assist
you with the basic setup of
your answering system“
“Hello! This voice guide will
assist you with the basic
setup of Smart call blocker“
Voice guide set
Smart call blk?
Press MENU on the
telephone base to start
voice guide setup.
1
Setup your Smart call blocker by
inputting the designated numbers
as instructed in the voice guide.
Make a home call
Operate
3
End a home call
For operations and guides to help you using your telephone system,
and for latest information and supports, go and check the online help
topics and online FAQs.
Use your smartphone or mobile device to access our online help.
• Go to https://help.vtechphones.com/ds6951; OR
• Scan the QR code on the right. Launch the camera app or QR
code scanner app on your smartphone or tablet. Hold the device’s
camera up to the QR code and frame it.
Volume
Handset: Telephone base:
Handset: Telephone base:
End a cell call
Handset: Telephone base:
Make a cell call
Answer a home call
Telephone base:
Handset:
- OR -
Answer a cell call
Telephone base:
Handset:
- OR -
Handset:
- OR -
Telephone base:
- OR -
Handset: Telephone base:
- OR -
Tap the notification to trigger the redirection of the online help.
- If the QR code is not clearly displayed, adjust your camera’s focus
by moving your device closer or
further away until it is clear.
You can also call our
Customer Support at
1 (800) 595-9511 [in US] or
1 (800) 267-7377 [in Canada]
for help.
Need help?
Date: 06/2?/--
ECO
Enter the date.
1
Time: HH:MM -
-
ECO
Enter the time.
3
Enter the phone number.
2
Enter the phone number.
2
Press
1
Press
1
Press
Press
Press
Press
Press
Bluetooth
A d di n g c ell...
4Turn on the Bluetooth
feature of your cell phone.
1Press MENU on the
telephone base.
BASE
8 /17 5:32 a m
MSG#
0
Intercom
>Bluetooth
2Press q/p to scroll
to Bluetooth, then
press SELECT.
BLUETOOTH
> A dd c ellula r
3Press SELECT to
select Add cellular.
Once your cell phone
finds your telephone
(VTech DECT 6.0), press
the appropriate key
on your cell phone to
continue the pairing
process.
5
Search headset...
4Set your headset to
discoverable mode.
Bluetooth headset
2 added.
1Press MENU on the
telephone base.
BASE
8 /17 5:32 a m
MSG#
0
Intercom
>Bluetooth
2Press q/p to scroll
to Bluetooth, then
press SELECT.
BLUETOOTH
>Add headset
3Press q/p to scroll
to Add headset,
then press SELECT.
Refer to the user’s
manual of your
Bluetooth headset on
how to pair it to your
DS6951 telephone.
5
When using your telephone equipment, basic
safety precautions should always be followed to
reduce the risk of fire, electric shock and injury,
including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked
on the product.
3. Unplug this product from the wall outlet
before cleaning. Do not use liquid or
aerosol cleaners. Use a damp cloth for
cleaning.
4. CAUTION: Do not install the telephone
base at a height above 2 meters.
5. Do not use this product near water such as
near a bath tub, wash bowl, kitchen sink,
laundry tub or a swimming pool, or in a wet
basement or shower.
6. Do not place this product on an unstable
table, shelf, stand or other unstable
surfaces.
7. Avoid placing the telephone system in
places with extreme temperature, direct
sunlight, or other electrical devices. Protect
your phone from moisture, dust, corrosive
liquids and fumes.
8. Slots and openings in the back or bottom
of the telephone base and handset are
provided for ventilation. To protect them
from overheating, these openings must not
be blocked by placing the product on a
soft surface such as a bed, sofa or rug. This
product should never be placed near or
over a radiator or heat register. This product
should not be placed in any area where
proper ventilation is not provided.
9. This product should be operated only
from the type of power source indicated
on the marking label. If you are not sure of
the type of power supply in your home or
office, consult your dealer or local power
company.
10. Do not allow anything to rest on the power
cord. Do not install this product where the
cord may be walked on.
11. Never push objects of any kind into this
product through the slots in the telephone
base or handset because they may touch
dangerous voltage points or create a short
circuit. Never spill liquid of any kind on the
product.
12. To reduce the risk of electric shock, do not
disassemble this product, but take it to
an authorized service facility. Opening or
removing parts of the telephone base or
handset other than specified access doors
may expose you to dangerous voltages
or other risks. Incorrect reassembling can
cause electric shock when the product is
subsequently used.
13. Do not overload wall outlets and extension
cords.
14. Unplug this product from the wall outlet
and refer servicing to an authorized service
facility under the following conditions:
• When the power supply cord or plug is
damaged or frayed.
• If liquid has been spilled onto the
product.
• If the product has been exposed to rain
or water.
• If the product does not operate
normally by following the operating
instructions. Adjust only those controls
that are covered by the operation
instructions. Improper adjustment of
other controls may result in damage
and often requires extensive work by
an authorized technician to restore the
product to normal operation.
• If the product has been dropped and
the telephone base and/or handset has
been damaged.
• If the product exhibits a distinct change
in performance.
15. Avoid using a telephone (other than
cordless) during an electrical storm. There
is a remote risk of electric shock from
lightning.
16. Do not use the telephone to report a
gas leak in the vicinity of the leak. Under
certain circumstances, a spark may be
created when the adapter is plugged into
the power outlet, or when the handset is
replaced in its cradle. This is a common
event associated with the closing of any
electrical circuit. The user should not plug
the phone into a power outlet, and should
not put a charged handset into the cradle,
if the phone is located in an environment
containing concentrations of flammable
or flame-supporting gases, unless there
is adequate ventilation. A spark in such
an environment could create a fire or
explosion. Such environments might
include: medical use of oxygen without
adequate ventilation; industrial gases
(cleaning solvents; gasoline vapors; etc.); a
leak of natural gas; etc.
17. Only put the handset of your telephone
next to your ear when it is in normal talk
mode.
18. The power adapter is intended to be
correctly oriented in a vertical or floor
mount position. The prongs are not
designed to hold the plug in place if it is
plugged into a ceiling, under-the-table or
cabinet outlet.
19. For pluggable equipment, the socket-
outlet shall be installed near the equipment
and shall be easily accessible.
Important safety instructions 20. CAUTION: Use only the
batteries indicated in this manual. There
may be a risk of explosion if a wrong type
of battery is used for the handset. Use
only the supplied rechargeable batteries
or replacement batteries (BT162342/
BT262342) for the handset. Do not dispose
of batteries in a fire. They may explode.
• Do not use the battery in following
conditions:
» High or low extreme temperature
during use, storage or
transportation.
» Replacement of a battery with an
incorrect type that can defeat a
safeguard.
» Disposal of a battery into fire or a
hot oven, or mechanically crushing
or cutting of a battery, that can
result in an explosion.
» Leaving a batteryin an extremely
high temperature surrounding
environment that can result in
an explosion or the leakage of
flammable liquid or gas.
» A battery subjected to extremely
low air pressure that can result in
an explosion or the leakage of
flammable liquid or gas.
21. Use only the adapter included with
this product. Incorrect adapter polarity
or voltage can seriously damage the
product.
22. The applied nameplate is located at the
bottom or near of the product.
SAVE THESE INSTRUCTIONS
Battery
• Use only the batteries provided or
equivalent. To order a replacement, visit
our website at www.vtechphones.com or
call 1 (800) 595-9511. In Canada, go to
phones.vtechcanada.com or call
1 (800) 267-7377.
• Do not dispose of the battery in a fire. Check
with local waste management codes for
special disposal instructions.
Do not open or mutilate the battery.
Released electrolyte is corrosive and may
cause burns or injury to the eyes or skin. The
electrolyte may be toxic if swallowed.
• Exercise care in handling batteries in order
not to create a short circuit with conductive
materials.
• Charge the battery provided with this
product only in accordance with the
instructions and limitations specified in this
manual.
Precautions for users of implanted cardiac
pacemakers
Cardiac pacemakers (applies only to digital
cordless telephones):
Wireless Technology Research, LLC (WTR),
an independent research entity, led a
multidisciplinary evaluation of the interference
between portable wireless telephones and
implanted cardiac pacemakers. Supported by
the U.S. Food and Drug Administration, WTR
recommends to physicians that:
Pacemaker patients
• Should keep wireless telephones at least six
inches from the pacemaker.
• Should NOT place wireless telephones
directly over the pacemaker, such as in a
breast pocket, when it is turned ON.
• Should use the wireless telephone at the ear
opposite the pacemaker.
WTR’s evaluation did not identify any risk to
bystanders with pacemakers from other persons
using wireless telephones.
About cordless telephones
• Privacy: The same features that make a
cordless telephone convenient create some
limitations. Telephone calls are transmitted
between the telephone base and the
cordless handset by radio waves, so there
is a possibility that the cordless telephone
conversations could be intercepted by
radio receiving equipment within range
of the cordless handset. For this reason,
you should not think of cordless telephone
conversations as being as private as those on
corded telephones.
• Electrical power: The telephone base of this
cordless telephone must be connected to a
working electrical outlet. The electrical outlet
should not be controlled by a wall switch.
Calls cannot be made from the cordless
handset if the telephone base is unplugged,
switched off or if the electrical power is
interrupted.
• Potential TV interference: Some cordless
telephones operate at frequencies that may
cause interference to televisions and VCRs.
To minimize or prevent such interference,
do not place the telephone base of the
cordless telephone near or on top of a TV or
VCR. If interference is experienced, moving
the cordless telephone farther away from
the TV or VCR often reduces or eliminates
the interference.
• Rechargeable batteries: Exercise care in
handling batteries in order not to create a
short circuit with conducting material such
as rings, bracelets and keys. The battery or
conductor may overheat and cause harm.
Observe proper polarity between the
battery and the battery charger.
• Nickel-metal hydride rechargeable
batteries: Dispose of these batteries in a
safe manner. Do not burn or puncture the
battery. Like other batteries of this type, if
burned or punctured, they could release
caustic material which could cause injury.
1 set for DS6951
2 sets for DS6951-2
3 sets for DS6951-3/VS306-3
4 sets for DS6951-4/VS306-4
5 sets for DS6951-5/VS306-5
1 set for DS6951-2
2 sets for DS6951-3/VS306-3
3 sets for DS6951-4/VS306-4
4 sets for DS6951-5/VS306-5
Install the battery
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 300mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR2105
THIS SIDE UP
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 300mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1939
This feature assists you to do the basic setup of the answering
system. You can follow the voice guide to record your own
announcement, set the number of rings and the message alert tone.
When the telephone base prompts you to set up the answering
system via voice guide:
*Includes licenced QaltelTM technology.
QaltelTM is a trademark of Truecall Group Limited.
Download a cell phone phonebook using the
telephone base
Activate remote voice control
Make sure your cell phone is paired and connected to your telephone
system via Bluetooth.
Using the cordless handset:
Downloading...
Entries added:
XXX
Intercom
>Bluetooth
2Press q/p to scroll
to Bluetooth, then
press SELECT.
BLUETOOTH
>Download PB
3Press q/p to scroll
to Download PB,
then press SELECT.
1Press VOICE on
the handset.
HANDSET 1
ECO
1
10:30PM 11/20
Cell phone X 0 0 : 0 5
ECO
1
Cell phone X 00:05
2When the handset or telephone base plays the confirmation
tone as forwarded by the cell phone’s voice app, start
speaking toward the handset or telephone base, and then
wait for feedback. Make reply to the voice app’s feedback, if
necessary.
- OR -
Before downloading a phonebook, make sure the cell phone is
paired, active, and connected to your DS6951.
Follow the following
steps to set the
date and time if you
skipped the prompt.
Press q/p to
scroll to Set date/time,
then press SELECT.
2
Press MENU.
1
Enter the date, then
press SELECT.
3Enter the time, then
press SELECT.
4
HANDSET 1
ECO
10:30PM 11/20
Set date/time
ECO
Date: 06/25/21
ECO
Time: 10:59 AM
ECO
BASE
8 /17 5:32 a m
MSG#
0
2
Bluetooth cell phones
1 or 2 added.
BASE
8 /17 5:32 a m
MSG#
0
1
2
1Press MENU on the
telephone base.
BASE
8 /17 5:32 a m
MSG#
0
1
2
Using the telephone base:
1Press VOICE on the
telephone base.
BASE
8 /17 5:32 a m
MSG#
0
1
Go to www.vtechphones.com (US)
to register your product for enhanced
warranty support and latest VTech
product news.
Go to phones.vtechcanada.com (CA)
for latest VTech product news.
DS6951
DS6951-2
DS6951-3
DS6951-4
DS6951-5
VS306-3
VS306-4
VS306-5
DECT 6.0 cordless telephone
with BLUETOOTH® wireless technology
Scan the QR code for
support information
US CA
S
m
US CA
HANDSET 1
ECO
10:30PM 10/16
MSG #
NEW
ANS ON
BASE
12/25 10:30PM 0
MSG #
NEW
Phonebook
The phonebook can store up to 1,000 entries, which are shared by all
handsets and the telephone base. Each entry may consist of a telephone
number up to 30 digits, and a name up to 15 characters.
Add a phonebook entry
Review phonebook entries
Delete a phonebook entry
Phonebook
When your desired phonebook entry displays:
Answering system
Dial a phonebook entry
When your desired phonebook entry displays:
Christine Smith
888-883-2445
ECO
Telephone base:
- OR -
- OR -
Handset:
- OR -
Christine Smith
888-883-2445
ECO
10:30PM 11/20
Handset: Telephone base:
- OR -
Press
Press
If you subscribe to caller ID service, information about each caller appears after the first or second ring.
The caller ID log stores up to 50 entries. Each entry has up to 24 digits for the phone number and 15 characters for the name.
Dial a caller ID log entry
Caller ID
Save a caller ID log entry to the phonebook
When your desired caller ID entry displays on the handset
or telephone base screen:
When your
desired caller ID
entry displays on
the handset:
Christine Smith
888-883-2445
ECO
10:30PM 11/20
Christine Smith
888-883-2445
ECO
10:30PM 11/20
1Press MENU.
To Phonebook
ECO
2Press SELECT to
choose To Phonebook.
Enter number
888-883-2445
ECO
3Edit the number
if needed, then
press SELECT.
Enter name
Chris
ECO
4
Edit the name
if needed, then
press SELECT.
Saved
ECO
Telephone base:
- OR -
- OR -
Handset:
- OR -
Press
Delete a caller ID log entry
When your desired caller ID entry displays on the handset or
telephone base screen:
Christine Smith
888-883-2445
ECO
10:30PM 11/20
Handset: Telephone base:
- OR -
Press
Press qCID.
HANDSET 1
ECO
1
10:30PM 11/20
1Press q/p to
browse the entries.
2
Christine Smith
888-883-2445
ECO
10:30PM 11/20
Handset:
BASE
8 /17 5:32 a m
MSG#
0
1Press Press q/p to
browse the entries.
2
Christine Smith
888-883-2445
8 /17 5:32 a m
MSG#
0
Telephone base:
Enter name
Chris
ECO
4Enter the name,
then press SELECT.
Saved
ECO
HANDSET 1
ECO
1
10:30PM 11/20
1Press MENU.
Phonebook
ECO
2Press q/p to
scroll to Phonebook,
then press SELECT.
Press SELECT to
select Add new
entry.
Add new entry
ECO
3
Enter number
888-883-2445
ECO
5Enter the number,
then press SELECT.
Press p.
HANDSET 1
ECO
1
10:30PM 11/20
1Press q/p to
browse the entries.
2
Christine Smith
888-883-2445
ECO
10:30PM 11/20
Review caller ID log entries
About the built-in answering system and voicemail service
For message recording, your telephone has a built-in answering system, and it also supports
voicemail service offered by your telephone service provider (subscription is required, and fee
may apply).
Built-in answering system VS Voicemail service
Built-in answering system Voicemail service
Supported by Telephone system Telephone service provider
Subscription No Yes
Fees No May apply
Answer
incoming calls
• After 3 rings by default.
• It can be changed in the handset or
the telephone base menu.
• Usually after 2 rings.
• It can be changed by
contacting your telephone
service provider.
Storage Telephone base Server or System
Display new
messages
• Handset - XX New Messages
• Telephone base - XX New Messages • Handset -
• Telephone base -
Retrieve
messages
• Press on the telephone base;
OR
• Press MENU, and then select Play
messages on the handset; OR
• Access remotely with an access code.
• Press on the dialpad,
and enter an access number
from your telephone service
provider.
Turn the built-in answering
system on or off
On the telephone base:
Message playback
Play the previous message
Press to turn on;
press again to turn off.
HANDSET 1
ECO
1
10:30PM 11/20
1Press MENU.Press SELECT
to select Play
mesages.
Play messages
ECO
2
Handset:
Telephone base:
Press
Options while message playback
Skip a message
Repeat the playing message
Telephone base:
Handset:
Press - OR -
Telephone base:
- OR -
Handset:
Press
Handset:
1
2
Telephone base:
1
2
Press - OR -
Press
Delete all messages
Handset:
Telephone base:
1
2
Press
Set number of rings
You can set your answering system to answer calls at least two rings earlier than your voicemail service. For
example, if your voicemail service answers after six rings, set your answering system to answer after four rings.
Thus, if you are on a call, or if the answering system is busy recording a message and you receive another call,
the second caller can leave a voicemail message.
HANDSET 1
ECO
1
10:30PM 11/20
1Press MENU.
3
ECO
5Press q/p to scroll to desired
number of rings, then press SELECT.
Answering sys
ECO
2Press q/p to scroll
to Answering sys,
then press SELECT.
Press q/p to scroll
to Ans sys setup, then
press SELECT.
Ans sys setup
ECO
3
# of rings
ECO
4Press q/p to
scroll to # of rings,
then press SELECT.
HANDSET 1
ECO
1
10:30PM 11/20
1Press MENU.Press q/p to scroll
to Answering sys,
then press SELECT.
Answering sys
ECO
2Press q/p to scroll
to Delete all old, then
press SELECT.
Delete all old
ECO
3
For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de blessures corporelles ou d’électrocution,
suivez toujours ces mesures préventives de base lorsque vous utilisez votre téléphone :
1. Lisez et comprenez bien toutes les instructions.
2. Observez toutes les instructions et mises en garde inscrites sur l’appareil.
3. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas
de nettoyeurs liquides ni en aérosol. N’utilisez qu’un chiffon doux et légèrement
humecté.
4. ATTENTION: Ne pas installer le socle téléphonique à une hauteur supérieure à 2
mètres.
5. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier
de cuisine, d’un bac de lavage ou d’une piscine, ou dans un sous-sol humide ou sous
la douche.
6. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil
pourrait tomber et être sérieusement endommagé.
7. Évitez d’installer le système téléphonique dans les endroits soumis à une température
extrême, à la lumière directe du soleil ou à proximité immédiate d’autres appareils
électriques ou électroniques. Protégez votre téléphone contre les sources
d’humidité, la poussière, les vapeurs et les liquides corrosifs.
8. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière
ou en dessous. Afin d’empêcher la surchauffe, ces ouvertures ne doivent pas être
obstruées en plaçant l’appareil sur un lit, divan, tapis ou autre surface similaires.
Ne placez pas cet appareil à proximité d’un élément de chauffage ni d’une plinthe
électrique. De plus, ne l’installez pas dans une unité murale ou un cabinet fermé
qui ne possède pas d’aération adéquate.
9. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les
étiquettes de l’appareil. Si vous ne connaissez pas le voltage de votre maison,
consultez votre marchand ou votre fournisseur d’électricité.
10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit
sécuritaire, là où personne ne pourra trébucher sur la ligne d’alimentation ni le
cordon téléphonique modulaire.
11. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils
pourraient toucher à des points de tension dangereux ou court-circuiter des pièces,
ce qui constituerait un risque d’incendie ou d’électrocution. N’échappez pas de
liquides dans l’appareil.
12. Afin de réduire les risques d’électrocution, ne démontez pas l’appareil, mais
apportez-le plutôt à un centre de service qualifié s’il doit être réparé. En enlevant
le couvercle, vous vous exposez à des tensions dangereuses ou autres dangers
similaires. Un remontage inadéquat peut être à l’origine d’une électrocution lors
d’une utilisation ultérieure de l’appareil. Débranchez l’appareil avant de procéder
au nettoyage. Utilisez un chiffon humide et doux.
13. Ne surchargez pas les prises de courant et les rallonges.
14. Débranchez cet appareil de la prise de courant et communiquez avec le
département de service à la clientèle de VTech dans les cas suivants :
• Lorsque le cordon d’alimentation est endommagé ou écorché.
• Si du liquide a été échappé dans l’appareil.
• Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.
• Si le produit ne fonctionne pas normalement en respectant les instructions de
fonctionnement. Réglez uniquement les commandes indiquées dans le les
instructions de fonctionnement. Les réglages incorrects des autres commandes
pourraient provoquer un dommage qui pourrait exiger un travail exhaustif de
la part d’un technicien autorisé afin de rétablir le fonctionnement normal de
l’appareil.
• Si le produit a été échappé et que le socle et/ou le combiné a été endommagé.
• Si le produit affiche une nette diminution de sa performance.
15. Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant un orage. Les éclairs
peuvent être à l’origine d’une électrocution.
16. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite.
En certaines circonstances, une flammèche pourrait être provoquée lorsque
l’adaptateur est branché à une prise de courant, ou lorsque le combiné est
déposé sur le socle. Ceci est un événement commun associé à la fermeture d’un
circuit électrique. L’utilisateur ne devrait pas brancher le téléphone à une prise de
courant, et ne devrait pas déposer le combiné chargé sur le socle, si le téléphone
se trouve à proximité d’un endroit comportant des concentrations de gaz
inflammables, à moins que la ventilation soit adéquate. Une flammèche dans un tel
endroit pourrait provoquer un incendie ou une explosion. De tels environnements
peuvent comprendre: des endroits où l’on utilise de l’oxygène médical sans
ventilation adéquate; des gaz industriels (dissolvants de nettoyage, des vapeurs
d’essence, etc.); une fuite de gaz naturel, etc.
17. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode
de conversation.
18. Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au
sol. Les broches ne sont pas conçues pour maintenir l’adaptateur en place si celui-ci
est barnché dans une prise au plafond ou sous une table/ armoire.
19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le socle de prise de courant
doit etre installe a proximite du materiel et doit etre aisement accessible.
20. MISE EN GARDE: Il peut y avoir un risque d’explosion si vous utilisez le
mauvais type de piles pour le téléphone. N’utilisez que les piles rechargeable inclus
ou les piles de rechange (BT162342/BT262342). N’incinérez pas les piles. Celles-ci
risqueraient d’exploser.
• Évite d’utiliser la batterie dans les conditions suivantes:
» des températures extrêmes faibles ou élevées auxquelles une batterie peut être
soumise pendant l’utilisation, le stockage ou le transport;
» Remplacement d’une batterie par un type incorrect pouvant supprimer une
protection;
» mise au rebut d’une batterie dans un feu ou dans un four chaud, ou écrasement
mécanique ou coupure d’une batterie, susceptible de provoquer une explosion;
» maintien d’une batterie dans un environnement à très haute température pouvant
provoquer une explosion ou la fuite de liquide ou de gaz inflammables;
» batterie soumise à une pression de l’air extrêmement faible pouvant provoquer
une explosion ou la fuite de liquide ou de gaz inflammables.
21. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur
dont la polarité ou la tension serait inadéquate risque d’endommager sérieusement
le produit et mettre votre sécurité en péril.
22. La plaque signalétique appliquée est située au bas ou à proximité du produit.
CONSERVEZ CES INSTRUCTIONS
Pile
• N’utilisez que la pile incluse ou l’équivalent. Pour commander une pile de recharge,
visitez notre site Web au www.vtechphones.com ou composez le 800-595-9511. Au
Canada, visitez le phones. phones.vtechcanada.com ou composez le 800-267-7377.
• Ne jetez pas la pile au feu. Vérifiez les instructions spécifiques de mise aux rebus
auprès des autorités locales.
• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif
et pourrait causer des brûlures ou des blessures aux yeux ou à la peau. L’électrolyte
est toxique si avalé.
• Soyez prudents lorsque vous manipulez les piles afin d’éviter les courts-circuits
provoqués par des matériaux conducteurs.
• Rechargez la pile incluse avec cet appareil, selon les instructions et limites spécifiées
dans ce guide d’utilisation.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans
fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche
indépendante, a mené une évaluation pluridisciplinaire des interférences entre les
téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans l’organisme.
Appuyée par l’Administration des aliments et drogues (FDA) des États-Unis, la firme
WTR recommande aux médecins :
Avis aux détenteurs de stimulateurs cardiaques
• Ils doivent tenir le téléphone sans fil à une distance d’au moins six pouces du
stimulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur
cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche.
• Ils doivent utiliser le téléphone sans fil en l’appuyant sur l’oreille qui se trouve dans
la direction opposée au stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs
de simulateurs cardiaques causés par les gens qui utilisent un téléphone sans fil à
proximité de ceux-ci.
À propos des téléphones sans fil
Confidentialité : Les mêmes caractéristiques qui constituent des avantages pour les
téléphones sans fil affichent également des restrictions. Les appels téléphoniques
sont transmis entre le combiné sans fil et le socle par le biais d’ondes radio ; il y a donc
la possibilité que vos conversations téléphoniques sans fil soient interceptées par des
équipements de réception radio se trouvant dans la portée du combiné sans fil. Pour
cette raison, vous ne devez pas percevoir les communications téléphoniques sans fil
comme étant aussi confidentielles que celles des téléphones à cordons.
Alimentation électrique : Le socle de ce téléphone sans fil doit être branché à une
prise électrique fonctionnelle. La prise électrique ne doit pas être contrôlée par un
interrupteur mural. Les appels ne pourront pas être effectués du combiné sans fil si le
socle est débranché ou mis hors tension ou si le courant est coupé.
Possibilité d’interférences aux téléviseurs : Certains téléphones sans fil fonctionnent
sur des fréquences pouvant causer des interférences aux téléviseurs et aux
magnétoscopes. Pour réduire ou prévenir de telles interférences, ne placez pas le
socle du téléphone sans fil près ou sur un téléviseur ou magnétoscope. S’il y a présence
de parasites, il est conseillé d’éloigner le téléphone sans fil du téléviseur ou du
magnétoscope afin de réduire possiblement les interférences.
Piles rechargeables : Manipulez les piles avec soin afin de ne pas les court-circuiter avec
des bagues, bracelets ou clés. Les piles ou le conducteur peut surchauffer et causer des
blessures. Respectez la polarité adéquate entre la pile et le chargeur.
Les bloc-piles rechargeables à l’hydrure métallique de nickel : Jetez ces blocs-piles de
manière écologique et sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les
autres piles de ce type, elles pourraient dégager une matière toxique qui peut causer
des blessures corporelles si elles sont brûlées ou percées.
The RBRC seal
The RBRC seal on the nickel-metal hydride battery indicates that VTech
Communications, Inc. is voluntarily participating in an industry program to
collect and recycle these batteries at the end of their useful lives, when
taken out of service within the United States and Canada.
The program provides a convenient alternative to placing used nickel-
metal hydride batteries into the trash or municipal waste, which may be
illegal in your area.
VTech’s participation makes it easy for you to drop off the spent battery at local retailers
participating in the RBRC program or at authorized VTech product service centers. Please
call 1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/
restrictions in your area. VTech’s involvement in this program is part of its commitment to
protecting our environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.
FCC, ACTA and IC regulations
FCC Part 15
NOTE: This equipment has been tested and found to comply with the requirements
for a Class B digital device under Part 15 of the Federal Communications Commission
(FCC) rules. These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved by
the party responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation. Privacy of communications may not be ensured when using this
telephone.
To ensure safety of users, the FCC/ISEDC has established criteria for the amount of radio
frequency energy that can be safely absorbed by a user or bystander according to the
intended usage of the product. This product has been tested and found to comply with
the FCC/ISEDC criteria. The handset may be safely held against the ear of the user. The
telephone base shall be installed and used such that parts of the user’s body other than
the hands are maintained at a distance of approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements
adopted by the Administrative Council for Terminal Attachments (ACTA). The label
on the back or bottom of this equipment contains, among other things, a product
identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your
telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the
telephone network must comply with applicable Part 68 rules and technical
requirements adopted by ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to a compatible modular
jack that is also compliant. An RJ11 jack should normally be used for connecting to a
single line. See the installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you
may connect to your telephone line and still have them ring when you are called.
The REN for this product is encoded as the 6th and 7th characters following the US:
in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the
sum of all RENs should be five (5.0) or less. For more information, please contact your
telephone service provider.
This equipment must not be used with Party Lines. If you have specially wired alarm
dialing equipment connected to your telephone line, ensure the connection of this
equipment does not disable your alarm equipment. If you have questions about what
will disable alarm equipment, consult your telephone service provider or a qualified
installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until
the problem has been corrected. Replacement to this telephone equipment can only
be made by the manufacturer or its authorized agents. For replacement procedures,
follow the instructions outlined under the Limited warranty.
If this equipment is causing harm to the telephone network, the telephone service
provider may temporarily discontinue your telephone service. The telephone service
provider is required to notify you before interrupting service. If advance notice is not
practical, you will be notified as soon as possible. You will be given the opportunity to
correct the problem and the telephone service provider is required to inform you of
your right to file a complaint with the FCC. Your telephone service provider may make
changes in its facilities, equipment, operation, or procedures that could affect the
proper functioning of this product. The telephone service provider is required to notify
you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid
compatible.
If this product has memory dialing locations, you may choose to store emergency
telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test
emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Privacy of communications may not be ensured when using this telephone.
The term ‘’IC:‘’ before the certification/registration number only signifies that the
Industry Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 1.0. The REN
indicates the maximum number of devices allowed to be connected to a telephone
interface. The termination of an interface may consist of any combination of devices
subject only to the requirement that the sum of the RENs of all the devices not exceed
five.
This product meets the applicable Innovation, Science and Economic Development
Canada technical specifications.
California Energy Commission battery
charging testing instructions
This telephone is set up to comply with the energy-conserving standards right out of the
box. These instructions are intended for California Energy Commission (CEC) compliance
testing only. When the CEC battery charging testing mode is activated, all telephone
functions, except battery charging, will be disabled.
To activate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power outlet. Make sure all
handsets are plugged with charged batteries before proceeding.
2. While you press and hold /FIND HS, plug the telephone base power adapter back
to the power outlet.
3. After about 20 seconds, when the HOME light starts flashing, release /FIND HS and
then press it again within two seconds. You hear a confirmation tone. The HOME light
turns off and all handsets display To register HS... see manual alternately. Allow up to
one minute for the process to complete.
If the phone fails to enter this mode, repeat all the steps mentioned above. The
telephone base will be powered up as normal if you fail to press /FIND HS within two
seconds in Step 3.
To deactivate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power outlet, and then plug it
back in. Then the telephone base is powered up as normal.
2. Put the handsets on the telephone base cradle to begin registration.
3. The handset shows Registering... If the registration is successful, the handset screen
displays Registered and beeps. The handset is registered with the telephone base.
Limited Warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase
(“Consumer” or “you”) that the Product and all accessories provided in the sales package
(“Product”) are free from defects in material and workmanship, pursuant to the following
terms and conditions, when installed and used normally and in accordance with the
Product operating instructions. This limited warranty extends only to the Consumer for
Products purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and
workmanship during the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will
replace at VTech’s option, without charge, a Materially Defective Product. If we replace
the Product, we may use new or refurbished replacement parts. If we choose to replace
the Product, we may replace it with a new or refurbished Product of the same or similar
design. We will retain defective parts, modules, or equipment. Replacement of the
Product, at VTech’s option, is your exclusive remedy. VTech will return the replacement
Products to you in working condition. You should expect the replacement to take
approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of
purchase. If VTech replaces a Materially Defective Product under the terms of this limited
warranty, this limited warranty also applies to the replacement Product for a period of
either (a) 90 days from the date the replacement Product is shipped to you or (b) the
time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical
damage, improper installation, abnormal operation or handling, neglect,
inundation, fire, water or other liquid intrusion.
2. Product that has been subjected to contact with liquid, water, rain, extreme
humidity or heavy perspiration, sand, dirt or the like; but then only to the extent
the damage was not caused by incorrectly securing the waterproof handset’s
protective elements, for example, failing to properly close a seal), or such
protective elements are damaged or missing (e.g. a cracked battery door), or
subjecting a Product to conditions beyond its stated specifications or limits (e.g. 30
minutes in 1 meter of fresh water).
3. Product that has been damaged due to repair, alteration or modification by
anyone other than an authorized service representative of VTech;
4. Product to the extent that the problem experienced is caused by signal conditions,
network reliability, or cable or antenna systems;
5. Product to the extent that the problem is caused by use with non-VTech
accessories;
6. Product whose warranty/quality stickers, product serial number plates or electronic
serial numbers have been removed, altered or rendered illegible;
7. Product purchased, used, serviced, or shipped for repair from outside the United
States of America or Canada, or used for commercial or institutional purposes
(including but not limited to Products used for rental purposes);
8. Product returned without a valid proof of purchase (see item 2 below); or
9. Charges for installation or set up, adjustment of customer controls, and installation
or repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the United States of America, please visit our website at
www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to
phones.vtechcanada.com or dial 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s
controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during
transit and transportation and are responsible for delivery or handling charges incurred
in the transport of the Product(s) to the service location. VTech will return replaced
Product under this limited warranty. Transportation, delivery or handling charges are
prepaid.
VTech assumes no risk for damage or loss of the Product in transit. If the Product failure
is not covered by this limited warranty, or proof of purchase does not meet the terms
of this limited warranty, VTech will notify you and will request that you authorize the
cost of replacement prior to any further replacement activity. You must pay for the cost
of replacement and return shipping costs for the replacement of Products that are not
covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech
service location along with a description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying the Product
purchased (Product model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone
number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It
supersedes all other written or oral communications related to this Product. VTech
provides no other warranties for this Product. The warranty exclusively describes all of
VTech’s responsibilities regarding the Product. There are no other express warranties.
No one is authorized to make modifications to this limited warranty and you should not
rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may
also have other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and
merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited
to one year from the date of purchase. Some states/provinces do not allow limitations
on how long an implied warranty lasts, so the above limitation may not apply to you.
In no event shall VTech be liable for any indirect, special, incidental, consequential, or
similar damages (including, but not limited to lost profits or revenue, inability to use the
Product or other associated equipment, the cost of substitute equipment, and claims
by third parties) resulting from the use of this Product. Some states/provinces do not
allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase
Disclaimer and Limitation of Liability
VTech Communications, Inc. and its suppliers assume no responsibility for any damage
or loss resulting from the use of this user’s manual. VTech Communications, Inc. and its
suppliers assume no responsibility for any loss or claims by third parties that may arise
through the use of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States
Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada
Delete entry?
ECO
1
2
Press SELECT.
LCD language setting
If you accidentally set the LCD language to Spanish
or French, you can change the LCD language back to
English while the telephone is not in use:
• On the telephone base, press MENU and then enter
364#.
• On the handset, press MENU and then enter 364#.
You can set the answering system to answer an incoming call
after 2, 3, 4, 5 or 6 rings; or Toll saver.
If you choose Toll saver, the answering system answers a call
after two rings when you have new messages, or after four
rings when you have no new messages. This enables you to
check for new messages and avoid paying unnecessary long
distance charges if you are calling from outside your local area.
NOTE
-
1
-
2
VTech VS306-4 Guide de démarrage rapide
- Catégorie
- Téléphones
- Taper
- Guide de démarrage rapide
dans d''autres langues
- English: VTech VS306-4 Quick start guide
Documents connexes
-
VTech IS8129 Manuel utilisateur
-
VTech IS8128-4 Guide de démarrage rapide
-
VTech VS113-5 Mode d'emploi
-
-
-
-
-
-
VTech IS8121 Mode d'emploi