GE GXSH40V Le manuel du propriétaire

WATER SOFTENING

SYSTEM

Safety Information ............. 2

Specifications

and Performance Claims ........ 3

About the Softener ............ 4

Before you Start ............... 7

Installation Requirements ....... 8

Installation Instructions .........11

Programming the Softener ......16

Care and Cleaning ............ 22

Routine Maintenance ..........24

Before you call for Service ..... 25

Exploded View/Parts List .......31

Warranty (U.S.) ............... 35

Warranty (Canada) ........... 36

Consumer Support ............40

7386415 49-6000299 Rev. 0 11-23

Write the model and

serial numbers here:

Model # _____________

Serial # _____________

To find these numbers,

lift the cover and look

on the rim below the

control panel.

Model GXSH40V,

GXSH45V

GE is a trademark of the General Electric Company. Manufactured under trademark license.

OWNER’S MANUAL

AND INSTALLATION

INSTRUCTIONS

Systems tested and certified by NSF International

against NSF/ANSI Standard 44 and certified to

NSF/ANSI/CAN 372.

Systems Tested and Certified by the Water Quality

Association against CSA B483.1.

If you have any questions or concerns when installing or maintaining

your water softener, call our toll free number at 800-952-5039 (US)

or 866-777-7627 (Canada), or visit GEAppliances.com. When you

call, please be prepared to provide the model and serial number

of your product. This information can be found on the rating decal

located on the rim under the salt cover.

CUS

R

ENGLISH/FRANÇAIS/

ESPAÑOL

2

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING

SAFETY PRECAUTIONS

WARNING

A copper or

galvanized cold water pipe may be used to

ground electrical outlets in the home. Failure to

maintain this ground path may result in an

electric shock hazard. If the cold water pipe is

used to ground electric outlets, please refer to

Installing the Ground Wire section before

cutting the pipe.

 Check and comply with your state and local

codes. You must follow these guidelines.

 Use care when handling the water softening

system. Do not turn upside down, drop, drag

or set on sharp protrusions.

 Water softening systems using sodium

chloride (salt) for recharge add sodium to the

water.

Persons on sodium restricted diets should

consider the added sodium as part of their

overall intake. Potassium chloride can be

used as an alternative to sodium chloride in

your softener.

 Use only lead-free solder and flux for all

sweat-solder connections, as required by

state and federal codes.

 This water softening system must be properly

installed and located in accordance with the

installation instructions before it is used.

 Keep the salt hole cover in place on the

softener unless servicing the unit or refilling

with salt.

WARNING

Do not use with

water that is microbiologically unsafe or of

unknown quality without adequate disinfection

before or after the system.

WARNING

Discard all unused

parts and packaging material after installation.

Small parts remaining after the installation

could be a choke hazard.



The water softening system works on 24 volt-

60 Hz

electrical power only. Be sure to use

the included external power supply.

 External power supply must be plugged into

an indoor 120 volt, grounded outlet only.

 Use clean water softening salts only, at least

99.5% pure. NUGGET, PELLET or coarse

SOLAR salts are recommended. Do not use

rock, block, granulated or ice cream making

salts. These types of salts may contain dirt

and sediments that might mush or cake,

creating maintenance issues for the water

softener.

 Avoid installing in direct sunlight. Excessive

heat may cause distortion or other damage

to non-metallic parts.

 If installing the water softener outdoors, do

not locate where it will be exposed to wet

weather, direct sunlight, extreme hot or cold

temperatures, or other forms of abuse.

WARNING

For your safety, the information in this manual must be followed to

minimize the risk of electric shock, property damage or personal injury.

In the state of California: You must turn

the Salt Efficiency Feature setting to ON.

This may initiate more frequent recharges.

However it will operate at 4,000 grains per

pound of salt or higher. To turn on the Salt

Efficiency Feature, follow the instructions in

the “Salt Saver” section of this manual.

In the Commonwealth of Massachusetts,

Plumbing Code 248 CMR shall be adhered

to. Consult with your licensed plumber.

READ AND SAVE THESE INSTRUCTIONS

3

Specifications

Model GXSH40V GXSH45V

Rated Capacity* (Grains@ Salt Dose) 11,700 @ 2.3 lbs

31,500 @ 8.7 lbs.

40,000 @ 15.1 lbs.

13,200 @ 2.6 lbs

35,500 @ 9.9 lbs.

45,100 @ 17.0 lbs.

Rated Efficiency** (Grains/Pound of Salt @ Minimum Salt Dose) 5,090 @ 2.3 lbs. 5,050 @ 2.6 lbs.

Water used during Regeneration (gallons/grains) 2.7 /1000 2.8 /1000

Total Water Used per Regeneration @ Maximum Salt Dose 37.0 gallons 43.0 gallons

Amount of High Capacity Ion Exchange Resin (lb/cu.ft.) 57.56/1.11 65.0/1.25

Resin Tank Nominal Size (in., dia. x height) 9 x 40 10 x 40

Service Flow Rate (gpm) 9.5 9.5

Pressure Drop at Rated Service Flow (psig) 12.7 10.3

Water Supply Maximum Hardness (gpg) 110 160

Water Supply Maximum Clear Water Iron (ppm)*** 8 10

Water Pressure Limits (minimum-maximum psi)**** 20-125 20-125

Water Temperature Limits (minimum-max. °F) 40-120 40-120

Maximum Flow Rate to Drain (gpm) 2.3 2.3

Specifications and Performance Claims

These systems conform to NSF/ANSI 44 for

the specific capacity claims as verified and

substantiated by test data.

* Testing was performed using pellet grade

sodium chloride as

the regenerant salt.

** Efficiency rating is valid only at the lowest

stated salt dosage. These softeners were

efficiency rated according to NSF/ANSI 44.

*** Extent of iron removal may vary with

conditions. The capacity to reduce clear

water iron is substantiated by WQA test data.

State of Wisconsin requires additional treatment if water supply contains greater than 5 ppm clear water iron.

Refer to Cleaning Iron Out of the Water Softening System section.

**** Canada working pressure limits: 1.4–7.0 kg/cm2.

This model is efficiency rated. The efficiency rating is valid only at the minimum stated salt dose. The softener has

a demand initiated regeneration (D.I.R) feature that complies with specific performance specifications intended to

minimize the amount of regenerant brine and water used in its operation.

The softener has a rated salt efficiency of not less than 4,000 grains of total hardness exchange per pound of

salt (based on sodium chloride), and shall not deliver more salt than its listed rating or be operated at a sustained

maximum service flow rate greater than its listed rating. This softener has been proven to deliver soft water for at

least ten continuous minutes at the rated service flow rate. The rated salt efficiency is measured by laboratory test

described in NSF/ANSI Standard 44. These tests represent the maximum possible efficiency that the system can

achieve. Operational efficiency is the actual efficiency after the system has been installed. It is typically less than the

efficiency, due to individual application factors including water hardness, water usage, and other contaminants that

reduce the softener’s capacity.

Performance Claims

Contaminant Influent

Challenge

Level

Maximum

Allowable Product

Water Level

Barium 10 ±10% mg/L 2.0 mg/L

Radium 226/228 25 pCi/L 5pCi/L

Test parameters include: pH = 7.5±0.5, flow rate = 7.5 gpm

and dynamic pressure = 35±5 psig

4

SERVICE

When the water softening system is providing

soft water, it is called “Service.” During service,

hard water flows from the house main water

pipe into the water softening system. Inside the

water softening system resin tank is a bed made

up of thousands of tiny, plastic resin beads. As

hard water passes through the bed, each bead

attracts and holds the hard minerals. This is

called ion-exchanging. It is much like a magnet

attracting and holding metals. Water without

hard minerals (soft water) flows from the water

softening system and to the house pipes.

After a period of time, the resin beads become

coated with hard minerals and they have to

be cleaned. This cleaning is called recharge.

Recharge is started at 2:00 AM (factory setting)

by the water softening system control, and

consists of five stages or cycles. These are

FILL, BRINING, BRINE RINSE, BACKWASH

and FAST RINSE.

AUTOMATIC HARD WATER BYPASS DURING RECHARGE

During recharge the water softener is

automatically put in bypass mode allowing hard

water to be available to the home. Once the

softener is recharged water is directed back

through the softener to be conditioned.

However, you should avoid using HOT water

because the water heater will fill with the

hard water.

FILL

Salt dissolved in water is called brine. Brine is

needed to clean the hard minerals from resin

beads. To make the brine, water flows into the

salt storage area during the fill stage.

BRINING

During brining, brine travels from the salt

storage area into the resin tank. Brine is the

cleaning agent needed to remove hard minerals

from the resin beads. The hard minerals and

brine are discharged to the drain.

The nozzle and venturi create a suction to

move the brine, maintaining a very slow rate to

get the best resin cleaning with the least salt.

BRINE RINSE

After a pre-measured amount of brine is used,

the brine valve closes. Water continues to flow

in the same path as during brining, except for

the discontinued brine flow. Hard minerals and

brine flush from the resin tank to the drain.

BACKWASH

During backwash, water travels up through

the resin tank at a fast flow rate, flushing

accumulated iron, dirt and sediments from the

resin bed and to the drain.

FAST RINSE

Backwash is followed by a fast flow of water

down through the resin tank. The fast flow

flushes brine from the bottom of the tank, and

packs the resin bed.

After fast rinse, the water softening system

returns to soft water service.

About the water softener system

5

FEATURE: OPTIONAL RECHARGE CONTROLS

Sometimes, a manually started recharge may

be desired or needed. Two examples:

 You have used more water than usual

(house guests, extra washing, etc.) and you

may run out of soft water before the next

recharge.

 The system ran out of salt.

Use one of the following features to start a

recharge immediately, or at the next preset

recharge start time.

RECHARGE TONIGHT

Touch (do not hold) the RECHARGE button.

RECHARGE TONIGHT flashes in the control

display area. A recharge will occur at the next

preset recharge start time. If you decide to

cancel this recharge, touch the same button

once more.

RECHARGE NOW

Press and hold the RECHARGE button until

RECHARGE NOW starts to flash in the control

display area. The water softening system

begins an immediate recharge and, when over

in about two hours, you will have a new supply

of soft water. Once started, you cannot cancel

this recharge.

FEATURE: MEMORY

If electrical power to the water softening system

is interrupted, the control display is blank, and

the blue indicator light is off, but the control

keeps correct time for 24 hours. When power

is restored, you have to reset the present time

only if the display and blue indicator light are

flashing. All other settings are maintained and

never require resetting unless a change is

desired.

If the time is flashing after a long power outage,

the water softening system continues to work

as it should to provide you with soft water.

However, recharge may occur at the wrong

time of day until you reset the control to the

correct time of day.

FEATURE/SERVICE: AUTOMATIC ELECTRONIC DIAGNOSIS

The control computer has a self-diagnostic

function for the electrical system (except

input power and water meter). The computer

monitors the electronic components and circuits

for correct operation. If a malfunction occurs,

an error code appears in the control display.

NORMAL OPERATION, CONTROL DISPLAYS

During normal operation, the present time of

day and AM or PM and DAYS TO EMPTY

show in the control display area.

The system will automatically recharge at the

preset recharge time as needed.

About the water softener system

6

WATER CONDITION INFORMATION

IRON

Iron in water can cause stains on clothing

and plumbing fixtures. It can negatively affect

the taste of food,drinking water, and other

beverages. Iron in water is measured in parts

per million (ppm). The total* ppm of iron, and

type or types*, is determined by chemical

analysis. Four different types of iron in water

are:

 Ferrous (clear water) iron

 Ferric (red water) iron



Bacterial and organically bound iron

 Colloidal and inorganically bound iron

(ferrous or ferric)

Ferrous (clear water) iron is soluble and

dissolves in water. This water softener will

reduce moderate amounts of this type of iron

(see specifications).**Ferrous (clear water)

iron is usually detected by taking a sample of

water in a clear bottle or glass. Immediately

after taking, the sample is clear. As the water

sample stands, it gradually clouds and turns

slightly yellow or brown as air oxidizes the iron.

This usually occurs in 15 to 30 minutes.

When using the softener to reduce Ferrous

(clear water) iron, add 5 grains to the hardness

setting fore very 1 ppm of Ferrous (clear

water) iron. See “Set Water Hardness Number”

section.

Ferric (red water), and bacterial and organically

bound irons are insoluble. This water softener

will not remove ferric or bacterial iron. This

iron is visible immediately when drawn from a

faucet because it has oxidized before reaching

the home. It appears as small cloudy yellow,

orange, or reddish suspended particles. After

the water stands for a period of time,the

particles settle to the bottom of the container.

Generally these irons are removed from water

by filtration. Chlorination is also recommended

for bacterial iron.

Colloidal and inorganically bound iron is of

ferric or ferrous form that will not filter or

exchange out of water. This water softener will

not remove colloidal iron. In some instances,

treatment may improve colloidal iron water.

Colloidal iron water usually has a yellow

appearance when drawn. After standing for

several hours, the color persists and the iron

does not settle,but remains suspended in the

water.

SEDIMENT FILTER (BUILT IN)

Sediment is fine, foreign material particles

suspended in water. This material is most

often clay or silt. Extreme amounts of sediment

may give the water a cloudy appearance. The

built in sediment filter keeps larger particles

of sediment from entering the home plumbing

system. As water passes through the softener,

the larger sediment particles are collected in

the integrated basket and then rinsed to the

drain before each regeneration. The sediment

filter feature provides added protection for

water using appliances by reducing the chance

of larger particles entering the various products

valves and screens.

IMPORTANT: The sediment filter is not intended

to replace pretreatment filtration. For problem

water applications, additional sediment filtration

is recommended.

CHLORINE

Softener resins may degrade in the presence

of chlorine above 2 ppm. If you have chlorine

in excess of this amount, you may experience

reduced life of the resin. In these conditions, you

may wish to consider purchasing a GE Appliances

point-of-entry household filtration system with a

chlorine reducing filter.

* Water may contain one or more of the four

types of iron and any combination of these.

Total iron is the sum of the contents.

** Capacity to reduce clear water iron is

substantiated by WQA test data.

About the water softener system

7

Bypass Valve Drain Hose Clips Installation

Adaptors

Hose Clamps Overflow

Adapter Grommet O-rings Silicone

Grease

BEFORE YOU START

 The water softener requires a minimum water flow of 3 gallons per minute at the inlet. Maximum

allowable inlet water pressure is 125 psi. If daytime pressure is over 80 psi, nighttime pressure

may exceed the maximum. Use a pressure reducing valve if necessary (Adding a pressure

reducing valve may reduce the flow). If your home is equipped with a back flow preventer, an

expansion tank must be installed in accordance with local codes and laws.

 The water softener uses a direct plug-in external power supply (included). Be sure to use the

included power supply and plug it into a nominal 120V, 60 cycle household outlet that is in a

dry location only, grounded and properly protected by an over current device such as a circuit

breaker or fuse.

 Do not use this system to treat water that is microbiologically unsafe or of unknown quality

without adequate disinfection upstream or downstream of the system.

INSPECT SHIPMENT

Make sure all the parts shown below are present. Additional parts must be purchased to complete

the installation. Thoroughly check the water softener for possible shipping damage and parts loss.

Also inspect and note any damage to the shipping carton.

Remove and discard (or recycle) all packing materials. To avoid loss of small parts, we suggest

you keep the small parts in the parts bag until you are ready to use them.

WARNING

Discard all unused parts and packaging material after installation.

Small parts remaining after the installation could be a choke hazard.

TOOLS AND MATERIALS REQUIRED FOR INSTALLATION

 Pliers

 Screwdriver

 Razor knife

 Two adjustable wrenches

 Teflon tape

 2 fittings to connect household plumbing to

1” NPT threads on softening adaptors.

 Additional installation parts may be required:

• UL-approved grounding clamps and

6-gauge copper grounding wire.

NOTE: Failure to comply with these installation instructions will void the product warranty,

and the installer will be responsible for any service, repair or damages caused thereby.

Before you start

8

IN

OUT

3-3/4"

TOP VIEW

FRONT VIEW SIDE VIEW

14-7/16"

22-7/16"

47-5/8"

41-1/2"

IN - OUT

LOCATION REQUIREMENTS

Consider all of the following when selecting an

installation location for the water softener.

 Do not locate the water softener where freezing

temperatures occur. Do not attempt to treat

water over 120ºF. Freezing temperatures or

hot water damage voids the warranty.

 To condition all water in the home, install

the water softener close to the water supply

inlet, and upstream of all other plumbing

connections, except outside water pipes.

Outside faucets should remain on hard water

to avoid wasting conditioned water and salt.

 A nearby drain is needed to carry away regeneration

discharge (drain) water. Use a floor drain,laundry

tub, sump, standpipe, or other options(check your

local codes). See “Air Gap Requirements” and

“Valve Drain Requirements”sections.

 The water softener uses a direct plug-in external

power supply (included). Be sure to use the included

power supply and plug it into a nominal 120V, 60

cycle household outlet that is in a dry location only,

grounded and properly protected by an over current

device such as a circuit breaker or fuse.

 Always install the water softener between

the water inlet and water heater. Any other

installed water conditioning equipment should

be installed between the water inlet and

water softener (See Figure below).

 If installing the water softener outdoors, do

not locate where it will be exposed to wet

weather, direct sunlight, extreme hot or cold

temperatures, or other forms of abuse.

 DO NOT RUN HOT WATER THROUGH THE

SOFTENER. Temperature of water passing

through the softener must be less than 120° F.

 Avoid installing in direct sunlight. Excessive

sun heat may cause distortion or other

damage to non-metallic parts.

 When installing in an outside location you

must take steps necessary to assure the

softener, installation plumbing and wiring, are

protected from the elements, direct sunlight,

contamination, vandalism, insects, vermin, etc.

 Do not install the softener where it would block

access to the water heater or access to the

main water shutoff.

DIMENSIONS

Installation Requirements

PROPER ORDER TO INSTALL WATER TREATMENT EQUIPMENT

Well

Pump

Well Water Supply

City Water Supply

OR

Pressure

Tank

Optional

Sediment

Filter

Water

Heater Water

Softener

Hot Water to House

Cold Water to House

Untreated Water to

Outside Faucets Shut off

valve

9

PLUMBING CODES

All plumbing must be completed in accordance

with national, state and local plumbing codes.

In the state of Massachusetts: The

Commonwealth of Massachusetts plumbing

code 248-CMR shall be adhered to. A licensed

plumber shall be used for this installation.

AIR GAP REQUIREMENTS

A drain is needed for regeneration water (See

Figure 1). A floor drain, close to the water

softener, is preferred. A laundry tub, standpipe,

etc. are other drain options. Secure valve

drain hose in place. Leave an air gap of 1-1/2”

between the end of the hose and the drain. This

gap is needed to prevent back flow of sewer

water into the water softener. Do not put the

end of the drain hose into the drain.

VALVE DRAIN REQUIREMENTS

Using the flexible drain hose (included) (See

Figure 2), measure and cut to the length

needed. Flexible drain hose is not allowed in all

localities (check your plumbing codes). If local

codes do not allow use of a flexible drain hose,

a rigid valve drain run must be used. Purchase

a compression fitting (1/4 NPT x 1/2 in.

minimum tube) and 1/2” tubing from your local

hardware store. Plumb a rigid drain as needed

(See Figure 3).

NOTE: Avoid drain hose runs longer than 30

feet. Avoid elevating the hose more than 8 feet

above the floor. Make the valve drain line as

short and direct as possible.

FLEXIBLE DRAIN LINE

RIGID DRAIN LINE

FLOOR

DRAIN STANDPIPE LAUNDRY

TUB

1-1/2”

air gap

1-1/2”

air gap

1-1/2”

air gap

Drain

Hose Drain

Hose

Drain

Hose

Figure 1

Figure 3

Clip 1/4Ǝ NPT thread

ƎRXWVLGH

diameter

copper tube

(not provided)

Compression fitting

137[Ǝ2'

tube (not provided)

Cut barbs from valve drain

elbow (pull clip and remove

drain valve elbow from valve)

Barbs

Barbs for 3/8

Ǝ

I.D. tubing

Hose clamp

Drain hose

1/4” NPT Thread

Figure 2

Drain hose adapter

Installation Requirements

10

INLET/OUTLET PLUMBING

REQUIREMENTS

Always install either a single bypass valve

(provided),as shown in Figure 4, or, if desired,

parts for a 3 valve bypass system (not

included) can be purchased and assembled, as

shown in Figure 5. Bypass valves allow you to

turn off water to the softener for maintenance if

needed, but still have water in house pipes.

Pipe fittings must be 1/2” minimum.

Use:

 Copper pipe

 Threaded pipe

 PEX (Crosslinked Polyethylene) pipe

 CPVC plastic pipe

 Other pipe approved for use with potable

water

IMPORTANT: Do not solder with plumbing

attached to installation adaptors and single

bypass valve. Soldering heat will damage the

adaptors and valve.

WARNING

A copper or

galvanized cold water pipe may be used to

ground electrical outlets in the home. Failure to

maintain this ground path may result in an

electric shock hazard. If the cold water pipe is

used to ground electric outlets, please refer to

Installing the Ground Wire section before

cutting the pipe.

3-VALVE BYPASS SYSTEM

For soft water service: Open the inlet and

outlet valves and close the bypass valve.

For bypass hard water: Close the inlet and

outlet valves and open the bypass valve.

Installation Requirements

3 VALVE BYPASS

Bypass

Valve

Outlet

Valve Inlet

Valve

From Water

Softener To Water

Softener

Figure 5

SINGLE BYPASS VALVE

Pull out for “Service”

(Soft water)

Push in for

“Bypass”

Figure 4

Installation

adaptors

11

Clips

Inlet

Outlet

Lubricated

O-ring Single Bypass

Valve

O-ring

1” NPTM

Threaded

Adaptor

1” NPTF

Sweat

Adaptor

(not

included)

Pipe

1-1/2”

air gap

Floor Drain

Secure Valve Drain

Hose in place over Floor

Drain

Brine Tank

Overflow Hose*

Overflow

Adapter

Ground Clamp

Conditioned

Water

Main Water Pipe

Bypass Valve

Assembly

Plug-in

Transformer

To

Controller

Drain Hose

Adapter

Valve Drain

Hose*

*Do not connect the water

softener valve drain hose to

the brine tank overflow NOTE: See “Air Gap Requirements”

section.

NOTE: Be sure the turbine and support are firmly in place

in the valve outlet. Blow into the valve port and observe the

turbine for free rotation.

Figure 6

Figure 7

Incoming-

Hard Water

to Outside

Faucets

Top

Cover

Brine Tank

(Salt Storage)

Clips

• Remove plastic shipping plug and wire from valve outlet.

Figure 8

Turbine

Valve outlet

Turbine shaft and support

Plastic shipping plug

Ground Wire

(not included)

Clamp

(not included)

TYPICAL INSTALLATION

Installation Instructions

12

TURN OFF WATER SUPPLY

1. Close the main water supply valve, located

near the well pump or water meter.

2. Open all faucets to drain all water from

house pipes.

NOTE: Be sure not to drain water from the

water heater, as damage to the water heater

elements could result.

INSTALL BRINE TANK OVERFLOW ADAPTER

Install the brine tank overflow grommet and

adapter in the 13/16” diameter hole in the back

of the salt storage tank sidewall, (see Figure 9).

NOTE: The brine tank overflow adapter accepts

either 1/2” or 3/8” I.D. hose.

INSTALL THE BYPASS VALVE

NOTE: For easier installation, remove the top

cover. Release 2 clips at rear of cover. Rotate

cover forward and lift up.

1. Remove two clips from the water softener

valve inlet and outlet ports and visually check

and remove any debris, (see Figure 7).

2. Make sure the turbine assembly spins freely

in the”out” port of the valve, (see Figure 8).

3. If not already done, put a light coating of

silicone grease (provided) on the single

bypass valve o-rings, (see Figure 7).

4. Push the single bypass valve into the

softener valve as far as it will go. Snap the

two large holding clips into place, from the

top down, (see Figure 7 and 10).

IMPORTANT: Be sure the clips snap firmly into

place so the single bypass valve will not pull out.

MOVE WATER SOFTENER INTO PLACE

WARNING

Excessive Weight

Hazard

Use two or more people to move and install

water softener. Failure to do so can result in

back or other injury.

1. Move the water softener into the desired

location. Set it on a solid, level surface.

IMPORTANT: Do not place shims directly

under the salt storage tank to level the softener.

The weight of the tank, when full of water and

salt, may cause the tank to fracture at the shim.

CORRECT ASSEMBLY

Outside diameter

of clip channel on

single bypass valve

Clip

Outside diameter of

water softener valve

inlet & outlet

NOTE: Be sure all 3 tabs of the clip go through

the matching holes on the water softener valve

inlet or outlet, and fully into the channel on the

single bypass valve. Make sure that the tabs

are fully seated.

Figure 10

SINGLE BYPASS VALVE

If connecting to floor

level plumbing, install

the bypass valve turned

downward, as shown.

NOTE: Unit is shown with top cover removed.

Installation Instructions

Salt

Cover

Brinewell

Cover

Salt

Storage

Tank

Brinewell

Brine

Tubing

Brine Tank

Overflow

Elbow

Grommet

Hole

Nut - Ferrule

Nozzle Venturi

Assembly

Figure 9

Brine

Valve

13

COMPLETE INLET AND OUTLET

PLUMBING

WARNING

A copper or

galvanized cold water pipe may be used to

ground electrical outlets in the home. Failure to

maintain this ground path may result in an

electric shock hazard. If the cold water pipe is

used to ground electric outlets, please refer to

Installing the Ground Wire section before

cutting the pipe.

IMPORTANT: This water softener has a non-

metallic valve system. Installing it on metal

plumbing will break electrical continuity, which

may interrupt grounding for the home. You

must restore electrical continuity in your metal

plumbing system.

If you install a 3-valve bypass system (Figure

5), electrical continuity will be maintained. If you

install the non-metallic bypass valve (Figure

11), please refer to the Installing the Ground

Wire section before cutting the pipe.

Measure, cut, and loosely assemble pipe and

fittings from the main water pipe to the inlet

and outlet ports of the water softener valve. Be

sure to keep fittings fully together, and pipes

squared and straight.

BE SURE INCOMING HARD WATER SUPPLY

IS DIRECTED TO THE SOFTENER VALVE

INLET PORT.

NOTE: Inlet and outlet are marked on the water

softener valve. Trace the water flow direction to

be sure hard water is to inlet.

IMPORTANT: Be sure to fit, align and support

all plumbing to prevent putting stress on the

water softener valve inlet and outlet. Stress

from misaligned or unsupported plumbing may

cause damage to the valve.

• If making a soldered copper installation, do all

sweat soldering before connecting pipes to

the NPT adapters and bypass valve. Torch

heat will damage plastic parts.

WARNING

If solder is used to

make pipe connection use only lead free

solder and flux to prevent lead poisoning.

• When turning threaded pipe fittings onto

plastic fittings, use care not to cross-thread.

• Use Teflon Tape on all external pipe threads.

Complete the inlet and outlet plumbing for the

type of pipe you will be using. Secure ground

clamp to metal pipes.

INSTALLING THE GROUND WIRE

NOTE: If your house plumbing is plastic, it

would not be used as a grounding path, and

this step should be skipped.

IMPORTANT: A copper or galvanized cold

water pipe is often used to ground electrical

outlets in the home. Grounding protects you

from electrical shock. The water softener

may have broken this ground path. To restore

connection, install a 12”-long, 6-gauge

copper wire across and tightly clamp using

UL-approved 1/2”–1” bronze grounding clamps

at both ends as shown (Figure 12). Zinc clamps

should not be used on copper plumbing. Wire

and clamps may be purchased separately from

your local hardware store.

1.

Clean copper pipe and ends of wire with emery

paper. Bare wire is recommended. If insulated

wire is used, is should be stripped 3/4” at each

end before cleaning with emery paper.

2. Attach bronze clamps to pipe. Tighten screws.

3. Attach to clamps as shown. Tighten screws.

NOTE: If you are installing a sediment filter or

other item(s) into the plumbing system, along

with the water softener, be sure to restore

electrical continuity across all removed metal

pipe sections.

Figure 11

Figure 12

Ground Wire

Clamp (2)

Installation Instructions

14

INSTALL VALVE DRAIN HOSE

1. Measure and connect the 3/8”drain line

(provided) to the water softener valve drain

fitting. Use a hose clamp to hold the hose in

place.

NOTE: Avoid drain hose runs longer than 30

feet. Avoid elevating the hose more than 8 feet

above the floor. Make the valve drain line as

short and direct as possible.

IMPORTANT: If codes require a rigid drain line

see “Valve Drain requirements” section.

2. Route the drain hose or copper tubing

to the floor drain or other suitable drain

point. Secure drain hose. This will prevent

“whipping’’ during regenerations. See “Air

Gap Requirements” section (Figure 1).

3. Cut and secure the hose.

NOTE: The softener will not work if the water

cannot exit the drain hose during recharge.

INSTALL BRINE TANK (SALT

STORAGE) OVERFlOW HOSE

1. Measure, cut to needed length and connect

the 3/8”drain line (provided) to the salt

storage tank overflow elbow and secure in

place with a hose clamp.

2. Route the hose to the floor drain, or other

suitable drain point no higher than the drain

fitting on the salt storage tank (This is a

gravity drain). If the tank overfills with water,

the excess water flows to the drain point. Cut

the drain line to the desired length and route

it neatly out of the way.

IMPORTANT: For proper operation of the water

softener, do not connect the water softener

valve drain tubing to the salt storage tank

overflow hose.

RINSE OUT CARBON FINES

Small particles of carbon filtration material are

generated during manufacturing and shipping.

These particles will exit the media tank with

the first water that flows through the softener.

These carbon “fines” are not harmful, but give

the water a gray color and should be rinsed

down the drain before any water from the

softener is directed to the home’s faucets or

water heater.

TEST FOR LEAKS

To prevent air pressure in the water softener

and plumbing system, complete the following

steps in order:

1. Fully open two or more softened cold water

faucets close to the water softener, located

down stream from the water softener.

2.

Place the bypass valve (single or 3 valve)

into the”bypass” position (see Figures 4 or 5).

3. Slowly open the main water supply valve.

Run water until there is a steady flow from

the opened faucets, with no air bubbles.

4. Place bypass valve(s) in “service” or soft

water position as follows:

• Single bypass valve (Figure 4): Slowly

move the valve stem toward “service,”

pausing several times to allow the water

softener to fill with water.

•

3 valve bypass (Figure 5): Fully close the

bypass valve and open the outlet valve. Slowly

open the inlet valve, pausing several times to

allow the water softener to fill with water.

5. After about three minutes, open a hot water

faucet until there is a steady flow and there

are no air bubbles, then close this faucet.

6.

Close all cold water faucets and check for leaks

at the plumbing connections that you made.

7. Check for leaks around clips at softener’s

inlet and outlet. If a leak occurs at a clip,

depressurize the plumbing (turn off the water

supply and open faucets) before removing

clip. When removing clips at the softener’s

inlet or outlet, push the single bypass valve

body toward the softener (See Figure 13).

Improper removal may damage clips. Do not

reinstall damaged clips.

Figure 13

....depressurize the

plumbing, then push

Bypass Valve body

toward softener

If removing

clips.....

Installation Instructions

15

ADD WATER AND SALT TO THE SALT

STORAGE TANK

WARNING

EXCESSIVE WEIGHT HAZARD:

Use two or more people to move and lift salt

bags. Failure to do so can result in back or

other injuries.

1. Using a container, add about three gallons of

clean water into the salt storage tank.

2. Add salt to the storage tank. Use nugget,

pellet or coarse solar salts with less than 1%

impurities.

PLUG IN THE WATER SOFTENER

1. Plug the water softener into an electrical

outlet that is not controlled by a switch.

2. Replace the top cover.

3. Replace the salt hole cover.

NOTE: The water heater is filled with hard

water and,as hot water is used, it will refill

with conditioned water. In a few days, the hot

water will be fully conditioned. To have fully

conditioned hot water immediately, wait until

the initial recharge is over. Then, drain the

water heater(following instructions for water

heater) until water runs cold.

WARNING

Discard all unused

parts and packaging material after

installation. Small parts remaining after the

installation could be a choke hazard.

SANITIZE THE WATER SOFTENER /

SANITIZE AFTER SERVICE

1. Open salt hole cover, remove the brinewell

cover and pour about 3 oz. (6 tablespoons)

of household bleach into the softener

brinewell. Replace the brinewell cover.

2. Make sure the bypass valve(s) is in the

“service”(open) position.

3. Start a recharge (regeneration) as follows:

Press the RECHARGE button and hold for

three seconds, until “RECHARGE NOW”

begins to flash in the display, starting a

recharge. This recharge draws the sanitizing

bleach or brine into and through the water

softener. Any air remaining in the water

softener is purged to the drain. During this

time periodically check for leaks.

NOTE: As with all other water system

applications, leaks may occur. Leaks may not

be immediately apparent. Recheck 24 hours

after first recharge cycle is complete.

4. After the recharge has completed, fully open

a cold water faucet, downstream from the

softener, and allow 50 gallons of water to

pass through the system. This should take at

least 20 minutes. Close the faucet.

Installation Instructions

16

Programming the Water Softener

When the transformer is plugged into the

electrical outlet, a model code and test number

(example: J3.4 & H31) are shown in the

display. Then, “12:00 PM” begins to flash. An

arrow is displayed next to CLOCK on the

face plate decal.

CONTROL OPERATION:

• CONTROL SETTINGS REQUIRED upon

initial installation and after an extended power

outage.

• Use the MODE/SET button to scroll arrow to

desired control function set.

• After the mode is selected use the UP

and DOWN buttons to change the

settings of the control.

• Press the MODE/SET button to accept

changes.

• A “beep” sounds while pressing buttons for

control programming. One beep signals a

change in the control display. Repeated

beeps mean the control will not accept a

change from the button you have pressed,

and you should select another button.

SET TIME OF DAY

1. Press MODE/SET button until the arrow

points to CLOCK.

2. Press the UP or DOWN buttons

to set the present time. UP moves the

display ahead; DOWN sets the time

back. Be sure AM and PM is correct.

NOTE: Press buttons and quickly release

to slowly advance the display one number

at a time. Hold the buttons down for fast

advance.

3. When the correct time is shown in the

display, press MODE/SET to accept.

Salt Level

Clock

Hardness

Recharge

PM

17

Programming the Water Softener

SET WATER HARDNESS NUMBER

1. Press the MODE/SET button until the arrow

points to HARDNESS. A flashing 25 will

appear in the display.

2. Press the UP or DOWN buttons to

set your water hardness number.

NOTE: If your water supply contains iron,

compensate for it by adding to the water

hardness number. For example, assume

your water is 20 gpg hard and contains 2

ppm iron. Add 5 to the hardness number

for each 1 ppm or iron. In this example, you

would use 30 for your hardness number.

3. When the display shows your water

hardness (in grains per gallon), press

MODE/SET to accept.

You can get the grains per gallon (gpg)

hardness of your water supply from a

water analysis laboratory. If you are on

a municipal supply, call your local water

department. Or call Legend Technical

Services, an independent laboratory,

to request a water hardness test kit at

1.800.949.8220, Option 4. If your report

shows hardness in parts per million (ppm)

or milligrams per liter (mg/l), simply divide

by 17.1 to get the equivalent number of

grains per gallon.

SET RECHARGE (STARTING) TIME

1. Press the MODE/SET button until the arrow

points to RECHARGE.

NOTE: A flashing 2:00 AM (factory default)

should show in the display. This is a good

time for recharge to start (takes about 2

hours) in most households because water

is not in use. HARD WATER is bypassed to

house faucets during recharge.

If no change is needed, go to step 3. To

Change the recharge starting time, follow

step 2.

2. Press UP or DOWN button to set

the desired recharge start time. Be sure

to observe the AM or PM as you did when

setting the time of day.

3. Press the MODE/SET button to accept.

20 gpg hardness

2 ppm iron x 5 = 10 +10

(times) 30 HARDNESS NUMBER

Salt Level

Clock

Hardness

Recharge

Salt Level

Clock

Hardness

Recharge

AM

18

SET SALT LEVEL

1. Press the MODE/SET button until the arrow

points to SALT LEVEL.

2. Determine level of salt in brine tank using the

numbered scale on side of brine well, inside

brine tank (see Figure 14).

3. Press UP or DOWN button to set

the SALT LEVEL to correspond to level on

the numbered scale in brine tank.

NOTE: Each press of a button changes the

level by increments of 0.5 up to 8.0.

Lowering the salt level below zero turns the

SALT LEVEL indicator OFF.

4. Press the MODE/SET button to accept. The

display shows the present time of day and

DAYS TO EMPTY.

DAYS TO EMPTY

The words DAYS TO EMPTY and a number

are shown in the lower half of the display. This

information is shown in the normal run display.

This is to inform the user of the number of

days before the salt level in the brine tank

reaches Level 0. There will be salt left in the

salt tank, but it may not be sufficient to fully

recharge the system. Salt should be added

at this time to avoid hard water. The value is

updated daily and whenever the SALT LEVEL

value is changed.

NOTE: For the first several weeks of operation,

the DAYS TO EMPTY may provide erratic

operation. For example, the blue indicator light

may flash, showing that more salt is required

when the actual salt level in the tank is well

above the Level 0. In some cases, the DAYS

TO EMPTY may even increase over a several

week period.

It takes a couple of months for the water

softener to learn your water usage pattern.

Once it does this, it will accurately determine

actual salt usage pattern. During this first

period, check salt level when blue indicator

light flashes. If the salt level in the tank is at

Level 1 or above, allow system to run. Be sure

to reset your salt level indicator each time you

add salt to the system.

START A RECHARGE

Press the RECHARGE button and hold for

three seconds, until “RECHARGE NOW”

begins to flash in the display, starting a

recharge. This recharge draws the sanitizing

bleach or brine into and through the water

softener. Any air remaining in the water

softener is purged to the drain. During this time

periodically check for leaks.

NOTE: As with all other water system

applications, leaks may occur. Leaks may not

be immediately apparent. Recheck 24 hours

after first recharge cycle is complete.

Salt Level

Clock

Hardness

Recharge

Salt Level

Clock

Hardness

Recharge

PM

Days to Empty

AM

Days to Empty

8

7

6

5

4

3

2

1

Figure 14

Programming the Water Softener

19

OPTIONAL CONTROL SETTINGS

The controller display has several options and

features.

LOW SALT ALARM

The LOW SALT ALARM,

when enabled, will sound

the beeper when the DAYS

TO EMPTY value is 15

days or less. To change

this setting, press and hold

the MODE/SET button for

3 seconds or hear a beep.

ON (factory default) or OFF

will flash in the display.

Press the UP or DOWN

buttons to toggle this

feature ON or OFF. Press

the MODE/SET button to

accept, and the display will

move to the PRERINSE ON/

OFF screen. Press the UP or DOWN

buttons to turn prerinse on or off.

PRERINSE

If your water contains

sediment the prerinse

feature will remove

sediment from the resin

bed prior to regeneration.

Press the MODE/SET

button and the display will

move to Prerinse Time

mode. In this screen you

can adjust the duration of

the prerinse by pressing

the UP or DOWN

buttons. Press the MODE/

SET button to accept, and the display will

move to the Back Wash screen.

BACKWASH AND FAST RINSE

If you experience salty tasting water after

regeneration, you may need to increase the

backwash and fast rinse times. The cycle times

during regenerations are determined by the

softener’s electronic controller. However, you

may increase the backwash and fast rinse

times. You may add up to 10 minutes.

For Backwash, you can

add up to 10 minutes in

1 minute increments, by

pressing the UP button,

or subtract time by pressing

the DOWN button.

For Fast Rinse, press

MODE/SET and the display

moves to the add fast rinse

time screen. You can add

up to 10 minutes in 1 minute

increments, by pressing the

UP button, or subtract time by pressing

the DOWN button. Press the MODE/SET

button to accept, and the display will move to

the Run Display screen.

SALT SAVER

When this feature is ON, the water softener

will operate at salt efficiencies of 4000 grains

of hardness per pound of salt or higher (May

recharge more often using smaller salt dosage

and less water). The softener is shipped with

this feature set OFF.

In the state of California: You must turn the

Salt Saver Feature ON. This may initiate more

frequent recharges. However, it will operate at

4,000 grains per pound of salt.

To turn Salt Saver ON: Press

the Salt Saver button once until

the blue status light above the

button is ON.

Programming the Water Softener

20

FEATURE: OTHER DATA DISPLAY

These models have an option to have the

run display indicate different information. The

information displayed on the top half of the

display can be changed to one of the following

by pressing UP or DOWN buttons

:

• CAPACITY REMAINING

– This is the percentage

of water softening capacity

remaining. Immediately

after a regeneration, 100%

shows. As water is used,

the percentage will decrease until the next

regeneration. During regenerations, the

percentage increments upward.

When present time is displayed, press the

DOWN button; % Remaining will appear in

the display. The value shown is between 0 and

100 percent. This value is based on current

operating capacity. Pressing the UP button

will return the screen to the previous display.

• AVERAGE DAILY

GALLONS – The figure

displayed is the average

gallons of water used by the

household each day over

the past seven-day period.

Press the DOWN button again to display

the Average Daily Gallons. Average Daily

Gallons will appear in the display. This value

is updated every night at midnight. Pressing

the UP button will return the screen to the

previous display.

• FLOW RATE, GPM

– When using soft water,

this display shows the flow

rate passing through the

softener (in gallons per

minute). Zero shows if water

is not passing through the softener.

Press the DOWN button again to display

the flow rate. Gallons/Min will appear in the

display. This value is updated every 1»2 second.

Pressing the UP button will return the

screen to the previous display. Pressing the

DOWN button will return the screen to the

present time display.

RESETTING TO FACTORY DEFAULT

To reset the electronic controller to its factory

default for all settings (time, hardness, etc.):

1. Press the MODE/SET button and hold

until the display changes twice to show the

flashing mode code.

2. Press the UP button to display a flashing

“SoS”.

3. Press the MODE/SET button and the

electronic controller will restart.

4. Set the present time, hardness, etc, as

described in the Programming the Water

Softener section

Days to Empty

Recharge

Tonight

% Remaining

Days to Empty

Recharge

Tonight

Average Daily

Gallons

Days to Empty

Gallons/Min

Programming the Water Softener

La page est en cours de chargement...

GE GXSH40V Le manuel du propriétaire

GE GXSH40V Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents