Kichler Lighting 43255DAW Manuel utilisateur

Marque
Kichler Lighting
Modèle
43255DAW
Taper
Manuel utilisateur
IMPORTANT: The fixture must be supported while mounting
fixture to ceiling.
1) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
2) Pass fixture wire through hole in bottom of loop. Thread
loop onto threaded pipe on top of fixture body.
3) Align hole in bottom of arm with hole in bottom trim piece.
4) Thread ball stud through hole in arm and into bottom trim
piece. Tighten ball stud to secure arm in place.
4) Repeat steps 3 and 4 for remaining arms.
5) Align hole in top of arm with hole in top trim on center stem.
6) Thread ball stud through hole in arm and into top trim.
Tighten ball stud to secure arm in place.
7) Repeat steps 5 and 6 for remaining arms.
8) Pass fixture wire through hole in bottom of loop. Thread loop
onto threaded pipe on top of top trim.
9) Thread hexnut onto threaded pipe so that 5 threads are
exposed above hexnut. From underside of mounting strap,
thread long end of threaded pipe into hole in mounting strap
until hexnut touches mounting strap. Tighten hexnut against
mounting strap.
10) Thread second hexnut onto other end of threaded pipe.
Tighten hexnut up against mounting strap. Thread third
hexnut onto same end of threaded pipe until almost touching
second hexnut.
11) Connect mounting strap to outlet box.
12) Weave electrical wire and ground wire through chain links no
more than 3 inches apart. Pass wires through threaded ring,
screw collar loop, canopy and threaded pipe and into
outlet box
13) Connect fixture ground wire to outlet box ground wire with
wire connector. (Not provided.) Never connect ground wire
to black or white power supply wire.
14) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
15) Raise canopy to ceiling. Pass hole in canopy over end of
threaded pipe.
16) Thread screw collar loop onto threaded pipe protruding from
canopy. Screw threaded ring onto screw collar loop. Tighten
threaded ring up against canopy.
Date Issued: 9/18/15 IS-43255-CB
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
K I C H L E R
MOUNTING STRAP
PATTE DE FIXATION
HEXNUT
ECROU HEXAGONAL
THREADED PIPE
TUBE FILETÉ
SCREW COLLAR LOOP
COLLIER-ÉCROU
CANOPY
CACHE
THREADED RING
BAGUE FILETÉE
LOOP
ANNEAU
TOP TRIM
GARNITURE
SUPÉRIEUR
BOTTOM TRIM
GUARNICIÓN INFERIOR
THREADED PIPE
TUBE FILETÉ
ARM
BRAS
BALL STUD
GOUJON À BILLE
BALL STUD
GOUJON À
BILLE
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
  • Page 1 1

Kichler Lighting 43255DAW Manuel utilisateur

Marque
Kichler Lighting
Modèle
43255DAW
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes