Summit GC5272B2 Le manuel du propriétaire

INSTRUCTIONS AND

RECOMMENDATIONS FOR THE USE,

INSTALLATION AND MAINTENANCE OF

BUILT-IN GAS COOKTOPS

Dear customer,

Thank you for buying one of our products.

We are sure that this new, modern, functional and practical appliance, made using the finest quality

materials, will fully satisfy your requirements. This new appliance is very easy to use, but in order to

obtain the best results, we strongly recommend that you read this booklet carefully before use.

These instructions are valid exclusively for countries indicated on the label of the appliance.

The manufacturer cannot be considered responsible for any damages to people or to things in the

event of incorrect installation or improper use of the appliance.

Felix Storch, Inc.

Summit Appliance Division

An ISO 9001:2015 registered company

770 Garrison Avenue

Bronx, New York 10474

www.summitappliance.com

MODEL: GC22SS - GC527SS - GC5271W - GC5272B

The Manufacturer cannot be held responsible for any imprecision due to printing or copying errors

contained in this booklet. The figures shown are purely indicative. We reserve the right to make any

changes to our products which we consider to be necessary or useful, also in the interest of the user,

without affecting their essential characteristics in terms of functionality and safety.

This cooktop was designed to be used exclusively as a cooking appliance: any other use (such as

heating rooms) is to be considered improper and dangerous.

COD. 04037GT - 11..05.2017

2

TABLE OF CONTENTS

Important Safeguards .......................................................................... 3

Location of Parts ................................................................................. 4

Installation..................................................................................... 5 - 8

Installing the Cooktop. ................................................................ 5

Sealing the Cooktop. .................................................................. 6

Room Ventilation. ........................................................................ 6

Gas Connection. ......................................................................... 7

Electrical Connection. ................................................................. 8

Adjustments ......................................................................................... 9

Conversions .................................................................................. 10-11

Using the Cooktop .............................................................................. 12

Lighting the Burners................................................................... 12

Proper Use of the Burners. .................................................. 12-13

Cleaning .............................................................................................. .14

Servicing. ............................................................................................ .15

Replacing Components

Limited Warranty................................................................................ .16

3

IMPORTANT SAFEGUARDS

1) SAFETY INSTRUCTIONS

For all appliances:

●

The product shall be installed according to the statement that the installation must conform with local

codes

or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54.

●

The product must be electrically grounded in accordance with local codes or, in the absence of local

codes, with the National Electrical Code, ANSI/NFPA 70.

●

Make sure the gas connection complies with local codes and regulations. In the absence of local codes,

installations must comply with the American National Standard, National Fuel Gas Code ANSI Z223 / NFPA

54 or Canadian CAN / CGA_B 149.1 or CAN / CGA-149.2.

●

The appliance and its individual shutoff valve must be disconnected from the gas supply piping system

during any pressure testing of that system at test pressures in excess of ½ psi (3.5 kPa). The maximum

gas supply pressure is 4 inch WC and 11 inch WC and the gas pressure regulator provided is regulated

to 1 inch water column above the manufacturer’s specified manifold pressure.

●

Always disconnect all cord-connected appliances before servicing. Appliances shall include

instructions relative to location of the wall

receptacle and a warning to the user to disconnect the

electrical supply before servicing the

appliance.

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing

property damage, personal injury or death.

●

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

2) WHAT TO DO IF YOU SMELL GAS

-

Do not try to light any appliance.

-

Do not touch any electrical switch; do not use any phone in your building.

-

Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions.

-

If you cannot reach your gas supplier, call the fire department.

●

Installation and service must be performed by a qualified installer, service agency or

the gas supplier.

●

Save any nozzles removed from the appliance for future use.

●

The maximum depth of cabinets installed above the cooktop should be 13 inches (330 mm).

●

Keep the appliance clear and free from combustible materials, gasoline and other flammable vapors

and liquids.

●

Do not obstruct the flow of gas or block any air vents.

●

Shut off gas to the unit by manually closing the independent gas valve before performing any pressure

testing of the gas supply system with test pressures equal to or lower than 1/2 psi (3.5 kPa).

4

LOCATION OF PARTS

MODEL : GC22SS

MODELS :

GC527SS

GC5271W

GC5272B

art No.

Description

Heat supplied

1

Ultra rapid burner 11 000 Btu/h

2 Fast burner 10 000 Btu/h

3 Auxiliary burner 3 550 Btu/h

4 Semirapid burner 6 100 Btu/h

6-7

Grate

8

Burner no. 1 control knob

9 Burner no. 3 control knob

10

Burner no. 2 control knob

11

Burner no. 4 control knob

NOTICE: This appliance has been manufactured for residential use only.

Warning: During operation the work surfaces

of the cooking area become very hot:

Keep

children away!

5

INSTALLATION

Installation, adjustment of controls and maintenance must only be carried out by qualified

personnel.

Incorrect installation may cause damage to persons, animals or property for which the

Manufacturer will not be considered responsible. During the life of the system, the automatic

safety or regulating devices on the appliance may only be modified by the manufacturer or by his

duly authorized dealer.

Installing the Cooktop

Check that the appliance is in good condition after having removed the outer packaging and internal

wrappings from around the various loose parts. In case of doubt, do not use the appliance and contact

qualified personnel.

Never leave packaging materials (cardboard, bags, Styrofoam, nails, etc.) within the reach of

children since these items could become sources of danger.

The measurements of the opening made in the top of the modular cabinet and into which the cooktop will

be installed are indicated in Fig. 1 and the following chart. Always comply with the measurements given

for the hole into which the appliance will be recessed (see Figs. 1 and 2).

30”

Min. 6”

FIG. 1

FIG. 2

Use

These

Dimensions

(in

inches)

Model No.

A

B

C

D

E

GC22SS

11-

¼

19

2-

½

2-

½

2-

7/8

GC527SS – GC5271W

GC5272B

21-49/64

18-5/8

2-

½

2-

½

6 - 57/64

Use These Dimensions (mm)

Model No.

A

B

C

D

E

GC22SS

282

482

59

100

GC527SS – GC5271W

GC5272B

553

473

63,5

175

6

Sealing the Cooktop

The cooktop has a special seal which prevents liquid from infiltrating into the cabinet. Strictly comply with the

following instructions in order to apply this seal correctly:

-

Take off all the movable parts of the cooktop.

-

Detach the seals from their backing, checking that the transparent protection still adheres to the seal itself.

-

Overturn the cooktop and correctly position seal “E” (fig. 3) under the edge of the cooktop itself, so that the

outer side of the seal perfectly matches the outer edge of the cooktop. The ends of the strips

must fit

together without overlapping.

-

Evenly and securely fix the seal to the cooktop, pressing into place with the fingers and remove the strip of

protective transparent film from the seal and set the plate into the hole made in the cabinet.

-

Fix the cooktop with the proper brackets “S” and fit the prominent part into the porthole “H” on the bottom; turn

the

screw “F” until the bracket “S” touches the top (fig. 4). In fastening the brackets, do not use a mechanical

or

electric screwdriver. Instead, use a hand-operated screwdriver and exert only moderate force.

The adjacent walls (left, right or behind) that exceed the cooktop in height must be at a minimum distance from

the cut hole as indicated in Fig. 1 and the chart on the preceding page.

In order to avoid accidentally touching the hot cooktop bottom, it is necessary to put a horizontal wooden insert, attached

by screws, at a minimum distance of

6"

below the lower surface of the cooktop (see Fig. 1).

Room Ventilation

To ensure proper operation of the appliance, be sure that the room where it is installed has adequate

ventilation.

The appliance should not be installed with a ventilation system that blows air downward

toward the appliance. It may cause ignition and combustion problems with the gas cooking

appliance resulting in personal injury or unintended operation.

FIG. 3

FIG. 4

7

Gas Connection

Natural Gas and Propane Gas

Natural gas installations require the connection of a gas regulator to the cooktop. You will find this

regulator among the accessories supplied with the appliance.

Assemble the regulator (noting the direction of gas flow) and transition pieces (supplied) in accordance

with the figure below.

The transition piece on the supply side of the regulator must be provided by the installer. Unions

compatible with the hose fittings must be used and connections tested for gas leaks.

Be sure that the supply connection point is accessible with the appliance installed.

WARNING:

Be sure the hose assembly is restrained from accidental contact with the flue or flue outlet of an under-

counter oven.

Electrical Connection

The electrical connections of the appliance must be carried out in compliance with local standards and

provisions.

Before connecting the appliance, check that:

1.

The electrical capacity of the main electrical supply and current sockets suit the maximum power

rating of the appliance. (See the data label attached to the bottom of the cooktop.)

2.

The socket or system has an efficient ground connection in compliance with local standards and

provisions. The manufacturer is not responsible for failure to comply with these provisions.

8

Electrical Connection

The electrical connections of the appliance must be carried out in compliance with

local standards and provisions.

Before connecting the appliance, check that:

1.

The electrical capacity of the main electrical supply and current sockets suit the

maximum power rating of the appliance. (See the data label attached to the bottom

of the cooktop.)

2.

The socket or system has an efficient ground connection in compliance with local

standards and provisions. The manufacturer is not responsible for failure to comply

with these provisions.

When the appliance is connected to electrical power by a socket:

• Fit a standard plug suited to the load indicated on the data label to the cable.

• Fit the wires following Fig. 5, noting the following correspondences:

Letter L (live) = wire

Letter N (neutral) = wire

Ground symbol = green or yellow-green wire

• Never use adapters or shunts for connection since these could create false

contacts and lead to dangerous overheating.

•The outlet must be accessible after the cooktop is built in.

FIG. 5

When the appliance is connected directly to the electrical main:

• Install an omnipolar circuit-breaker between the appliance and the electrical main.

This circuit-breaker should be sized in compliance with local installation

regulations.

• Remember that the ground wire must not be interrupted by the circuit-breaker.

• For optimum safety, the electrical connection may also be protected by a high-

sensitivity differential circuit-breaker.

You are strongly advised to fix the yellow-green ground wire to an efficient

grounding system.

9

ADJUSTMENTS

Always disconnect the appliance from the electrical power source before making any

adjustments. All seals must be replaced by the technician when any adjustments are completed.

Taps

"Reduced rate" adjustment:

1.

Switch on the burner and turn the relative knob to the “Reduced rate” position (small flame fig. 8 page

10).

2.

Remove knob “M” (fig. 6 and 6/A) of the tap, which is simply pressed on to its rod.

3.

The by-pass for minimal rate regulation can be: beside the tap (fig. 6) or inside the shaft. In any case,

to access to regulation, it can be done trough the insertion of a small screwdriver ‘’D’’ beside the tap (fig.

6) or in the hole ‘’C’’ inside the shaft of the tap (fig 6/A).

Turn the throttle screw to the right or left until the burner flame has been adequately regulated to the

“Reduced rate” position.

The flame should not be too low: the lowest small flame should be continuous and steady. Re-assemble

the several components.

It is understood that only burners operating with Natural Gas or City Gas should be subjected to

the above-mentioned adjustments. The screw must be fully locked when the burners operate with

Propane (turn clockwise).

The operations described above can be carried out easily, whatever the position of the cooktop or

however it is fastened to the work surface.

THE BURNERS DO NOT REQUIRE ANY REGULATION OF INCOMING AIR

.

FIG. 6 FIG. 6/A

10

CONVERSIONS

Replacing Nozzles

The burners can be adapted to suit different types of gas by fitting the nozzles that correspond to the gas

used. To do this, it is necessary to remove the burner heads and use a straight key "B" to unscrew the

nozzle "A" (see Fig. 7) and replace it with a nozzle corresponding to the gas used.

Be sure the nozzle is seated tightly.

After making these replacements, the technician must regulate the burners as described in

Adjustments on the previous page and apply the label corresponding to the new gas type in place

of that previously applied. This label is contained in the spare nozzle bag.

How to change the setting of the pressure regulator supplied with the cooktop:

The gas regulator was set up to Natural Gas. To convert to LP Gas:

1.

Unscrew the aluminum cap

2.

Remove and turn the plastic pin 180°

3.

Screw in the plastic pin

4.

Screw in the aluminum cap

To make it easier for the fitter, we have prepared a table indicating the flow capacities, the heat

capacities of the

burners, the diameter of the nozzles and the working pressure for the various types of

gas.

FIG. 7

11

BURNERS

GAS

NORMAL

PRESSURE

inches water

column

INJECTOR

DIAMETER

1/100 mm

NOMINAL HEAT

INPUT (Btu/h)

N°

DESCRIPTION

Min.

Max.

1

ULTRA RAPID

PROPANE HD - 5

NATURAL GAS

11

4

94

176

4 400

11 000

2

FAST

PROPANE HD - 5

NATURAL GAS

11

4

91

155

2 500

10 000

3

AUXILIARY

PROPANE HD - 5

NATURAL GAS

11

4

53

90

1 200

3 550

4

SEMIRAPID

PROPANE HD - 5

NATURAL GAS

11

4

70

120

1 500

6 100

3

12

USING THE COOKTOP

Lighting the burners

A diagram is screened beside each knob on the control panel of your cooktop. This diagram indicates to

which burner the knob in question corresponds. After having opened the gas main or bottled gas tap,

light the burners as described below:

The knobs of the burners are equipped with a safety cut-off device. They must be turned in a counter-

clockwise direction until they reach the full-on position (large flame icon, Fig. 8) and come to a stop. Now

push down on the knob. The burner should ignite in 2 or 3 seconds. Keep the knob depressed as you

turn

it toward the reduced rate position (small flame icon, Fig. 8) to adjust the flame. Should the flame

accidentally go out, turn the burner control knob off and wait at least 1 minute before attempting to light

it

again.

FIG. 8

FIG. 9

Proper use of the burners

To achieve maximum efficiency with the least possible gas consumption, keep the following instructions

in mind:

•

Use the correct pan size for each burner. (See the following table and Fig. 9.)

•

When the pan comes to a boil, set the knob to a reduced rate position (small flame icon, Fig. 8).

•

Always put lids on the pans.

•

Use only flat-bottomed pans.

13

Burners

Power Ratings

Pan Diameter

In cm

ULTRA RAPID

11 0000

9" to 10

½"

24 - 26

FAST

10 000

8" to 9 ½"

20 - 22

SEMIRAPID

6 100

6"

to

7

½"

16 - 18

AUXILIARY

3 550

4" to 5 ½"

10 – 14

WARNINGS:

•

Burners will only ignite when the corresponding knob has been set to the Full-on position (large flame icon,

Fig. 8).

•

Matches can be used to ignite the burners during a power outage, but use caution.

•

Never leave the appliance unattended when the burners are being used. Make sure there are no children in

the vicinity. In particular, make sure that the pan handles are correctly positioned. Keep checking on foods

that require oil or other grease to cook since these products can easily catch fire.

•

The appliance must not be used by people (including children) with impaired mental or physical capacities,

or without experience of using electrical devices, unless supervised or instructed by an adult responsible for

their safety and care. Children should not be allowed to play with the equipment.

•

Never use aerosol sprays near the appliance when it is operating.

•

Containers wider than the unit are not recommended.

NOTES:

•

The use of a gas cooking appliance produces heat and moisture in the room in which it is installed. The

room must therefore be well ventilated.

•

Intensive and lengthy use of the appliance may require additional ventilation. This can be achieved by

opening a window or by increasing the power of the mechanical exhaust system if installed.

WARNING!

NEVER use this appliance as a space heater

to heat or warm the room. Doing so may result

in carbon monoxide poisoning and

overheating of the appliance.

14

CLEANING

IMPORTANT:

Always disconnect the appliance from the gas

and electricity supplies before carrying out

any cleaning operation.

Periodically wash the hot plate, the enameled steel

pan support, the enameled burner caps “A”, “B”

and “C” and the burner heads "T" (see fig. 10 and

11) with lukewarm soapy water. Also

clean plugs

"AC" and flame detection "TC"

(see fig. 10). Clean

them gently with a small nylon

brush as shown (see

fig. 12) and allow to dry fully.

Do not wash in the

dishwasher. It is very important

to clean the surface

soon after every use, while the

glass is still

somewhat warm.

Do not allow vinegar, coffee, milk, salt water,

or

lemon or tomato juice to remain in contact

with

the enameled surfaces for long periods of

time.

Do not clean using abrasive metal scourers,

abrasive powders or corrosive sprays.

WARNINGS:

Comply with the following instructions, before

remounting the parts:

- Check that burner head slots have not

become clogged by foreign bodies.

- Check that enameled burner caps “A-B-C”

(fig. 10-11) have b e e n correctly positioned

on the burner head. They must be steady.

- The exact position of the pan support is

established by the rounded corners, which

should be set towards the side edge of the

hot plate.

- Do not force the taps if they are difficult to

open or close. Contact customer service for

technical assistance or repairs.

- Correctly preserve the plate after use by

treating it with special, easily available

products. This will keep the surface of the

plate clean and bright. The operation will

also prevent the formation of rust.

- Don’t use steam jets to clean the

equipment.

- Food b u r n t onto an electric plate must

be removed dry.

- After use, pour a little lukewarm oil on the

plate and wipe it with a cloth.

Note: Continuous use can cause the

burners to change color due to the

high

temperature.

FIG. 10

FIG. 11

FIG. 12

15

SERVICING

Always disconnect the appliance from the electric and gas supplies before proceeding with

any servicing operation.

Replacing Components

To replace the components housed inside the appliance, remove the trivets and the burners from the upper

part of the cooktop. Remove the fixing screws "V" of the burner (Fig. 13) and the knobs using hand pressure

to remove them from the appliance.

After having carried out these operations, the burners (Fig. 14), taps (Fig. 15) and electrical components can

all be replaced (Fig. 16).

It is advisable to change seal "D" (Fig. 15) whenever a tap is replaced to ensure a perfect tightness.

Greasing the taps (See Fig. 17-18)

If a tap becomes stiff to operate, it must be immediately greased in compliance with the following

instructions:

1.

Remove the tap.

2.

Clean the cone and its housing using a cloth soaked in solvent.

3 .Lightly grease the cone.

4 .Fit the cone back into place, operate it a few times and then remove it again. Eliminate any excess

grease and check that the gas ducts have not become clogged.

5.

Fit all parts back into place, following the disassembly order in reverse.

6.

The tight closure test must be done using a foaming liquid.

Never use a flame for this test.

WARNING:

MAINTENANCE MUST ONLY BE PERFORMED

BY AUTHORIZED PERSONS.

FIG. 13

FIG. 14

FIG. 15

FIG. 16

FIG. 17

FIG. 18

LIMITED WARRANTY

Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is

operated and maintained according to instructions attached to or furnished with the product, warrantor

will

pay for factory-specified parts and repair labor to correct defects in materials or workmanship.

Service

must be provided by a designated service company. Outside the 48 states, all parts are

warranted for one

year from manufacturing defects. Plastic parts, shelves and cabinets are warranted to

be manufactured to

commercially acceptable standards, and are not covered from damage during

handling or breakage.

ITEMS WARRANTOR WILL NOT PAY FOR:

•

Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to

replace or repair fuses or to correct wiring or plumbing.

•

Service calls to repair or replace appliance light bulbs or broken glass shelves. Consumable parts (such

as filters) are excluded from warranty coverage.

•

Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation,

installation not in accordance with electrical or plumbing codes, or use of products not approved by

warrantor.

•

Replacement parts or repair labor costs for units operated outside the United States.

•

Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

•

The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not

installed in accordance with published installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE

PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR.

WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME

STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY

OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO

YOU. THIS WARRANTY

GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER

RIGHTS, WHICH VARY

FROM STATE TO STATE.

WARNING!

This product can expose you to chemicals including Nickel (Metallic) which is

known to the State of California to cause cancer.

For more information go to www.P65Warnings.ca.gov

Note: Nickel is a component in all stainless steel and some other metal components

Call customer service toll free in the U.S.A. @ 1-800-932-4267, Monday to Friday 9:00 am. - 5:00 p.m. (ET).

Order parts online at www.summitappliance.com/support

Felix Storch, Inc.

Summit Appliance Division

770 Garrison Avenue

Bronx, NY 10474

Phone: (718) 893-3900

Fax: (844) 478-8799

Web Site:

www.summitappliance.com

INSTRUCTIONS ET RECOMMENDATIONS

POUR L’UTILISATION, L’INSTALLATION ET

L’ENTRETIEN DE LA TABLE DE CUISSON

AU GAZ ENCASTRABLE

Cher client, nous vous remercions d’avoir choisi nos produits.

Nous vous assurons que ce nouvel appareil moderne, fonctionnel et pratique à la fois, fabriqué

avec des matériaux de première qualité, sera satisfaire pleinement vos exigences. Ce nouvel

appareil est très facile d’utilisation, mais afin d’obtenir les meilleurs résultats, nous vous

recommandons tout particulièrement, de lire attentivement cette notice avant toute utilisation.

Ces instructions sont valables uniquement pour les pays dont les symboles

d’identification figurent sur l'étiquette de l’appareil.

Le fabriquant ne peut être tenu pour responsable en cas de dommages corporels ou matériels en

raison d’une installation incorrecte ou un usage abusif de l’appareil.

Felix Storch, Inc.

Summit Appliance Division

Une compagnie enregistrée d'ISO 9001: 2015

770 Garrison Avenue

Bronx, New York 10474

www.summitappliance.com

MODÈLE : GC22SS - GC527SS-GC5271W-GC5272B

Le fabriquant ne peut être tenu pour responsable des imprécisions dues à l’impression ou des erreurs de

reproduction dans la présente notice. Les images présentées ont un caractère purement indicatif. Nous

nous réservons le droit d’apporter des modifications à nos produits, que nous jugeons nécessaires ou

utiles, notamment dans l’intérêt de l’utilisateur, tout en conservant ses caractéristiques essentielles en

termes de fonctionnement et sécurité.

Cette table de cuisson a été conçue pour être utilisée exclusivement comme appareil de cuisson :

toute autre utilisation (telle que dispositif de chauffage de la pièce) est considérée comme étant

abusive et dangereuse.

COD. 04037GT (FR)

18

TABLE DES MATIÈRES

Précautions importantes .................................................................. 19

Position des composants ................................................................ 20

Installation .................................................................................................... 21 - 24

Installation de la table de cuisson. ........................................................... 21

Fixation de la table de cuisson. ................................................................ 22

Ventilation de la pièce. ............................................................................... 22

Raccordement au gaz. ............................................................................... 23

Branchement électrique.......................................................23 - 24

Réglages ............................................................................................ 25

Conversions ................................................................................................. 26 - 27

Utilisation de la table de cuisson ............................................ 28 - 29

Allumage des brûleurs ............................................................................. 28

Utilisation correcte des brûleurs ....................................................... 28 - 29

Nettoyage ........................................................................................... 30

Entretien ............................................................................................. 31

Remplacement des composants

Garantie limitée ................................................................................. 32

19

PRÉCAUTIONS IMPORTANTES

1) CONSIGNES DE SÉCURITÉ

Pour tous les appareils :

● Le produit doit être installé conformément à la déclaration que l'installation doit être conforme aux

codes locaux ou, en l'absence de codes locaux, avec le National Fuel Gas Code, ANSI Z223.1 / NFPA

54.

● Le produit doit être mis à la terre conformément aux codes locaux ou, en l'absence de codes locaux,

avec le National Electrical Code, ANSI / NFPA 70.

●

Assurez-vous que la connexion de gaz est conforme aux codes et règlements locaux. En l'absence de

codes locaux, les installations doivent être conformes à la norme nationale américaine, National Fuel

Gas Code ANSI Z223 / NFPA 54 ou canadien CAN / CGA_B 149.1 ou CAN / CGA-149.2.

●

Cet appareil et son robinet d’arrêt doivent être coupés de l’arrivée de gaz lors des essais de pression

effectués à une valeur supérieure à ½ psi (3.5 kPa). La pression maximale d’alimentation en gaz est de

4 pouces d’eau et 11 pouces d’eau et le régulateur de pression du gaz est réglé à 1 pouce d’eau au-

dessus de la pression d’admission spécifiée par le fabriquant.

●

Toujours débrancher le câble d’alimentation ; les appareils sont fournis avec les instructions relatives à

l’emplacement de la prise murale et les précautions à prendre pour couper l’alimentation électrique

avant

d’effectuer les opérations d’entretien.

AVERTISSEMENT : Le non-respect des instructions du présent

manuel peut

être à l’origine d’un incendie ou explosion causant

des dommages matériels,

corporels ou le décès.

●

Ne pas entreposer ou utiliser d’essence ou autres gaz ou

liquides inflammables à proximité de cet ou

tout autre appareil.

2) QUE FAIRE SI ÇA SENT LE GAZ

-

N’allumez aucun appareil.

-

Ne touchez aucun interrupteur ; n’utilisez aucun téléphone se

trouvant dans le bâtiment.

-

Appelez immédiatement votre fournisseur de gaz utilisant le

téléphone d’un voisin.

Suivez les instructions données par le fournisseur de gaz.

-

Si vous n’arrivez pas à joindre votre fournisseur de gaz,

contactez les pompiers.

●

L’installation et la mise en service doivent être effectuées par

un installateur qualifié, un centre agréé

ou le fournisseur de

gaz.

●

Conservez les buses retirées de l’appareil en vue d’un usage futur.

●

La profondeur maximale des meubles installés au-dessus de la table de cuisson doit être de 13 pouces

(330 mm).

●

Maintenez à distance de l’appareil toute matière combustible, essence ou autres gaz et liquides

inflammables.

●

N’obstruez pas le débit de gaz ou les bouches d’aération.

●

Couper l’arrivée du gaz à l’appareil en fermant manuellement le robinet du gaz indépendant avant

d’effectuer tout essai de pression de l’installation d’arrivée du gaz avec des pressions d’essai égales ou

inférieures à 1/2 psi (3,5 kPa).

20

POSITION DES COMPOSANTS

MODÈLE : GC22SS MODÈLE :

GC527SS

GC5271W

GC5272B

No. de la pièce

Description

Chaleur fournie

1

Ultra rapide

11 000 Btu/h

2

Brûleur rapide 10 000 Btu/h

3 Brûleur auxiliaire 3 550 Btu/h

4

Brûleu

r semirapide

6 100 Btu/h

6-7

Grille

8

Manette de commande du brûleur n° 1

9 Manette de commande du brûleur n° 3

10

Manette de commande du brûleur n° 2

11

Manette de commande du brûleur n° 4

NOTE : Cet appareil a été conçu pour un usage domestique uniquement.

Avertissement : Lors du fonctionnement,

les

surfaces de travail de la zone de

cuisson

deviennent très chaudes : ne

laissez pas les

enfants s’approcher !

La page charge ...

Summit GC5272B2 Le manuel du propriétaire

Summit GC5272B2 Le manuel du propriétaire

dans d''autres langues

Documents connexes