Legrand Lighting Integrator DL Card Guide d'installation

Legrand
Marque
Legrand
Modèle
Lighting Integrator DL Card
Taper
Guide d'installation
Wattstopper
®
Lighting Integrator Dataline Link (DL) Card
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 25271 – 11/16 rev. 1
Catalog Number • Numéro de Catalogue • Número de Catálogo: DL Card
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
DESCRIPTION
Introduction
In some systems, the Dataline Link (DL) card may be supplied in place of the
Dataline Power Supply (DP) card. The DL card includes a dataline power
supply. Therefore, systems with a DL card do not require a separate DP card.
The DL card adds additional functionality to the LIC panel system. In some
cases, a system will be specified with more than one panel containing a DL card
or the system is using the HLINK. In these cases the HLINK will typically be
set as the master and the DL card(s) should be set as slaves. A DIP Switch is
provided on the DL card for this setting. See Figure 1.
Where a system has more than one DL card installed, each DL card must be
set to a different device number (1 - 9). This is set using the rotary dial labeled
SWT1 on the DL card. Most systems will have a single DL card, and this should be set to #1.
DIP Switches
1 ON = Master (this is a DL card responsible for time keeping for the entire system.
If there is only one DL card, set it to ON).
1 OFF = Slave (this is used for any additional DL cards-only one Master allowed)
2 ON = Global Switch Status Messages are repeated
2 OFF = Global Switch Status Messages are not repeated
3 ON = Unused
4 ON = This card powers the dataline. There can be only one source of dataline
power (usually the Master DL)
4 OFF = No dataline power (this is used for any additional DL cards (only one
powering the dataline is allowed)
Figure 1: DIP Switch
3
0
9
8
7
6
5
4
1
2
1 2 3 4
Figure 2: DL Card
800.879.8585
www.legrand.us/wattstopper
No. 25271 – 11/16 rev. 1
© Copyright 2016 Legrand All Rights Reserved.
© Copyright 2016 Tous droits réservés Legrand.
© Copyright 2016 Legrand Todos los derechos reservados.
Wattstopper warranties its products to be free
of defects in materials and workmanship for a
period of five (5) years. There are no obligations
or liabilities on the part of Wattstopper for
consequential damages arising out of, or in
connection with, the use or performance of this
product or other indirect damages with respect
to loss of property, revenue or profit, or cost of
removal, installation or reinstallation.
Wattstopper garantit que ses produits sont
exempts de défauts de matériaux et de fabrication
pour une période de cinq (5) ans. Wattstopper
ne peut être tenu responsable de tout dommage
consécutif causé par ou lié à l’utilisation ou
à la performance de ce produit ou tout autre
dommage indirect lié à la perte de propriété, de
revenus, ou de profits, ou aux coûts d’enlèvement,
d’installation ou de réinstallation.
Wattstopper garantiza que sus productos
están libres de defectos en materiales y mano
de obra por un período de cinco (5) años. No
existen obligaciones ni responsabilidades por
parte de Wattstopper por daños consecuentes
que se deriven o estén relacionados con el
uso o el rendimiento de este producto u otros
daños indirectos con respecto a la pérdida
de propiedad, renta o ganancias, o al costo
de extracción, instalación o reinstalación.
WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA
INSTALLING THE CARD
1. Pick a panel close to the center of the dataline, unless some other specific
location is required.
2. Remove power from that panel if not already done.
3. Unplug connector from the CC Card Dataline (In or Out)
4. Install the card in the slot immediately above the PS (Power Supply) card in the
desired LI-24 or LI 48 panel.
5. Apply power to that panel.
6. Observe the DL Card Dataline LED. It should be glowing green.
7. Observe the CC Card Dataline Status LED. It should be glowing green.
8. Restore any dataline connections to the CC Card in the panel.
9. Observe the CC Card Dataline Status LED in other panels. They should be
glowing green.
10. If this card is being used with WinControl, plug in a USB or RS232 cable to the
DL card.
11. If this card is being used with a remote dry-contact Alarm confirmation button,
attach it between COMMON and SWITCH on the Alarm Plug.
12. If this card is being used with a remote dry-contact Alarm feedback contact, attach
it between ALARM1 and ALARM2 on the Alarm Plug.
WARNING: TURN THE POWER OFF AT THE
CIRCUIT BREAKER BEFORE WIRING.
DL Card
  • Page 1 1
  • Page 2 2

Legrand Lighting Integrator DL Card Guide d'installation

Legrand
Marque
Legrand
Modèle
Lighting Integrator DL Card
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents