Blyss HT15SSR Manuel utilisateur

EN

DRY INERTIA CERAMIC HEATER

NT10SSR 840-1000W 3663602688600

NT15SSR 1250-1500W 3663602688631

NT20SSR 1680-2000W 3663602688662

Let’s

get started…

These instructions are for your safety. Please read through them thoroughly

before use and retain them for future reference.

Getting started…

02

Safety

Before you start

Quick start

03

06

11

In more detail…

17

Technical and legal information

Care and cleaning

18

22

23Environment protection

02EN

Safety

PLEASE READ SAFETY INSTRUCTIONS CAREFULLY

BEFORE USING THE UNIT.

This appliance can be used by children aged from 8

years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision

or instruction concerning use of the appliance in a

safe way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be

made by children without supervision.

Children of less than 3 years should be kept away

unless continuously supervised.

Children aged from 3 years and less than 8 years

shall only switch on/off the appliance provided that

it has been placed or installed in its intended normal

operating position and they have been given

supervision or instruction concerning use of the

appliance in a safe way and understand the hazards

involved.

Children aged from 3 years and less than 8 years

shall not plug in, regulate and clean the appliance

or perform user maintenance.

CAUTION — Some parts of this product can become

very hot and cause burns. Particular attention has to

be given where children and vulnerable people are

present.

03EN

Safety

If the power cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

The appliance should not be placed immediately

below a socket.

WARNINGS:

In order to avoid overheating, do

not cover the heater.

Do not use this heater with a programmer, timer,

separate remote control system or any other device

that turns on the heater automatically because

there is a risk of fire if the device is covered or

placed incorrectly.

CAUTION: To avoid hazard due to inadvertent

resetting of the thermal cutout, this appliance must

not be powered via an external switch, such as a

timer, or connected to a circuit that is regularly

switched on and off by the electricity supplier.

This heater must not be disposed of with household

waste; it must be taken to a local centre of

recovery and recycling of electrical appliances.

The heater must be installed so that switches and

other control devices can not be touched by a person

in the bath or shower.

A means of disconnection from the power supply

having a contact opening distance of all poles must

be included in the fixed wiring in accordance with

the installation requirements.

04EN

Safety

If being fitted in a bathroom, a 30mA RCD must

be used.

With respect to the details of how to install the

appliance onto the wall, refer to "INSTALLATION"

on pages 9-10.

05EN

For domestic use only.

Never allow children or persons unable to operate the

appliance safely to use this appliance without supervision.

Please dispose of plastic bags carefully and keep them

away from children.

This appliance is for indoor use only.

Observe the minimum distances as shown in Fig. 1.

Do not install the unit in place where air flow that may

disturb its regulation(e.g. under an air conditioning unit)

Before you start

The power connection is made by the 2 cables via a

connection box. In places such as wet bathroom,

laundry, kitchen, install the appliance at least 250 mm from

the level of the ground.

Things to check before you start

1. Body

2. Control panel

Your product

INSTALLING THE APPLIANCE?

3. Wall-mounted kits

2

1

06EN

Description Drawing QTY

Screw

Wall plug

4

3

Before you start

This heater is for wall mounting only. Do not attempt to use it

free standing.

You need to follow the below requirements when you install

your heater:

- Means for disconnection having a contact separation in all

poles must be incorporated in the fixed wiring in accordance

with the wiring rules.

- Warning: you need to connect the two conductors of the

supply cable to a connection block in respecting the

polarities as following:

IMPORTANT: The wires in the mains lead are coloured in

accordance with the following code:

Blue – Neutral

Brown – Live

The blue wire must be connected to the terminal marked with

an N or coloured black.

The brown wire must be connected to the terminal marked

with an L or coloured red.

WARNING: Never connect live or neutral wires to the earth

terminal.

This product is double insulated and must not be

earthed. If there are any incoming earth cables, they must be

joined together using a suitable connector (not supplied) and

well insulated with good quality insulation tape. This is to

ensure earth continuity throughout your property.

All fittings must be installed by a competent person in

accordance with the current IET Wiring Regulations

(BS7671). If in doubt, consult a qualified electrician.

THIS PRODUCT IS SUITABLE FOR BATHROOMS ZONE

2 AND OUTSIDE ZONE;

07EN

Before you start

This product is suitable for use in living areas, and Bathroom

dry (Outside) Zones only (see diagram below and current

IET Wiring Regulations for details). It is not suitable for

moisture is likely. If being fitted in a bathroom a 30mA RCD

must be used. This appliance does not come fitted/supplied

with a fused plug. DO NOT wire/fit a plug to this appliance.

The appliance must be electrical connected to a fused fixed

spur, which is fitted with a 13Amp fuse.

Always refer to the Reference Drawing for Bathroom

Installation.

Note: the below drawing is for reference only.

We suggest you to contact a professional electrician for any

help.

* Full details can be found in the current IET Wiring

Regulations (BS7671)

0.6m

ZONE

2

Window

recess

(DRY) OUTSIDE ZONES

ZONE

2

ZONE

1

2.25m

Ceiling

THIS PRODUCT IS SUITABLE FOR BATHROOMS

ZONE 2 AND OUTSIDE ZONE;

ZONE

0

Bathroom Zones 0,1, or other areas where contact with

08EN

Before you start

INSTALLATION

09EN

To hang the heater on the wall:

1. Choose a suitable installation location for the

heater. (Figure 1)

2. Disassemble the wall bracket by loosening the

screw (do not remove, only loosen) and slide the

metal plate out of the hole. Take out the bracket by

pulling down (Figure 2).

3. Verify that the bracket is horizontal with a spirit

level and mark the location of 4 holes on the wall.

Drill 4 holes in the wall using a drill adapted to

the diameter of wall plug. Insert the wall plug into

the holes,then screw securely wall mount bracket

onto the wall. (Figure 3)

4. Place the heater against bracket (Figure 4):

A : Align the heater on the 2 lower hooks that are

downwards.

B : Pull the heater upwards whilst retaining it in the

2 lower hooks.

C : Align the heater on the 2 upper hooks that are

upwards.

D : Pull the heater down.

5. Slide the metal plate into the hole, and fasten the

screw to lock the wall mount bracket (Figure 5).

Before you start

10EN

11EN

LCD display:

Quick start

Functions of the icons on the LCD:

Symbol Function

Mode standby (the appliance doesn’t work but with power on)

Mode Anti-freeze (the appliance maintains the temperature around 7°C)

Mode Comfort (set the desired temperature)

Mode ECO (ECO maintains the temperature that is 3.5 ° C lower to comfort temperature.

This mode reduces the temperature without disturbing the desired temperature in comfort

mode)

Temperature (centigrade)

Keyboard lock

Program modes or Fil pilote mode

Window detection mode

Heating indicator (When appliance is heating up, this icon will show on the screen.

The icon will disappear when detected temperature reach the set temperature.)

Weekly personalized modes:

Mode Comfort active

Mode eco active

12EN

I. Mode selection ( / button)

HOW TO USE

Quick start

CONTROL PANEL

When first use the machine, there will be some slight smell. It is normal. The smell will

disappear after heater working for an hour.

Button

MENU

OK

/

Function

Standby

Short press to enter setting menu: 1. Time setting; 2. program modes

setting; 3. presence detection mode.

Press for 3 seconds, activate/ inactivate keyboard lock.

Confirm button

Under working status: shift working mode (Comfort/Eco / Program modes

or Fil Pilote/ Window detection mode/ Anti-freeze)

Under setting status: shift options by left and right

Under working status: adjust temperature

Under setting status: shift options by up and down

BEFORE USING THE APPLIANCE, PLEASE OPEN THE LID OF THE CONTROL

PANEL.

/

1. For the first time you use the device, after you connect to the power supply and

after that the clock is set, the device will be in standby mode, and you can press the

standby button to enter comfort mode.

Press / to toggle among the modes: comfort / Eco / Program mode or Fil

Pilote / Window detection mode / Anti-freeze .

2. Program modes and Fil pilote share the same icon . And these 2 modes are

mutually exclusive. When the appliance is working on Program mode, press and hold OK

button for 3 seconds, the appliance will shift from Program mode to Fil pilote mode.

When the appliance is working on Fil pilote mode, press and hold OK button for 3

seconds, the appliance will shift from Fil pilote mode to Program mode.

The interface of program mode and Fil pilote mode are as below:

Note: For the program mode, mode setting and mode selection is separated. If you

want to set the program mode, press MENU to enter setting menu to choose

program mode setting and press OK to enter setting interface. For details, please

refer to part 2“Program mode setting”under section III“Setting menu”.

13EN

Quick start

Program mode Fil pilote

3. Fil-pilote mode

Press / button to choose mode (Program modes or Fil pilote mode). Under

Pilot mode, select the mode via the external control (for France only).

If the working interface is at Program mode, press and hold OK button for 3 seconds,

the appliance will shift from Program mode to Fil pilote mode.

For other countries except France, if you choose mode Fil pilote P, the appliance will

work at comfort mode as default.

4. Window detection mode

Press / button to enter window detector function. The appliance will enter comfort

mode as default. If temperature decrease detected, the appliance will automatically

enter anti-freeze mode. If temperature rises up, the appliance will go back to comfort

mode.

Notes: In case of power failure, the unit keep in memory only the parameters,

temperature and operating mode. When power is restored, the clock should be

adjusted again to operate the program modes properly.

14EN

II. Temperature setting

Quick start

REMARKS: under window function, pilot control is not available.

1. Under the mode of comfort or Eco (excluding anti-freezing mode), temperature is

adjustable. Press / to choose the desired temperature for comfort mode between

5°C and 29°C. The temperature difference between mode ECO and mode comfort is

3.5°C, so the temperature range of mode ECO is between 1.5°C and 25.5°C.

2. Press other buttons except / to finish the setting, or it will automatically save.

3. When the room temperature is higher than the selected temperature, the heater

will stop heating.

III. Setting menu (MENU button)

Press MENU to enter setting menu interface.

Press / or / to choose from time setting , program mode setting ,

motion sensor . The selected icon will flash while other icons keep on.

Press MENU to exit the setting menu or after 30 seconds it will automatically exit and

go back to working interface.

1. Time setting

Press MENU to enter setting interface, and / to choose time setting . When

is flashing, press OK to start time setting.

Press / to toggle among day of week, hour, and minute, and / to set day of

week, hour, and minute.

Press OK to confirm hour setting and move to minute setting 00-59.

15EN

Day of week Pre-set 24-hour

program P1-P7

Quick start

Press OK to confirm minute setting and move to day of week setting1-7.

Press OK to confirm or after 30 seconds, it will automatically save and go back to

working interface.

2. Program mode setting

Press MENU to enter setting interface, and / to choose program mode setting .

When is flashing, press OK to enter setting interface.

Under program mode, you can choose from 7 pre-set 24-hour programs (P1-P7) for

each day of week. The 7 pre-set 24-hour programs (P1-P7) are programable. For

each hour, you can choose between comfort mode and economic mode.

Under program mode, the default setting for day 1 to 7 of the week are as follows:

day 1 to day 5: work with P1,

day 6 to day 7: work with P3.

The default setting of P1-P7 are as follows:

Press / to choose day of week, and / to choose from 7 pre-set 24-hour

programs (P1-P7), Or press OK to confirm previous setting and enter setting for next

day. After setting of last day, press OK to confirm or after 30 seconds, it will

automatically save and go back to working interface.

P1

P2

P3

P4

P5

P6

P7

16EN

Hour

(01 is for hour 1 to hour 2, and so on,

24 is for hour 24 to hour 1)

Quick start

Setting of 7 pre-set 24-hour programs (P1-P7)

Under program mode setting interface, regardless of which day, when you choose

program from P1 to P7, press and hold OK for 3 seconds to enter the setting

interface of the mode. The setting will be memorized (in case of power failure, it will

also be memorized).

1. Press / to choose hour (1-24). Press to choose comfort mode. , to

choose economic mode .

2. After setting of 24 hours, it will automatically save and go back to previous setting

interface.

For example, if you enter the P3 setting from below interface (day 1, P3), it will go

back to below interface (day 1, P3) after you finish P3 24-hour setting.

Notes:

1. In case of power failure, the unit keep in memory only the parameters,

temperature and operating mode. When power is restored, the clock should be

adjusted again to operate the program modes properly.

2. After you finish program mode setting, it will be saved but will not

automatically start working at program mode. You need to press left/right arrow

button to choose program mode to make the heater work at this mode.

Keyboard lock

IV. Keyboard lock setting

Press MENU button for three seconds to activate the keyboard lock function , in

order to unlock, press MENU again for three seconds

5 Press / to exit motion sensor function and choose other modes.

17EN

Quick start

3. Motion sensor

Press MENU to enter setting interface, and / to choose motion sensor . When

is flashing, press OK to enter setting interface.

Press / or / to choose ON/OFF. Press OK to confirm and after 30 seconds, it

will automatically save and go back to working interface.

Remarks:

1) When motion sensor function is ON, the appliance will work at comfort mode as

default, with icon show on the screen.

2) Once absence is detected, it will automatically enter eco mode or anti-freeze

mode , with icon flashing.

3) At any time, once presence detected, the appliance will go back to comfort mode

, with kept on.

4) Detected distance and angles are indicated as follows:

60°

3m

18EN

Quick start

Remarks:

1. The keyboard lock function doesn’t lock the standby button.

2. The keyboard lock function will automatically be deactivated under below

circumstances.

1) the appliance is turned off by pressing standby button.

2) the appliance suffer power disconnection

Technical information

Care and cleaning

Environmental protection

18

22

23

In more detail…

19EN

Technical information

Technical Specifications

Model no. Voltage

& Frequency

Power

(Watt)

Product

Dimension

H x W x D

(mm)

Class

220-240V~

50Hz

220-240V~

50Hz

220-240V~

50Hz

IP

NT10SSR 840-1000W

1250-1500W

1680-2000W

580x600x120

Double isolation

CLASS II

IPX4

NT15SSR 580x720x120

Double isolation

CLASS II

IPX4

NT20SSR

580x840x120

Double isolation

CLASS II

IPX4

20EN

La page charge ...

Blyss HT15SSR Manuel utilisateur

Ce manuel convient également à

Blyss HT15SSR Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents