Haier AD09SL2VHA Installation Instructions Manual

Marque: Haier

Modèle: AD09SL2VHA

Catégorie: Climatiseurs split-system

Taper: Installation Instructions Manual

Ce manuel convient également à

31-5000099 08-19 GEA

Design may vary by model number. L’aspect peut varier selon le numéro de modèle. El diseño puede variar según el número de model.

Installation Instructions

Indoor Unit Installation

Slim Duct

31-5000099

This manual contains installation instructions for Slim Duct indoor units. For

the FlexFit series using other style indoor units, refer to the Installation Manual

supplied with the indoor unit.

31-5000099 3

Table of Contents

IMPORTANT SAFETY INFORMATION ..............................................................4

INSTALLATION INSTRUCTIONS ..................................................................5

Step 1 ....................................................................................8

Step 2 ....................................................................................9

Step 3 ...................................................................................13

Step 4 ..................................................................................16

LIMITED WARRANTY ......................................................................... 18

31-5000099

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

READ AND SAVE THESE INSTRUCTIONS

WARNING

For your safety, the information in this manual must be followed to minimize the risk of

fire, electric shock, or personal injury.

• Use this equipment only for its intended purpose as

described in this manual.

• This heat pump must be properly installed in

accordance with these instructions before it is used.

• All wiring should be rated for the amperage value

listed on the rating plate. Use only copper wiring.

• All electrical work must be completed by a qualified

electrician and completed in accordance with local and

national building codes.

• Any servicing must be performed by a qualified

individual.

• All air conditioners contain refrigerants, which

under federal law must be removed prior to product

disposal. If you are getting rid of an old product

with refrigerants, check with the company handling

disposal.

• These R-410A heat pumps systems require that

contractors and technicians use tools, equipment and

safety standards approved for use with this refrigerant.

DO NOT use equipment certified for R22 refrigerant

only.

WARNING

RISK OF ELECTRIC SHOCK. Could cause injury or death.

• An adequate ground is essential before connecting

the power supply.

• Disconnect all connected electric power supplies

before servicing.

• Repair or replace immediately all electrical wiring that

has become frayed or otherwise damaged. Do not

use wiring that shows cracks or abrasion damage

along its length or at either end.

WARNING

RISK OF FIRE. Could cause injury or death.

•

Do not store or use combustible materials, gasoline or

other flammable vapors or liquids in the vicinity of this

or any other appliance.

For any service which requires entry into the

refrigerant sealed system, Federal regulations

require that the work is performed by a technician

having a Class II or Universal certification.

31-5000099 5

Installation Instructions

FOR MORE HELP, VISIT HAIERAPPLIANCES.COM/DUCTLESS OR GEAPPLIANCES.COM/DUCTLESS

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT – Save these

instructions for local inspector’s use.

• IMPORTANT – Observe all governing

codes and ordinances.

• Note to installer – Be sure to leave these

instructions with the owner.

• Note to consumer – Keep these instructions for

future reference.

• Skill level – A licensed certified technician (to

handle refrigerant R-410A, recovery, etc) and a

qualified electrician are required for installation and

service of this split heat pump system.

• Use team lift for mounting the ducted unit.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the limited warranty.

• For personal safety, this system must be properly

grounded.

• Protective devices (fuses or circuit breakers)

acceptable for installation are specified on the

nameplate of each unit.

• Make sure to avoid wiring or plumbing inside the

wall when installing.

CAUTION

• Aluminum building wiring may present special

problems - consult a qualified electrician.

• When the unit is in the STOP position, there is still

voltage to the electrical controls.

31-5000099

Installation Instructions: List of Materials

Required Tools for Installation

Supplied with Unit

Supplied by Installer

• 17mm, 22mm, 26mm or Adjustable Wrench

• #2 Phillips Screwdriver

• Drill

• R-410A Approved Flaring Tool

• Hex Wrench

• Hole Saw 2 1/4”

• Level

• Manifold Gauge

• Measuring Tape

• Micron Gauge

• Mini-Split Adapter (5/16”F to 1/4”M)

• Nitrogen*

• Pipe Cutter

• Razor Knife

• Reamer

• Sealant, non-expanding (for lineset hole)

• Soap/water solution or gas leakage detector

• Stud Finder

• Torque Wrench and Back-up Wrench

• Vacuum Pump

• Wire Strippers

• Refrigerant Scale

• Usual and customary HVAC hand tools

• Condensate connecting tube

• Clamp

• Flare nuts (2)

• YR-E17 wired controller

• 15 ft cable

• Insulation

• Insulated copper tubing • 14/4 (14 gauge – 4 conductor) stranded cable

• 3/4 inch PVC for condensate

• Insulation for condensate drain

• 3/8 threaded rod, washers and nuts

• 410A Refrigerant

Model Liquid (inch) Vapor (inch)

AD07SL2VH(A)/(B) 1/4 3/8

AD09SL2VH(A)/(B) 1/4 3/8

AD12SL2VH(A)/(B) 1/4 3/8

AD18SL2VH(A)/(B) 1/4 1/2

AM24LP2VHA 3/8 5/8

AM36LP2VHA 3/8 5/8

AM48LP2VHA 3/8 5/8

31-5000099 7

Installation Instructions: Introduction and Overview

Ducted Product Information

The ducted indoror unit is shipped with a wired remote

controller.

The Ducted unit will install above the ceiling or in a

soffit area. It is mounted using threaded rods that fit

into brackets that are located at all four corners of the

Ducted assembly.

The slim duct unit has a built-in condensate pump

and a float switch to avoid overflow situation and

maintaining reliable operation. An insulated condensate

fitting is included in the accessory pouch. This fitting

connects the condensate drain outlet of the unit to the

field-supplied drain piping.

When making refrigerant line connections, always use

the flare nuts provided with this equipment. Refrigerant

line connections should be wrapped with insulating tape

at the slim duct indoor unit to prevent sweating

YR-E17 Wired Controller

See wired controller manual

for more information

31-5000099

Installation Instructions: Introduction and Overview

Condensate Handling

The Ducted unit has a built-in condensate pump

and water level safety switch. There are also two

optional ports for gravity drainage. The condensate

pump is rated to lift water up to 27” from the point

of discharge on the Ducted unit. (This number may

vary.)

The Ducted unit comes with a grey connection hose

and clamp. This hose is connected to the Ducted

unit condensate discharge hose port. The other end

of the hose is sized to accept 3/4 inch PVC piping.

Recommended condensate piping configurations are

shown here:

Electrical Power

Follow all local codes and regulations when installing

electrical wiring.

Route required electrical power to area where the

Ducted unit is to be located. Maintain at least a 10 foot

separation between TV, Radio or any communication

wiring and the power to the indoor unit.

14 Gauge stranded copper wire should be used to

make the electrical connection and communication link

between indoor and outdoor units.

The wiring is connected at the indoor unit electrical

terminal blocks screws 1, 2, 3 and ground. There

should be no splices in the wires between the indoor

and outdoor units as these serve as communication

signal wires and electrical power connections. Any

accessory added to shut off power to the indoor

section should break the Number 2 terminal only.

Air Delivery Clearances

Make certain to maintain proper clearances around the

Ducted unit.

Inadequate clearances can cause system freezing and

temperature control problems.

Service and Maintenance Clearances

Make sure there are adequate clearances for future

maintenance and service. Allow enough room to

access the condensate pump assembly and the

electrical control box.

12 in. below

3-5 ft.

11 in. under

8.6 in.

19.6 in. below

31-5000099 9

MINIMUM CLEARANCES (Appearance may vary)

This picture is for reference only. Your product may look different.

Installation Instructions

Step 1 - Preparation

A. Procedure for selecting the location:

• Place above the ceiling or in soffit area where you

have enough space to position the unit.

• Place where the drainage pipe can be properly

positioned.

• Place where the inlet and outlet air of the indoor unit

will not be blocked.

• Do not install the unit in a place with heavy oil or

moisture (e.g. - kitchens and workshops)

• Do not install in a location with destructive gas (such

as sulfuric acid gas) or pungent gas (thinner and

gasoline) are used or stored.

• Choose a place solid enough to bear the weight and

vibration of the unit and where the operation noise will

not be amplified.

• The unit in a location which will not adversely

affect occupants, building components, or valuable

possessions.

• Leave enough space for maintenance.

• Install at least 3 ft. away from sources that may create

electronic interference.

NOTES:

• R-410A refrigerant is a safe, nontoxic and

nonflammable refrigerant. However, if there is a

concern about refrigerant concentration in the case

of leakage, add extra ventilation.

B. Rod Mounting Information:

The Ducted unit should be mounted to the building

structure using threaded rods. The threaded rods

should have washers and nuts to allow the height

and level of the Ducted unit to be adjusted.

The threaded rods and attachment brackets are field

supplied items. The materials required for mounting

to the brackets on the Ducted unit include:

• 4- 3/8” Threaded Rods

• 4- Mounting Brackets

• Washers

• Nuts (Double shown in step 2C)

Model A - Inches (mm) B - Inches (mm)

AD07SL2VHA 35 1/8 (892) 14 1/2 (369)

AD07SL2VHB 35 1/8 (892) 14 1/2 (369)

AD09SL2VHA 35 1/8 (892) 14 1/2 (369)

AD09SL2VHB 35 1/8 (892) 14 1/2 (369)

AD12SL2VHA 35 1/8 (892) 14 1/2 (369)

AD12SL2VHB 35 1/8 (892) 14 1/2 (369)

AD18SL2VHA 47 3/4 (1213) 14 1/2 (369)

AD18SL2VHB 47 3/4 (1213) 14 1/2 (369)

AM24LP2VHA 39 (990) 23 1/2 (595)

AM36LP2VHA 61 1/4 (1556) 25 3/4 (653)

AM48LP2VHA 61 1/4 (1556) 25 3/4 (653)

Air Flow

> 12 in

> 6 in

31-5000099

Installation Instructions

F. Connect the grey flexible drain hose supplied with

the Ducted unit to the condensate pump discharge

pipe of the Ducted unit. Tighten the clamp securely.

Using 3/4 “ PVC, connect the flexible hose to the

building’s condensate drain system.

Step 2 - Installation of the Slim Duct Unit

A. Determine and mark the position of where the

Ducted unit is to be installed. Install the hardware

necessary to mount the threaded rods. Always

select a location strong enough to support the Slim

Duct unit.

B. Install threaded rods to the hardware attached to

the structure.

D. Using a level, adjust the nuts on the threaded rods

to obtain level readings both side to side and front

to back on the Ducted unit.

Lift the Ducted unit and position the threaded rods

into the 4 mounting clips, one located on each corner

of the unit.

Ream both inside and outside of the refrigerant

tubing where a cut has been made. Use every

precaution to ensure reamed copper chips not to

lodge inside the tubing.

Install the factory-supplied flare nuts on the

refrigerant tubing using an R-410A flaring tool

ONLY. Apply a small amount of refrigerant oil to

the back of the flare and threads.

Tighten the flares with a torque wrench and back-

up wrench to the specifications found in the outdoor

unit Installation Manual.

31-5000099 11

Step 2 - Installation of the Slim Duct Unit (Cont.)

G. Route the 14AWG stranded 4 conductor power/

communication cable and the wired remote

cable to the air handler. Use reducing washers

and appropriate connector to attach the power/

communication cable to the unit. The wired remote

cable will enter the unit through a rubber grommet.

The 4 conductor cable connects to the terminal block

at terminals 1, 2, 3, and ground. The wired remote

cable connects to the air handler main board at

connector CN1. Re-install electrical box cover.

Installation Instructions

H. The unit is now ready for connection to the

ductwork. The return air duct can be configured

as either a rear inlet or bottom inlet.

Rear side air inlet

Bottom side air inlet

Diffuser

Return Duct

Diffuser

Return Duct

31-5000099

Installation Instructions

Step 3 - Electrical Connections

Step 4 - Leak Testing and Evacuation

Electrical Connections Indoor and Outdoor Units

14AWG stranded copper wire only. (Central Controller Not Used)

Maintain 10 feet of distance from TV, Radio or any communication wiring.

NOTE: The Slim Duct unit ships with the YR-E17 wired controller. SeeWired Controller

manual for more information..

Refer to the outdoor section Installation Manual for the recommended procedure.

Outdoor unit

Power

Wiring

)

(

)

(

)

(

)

(

)

(

Indoor unit

3wire 14AWG

Control Wiring

31-5000099 13

Limited Warranty

Staple your receipt here. Proof of the original purchase

date is needed to obtain service under the warranty.

• Damage from improper installation.

• Damage in shipping.

• Defects other than from manufacturing (i.e.,

workmanship or materials).

• Damage from misuse, abuse, accident, alteration, lack

of proper care and/or regular maintenance, or incorrect

electrical voltage or current.

• Damage resulting from floods, fires, wind, lightning,

accidents or similar conditions.

• Damage from installation or other services performed

by other than a licensed HVAC technician.

• Labor and related services for repair or installation of

the Product.

• A Product purchased from an online retailer.

• Damage as a result of subjecting Product to an

atmosphere with corrosives or high levels of

particulates (such as soot, aerosols, fumes, grease).

• A Product sold and/or installed outside of the 50 United

States, the District of Columbia, or Canada.

• Batteries for the controller and other accessories

provided with the Product for installation (e.g., plastic

hose).

• Normal maintenance, such as cleaning of coils, cleaning

filters, and lubrication.

• For Product installed in non-owner occupied

applications, Product that has not been maintained

annually by a licensed HVAC technician (proof required).

For The Period Of: GE Appliances, a Haier company Will Replace:

5 year limited parts

warranty

From the date of the

original purchase

This limited warranty cover all defects in workmanship or material for the mechanical and

electrical parts contained in the Product (“Defective Parts”) for a period of 5 years from the

Date of Purchase. Haier will provide new or refurbished parts, or a replacement for all or part

of the unit, at its sole discretion, to your licensed HVAC technician installer. This warranty also

covers all defects in workmanship or material for the unit controller for a period of 1 year. The

remote controller is covered by 1-year accessory warranty. The ductless system is covered

by standard warranty. Haier will provide a new or refurbished controller, at its sole discretion.

7 year compressor

warranty

from the date

of the original purchase

The compressor contained in this product is warrantied for a period of 7 years from the Date

of Purchase. Haier will provide a new or refurbished compressor, or a replacement for all or

part of the unit, at its sole discretion, to your licensed HVAC technician installer.

For the product models listed on Attachment 1 (the “Product”), this Standard Limited Warranty is provided to the Original

Owner of the Product:

WHAT IS THE DATE OF PURCHASE

WHO IS COVERED

HOW CAN YOU GET SERVICE

THIS WARRANTY DOES NOT COVER

The “Date of Purchase” is the date that the original installation is complete and all product start-up procedures have

been properly completed and verified by the installer’s invoice. If the installation date cannot be verified, then the

Date of Purchase will be sixty (60) days after the manufacture date, as determined by the Product’s serial number. You

should keep and be able to provide your original sales receipt from the installer as proof of the Date of Purchase. In new

construction, the Date of Purchase will be the date the owner purchased the residence from the builder.

Contact your licensed HVAC technician installer. All installation and service must be performed by a licensed HVAC

technician. Failure to use a licensed HVAC technician for installation of this Product voids all warranty on this Product..

Owner occupied: The “Original Owner” of this product, which means the original owner (and his or her spouse) of the

residence where the Product was originally installed. Subject to the law of the state or province where the Product is

installed, this warranty is not transferable to subsequent owners or if the product is moved to a different residence after

the initial installation. Non-owner occupied: This limited warranty is provided for product 1) installed in a) single family

or multi-family non-owner occupied residential buildings, or b) non-industrial commercial applications, (such as office

buildings, retail establishments, hotels/motels) where the product is not subjected to an atmosphere with corrosives or

high levels of particulates (such as soot, aerosols, fumes, grease), and 2) if the product is maintained annually by a licensed

HVAC technician (proof of annual maintenance is required). The “Original Owner” of the product, means the original

owner of the building where the product was originally installed. For new construction, the purchaser of the building

from the builder will also be considered an original owner. This warranty is not transferable to subsequent owners or if the

product is moved to a different location after the initial installation.

31-5000099

10 YEAR STANDARD REGISTERED LIMITED WARRANTY

ATTACHMENT 1

THIS LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING

THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

All “Indoor and Outdoor Products,” identified in Attachment 1, registered by the installer or the Original Owner within 60

days of the Date of Purchase shall receive a Standard Registered Limited Warranty, which shall be identical to the Standard

Base Warranty, except that the Limited Parts Warranty shall be for a term of 10 Years and the Limited Compressor Warranty

shall be for a term of 10 years. All Product not registered within 60 days of the Date of Purchase shall be subject to the

Standard Base Warranty. Some states and provinces do not allow warranty terms to be subject to registration; in those

states and provinces the longer terms for Limited Parts Warranty and the Limited Compressor Warranty apply.

The remedy provided in this warranty is exclusive and is granted in lieu of all other remedies. This warranty does not cover

incidental or consequential damages. Some states and provinces do not allow the exclusion of incidental or consequential

damages, so this limitation may not apply to you. Some states and provinces do not allow limitations on how long an implied

warranty lasts, so this limitation may not apply to you. This warranty gives you specific legal rights and you may also have

other rights which vary by state and province. This warranty covers units within the 50 United States, the District of Columbia

and Canada. This warranty it provided by GE Appliances a Haier company, Louisville, KY 40225.

The “Product” is defined as Haier brand Ductless Split Units. The “Product” contains 2 sub-categories of goods: “Indoor and

Outdoor Products” and “Selected Installation Products,” which are further defined below: “Indoor and Outdoor Products”

can further be identified by the following model number descriptions: 1U*, 2U*, 3U*, 4U*, AB*, AD*, AL*, AM*, AW*, AF*,

MVA* MVH* “Selected Installation Products,” identified by the following model number descriptions: PB-* FQG-*, AH1-*,

MS1-* and MS3-*

Limited Warranty

31-5000099 15

Table des matières

CONSIGNES DE SÉCURITÉ IMPORTANTES ...................................................... 22

INSTRUCTIONS D’INSTALLATION .............................................................. 23

Étape 1 ................................................................................. 27

Étape 2 ................................................................................. 28

Étape 3 ................................................................................. 31

Étape 4 ................................................................................ 34

GARANTIE LIMITÉE .......................................................................... 35

31-5000099

CONSIGNES DE SÉCURITÉ IMPORTANTES

LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER L’APPAREIL

AVERTISSEMENT

Pour votre sécurité, les renseignements dans ce manuel doivent être observés afin de

minimiser le risque d’incendie, de décharge électrique ou de blessure.

• Utilisez cet équipement uniquement aux fins auxquelles il

est fait mention dans ce manuel d’utilisation.

• Avant son utilisation, ce climatiseur doit être installé

correctement en conformité avec les instructions

d’installation.

• Tout le câblage doit présenter des valeurs nominales

compatibles avec l’alimentation électrique spécifiée sur la

plaque signalétique. Utilisez seulement du fil de cuivre.

• Toute la partie électrique de l’installation doit être exécutée

par un électricien agréé selon les codes de l’électricité local

et national.

• Toute réparation doit être effectuée par une personne

qualifiée.

• Tous les climatiseurs contiennent un frigorigène qu’il

faut retirer avant de disposer du produit en vertu de la

loi fédérale. Si vous vous débarrassez d’un produit qui

contient un frigorigène, informez-vous auprès de l’organisme

responsable d’en disposer.

• Ces systèmes de climatisation R-410A exigent que les

entrepreneurs et les techniciens utilisent des outils, des

équipements et des normes de sécurité approuvés pour ce

type de frigorigène. N’utilisez PAS un équipement certifié

pour le frigorigène R22 seulement.

AVERTISSEMENT

RISQUE DE CHOC ÉLECTRIQUE. Peut occasionner une blessure ou la mort.

•

Une mise à la terre est essentielle avant de brancher

l’alimentation électrique.

•

Coupez l’alimentation électrique à la source avant de

procéder à une réparation ou un entretien.

•

Réparez ou remplacez immédiatement tout câblage électrique

usé ou autrement endommagé. N’utilisez pas un câblage

qui présente des fissures ou des marques d’abrasion sur sa

longueur ou l’une de ses extrémités.

AVERTISSEMENT

RISQUE D’INCENDIE. Peut occasionner une blessure ou la mort.

•

Abstenez-vous d’entreposer ou d’utiliser des matières

combustibles, de l’essence ou d’autres vapeurs ou liquides

inflammables à proximité de cet appareil ou de tout autre.

LISEZ ET CONSERVEZ CES INSTRUCTIONS

Si une réparation exige de pénétrer dans le

système de frigorigène étanche, la réglementation

fédérale impose de faire réaliser le travail par

un technicien de Classe II ou détenant une

certification universelle.

31-5000099 17

Instructions d’installation

POUR OBTENIR DE L’AIDE SUPPLÉMENTAIRE, VISITEZ HAIERAPPLIANCES.COM/DUCTLESS OU

GEAPPLIANCES.COM/DUCTLESS

AVANT DE COMMENCER

Veuillez lire toutes ces instructions attentivement.

• IMPORTANT – Conservez ces

instructions à l’usage de l’inspecteur local.

• IMPORTANT – Observez tous les

codes et ordonnances en vigueur.

• Note à l’installateur – Assurez-vous de laisser ces

instructions au propriétaire.

• Note au consommateur - Conservez ces instructions

pour référence ultérieure.

• Niveau de compétence – Un technicien (pour manipuler

le frigorigène R-410A, récupération, etc.) et un électricien

agréés sont requis pour l’installation y servicio de ce

climatiseur à deux blocs.

• Utilisez le lève-personne pour monter l’unité canalisée

• L’exactitude de l’installation est la responsabilité de

l’installateur.

• La garantie ne couvre pas les défectuosités du produit

causées par une installation inadéquate.

• Pour votre sécurité, ce produit doit être correctement mis

à la terre.

• Les dispositifs de protection (fusibles ou disjoncteurs)

admissibles pour l’installation sont spécifiés sur la plaque

signalétique de chaque unité.

. • Si une réparation exige de pénétrer dans le système de

frigorigène étanche, la réglementation fédérale impose

de faire réaliser le travail par un technicien de Classe II

ou détenant une certification universelle.

ATTENTION

• N’utilisez pas un cordon de rallonge avec ce système.

• Le câblage de bâtiment en aluminium peut présenter

des problèmes particuliers, veuillez consulter un

électricien agréé.

31-5000099

Instructions d’installation: Liste du matériel

Outils nécessaires pour l’installation

Fourni avec l’appareil

Fourni par l’installateur

• Clé 17 mm, 22 mm, 26 mm ou clé réglable

• Tournevis à tête cruciforme no 2

• Perceuse

• Outil à évaser approuvé pour R-410A

• Clé hexagonale

• Scie-cloche 2 1/4 po

• Niveau

• Manomètre de pression d’admission

• Ruban à mesurer

• Microvacuomètre

• Adaptateur « mini-split » (5/16 po F à 1/4 po M)

• Azote*

• Coupe-tube

• Couteau utilitaire

• Alésoir

• Scellant, non expansif (pour trou de tubulure)

• Solution d’eau savonneuse ou détecteur de fuite de

gaz

• Localisateur de montants

• Clé dynamométrique et clé d’appoint

• Pompe à vide

• Pinces à dénuder

• Balance de réfrigérant

• Outils manuels habituels en CVC

• Tube de raccord pour condensat

• Bride

• Raccords coniques (2)

• Commande câblée YR-E17

• Câble 15 pi (4,6 m)

• Isolant

• Tuyau de cuivre isolé • Câble toronné 14/4 (calibre 14 – 4 conducteurs)

• PVC 3/4 po pour condensat

• Isolant pour drain à condensat

• Tige filetée 3/8, rondelles et écrous

• Frigorigène 410A

Modèle Liquide (po) Vapeur (po)

AD07SL2VH(A)/(B) 1/4 3/8

AD09SL2VH(A)/(B) 1/4 3/8

AD12SL2VH(A)/(B) 1/4 3/8

AD18SL2VH(A)/(B) 1/4 1/2

AM24LP2VHA 3/8 5/8

AM36LP2VHA 3/8 5/8

AM48LP2VHA 3/8 5/8

31-5000099 19

Instructions d’installation:

Introduction et vue d’ensemble

Informations sur le produit à conduits

L’unité intérieure à conduits est livrée avec une

commande à distance câblée.

L’unité à conduits sera installée au-dessus du plafond

ou dans une zone de soffite. Elle est montée avec des

tiges filetées qui se placent dans des supports situés à

tous les quatre coins de l’assemblage à conduits.

L’unité à conduits étroits comporte une pompe à

condensat intégrée et un interrupteur à flotteur pour

éviter les débordements et maintenir un fonctionnement

fiable. Un raccord pour condensat isolé est inclus dans

la trousse d’accessoires. Ce raccord connecte la sortie

du condensat de l’unité au tuyau de vidange acheté

localement.

Lors de la réalisation des raccordements de la conduite

de réfrigérant, utilisez toujours les raccords coniques

fournis avec cet équipement. Les raccords de la

conduite de réfrigérant doivent être enveloppés du

ruban isolant au niveau de l’unité intérieure à conduits

étroits afin de prévenir le suintement.

Commande câblée YR-E17

Consultez le manuel de la

commande câblée pour des

renseignements supplémentaires.

31-5000099

Instructions d’installation:

Introduction et vue d’ensemble

Gestion du condensat

L’unité à conduits comporte une pompe à condensat

intégrée et un interrupteur de sécurité du niveau

d’eau. Elle est aussi dotée de deux orifices facultatifs

pour l’évacuation par gravité. La pompe à condensat

est homologuée pour monter l’eau jusqu’à 27 po (68,6

cm) depuis le point d’évacuation sur l’unité à conduits.

(Ce chiffre peut varier.)

L’unité à conduits est livrée avec un flexible de

raccordement gris et une bride. Ce flexible est

raccordé à l’orifice pour flexible d’évacuation du

condensat de l’unité à conduits. L’autre extrémité du

flexible est dimensionnée pour accepter un tuyau PVC

de 3/4 po.

Les configurations de tuyauterie du condensat

recommandées sont indiquées ici:

Alimentation électrique

Suivez tous les codes et règlements locaux lorsque

vous installez le câblage électrique.

Acheminez l’alimentation électrique requise vers

la zone où l’unité à conduits est située. Maintenir

au moins une séparation de 10 pi (3 m) entre le

câblage de la télévision, la radio ou tout câblage de

communication et l’alimentation à l’unité intérieure.

Un câble toronné en cuivre de calibre 14 doit être

utilisé pour effectuer les connexions électriques et le

lien de communication entre les unités intérieure et

extérieure.

Le câblage est connecté au vis 1, 2, 3 du bornier de

l’unité intérieure et à la terre. Il ne doit pas y avoir

d’épissures dans les fils entre les unités intérieure

et extérieure car ils acheminent les signaux de

communication et l’alimentation électrique. Tout

dispositif ajouté pour couper le courant à la section

intérieure doit couper la borne numéro 2 seulement.

Dégagements pour la circulation d’air

Assurez-vous de maintenir les dégagements

appropriés autour de l’unité à conduits.

Des dégagements inappropriés peuvent causer le

gel du système et des problèmes de contrôle des

températures.

Dégagements pour réparation et entretien

Assurez-vous de procurer les dégagements

appropriés pour l’entretien et les réparations à venir.

Allouez suffisamment d’espace pour accéder à la

pompe de condensat et au boîtier de commandes

électriques.

12 in. below

3-5 ft.

11 in. under

8.6 in.

19.6 in. below

La page charge ...

Haier AD09SL2VHA Installation Instructions Manual

Marque: Haier

Modèle: AD09SL2VHA

Catégorie: Climatiseurs split-system

Taper: Installation Instructions Manual

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Haier AD09SL2VHA
español: Haier AD09SL2VHA

Haier AD09SL2VHA Installation Instructions Manual

Ce manuel convient également à

Haier AD09SL2VHA Installation Instructions Manual

dans d''autres langues

Autres documents