Broan ZB110M Guide d'installation

ZB80M n ZB110M

X2 | Multi-Speed

Ventilation Fan

with Motion Sensor

INSTALLATION GUIDE

READ AND SAVE THESE INSTRUCTIONS

Installer: leave this guide with homeowner.

Register your product online at www.broan.com/register.

Easy installation in both

new construction and retrofit

Table of Contents

Warnings and Cautions 2

Typical Installation 2

New Construction Installation 3

Retrofit Installation 7

Operation 12

Cleaning and Maintenance 12

Troubleshooting 12

Service Parts 13

Warranty 14

ZB80M

n

ZB110M Installation Guide

Page 2

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and

Air Conditioning Engineers (ASHRAE), and the local code

authorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Use only ON/OFF switch, mechanical timer or relay-switched

control.

8. Acceptable for use over a tub or shower when connected to

a GFCI (Ground Fault Circuit Interrupter) - protected branch

circuit.

9. This unit must be grounded.

Typical Installation

CAUTION

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

2. This product is designed for installation in flat ceilings. Sensor

will not function reliably if product is not installed in flat ceiling.

DO NOT MOUNT THIS PRODUCT IN A WALL.

3. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

4. Please read specification label on product for further

information and requirements.

45° 45°

• Installation is the same for:

• Fits in 2" x 8" ceiling construction.

• Infinitely adjust the fan position

between joists from 14" to 24"

on center.

*Purchase

separately.

INSULATION*

(Place around and

over Fan Housing.)

ROOF CAP*

(with built-in

damper)

FAN

HOUSING

POWER

CABLE*

ROUND

DUCT*

ROUND

ELBOWS*

Seal gaps

around

Housing.

Seal duct

joints with

tape.

OR

Keep duct

runs short.

WALL CAP*

(with built-in

damper)

NOT FOR USE IN A COOKING AREA

Do not install above or inside this area

Floor

Cooking

Equipment

Joists I-Joists Trusses

The ducting from this fan to the outside of the building has a strong effect on the air flow, noise and en-

ergy use of the fan. Use the shortest, straighest duct routing possible for best performance, and avoid

installing the fan with smaller ducts than recommended. Insulation around the ducts can reduce en-

ergy loss and inhibit mold growth. Fans installed with existing ducts may not achieve their rated airflow.

6-inch round rigid metal duct is recommended for best performance.

ZB80M

n

ZB110M Installation Guide

Page 3

1

2

3

4

New Construction Installation

Tools needed

• Power screwdriver with a Phillips bit

• Phillips screwdriver

• Flathead screwdriver

• Pliers

• Wire insulation stripper

• Wire cutter

Materials needed

• 6" round metal ducting recommended for best performance.

Use of other ducting is acceptable but may impact performance.

• Roof cap or wall cap (built-in damper recommended)

• Tape to seal duct connections

• Electrical wiring and supplies per local code requirements

1

Remove Packaging

2

Install

Mounting

Frame

Parts Bag holds

Knockout Plate

and six (6)

screws

Remove

Instruction

Sheet

Punch out Mask from

packaging. See Step 6.

ZB80M

n

ZB110M Installation Guide

Page 4

3

1

4

2

1

2

3

New Construction Installation

3

Snap-in and

Secure Housing

4

Attach Duct Connector and Ducting

Position Housing

between joists and

crimp channel on both

sides of Mounting Frame

to lock Housing in place.

Do not crimp Housing.

Screws from Parts Bag

Top and bottom flanges

go outside Housing

Insert tab into slot

inside Housing

Screw from

Parts Bag

6" to 4" Reducer (for Model ZB80M only)

Tape

6" Ducting

4" Ducting

snap!

ZB80M

n

ZB110M Installation Guide

Page 5

3

4

1

2

New Construction Installation

5

Connect Wires and Install Knockout Plate

• Run 120VAC electrical wiring to the installation location.

• Use proper UL-approved connectors to secure wiring to the Knockout Plate provided in Parts Bag.

• Connect wires as shown in wiring diagram.

Screw from

Parts Bag

Attach cable clamp to Knockout

Plate. Knockout Plate mounts to

outside of Housing and may be

oriented as desired.

Connect wires

FAN

SENSOR/

CONTROL

BLK

WHT

BLK

ORG

BRN

MASTER MANUAL-ON

GRD

WHT

BLK

GRD

WHT

BLK

BLU

120 VAC

LINE IN

STANDARD OR MULTI-

FUNCTION WALL SWITCHES

RED

14/4

(IF ALL

WALL SWITCH

OPTIONS

ARE USED)

SENSOR/

CONTROL

RED

MASTER

ON/OFF

SWITCH*

MANUAL

ON

SWITCH*

KNOCKOUT

PLATE

RECEPTACLES

120 VAC

LINE IN

SWITCH BOX

BLACK

WHITE

RED

BLUE

*

purchase separately

SENSOR

CONTROL

SWITCH*

GROUND

(green or bare)

ORANGE

BROWN

• See OPERATION section on page 12

for details.

• MASTER switch turns fan system

on and shuts it off for fan cleaning and

maintenance purposes.

• SENSOR/CONTROL switch turns

motion control automatic operation on/off.

• MANUAL-ON switch directly increases

fan operation to certified airflow rate.

• MASTER and SENSOR/CONTROL

switches can be combined (see page 10).

• MASTER switch along with or separate

from SENSOR/CONTROL switch may be

located where it is not easily accessed

for everyday usage; they may need to

be labeled and located where it can’t be

turned on without being seen from fan to

comply with local and national codes.

ZB80M

n

ZB110M Installation Guide

Page 6

1

3

2

New Construction Installation

6

Insert Mask and

Finish Ceiling

7

Install Grille

See Page 12 for Operations, Cleaning and Maintenance, and Troubleshooting.

Mask protects unit

during construction.

Remove before

installing Grille.

• Install ceiling material.

• Cut out around Housing.

Plug in

Sensor

CAUTION

If the blower was unplugged, power must be

disconnected (see page 2, WARNING item 2)

before inserting motor plugs into control assembly.

IN ORDER TO PREVENT MOTOR/CONTROL DAMAGE:

ZB80M

n

ZB110M Installation Guide

Page 7

12" (30.5 cm)

1

2

Retrofit Installation

Parts Bag holds

Knockout Plate

and six (6)

screws

Existing ductwork and

wiring left in place

11" (27.9 cm)

parallel with joists

WARNING

Before removing existing fan, switch power off at service panel and lock the service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

Examine the existing wiring to make sure it is not damaged. If any damage is found,

DO NOT CONTINUE INSTALLATION of this product. Contact a qualified person(s) for repair.

Remove

Instruction

Sheet

Punch out Mask from

packaging. See Step 12.

1

Remove Packaging

2

Switch Off Power

4

Examine Wiring

3

Enlarge Ceiling Opening and Remove Existing Fan

• Ruler

• Pencil

• Drywall saw

• Claw hammer or pry bar

• Utility knife

Materials needed

• Tape to seal duct connections

• Existing rigid duct will require the

addition of a short length of flexible duct

• Electrical wiring and supplies per

local code requirements

Tools needed

• Power screwdriver with a Phillips bit

• Phillips screwdriver

• Flathead screwdriver

• Pliers

• Wire insulation stripper

• Wire cutter

ZB80M

n

ZB110M Installation Guide

Page 8

2

1

2

3

4

5

1

2

3

Retrofit Installation

5

Remove Blower Assembly

6

Remove Wiring Panel

7

Insert

Mounting

Frame

Both sides

Set aside

Blower

Assembly

Set aside

Wiring Panel

Set aside

screw

Bend up

four tabs

Remove screws from

Mounting Frame

and set aside

ZB80M

n

ZB110M Installation Guide

Page 9

1

2

1

3

4

Retrofit Installation

Screw from

Parts Bag

Screws set

aside

in Step 7

Pull existing wiring into

Housing as it is inserted

into Mounting Frame

Pull existing

ductwork

into Housing

Insert tab into

slot inside

Housing

10

Attach Ducting and Duct Connector

8

Secure

Mounting

Frame

9

Snap-in Housing

snap!

6" to 4" Reducer (for Model ZB80M only)

Tape

6" Ducting

4" Ducting

ZB80M

n

ZB110M Installation Guide

Page 10

2

1

4

5

6

3

Retrofit Installation

11

Install Knockout Plate, Connect Wires and Reinstall Wiring Panel

Screw from

Parts Bag

Attach cable clamp to Knockout

Plate. Knockout Plate mounts to

inside of Housing and may be

oriented as

desired.

Connect

wires

Screw set

aside in

Step 6

• Use proper UL-approved connectors to secure wiring to the Knockout Plate provided in Parts Bag.

• Connect wires as shown in wiring diagram.

FAN

SENSOR/

CONTROL

BLK

WHT

BLK

ORG

MASTER

WALL

SWITCH

GRD

WHT

BLK

GRD

WHT

BLK

BRN

120 VAC

LINE IN

14/2

RED

MASTER

WALL

SWITCH*

KNOCKOUT

PLATE

RECEPTACLES

120 VAC

LINE IN

SWITCH BOX

BLACK

WHITE

*

purchase separately

GROUND

(green or bare)

ORANGE

BROWN

• See OPERATION section on page

12 for details.

• MASTER switch turns fan system

on along with motion control and shuts

them off for cleaning and maintenance

purposes.

• MASTER switch may be located where

it is not easily accessed for everyday

usage; it may need to be labeled and

located where it can’t be turned on without

being seen from fan to comply with local

and national codes.

ZB80M

n

ZB110M Installation Guide

Page 11

1

3

2

Retrofit Installation

12

Reinsert and Secure Blower Assembly

13

Install Grille

If ceiling repairs are needed, place Mask in

Housing after Blower Assembly is secured.

See New Construction Installation Step 6.

Remove Mask before installing Grille.

Screws from Parts Bag

Plug in

Sensor

CAUTION

Power must be disconnected (see page 2, WARNING item 2) before inserting motor plugs into control assembly.

IN ORDER TO PREVENT MOTOR/CONTROL DAMAGE:

1

2 3

1

2

ZB80M

n

ZB110M Installation Guide

Page 12

WARNING Before servicing or cleaning unit, switch

power off at service panel and lock the service disconnecting

means to prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked, securely fasten

a prominent warning device, such as a tag, to the service panel.

Operation

It is normal for this ventilation fan to take approximately 5 seconds to

start running after it is turned on.

Modes

(For reference, wiring diagrams are on pages 5 and 10.)

Continuous ventilation:

1. Turn master wall switch on.

2. Fan operates at user-adjustable airflow rate.

Motion sensing:

1. If master wall switch is not already on, turn it on.

2. Turn sensor/control wall switch on. Some installations may not have a

separate sensor/control wall switch; where it is combined with master

wall switch.

3. Fan operates at certified airflow rate and sensor detects motion.

4. When no more motion is detected, fan enters time delay mode. (See

below.)

Manual-on (optional manual-on wall switch must be installed):

1. Turn master and manual-on wall switches on (sensor/control wall

switch can be on or off).

2. Fan operates at certified airflow rate.

3. When manual-on wall switch is turned off, fan enters timed-off mode.

(See below.)

Time Delay:

Fan continues to run at cerified airflow rate until user-adjustable TIME

delay has passed, then fan reverts to user-adjustable airflow rate.

To Set the User-Adjustable Airflow Rate*

Using a small, flat-blade screwdriver, carefully rotate the CFM

adjustment until the arrow points to the desired airflow rate.

To Set the User-Adjustable Time Delay*

Using a small, flat-blade screwdriver, carefully rotate TIME adjustment

until the arrow points to the desired minutes of time delay.

* The user-adjustable controls are located in one corner of the Fan

Housing, behind the Grille.

To Turn Fan OFF

Turn the master switch OFF.

ZB80M User-adjustable controls

ZB110M User-adjustable controls

CAUTION

IN ORDER TO PREVENT MOTOR/

CONTROL DAMAGE:

DO NOT remove motor plug to stop spinning

motor.

Power must be disconnected (see

WARNING at top left of this page) before

motor plug is removed or inserted into

control assembly.

Cleaning and Maintenance

To Clean

For quiet and efficient operation, long life and

attractive appearance, remove Grille and

vacuum interior of unit with a dusting brush

attachment.

Do not use cleaning sprays, solvents or water

on, or near, the sensor.

Motor is permanently lubricated and never

needs oiling. If motor is making excessive or

unusual noises, replace Control Assembly

and Motor.

ZB80M

n

ZB110M Installation Guide

Page 13

11

1

3

9

10

12

2

6

5

4

8

7

Service Parts

Order replacement

parts by Part No.,

not by Key No.

Key No. Part No. Description

1 97018349 Mounting Frame

2 97018721 Knockout Plate & Screws

3 97018382 Housing

4 97018472 Wiring Panel/Harness Assembly

5 97018846 Motion Control Assembly

6 1102582 Control Assembly & Motor (ZB80M)

1102583 Control Assembly & Motor (ZB110M)

7 97018331 Duct Connector

8 99111513 6” to 4” Reducer (ZB80M only)

9 99020301 Blower Wheel

10 97019371 Scroll Assembly (ZB80M)

97018768 Scroll Assembly (ZB110M)

11 97018775 Grille Assembly (includes 12)

12 99140208 Grille Spring (2 req’d)

Troubleshooting

Before continuing, turn off power as previously noted

in WARNING and CAUTION sections at the top of the

previous page.

Symptom: Fan does not run.

• Check for an open fuse or circuit breaker in building’s

service panel.

• Check two (2) plug-in connections for Motor and its

Control are seated firmly in place.

• Check two (2) plug-in connections for Sensor and its

Control are seated firmly in place.

• Check that Blower Wheel spins freely.

Symptom: Motion mode does not operate fan at certi-

fied air flow rate.

• Check two (2) plug-in connections for Sensor and its

Control are seated firmly in place.

Symptom: Fan runs erratically.

• Check that Blower Wheel is firmly attached to Motor

shaft and both spin freely.

Symptom: Fan seems noisy.

• Check that back draft damper in fan’s Duct Connector

pivots freely. Screws used to attach duct to Duct Con-

nector may prevent damper from opening.

• Check that back draft damper in wall or roof cap pivots

freely. Dampers are sometimes mistakenly painted shut

or obstructed by bird or insect debris.

Symptom: Fan does not properly ventilate room.

• For spot ventilation, turn both master switch and sensor/

control wall switch ON, so sensor/control operates fan at

certified airflow rate.

• For spot ventilation followed by continuous ventilation,

increase the “TIME” setting of user-adjustable time de-

lay.

• For continuous ventilation, increase “CFM” setting of

user-adjustable airflow rate.

ZB80M

n

ZB110M Installation Guide

Page 14

99045844B

Warranty

Broan Ventilation Fan/Lights Limited Warranty

WARRANTY PERIOD: Broan warrants to the original consumer purchaser

of its Broan Ventilation Fan/Light (the “Fan”) that your Fan (excluding lamps/

bulbs) will be materially free from defects in materials or workmanship for a

period of three (3) years from the date of original purchase. The warranty on

the lamps/bulbs provided with the Fan is one (1) year and does not cover

lamp/bulb breakage. This warranty does not cover accessories, such as

speed controls, that may be purchased separately and installed with the Fan.

The limited warranty period for replacement parts, and for Fans repaired or

replaced under this limited warranty, shall continue for the remainder of the

original warranty period.

NO OTHER WARRANTIES: THE FOREGOING WARRANTIES ARE

EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR

IMPLIED. BROAN DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS

WARRANTIES, AND DISCLAIMS AND EXCLUDES ALL WARRANTIES

IMPLIED BY LAW, INCLUDING WITHOUT LIMITATION THOSE OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TO

THE EXTENT THAT APPLICABLE LAW PROHIBITS THE EXCLUSION

OF IMPLIED WARRANTIES, THE DURATION OF ANY APPLICABLE

IMPLIED WARRANTY IS LIMITED TO THE PERIOD SPECIFIED FOR THE

EXPRESS WARRANTY. Some states do not allow limitations on how long an

implied warranty lasts, so the above limitation may not apply to you. Any oral

or written description of the Fan is for the sole purpose of identifying it and

shall not be construed as an express warranty.

REMEDY: During the applicable limited warranty period, Broan will, at its

option, provide replacement parts for, or repair or replace, without charge,

any Fan or part thereof, to the extent Broan finds it to be covered by and in

breach of this limited warranty. Broan will ship the repaired or replaced Fan

or replacement parts to you at no charge. You are responsible for all costs

for removal, reinstallation and shipping, insurance or other freight charges

incurred in the shipment of the Fan or part to Broan. This warranty does not

cover (a) normal maintenance and service, (b) normal wear and tear, (c) any

Fans or parts which have been subject to misuse, abuse, abnormal usage,

negligence, accident, improper or insufficient maintenance, storage or repair

(other than repair by Broan), (d) damage caused by faulty installation, or

installation or use contrary to recommendations or instructions, (e) any Fan

that has been moved from its original point of installation, (f) damage caused

by environmental or natural elements, (g) damage in transit, (h) natural wear

of finish, (i) Fans in commercial or nonresidential use, or (j) damage caused

by fire, flood or other act of God. This warranty covers only Fans sold in the

United States or through U.S. distributors authorized by Broan.

EXCLUSION OF DAMAGES: BROAN’S OBLIGATION TO PROVIDE

REPLACEMENT PARTS, OR REPAIR OR REPLACE, AT BROAN’S

OPTION, SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER

THIS LIMITED WARRANTY AND BROAN’S SOLE AND EXCLUSIVE

OBLIGATION. BROAN SHALL NOT BE LIABLE FOR INCIDENTAL,

INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT

OF OR IN CONNECTION WITH THE FAN, ITS USE OR PERFORMANCE.

Incidental damages include but are not limited to such damages as loss of

time and loss of use. Consequential damages include but are not limited to

the cost of repairing or replacing other property which was damaged if the

Fan does not work properly.

Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion may not apply

to you. This warranty gives you specific legal rights, and you may also have

other rights, which vary from state to state.

This warranty supersedes all prior warranties and is not transferable from the

original consumer purchaser.

BROAN SHALL NOT BE LIABLE TO YOU, OR TO ANYONE CLAIMING

UNDER YOU, FOR ANY OTHER OBLIGATIONS OR LIABILITIES,

INCLUDING, BUT NOT LIMITED TO, OBLIGATIONS OR LIABILITIES

ARISING OUT OF BREACH OF CONTRACT OR WARRANTY,

NEGLIGENCE OR OTHER TORT OR ANY THEORY OF STRICT LIABILITY,

WITH RESPECT TO THE FAN OR BROAN’S ACTS OR OMISSIONS OR

OTHERWISE.

This warranty covers only replacement or repair of defective Fans or parts

thereof at Broan’s main facility and does not include the cost of field service

travel and living expenses.

Any assistance Broan provides to or procures for you outside the terms,

limitations or exclusions of this limited warranty will not constitute a waiver

of such terms, limitations or exclusions, nor will such assistance extend or

revive the warranty.

Broan will not reimburse you for any expenses incurred by you in repairing

or replacing any defective Fan, except for those incurred with Broan’s prior

written permission.

HOW TO OBTAIN WARRANTY SERVICE: To qualify for warranty service,

you must (a) notify Broan at the address or telephone number stated below

within seven (7) days of discovering the covered defect, (b) give the model

number and part identification and (c) describe the nature of any defect in

the Fan or part. At the time of requesting warranty service, you must present

evidence of the original purchase date.

Broan, 926 West State Street, Hartford, WI 53027

(1-800-637-1453)

www.broan.com

If you must send the Fan or part to Broan, as instructed by Broan, you must

properly pack the Fan or part—Broan is not responsible for damage in transit.

ZB80M n ZB110M

X2 | Ventilador de

velocidad múltiple con

sensor de movimiento

GUÍA DE INSTALACIÓN

LEA Y CONSERVE ESTAS INSTRUCCIONES

Aviso al instalador: Deje esta guía con el dueño de la casa.

Registre su producto en línea en www.broan.com/register.

Fácil instalación en construcciones

nuevas y en aplicaciones de conversión.

Índice

Advertencias y precauciones 2

Instalación típica 2

Instalación en una construcción nueva 3

Instalación de conversión 7

Funcionamiento 12

Limpieza y mantenimiento 12

Resolución de problemas 12

Piezas de servicio 13

Garantía 14

Guía de instalación del ventilador ZB80M

n

ZB110M

Página 2

ADVERTENCIA

PARA REDUCIR EL RIESGO DE INCENDIOS, DESCARGAS

ELÉCTRICAS O LESIONES PERSONALES, OBSERVE LAS SIGUIENTES

PRECAUCIONES:

1. Use la unidad solo de la manera indicada por el fabricante. Si tiene

preguntas, comuníquese con el fabricante a la dirección o al número

telefónico que se incluye en la garantía.

2. Antes de dar servicio a la unidad o de limpiarla, interrumpa el suministro

eléctrico en el panel de servicio y bloquee los medios de desconexión

del servicio para evitar que la electricidad se reanude accidentalmente.

Cuando no sea posible bloquear los medios de desconexión del

servicio, fije firmemente una señal de advertencia (como una etiqueta)

en un lugar visible del panel de servicio.

3. El trabajo de instalación y el cableado eléctrico deben estar a cargo de

un personal capacitado, de acuerdo con todos los códigos y normas

correspondientes, incluidos los códigos y normas de construcción

específicos sobre protección contra incendios.

4. Es necesario que haya suficiente aire para que se lleve a cabo una

combustión y una extracción adecuadas de los gases a través del tubo

de humos (chimenea) del equipo quemador de combustible, con el fin

de evitar el contratiro. Siga las directrices y las normas de seguridad

del fabricante del equipo de calefacción, como las publicadas por la

Asociación Nacional de Protección contra Incendios (National Fire

Protection Association, NFPA), la Sociedad Americana de Ingenieros

de Calefacción, Refrigeración y Aire Acondicionado (American Society

for Heating, Refrigeration and Air Conditioning Engineers, ASHRAE) y

las autoridades de los códigos locales.

5. Al cortar o perforar a través de la pared o del cielo raso, tenga cuidado

de no dañar el cableado eléctrico ni otros servicios ocultos.

6. Los ventiladores con conductos siempre se deben conectar hacia

elexterior.

7. Use solamente un interruptor de ENCENDIDO/APAGADO, un

temporizador mecánico o un control de relé-interruptor.

8. Esta unidad puede instalarse sobre una tina o ducha siempre que se

conecte a un GFCI (interruptor accionado por pérdida de conexión a

tierra) en un circuito de derivación protegido.

9. Esta unidad debe estar conectada a tierra.

Instalación típica

PRECAUCIÓN

1. Solo para usarse como medio de ventilación general. No debe usarse

para la extracción de materiales o vapores peligrosos o explosivos.

2. Este producto está diseñado para instalarse solamente en un cielo

raso plano. El sensor no funcionará de forma fiable si el producto no

se instala en un cielo raso plano. NO MONTE ESTE PRODUCTO EN

LA PARED.

3. Para evitar daños a los cojinetes del motor y rotores ruidosos o

desbalanceados, mantenga la unidad de potencia protegida contra

rociados de yeso, polvos de construcción, etc.

4. Lea la etiqueta de especificaciones del producto para ver información

y requisitos adicionales.

45° 45°

• La instalación es la misma para:

• Cabe en una construcción de cielo raso de

2 x 8 pulg. (5.1 x 20.3 cm)

• Ajustes ilimitados de la posición del

ventilador entre las vigas de 14 a 24 pulg.

(35.6 a 61 cm) en el centro.

*Se compra por

separado.

AISLAMIENTO*

(Colóquelo alrededor y

sobre la cubierta del

ventilador).

TAPA DE

TECHO *

(con regulador

de tiro integrado)

CUBIERTA DEL

VENTILADOR

CABLE

ELÉCTRICO*

CONDUCTO

REDONDO*

CODOS

REDONDOS*

Selle las

separaciones

alrededor de

la cubierta.

Selle con

cinta

las uniones

de los

conductos.

O

Mantenga

cortos

los tramos

de conductos.

TAPA DE

PARED *

(con regulador

de tiro integrado)

NO USAR EL PRODUCTO EN UN ÁREA DE COCINA

No instale el equipo sobre o dentro de esta área

Piso

Equipo

de cocina

Vigas Vigas en “I” Cerchas

Los conductos desde este ventilador hacia el exterior del edificio tienen un gran efecto sobre el flujo de aire, el ruido y el uso de energía

del ventilador. Utilice el tramo de conductos más corto y recto posible para obtener un desempeño óptimo y evite instalar el ventilador

con conductos menores que los recomendados. El aislamiento alrededor de los conductos puede reducir la pérdida de energía e inhibir

el desarrollo de moho. Los ventiladores instalados en conductos existentes podrían no obtener el flujo de aire nominal.

Para un mejor desempeño, se recomienda utilizar conductos metálicos redondos y rígidos de 6 pulg. (15.2 cm).

Guía de instalación del ventilador ZB80M

n

ZB110M

Página 3

1

2

3

4

Instalación en una construcción nueva

Herramientas necesarias

• Destornillador eléctrico con cabeza Phillips

• Destornillador Phillips

• Destornillador de cabeza plana

• Alicates

• Desforrador de cables

• Cortador de cables

Materiales necesarios

• Se recomienda utilizar conductos metálicos redondos de 6 pulg. (15.2 cm) para

obtener un desempeño óptimo.

Aunque el uso de otros sistemas de conductos es aceptable, puede afectar

aldesempeño.

• Tapa de techo o tapa de pared (se recomienda que tenga regulador de tiro integrado)

• Cinta para sellar las conexiones de los conductos

• Cableado eléctrico y suministros según los requisitos de los códigos locales

1

Saque el producto de su empaque

2

Instale

el marco

de montaje

La bolsa de piezas

contiene la placa

de agujero ciego y

seis (6) tornillos

Saque la hoja

de instrucciones

Retire la cubierta protectora del

empaque. Proceda con el paso 6.

Guía de instalación del ventilador ZB80M

n

ZB110M

Página 4

3

1

4

2

1

2

3

Instalación en una construcción nueva

3

Acople y fije

la cubierta

4

Acople el conector de conducto y los conductos

Coloque la cubierta entre

las vigas y doble el canal

a ambos lados del marco

de montaje para fijar

la cubierta en su lugar.

No doble la cubierta.

Tornillos de la bolsa de piezas

Las bridas superior e inferior se

instalan por fuera de la cubierta

Introduzca la pestaña en

la ranura del interior de

la cubierta

Tornillo de

la bolsa

de piezas

Reductor de 6 a 4 pulg (15.2 a 10.2 cm) (para modelo ZB80M solamente)

Cinta

Conductos de

6 pulg. (15.2 cm)

Conductos de

4 pulg. (10.2 cm)

Acople

a presión

Guía de instalación del ventilador ZB80M

n

ZB110M

Página 5

3

4

1

2

Instalación en una construcción nueva

5

Conecte los cables e instale la placa de agujero ciego

• Tienda el cable eléctrico de 120 VCA hasta el lugar de la instalación.

• Use conectores aprobados por UL para fijar el cableado a la placa de agujero ciego incluida en la bolsa de piezas.

• Conecte los cables tal como se ilustra en el diagrama de cableado.

Tornillo de

la bolsa

de piezas

Acople la abrazadera para

cables a la placa de agujero

ciego. La placa de agujero ciego

se monta en el exterior de la

cubierta y puede orientarse en la

dirección que se desee.

Conecte los cables

SENSOR/

CONTROL

NEGRO

BLANCO

NEGRO

NARANJA

CAFÉ

ENCENDIDO

MANUAL

TIERRA

BLANCO

NEGRO

TIERRA

BLANCO

NEGRO

AZUL

120 VCA

LÍNEA DE

ENTRADA

INTERRUPTORES DE PARED

MULTIFUNCIONALES O ESTÁNDAR

ROJO

14/4

(SI SE UTILIZAN

TODAS

LAS OPCIONES DE

INTERRUPTORES

DE PARED)

SENSOR/

CONTROL

ROJO

INTERRUPTOR

MAESTRO

VENTILADOR

INTERRUPTOR

MAESTRO DE

ENCENDIDO/

APAGADO*

INTERRUPTOR

DE ENCENDIDO

MANUAL*

PLACA DE

AGUJERO CIEGO

RECEPTÁCULOS

LÍNEA DE ENTRADA

DE 120 VCA

CAJA DEL INTERRUPTOR

NEGRO

BLANCO

ROJO

AZUL

* Se compra por separado

INTERRUPTOR

DE CONTROL/

SENSOR*

TIERRA

(Verde o sin aislamiento)

NARANJA

CAFÉ

• Vea los detalles

de la sección

FUNCIONAMIENTO

en la página 26.

• El interruptor

MAESTRO enciende

y apaga el sistema

del ventilador para

fines de limpieza y

mantenimiento.

• El interruptor del

SENSOR/CONTROL

enciende/apaga

el funcionamiento

automático del control

de movimiento.

• El interruptor de ENCENDIDO

MANUAL aumenta directamente el

funcionamiento del ventilador a un

índice certificado de flujo de aire.

• Se pueden combinar los interruptores

MAESTRO y SENSOR/CONTROL

(vea la página 24).

• El interruptor MAESTRO, junto o por

separado del interruptor SENSOR/

CONTROL, se puede colocar donde

no se pueda tener acceso fácilmente

para uso diario; tal vez sea necesario

etiquetarlo y situarlo donde no se

pueda encender sin ser visto desde

el ventilador para cumplir con los

códigos locales y nacionales.

Guía de instalación del ventilador ZB80M

n

ZB110M

Página 6

1

3

2

Instalación en una construcción nueva

6

Inserte la cubierta

` protectora y

finalice el cielo

raso

7

Instale la rejilla

Consulte la página 12 para obtener información sobre el funcionamiento, limpieza, mantenimiento y resolución de problemas.

La cubierta protege

la unidad durante la

construcción. Retírela

antes de instalar

la rejilla.

• Instale el material del

cielo raso.

• Recorte alrededor de

la cubierta.

Conecte

el sensor

PRECAUCIÓN

Si el motor estaba desconectado, se debe desconectar la

electricidad (vea la página 16, ADVERTENCIA, punto 2) antes

de insertar los enchufes del motor en el conjunto de control.

PARA PREVENIR DAÑOS EN

EL MOTOR/CONTROL:

La page charge ...

Broan ZB110M Guide d'installation

Ce manuel convient également à

Broan ZB110M Guide d'installation

dans d''autres langues

Documents connexes

Autres documents