Sony DR-BT10CX Mode d'emploi

Wireless Stereo

Headset

2-698-598-51(1)

DR-BT10CX

Operating Instructions

Mode d’emploi

FR

US

2

US

WARNING

To reduce the risk of fire or electric

shock, do not expose this

apparatus to rain or moisture.

To reduce the risk of electrical

shock, do not open the cabinet.

Refer servicing to qualified

personnel only.

Do not install the appliance in a

confined space, such as a bookcase or

built-in cabinet.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with

newspapers, tablecloths, curtains, etc.

And do not place lighted candles on the

apparatus.

To reduce the risk of fire or electric

shock, do not place objects filled with

liquids, such as vases, on the apparatus.

Connect the AC power adaptor to an

easily accessible AC outlet. Should you

notice an abnormality in the AC power

adaptor, disconnect it from the AC outlet

immediately.

Information

This device complies with Part 15 of FCC

Rules and RSS-Gen of IC Rules.

Operation is subject to the following two

conditions: (1) this device may not cause

interference, and (2) this device must

accept any interference, including

interference that may cause undesired

operation of this device.

You are cautioned that any changes or

modifications not expressly approved in

this manual could void your authority to

operate this equipment.

This equipment must not be co-located or

operated in conjunction with any other

antenna or transmitter.

This equipment complies with FCC/IC

radiation exposure limits set forth for

uncontrolled equipment and meets the

FCC radio frequency (RF) Exposure

Guidelines in Supplement C to OET65

and RSS-102 of the IC radio frequency

(RF) Exposure rules. This equipment has

very low levels of RF energy that it is

deemed to comply without testing of

specific absorption ratio (SAR).

The Bluetooth word mark and logos are

owned by the Bluetooth SIG, Inc. and any

use of such marks by Sony Corporation is

under license.

Other trademarks and trade names are

those of their respective owners.

MPEG Layer-3 audio coding technology

and patents licensed from Fraunhofer IIS

and Thomson.

3

US

Table Of Contents

Welcome! .......................... 4

3 steps to BLUETOOTH

function ................................. 5

Location and Function of

Parts............................... 6

Charging the unit ............. 7

Pairing ............................... 9

What is pairing? ........................ 9

Procedures of pairing ................ 9

Wearing the headset ...... 11

Indications of

BLUETOOTH function

.. 12

Listening to music ......... 13

Calling ............................. 15

Controlling the BLUETOOTH

mobile phone – HFP, HSP .. 17

Calling while playing

back music .................. 18

Disposing of the unit ..... 19

Precautions .................... 20

What is BLUETOOTH

technology? ................ 22

Troubleshooting ............. 23

Initializing the unit ......... 24

Specifications ................. 25

For the customers in the USA

and Canada

RECYCLING LITHIUM-ION

BATTERIES

Lithium-Ion

batteries are

recyclable.

You can help

preserve our

environment by

returning your used

rechargeable

batteries to the

collection and

recycling location

nearest you.

For more information regarding

recycling of rechargeable

batteries, call toll free 1-800-822-

8837, or visit

http://www.rbrc.org/

Caution: Do not handle damaged

or leaking Lithium-Ion batteries.

4

US

Welcome!

Thank you for purchasing this Sony Wireless Stereo Headset. This unit uses

BLUETOOTH

TM

wireless technology.

• You can enjoy music from your BLUETOOTH device capable of

transmitting music.

• You can enjoy hands-free talking with your BLUETOOTH mobile phone

inside your bag.

• You can charge the unit using the supplied battery charging stand.

For details on BLUETOOTH technology, see page 22.

Enjoy listening to music

Talking on the phone

5

US

V

Calling

V

Listening to music

VV

3 steps to BLUETOOTH function

BLUETOOTH

mobile phone,

etc.

Pairing

Wireless Stereo

Headset

BLUETOOTH connection

Operate the BLUETOOTH

device to make BLUETOOTH

connection.

Connection

Listening to music

You can listen to music played on

the BLUETOOTH device.

Music

BLUETOOTH connection

When the unit is turned on, the unit

starts making the BLUETOOTH

connection to the recognized

mobile phone automatically.

Talking on the phone

You can make and receive a call

by operating unit.

Pairing (each device)

First, register (“pair”) a BLUETOOTH device (mobile phone, etc.) and

this unit with each other. Once pairing is established, there is no need for

pairing again.

Voice

Connection

A2DP HFP HSP

c Page 9

c Page 13 c Page 15

c Page 16 - 17c Page 13 - 14

6

US

Location and Function of Parts

1 Multi function button

Controls various call

functions.

2 Indicator (red)

Indicates the power status of

the unit.

3 Indicator (blue)

Indicates the communication

status of the unit.

4 POWER button

5 Earpieces

6 VOL – button

7 VOL + button

8 Microphone

9 RESET button

0 Holding clip

Adjust the holding clip to the

desired angle and clip to your

pocket or collar.

qa Contact point

GETTING STARTED

7

US

1 Connect the supplied

AC power adaptor with

the battery charging

stand.

2 Connect the supplied

AC power adaptor to an

AC outlet.

Charging the unit

The unit contains a rechargeable Lithium-Ion battery, which should be

charged before using for the first time.

3 Put the unit on the

battery charging stand.

Note

If the holding clip is turned, the

unit cannot be set on the battery

charging stand and charging does

not start. Turn the holding clip

back to the original position before

charging.

Rest the unit on the battery

charging stand so that the unit’s

contact point meets the contact pin

on the battery charging stand, and

make sure that the indicator (red)

lights up.

Charging is completed in about 3

hours* and the indicator (red) goes

off automatically.

* Time required for empty battery to

recharge.

Tip

When charging the battery, the unit is

turned off automatically.

Continued

Battery charging

stand (supplied)

(Rear)

AC power

adaptor

(supplied)

To an AC

outlet

Battery charging

stand (supplied)

Wireless Stereo

Headset

Contact pin

8

US

Approx.

usage hours

11 hours

100 hours

Caution

If this unit detects a problem while

charging, the indicator (red) may

turn off, although charging is not

complete.

Check for the following causes:

– Ambient temperature exceeds the range

of 0 °C – 40 °C (32 °F – 104 °F).

– There is a problem with the battery.

In this case, charge again within the

above-mentioned temperature range.

If the problem persists, consult your

nearest Sony dealer.

Notes

• If the battery is not used for a long time,

battery may be quickly depleted,

however, after a few recharges, battery

life will improve.

• If the life of the built-in rechargeable

battery drops to half the normal length,

the battery should be replaced. Consult

your nearest Sony dealer for

replacement of the rechargeable battery.

• Avoid exposure to temperature

extremes, direct sunlight, moisture,

sand, dust or mechanical shock. Never

leave in a car parked in the sun.

• Use only the supplied AC power

adaptor. Do not use any other AC

power adaptor.

Status

Full

Mid

Low

(needs to

charge)

Usage hours

*

Status

Communication

time (including

music playback

time) (up to)

Standby time

(up to)

* Time stated above may vary, depending

on ambient temperature or conditions of

use.

Checking the remaining

battery

When pressing the POWER button

while the unit is turned on, the

indicator (red) flashes. You can

check the remaining battery by the

number of times the indicator (red)

flashes.

Indicator (red)

3 times

2 times

1 time

Note

You cannot check the remaining battery

immediately after the unit is turned on, or

while pairing.

When the battery is almost empty

The indicator (red) flashes slowly

automatically.

When the battery becomes empty, a beep

sounds and the unit will turn off

automatically.

9

US

Pairing

Continued

What is pairing?

BLUETOOTH devices need to be

“paired” with each other

beforehand.

Once BLUETOOTH devices are

paired, there is no need for pairing

again, except in the following cases:

• When pairing information is

deleted after repair, etc.

• When this unit is paired with 9 or

more devices.

This unit can be paired with 8

BLUETOOTH devices; if a new

device is paired after 8 devices

have been paired, the device

whose latest connection time is

the oldest among the 8 paired

devices is replaced by the new

one.

• When recognition of the unit by

the device to be connected is

deleted.

• When this unit is initialized.

All pairing information is deleted.

Procedures of pairing

1 Place the connecting

device within 1 m (3 ft)

of this unit.

2 Press and hold the

POWER button for 7

seconds or more to

standby for pairing

while the unit is turned

off.

Notes

• After about 3 seconds, power is

turned on and the indicator

(blue) and indicator (red) flash

together twice. Keep the button

pressed without releasing until

both indicators start flashing

together, then release the button.

This unit enters into pairing

mode.

•

If pairing is not established

within about 5 minutes, pairing

mode will be canceled and this

unit will turn off. In this case,

start over from step 1.

10

US

3 Perform pairing

procedure on the

connecting device to

detect this unit.

The list of detected devices

appears on the display of the

connecting device. This unit is

displayed as “DR-BT10CX.”

Note

If “DR-BT10CX” is not displayed,

repeat from step 1.

4 Select “DR-BT10CX” on

the display of the

connecting device.

5 If Passcode* input is

required on the display

of a connecting device,

input “0000.”

Pairing is complete when the

indicator (blue) flashes slowly.

The message standing for

“Pairing complete” appears on

the display of some

BLUETOOTH devices.

* Passcode may be called

“Passkey,” “PIN code,” “PIN

number,” or “Password.”

Note

Passcode of this unit is fixed at

“0000.” This unit cannot be paired

with a BLUETOOTH device

whose Passcode is not “0000.”

6 Start the BLUETOOTH

connection from the

BLUETOOTH device.

This unit memorizes the

device as the latest connected

device. Some BLUETOOTH

devices may connect with the

unit automatically when

pairing is complete.

When pairing with a

BLUETOOTH device that

cannot display a list of

detected devices or that

has no display

You may pair the device by setting

both this unit and the connecting

device to pairing mode. For details,

refer to the operating instructions

supplied with the connecting device.

Tips

• To pair with other BLUETOOTH

devices, repeat steps 1 to 5 for each

device.

• To delete all pairing information, see

“Initializing the unit” (page 24).

11

US

How to install the earbuds

correctly

If the earbuds do not fit your ears

correctly, low-bass sound may not

be heard. To enjoy better sound

quality, adjust the earbuds position

to sit on your ears comfortably or

push them into the inside of your

ears so that they fit your ears snugly.

If the earbuds do not fit your ears,

try ones of other size.

How to use the holder

Store the earpieces. It prevents the

cord from tangling if you store the

earbuds.

Wear the earpiece marked R in

your right ear and the one marked

L in your left ear.

1 Turn the holding clip to the

desired angle and clip to your

pocket or collar.

Wearing the headset

LR

1

12

US

Indications of BLUETOOTH function

B : Indicator (blue)

R : Indicator (red)

Status Flashing patterns

Searching

B

– – – – – – – –

...

R

– – – – – – – –

...

Connectable

B

– – – – – – – – – –

...

R

–

Connecting

B

– – – – – – – – – –

...

R

– – – – – – – – – –

...

HFP/HSP or A2DP

B

– – – – – – – – – – – – – –

...

(standby for receiving audio signal)

R

–

HFP/HSP and A2DP

B

– – – – – – – – – – – –

...

(standby for receiving audio signal)

R

–

Listening

B

– – – – – – – – – – – –

...

R

–

Listening during standby

B

– – – – – – – – – –

...

for telephone call

R

–

Incoming call

B

...

R

–

Talking

B

– – – – – – – – – – – –

...

R

–

Calling while

B

– – – – – – – – – –

...

playing back music

R

–

Pairing

Connecting

Connected

Phone

Music

13

US

Check the following before

operating the unit.

– The BLUETOOTH device is

turned on.

–

Pairing of this unit and the

BLUETOOTH device is complete.

– The BLUETOOTH device

supports the transmitting music

function (profile: A2DP).

1 Press and hold the

POWER button for

about 3 seconds while

the unit is turned off.

The indicator (blue) and

indicator (red) flash together

twice and the unit is turned on.

Note

Do not press and hold the POWER

button for more than 7 seconds,

otherwise pairing mode is entered.

2 Make the BLUETOOTH

connection (A2DP) from

a BLUETOOTH device to

this unit.

Refer to the operating

instructions supplied with the

BLUETOOTH device on how

to operate it.

Listening to music

3 Start playback on the

BLUETOOTH device.

Notes

• When you play music by connecting the

unit to a BLUETOOTH device using

HSP (Headset Profile)*, sound quality

will not be high. For better sound,

change the BLUETOOTH connection

to A2DP (Advanced Audio Distribution

Profile)* by operating the

BLUETOOTH device.

• This unit cannot control music playback

functions of the connected device.

* For detail on profiles, see page 22.

To adjust the volume

Press the VOL + or – button while

listening to the music.

Tips

• When the volume level is low, raise the

volume of the connected device. The

sound will be clearer.

• Volume level for listening to music and

calling can be set independently.

Note

You cannot adjust the volume of the

BLUETOOTH device by the unit VOL

buttons.

OPERATING THE UNIT

Continued

POWER button

VOL + button

VOL –

button

14

US

To stop use

1 Terminate the

BLUETOOTH

connection by operating

the BLUETOOTH device.

2 Press and hold the

POWER button for

about 3 seconds.

The indicator (blue) and

indicator (red) light up

together, and the unit turns

off.

Tip

When you finish playing music, the

BLUETOOTH connection may terminate

automatically, depending on the

BLUETOOTH device.

15

US

When you want to connect the unit

to a different BLUETOOTH mobile

phone from the last time, follow the

procedure in “When this unit does

not connect to a BLUETOOTH

mobile phone automatically.”

When this unit does not

connect to a BLUETOOTH

mobile phone automatically

1 Make the BLUETOOTH

connection (HFP or

HSP) from the

BLUETOOTH mobile

phone to this unit.

Refer to the manual supplied

with your BLUETOOTH

mobile phone for operation

details.

The list of recognized devices

appears on the display of the

BLUETOOTH mobile phone.

This unit is displayed as

“DR-BT10CX.”

When you use the

BLUETOOTH mobile phone

features both HFP (Hands-free

Profile) and HSP (Headset

Profile)*, set to HFP.

* For details on profiles, see page 22.

Note

When listening to music by operating this

unit connected to a BLUETOOTH mobile

phone, make the BLUETOOTH

connection by operating the

BLUETOOTH mobile phone. This cannot

be done with the multi function button.

Check the following before

operating the unit.

– The BLUETOOTH function is

active on the mobile phone.

– Pairing of this unit and the

BLUETOOTH mobile phone is

complete.

1 Press and hold the

POWER button for

about 3 seconds while

the unit is turned off.

The indicator (blue) and

indicator (red) flash together

twice, the unit turns on and

then this unit automatically

connects to the last

BLUETOOTH mobile phone

that was used.

Note

Do not press and hold the POWER

button for more than 7 seconds,

otherwise pairing mode is entered.

Tip

This unit will stop trying to connect to the

BLUETOOTH mobile phone after 1

minute. In such a case, press the multi

function button to try to connect again.

Calling

Continued

Multi function

button

POWER button

VOL + button

VOL –

button

16

US

To call

1 Use the buttons on your

mobile phone when

making a call.

If no sound is heard through

this unit, press the multi

function button.

Tip

You can call in the following way,

depending on the BLUETOOTH mobile

phone. Refer to the manual supplied with

your mobile phone on operating details.

– When not communicating, you can call

using the voice-dial function by

pressing the multi function button.

– You can call a specific number by

pressing the multi function button for

about 2 seconds.

To receive a call

When the telephone is ringing, ring

tone will be heard through the unit.

1 Press the multi function

button on the unit.

The ring tone differs in the

following ways, depending on

your mobile phone.

– ring tone set on the unit

– ring tone set on the mobile

phone

– ring tone set on the mobile

phone only for BLUETOOTH

connection

Note

If you pressed the call button on the

BLUETOOTH mobile phone, some

BLUETOOTH mobile phones may have

handset use priority. In this case, set to

talk with the unit by pressing and holding

the multi function button for about 2

seconds, or by operating the

BLUETOOTH mobile phone. For details,

refer to the manual supplied with your

BLUETOOTH mobile phone.

To adjust the volume

Press the VOL + or – button.

Tips

• You cannot adjust the volume when not

communicating.

• Volume level for calling and listening

to music can be set independently.

To terminate a call

You can end a call by pressing the

multi function button on the unit.

To stop use

1 Terminate BLUETOOTH

connection by the

BLUETOOTH mobile

phone.

2 Press and hold the

POWER button for

about 3 seconds to turn

off the power.

The indicator (blue) and

indicator (red) light up

together, and the unit turns

off.

17

US

*

1

Some functions may not be supported

depending on the BLUETOOTH

mobile phone.

*

2

This may vary, depending on the

BLUETOOTH mobile phone.

*

3

Some functions may not be supported

when calling using the BLUETOOTH

mobile phone.

Status Multi function button

Standby

Voice Dial

active

Outgoing call

Incoming call

During call

Short Press

Start Voice

Dial

Cancel Voice

Dial

End outgoing

call

Answer

End call

Long Press

Last number

redial

–

Reject

Change active

device

Status Multi function button

Standby

Outgoing call

Incoming call

During call

Short Press

–

End outgoing

call

*

1

Answer

End call

*

3

Long Press

Dial

*

1

End outgoing

call or change

active device to

headset*

2

–

Change active

device to

headset

Controlling the

BLUETOOTH mobile

phone – HFP, HSP

The operation of the buttons on this

unit varies depending on your

mobile phone.

HFP (Hands-free Profile) or HSP

(Headset Profile) is used for

BLUETOOTH mobile phone. Refer

to the operating instructions

supplied with your BLUETOOTH

mobile phone on supported

BLUETOOTH profiles or how to

operate.

HFP (Hands-free Profile)

HSP (Headset Profile)

18

US

Calling while playing back music

If the BLUETOOTH connection is active with the mobile phone, you can

switch the unit to call even when listening to music.

Before starting, see “Calling” (page 15) on operating details.

To call while playing back

music

1 Press the multi function

button while playing

back music (page 15), or

operate your

BLUETOOTH mobile

phone to make a

telephone call.

If no sound is heard through

this unit, press and hold the

multi function button for about

2 seconds.

To receive a call while

playing back music

The sound through the unit changes

to a ring tone automatically.

1 Press the multi function

button and talk.

After finishing the call, press

the multi function button. This

unit is switched back to music

playback.

If the sound does not

change to a ring tone

automatically

1 Stop music playback.

2 When ringing, press the

multi function button

and talk.

19

US

Disposing of the unit

For environmental conservation, be sure to remove the built-in rechargeable

battery from the unit before disposing, and dispose of the battery

appropriately.

ADDITIONAL INFORMATION

1 Remove 2 screws.

2 Open the case and

detach the connector.

Rechargeable

battery

3 Remove the

rechargeable battery

and dispose of it.

20

US

Precautions

On BLUETOOTH communication

• BLUETOOTH wireless technology

operates within a range of about 10 m

(about 30 ft).

Maximum communication range may

vary depending on obstacles (person,

metal, wall, etc.) or electromagnetic

environment.

• The antenna of this unit is built into the

unit. The sensitivity of BLUETOOTH

communication will improve by placing

a connected BLUETOOTH device near

the unit.

• The following conditions may affect the

sensitivity of BLUETOOTH

communication.

– There is an obstacle such as a person,

metal, or wall between this unit and

BLUETOOTH device.

–A device using 2.4 GHz frequency,

such as a wireless LAN device,

cordless telephone, or microwave

oven, is in use near this unit.

• Because BLUETOOTH devices and

wireless LAN (IEEE802.11b/g) use the

same frequency, microwave

interference may occur and resulting in

communication speed deterioration,

noise, or invalid connection if this unit

is used near a wireless LAN device. In

such as case, perform the following.

– Use this unit at least 10 m (about 30

ft) away from the wireless LAN

device.

– If this unit is used within 10 m (about

30 ft) of a wireless LAN device, turn

off the wireless LAN device.

– Install this unit and BLUETOOTH

device as near to each other as

possible.

• Microwaves emitting from a

BLUETOOTH device may affect the

operation of electronic medical devices.

Turn off this unit and other

BLUETOOTH devices in the

following locations, as it may cause

an accident.

– where inflammable gas is present,

in a hospital, train, airplane, or a

petrol station

– near automatic doors or a fire alarm

• This unit supports security

capabilities that comply with the

BLUETOOTH standard to provide a

secure connection when the

BLUETOOTH wireless technology is

used, but security may not be enough

depending on the setting. Be careful

when communicating using

BLUETOOTH wireless technology.

• We do not take any responsibility for

the leakage of information during

BLUETOOTH communication.

• Connection with all BLUETOOTH

devices cannot be guaranteed.

–A device featuring BLUETOOTH

function is required to conform to

the BLUETOOTH standard

specified by BLUETOOTH SIG,

and be authenticated.

– Even if the connected device

conforms to the above mentioned

BLUETOOTH standard, some

devices may not be connected or

work correctly, depending on the

features or specifications of the

device.

– While talking on the phone hands

free, noise may occur, depending

on the device or communication

environment.

• Depending on the device to be

connected, it may require some time

to start communication.

La page charge ...

Sony DR-BT10CX Mode d'emploi

Sony DR-BT10CX Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents