Firman P01001 Mode d'emploi

P/N:310745460 Rev:03

OWNER’S MANUAL

Read all safety precautions and instructions carefully

before operating equipment.

Ensure engine is stopped and level before performing

any maintenance or service.

IMPORTANT:

Record product information to reference when ordering parts or

obtaining warranty coverage.

Serial Number:

PORTABLE GENERATOR

MODEL NUMBER

P01001

Rev Level:02

DO NOT RETURN TO

STORE!

CALL US FIRST!

CUSTOMER HOTLINE

1-844-347-6261

FOR QUESTIONS OR SERVICE

INFORMATION

Purchase Date:

Table of Contents

. . . . . . . . . . . . . . . . . . . . . . . . . . .1

Safety Precautions . . . . . . . . . . . . . . . . . . . . .2

Unpacking the Generator. . . . . . . . . . . . . . . .6

Parts Included. . . . . . . . . . . . . . . . . . . . . . . .6

Install the Handle . . . . . . . . . . . . . . . . . . . . . 7

Controls and Features. . . . . . . . . . . . . . . . . 8

Generator. . . . . . . . . . . . .. . . . . . . . . . . . . .8

Control Panel. . . . . . . . . . . . . . . . . . . . . . . 9

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . 10

Add Engine Oil . . . . . . .. . . . . . . . . . . . . . . .11

Low Oil Shutdown . . . . . . . . . . . . . . . . . . . .11

Add Fuel . . . . . . .. . . . . . . . . . . . . . . . . . . . .12

Operation at High Altitude . . . . . . . . . . .12

Grounding. . . . .. . . . . . . . . . . . . . . .. . . . . .13

System.. . . . . . . . . . . . . . . . . . . . . . .. . . . . .13

Operation . . . . . . . . . . . . . . . . . . . . . . . . .. . . . 14

Generator Location . . . . . . . . . . . . . . . . . . 14

Surge Protection . . . . . . . . . . . . .. . . . . . . .14

Starting the Generator. . . . . . . . . .. . . . . . 15

Connecting Electrical Loads . . . . . . . .. . . 16

12V DC Outlet(Battery Charger) . . . . . . . 16

Stopping the Engine . . . . . . . . . . . . . . . . . 17

Low Oil Shutdown . . . . . . . . . . . . . . . . . . 18

Do Not Overload Generator . . . . . . . . . . . 18

Maintenance And Storage. . . . . . . . . . . . . . 19

Maintenance Schedule . . . . . . . . . . . . . 19

Engine Maintenance .. . . . . . . . . . . .. . . . 20

Change Engine Oil . . .. . . . . . . . . . . . . . 20

Air Filter Maintenance. . . . . . . . . . . . . .20

Spark Plug Maintenance. . . . . . . . . . . . 21

Cleaning Fuel Strainer . . . . . . . . . . . . 21

. . . 21

Generator Maintenance . . . . . . . . . . . . . . 22

Service and Storage . . . . . . . . . . . . . . . . . 23

Introduction

Inspect Muffler and Spark Arrester

. . . . . . . . . . . . . . . . . . . . .24

Parts Diagram and Parts List . . . . . . . . . . 25

Generator Parts Diagram . . . . . . . . . . . . 25

Engine Parts Diagram . . . . . . . . . .. . . . . 26

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . 27

Service Information . . . . . . . . . . . . . .. . . . . 29

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Trouble Shooting

Connecting to a Building’s Electrical

English Customer Service: 1-844-FIRMAN1

Thank you for purchasing a FIRMAN generator.

Important Safety Information

The manufacturer cannot possibly anticipate every possible circumstance that might involve a

hazard. The warnings in this manual and the tags and decals affixed to the unit are therefore not

all-inclusive. If you use a procedure, work method or operating technique that the manufacturer

does not specifically recommend you must satisfy yourself that it is safe for you and others. You

must also make sure that the procedure work method or operating technique that you choose

does not render the generator unsafe.

DANGER WARNING CAUTION

DANGER indicates a

potentially hazardous

situation which, if not

avoided. WILL result in

death or serious injury.

WARNING indicates a

potentially hazardous

situation which, if not

avoided, could result in

death or serious injury.

CAUTION indicates a

potentially hazardous

situation which, if not

avoided, may result in minor

or moderate personal injury,

or property damage.

Toxic Fumes

Fire Hazard

Hot Surface.

Do Not Touch the Surface.

Kickback

Risk of Electric Shock

Explosion Hazard

Rotating Parts Entanglement

Hazard

Operator’s Manual

INTRODUCTION

English Customer Service: 1-844-FIRMAN1

01

SAFETY PRECAUTIONS

Page 02

WARNING

POISONOUS GAS HAZARD.

•

English Customer Service: 1-844-FIRMAN1

CORRECT USAGE

Example location to reduce risk of carbon monoxide poisoning

•

ONLY use outside and downwind, far away from windows, doors and vents.

•

Direct exhaust away from occupied spaces.

INCORRECT USAGE

Do not operate in any of the following locations:

Near any door, window or vent

Garage

Basement

Crawl Space

Living Area

Attic

Entry Way

Porch

Mudroom

English Customer Service: 1-844-FIRMAN1

03

WHEN OPERATING EQUIPMENT

•

DO NOT tip engine or equipment at angle

which causes fuel to spill.

DO NOT stop engine by moving choke

control to “Start” position.

•

WHEN TRANSPORTING, MOVING

OR REPAIRING EQUIPMENT

Transport/move/repair with fuel tank

EMPTY or with fuel shutoff valve OFF.

•

DO NOT tip engine or equipment at angle

which causes fuel to spill.

Disconnect spark plug wire.

•

WHEN STORING FUEL OR EQUIPMENT

WITH FUEL IN TANK

•

WARNING

•

WARNING

Generator voltage could cause

electrical shock or burn resulting

in death or serious injury.

•

WARNING

•

NEVER start or stop engine with electrical

devices plugged in and turned on.

WARNING

Fuel and its vapors are extremely flammable

and explosive which could cause burns, fire,

or explosion resulting in death or serious

injury and/or property damage.

WHEN ADDING OR DRAINING FUEL

Turn generator engine OFF and let it cool at

least 2 minutes before removing fuel cap.

Loosen cap slowly to relieve pressure in tank.

Fill or drain fuel tank outdoors.

•

DO NOT overfill tank. Allow space for fuel

expansion.

If fuel spills, wait until it evaporates before

starting engine.

•

Keep fuel away from sparks, open flames,

pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap, and fittings

frequently for cracks or leaks. Replace if

necessary.

DO NOT light a cigarette or smoke.

•

WHEN STARTING EQUIPMENT

Ensure spark plug, muffler, fuel cap, and air

cleaner are in place.

•

DO NOT crank engine with spark plug

removed.

•

Use approved transfer equipment, suitable

for the intended use, to prevent backfeed by

isolating generator from electric utility

workers.

English Customer Service: 1-844-FIRMAN1

04

WARNING

Unintentional sparking

could cause fire or

electric shock resulting

in death or serious

injury.

WHEN ADJUSTING OR MAKING REPAIRS TO

YOUR GENERATOR

Disconnect the spark plug wire from the

spark plug and place the wire where it cannot

contact spark plug.

•

WHEN TESTING FOR ENGINE SPARK

Use approved spark plug tester.

•

DO NOT check for spark with spark plug

removed.

•

WARNING

NEVER operate generator without protective

housing or covers.

DO NOT wear loose clothing, jewelry or

anything that could be caught in the starter

or other rotating parts.

Tie up long hair and remove jewelry.

•

DO NOT exceed the generator’s wattage

amperage capacity.

Start generator and let engine stabilize

before connecting electrical loads.

NOTE:

•

CAUTION

Exceeding generators wattage/amperage capacity

could damage generator and/or electrical devices

connected to it.

Connect electrical loads in OFF position,

then turn ON for operation.

Turn electrical loads OFF and disconnect

from generator before stopping generator.

•

DO NOT use generator with electrical cords

which are worn, frayed, bare or otherwise

damaged.

DO NOT operate generator in the rain or

wet weather.

DO NOT handle generator or electrical

cords while standing in water, while

barefoot, or while hands or feet are wet.

DO NOT allow unqualified persons or

children to operate or service generator.

•

WARNING

Exhaust heat/gases could ignite combustibles,

structures or damage fuel tank causing a fire,

resulting in death or serious injury and/or

property damage.

Contact with muffler area could cause burns

resulting in serious injury.

DO NOT touch hot parts and AVOID hot

exhaust gases.

Allow equipment to cool before touching.

It is a violation of California Public Resource

Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered,

or grass-covered land unless the exhaust

system is equipped with a spark arrester, as

defined in Section 4442, maintained in

effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer,

retailer, or dealer to obtain a spark arrester

designed for the exhaust system installed on

this engine.

Replacement parts must be the same and

installed in the same position as the original

parts.

•

When using generator for backup power,

notify utility company.

Use a ground fault circuit interrupter (GFCI)

in any damp or highly conductive area,

such as metal decking or steel work.

DO NOT touch bare wires or receptacles.

•

English Customer Service: 1-844-FIRMAN1

05

•

Use generator only for intended uses.

If you have questions about intended use,

ask dealer or contact local service center.

Operate generator only on level surfaces.

DO NOT expose generator to excessive

moisture, dust, dirt, or corrosive vapors.

DO NOT insert any objects through cooling

slots.

If connected devices overheat, turn them off

and disconnect them from generator.

Shut off generator if:

-Electrical output is lost.

-Equipment sparks, smokes, or emits flames.

-Unit vibrates excessively.

•

WARNING

Medical and Life Support Uses.

In case of emergency, call 911 immediately.

NEVER use this product to power life support

devices or life support appliances.

NEVER use this product to power medical

devices or medical appliances.

Inform your electricity provider immediately

if you or anyone in your household depends

on electrical equipment to live.

Inform your electrical provider immediately

if a loss of power would cause you or anyone

in your household to experience a medical

emergency.

•

NOTE:

Improper treatment of generator could damage

it and shorten its life.

UNPACKING THE GENERATOR

•

Parts Included

Your gasoline powered generator ships with

the following parts:

1. Engin Oil(Bottle) . . . . . . . . . . . . . . . .. . . . . . . . . 1

2. Oil Funnel . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . 1

3. Wrench for Spark plug . . . . . . . . . . . . . . . . . . . .1

6. Battery Charger Cable (2 m). . . . . . . . . . . . . . . 1

7. Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

8. Quick Reference Guide . . . . . . . . . . . . . . . . . . 1

4. Screwdriver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

5. Handle Assy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

1

2

3

5

Quick

Reference

Guide

Manual

7

English Customer Service: 1-844-FIRMAN1

06

6

8

4

Page 07

English Customer Service: 1-844-FIRMAN1

Install the Handle

A

B

C

D

1. Secure the handle to the fuel tank using the

two handle bolts B(M6X30) and rubber washers C.

2. Use the supplied screwdriver to fasten securely.

DO NOT over tighten the bolts.

3. Place the plug D into the handle.

CONTROLS AND FEATURES

Generator

*We are always working to improve our products. Therefore, the enclosed product may differ

slightly from the image on this page.

①

②

③

④

⑤

⑥

⑦

⑧

⑨

⑩

⑪

1- Fuel Gauge

2- 1.3 Gallon Capacity Fuel Tank

3- Handle

4- Fuel Cap

5- Choke Lever

6- Fuel Valve

7- Air Filter

8- 80cc FIRMAN OHV Engine

9- Recoil Starter

10- Oil Filler Cap

11- Outlet Cover

12- Control Panel

®

English Customer Service: 1-844-FIRMAN1

08

⑫

Control Panel

Total power drawn from all receptacles must not exceed the name plate rating.

NOTE:

English Customer Service: 1-844-FIRMAN1

09

1

2

3

4

5

6

7

8

1

2

5

7

Ground Terminal – Consult an electrician

for local grounding regulations.

120V, 20A Outlet – (NEMA 5-20R) 20 Amp

of current may be drawn from this 120 Volt

receptacle.

8

Outlet Cover - Protect the receptacles from

dust and debris.

12V DC outlet – 8.3 Amp of DC current

may be drawn from the receptacle.

Use this outlet to charge 12V automotive

type batteries ONLY. See 12VDC outlet

(Battery Charger) section.

Engine Switch – Flip the switch to the “ON”(l)

position and pull the recoil starter to start

the generator. Turn to the “OFF”(O) position

to turn off the generator.

3

4

Voltmeter – Shows the output voltage.

6

DC Circuit Breaker – Protect the 12V DC outlet.

SPECIFICATIONS

AN IMPORTANT MESSAGE ABOUT TEMPERATURE:

When operated above 77°F(25°C) there may be a decrease in power.

Maximum wattage and current are subject to and limited by such factors as fuel BTU content

ambient temperature, altitude, engine condition and etc. Maximum power decreases about

3.5% for each 1,000 feet above sea level; and will also decrease about 1% for each 10°F(6°C)

above 60°F(16°C) ambient temperature.

•

Model

Rated AC Voltage

Phase

Power Factor

Voltage regulator

Alternator Type

Running Watts

Starting Watts

Engine

Engine Type

Displacement

Low Oil Shutdown

Ignition System

Starting System

Fuel

Capacity Fuel Tank

Lubricating Oil Capacity

Carburetor Type

Air Cleaner

P.T.O. shaft rotation

120V

P01001

1050

Capacitor

Single Phase

1

Single Cylinder, 4-Stroke OHV Air Cooled

80 cc

Breakless Ignition Type, Flywheel Magneto

Unleaded Automotive Gasoline

Recoil

1.3 Gallon

12.9 oz(0.38L)

Counter Clockwise (Facing P.T.O.)

Float

Brushless

Polyurethane Type

YES

1300

FIRMAN

Rated Fequency

60Hz

Oil Type

See “Add Engine Oil” Section

English Customer Service: 1-844-FIRMAN1

10

Total Harmonic Distortion(THD)

Standard

AC Grounding System

Neutral Bonded To Frame

Add Engine Oil

1.Place generator on a flat, level surface.

2.Clean area around oil fill and remove yellow

oil fill cap/dipstick.

3.Wipe dipstick clean.

NOTE:

The engine is equipped with a low oil shut-off and

will stop when the oil level in the crankcase falls

below the threshold level.

NOTE:

We consider the first 5 hours of run time to be

the break-in period for the unit. During the break

in period stay at or below 50% of the running

watt rating and vary the load occasionally to allow

stator windings to heat and cool. Adjusting the

load will also cause engine speed to vary and help

seat piston rings.

CAUTION

The unit is equipped with a low oil shutdown.If

the oil level becomes lower than required,the

sensor will activate a warning device or stop the

engine.

If generator shuts off and the oil level is within

specifications, check to see if generator is sitting

at an angle that forces oil to shift. Place on an

even surface to correct this. If engine fails to

start, the oil level may not be sufficient to

deactivate low oil level switch. Make sure the

sump is completely full of oil.

(H)

DRAIN PLUG

(L)

5.Replace oil fill cap/dipstick and fully tighten.

6.Oil level should be checked prior to each use

or at least every 8 hours of operation. Keep oil

level maintained.

4.Using oil funnel, slowly pour contents of

provided oil bottle into oil fill opening to the

"H" mark on dipstick. Be careful do not

overfill. Overfilling with oil could cause the

engine to not start or hard starting.

H

L

Low oil shutdown

Degrees Celsiusº(Outside)

Full Synthetic 5W-30

Degrees Fahrenheitº(Outside)

5W-30 10W-40

10W-30

CAUTION

English Customer Service: 1-844-FIRMAN1

11

Add Fuel

Fuel must meet these requirements:

•

Clean, fresh, unleaded gasoline.

Use regular UNLEADED gasoline with the

generator engine with a minimum 87 octane

/ 87 AKI (91 RON).

For high altitude use, see "Operation at High

Altitude".

Do not use gasoline with more than 10%

alcohol such as E85 or ethanol.

•

Failure to follow Operator's Manual for fuel

recommendations voids warranty.

Avoid generator damage.

DO NOT use unapproved gasoline such as E85.

DO NOT mix oil in gasoline.

DO NOT modify engine to run on alternate fuels.

•

WARNING

Fuel and its vapors are extremely flammable

and explosive which could cause burns, fire or

explosion resulting in death, serious injury

and/or property damage.

WHEN ADDING FUEL

Fill fuel tank outdoors.

DO NOT overfill tank. Allow space for fuel

expansion. If the tank is overfilled, fuel

can overflow onto a hot engine and cause fire

or explosion. Wipe up any spilled fuel

immediately.

If fuel spills, wait until it evaporates before

starting engine.

Keep fuel away from sparks, open flames,

pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap and fittings

frequently for cracks or leaks. Replace if

necessary.

DO NOT light a cigarette or smoke when

filling the fuel tank.

•

1.Clean area around fuel fill cap, remove cap.

2.Slowly add unleaded fuel to fuel tank. Be

careful not to fill above the red fuel level

indicator . This allows adequate space for

fuel expansion.

3.Install fuel cap and let any spilled fuel

evaporate before starting engine or wipe up

any spilled gasoline.

English Customer Service: 1-844-FIRMAN1

12

CAUTION

Slowly add unleaded gasoline to fuel tank.

Do not overfill tank.

Do not fill above the red line indicator.

This will allow expansion in hot weather

and prevent overflow.

•

Red Line Indicator

IMPORTANT: It is important to prevent gum

deposits from forming in fuel system parts such

as the carburetor, fuel hose or tank during storage.

Alcohol-blended fuels (called gasohol, ethanol

or methanol) can attract moisture, which leads to

separation and formation of acids during storage.

Acidic gas can damage the fuel system of an engine

while in storage. To avoid engine problems, the

fuel system should be emptied before storage of

30 days or longer. See the " Long Term Storage"

section. Never use engine or carburetor cleaner

products in the fuel tank as permanent damage

may occur.

Operation at High Altitude

At altitudes over 5,000 feet(1524 meters), a

minimum 85 octane / 85 AKI (89 RON) gasoline

is acceptable.

The density of air at high altitude is lower

than at sea level. Engine power is reduced

as the air mass and air-fuel ratio decrease.

Engine power and generator output will be

reduced approximately 3.5% for every 1000 feet

of elevation above sea level. This is a

natural trend and cannot be changed by

adjusting the engine. At high altitudes

Altitude main jet 1

Altitude main jet 2

80cc

312715083

312715084

Altitude

3000-6000Feet

6000-8000Feet

English Customer Service: 1-844-FIRMAN1

13

OPEN

WARNING

Grounding

The National Electric Code requires your generator

must be properly connected to an appropriate

ground to help prevent electric shock.

Failure to properly ground the

generator can result in electric

shock.

WARNING

THERE IS A PERMANENT CONDUCTOR BETWEEN

THE GENERATOR (STATOR WINDING) AND THE

FRAME.

Use approved transfer equipment to prevent

backfeed by isolating generator from electric

utility workers.

When using generator for backup power, notify

utility company.

Use a ground fault circuit interrupter (GFCI) in

any damp or highly conductive area, such as

metal decking or steel work.

DO NOT touch bare wires or receptacles.

DO NOT use generator with electrical cords

which are worn,frayed, bare or otherwise

damaged.

DO NOT operate generator in the rain or wet

weather.

DO NOT handle generator or electrical cords

while standing in water, while barefoot, or

while hands or feet are wet.

DO NOT allow unqualified persons or children

to operate or service generator.

Connecting to a Building's Electrical System

WARNING

Generator voltage could cause

electrical shock or burn resulting

in death or serious injury.

•

The part number and recommended minimum

altitude for the application of the high

altitude carburetor main jet is listed in the

table below.

main jet and installation instructions can be

obtained by contacting Customer Support.

Installation instructions are also available in the

Technical Bulletin area of the FIRMAN internet site.

increased exhaust emissions can also result due to

the increased enrichment of the air fuel ratio.

Other high altitude issues can include hard

starting, increased fuel consumption and

spa r k pl u g fo u lin g. T o a lle via t e hi g h

al titude is sues other th an the natura l

power loss, FIRMAN can provide a high

altitude carburetor main jet. The alternative

OPERATION

Generator Location

Make sure you review each warning in order to

prevent fire hazard.

Keep area clear of inflammables or other

hazardous materials.

Select a site that is dry, well ventilated and

protected from the weather.

Keep exhaust pipe clear of foreign objects.

Keep generator away from open flame.

Keep generator on a stable and level surface.

WARNING

Surge Protection

Voltage fluctuation may impair the proper

functioning of sensitive electronic equipment.

WARNING

POISONOUS GAS HAZARD.

•

Do not block generator air vents with paper or

other material.

CAUTION

Tilting can cause fuel spillage.

CAUTION

English Customer Service: 1-844-FIRMAN1

14

Starting the Generator

1. Before starting the generator, check for loose

or missing parts and for any damage which

may have occurred during shipment.

2. Check oil level and fuel.

6. Move the choke lever to the “CHOKE” position.

5. Flip the engine switch to the “ON”(l) position.

8. Do not over-choke. As soon as engine starts

and warm up, move the choke lever to the

“RUN” position.

9. Allow generator to run at no load for few

minutes upon each initial start-up to permit

engine and generator to stablize.

WARNING

When starting engine, pull cord slowly until

resistance is felt and then pull rapidly to avoid

kickback.

4. Turn the fuel valve to the “ON”(l) position.

7. Pull the starter cord slowly until resistance is

felt and then pull rapidly.

3. Disconnect all electrical loads from the

generator. Never start or stop the generator

with electrical devices plugged in or turned

on.

English Customer Service: 1-844-FIRMAN1

15

Keep choke lever in “CHOKE” position for only 1

pull of the recoil starter. After first pull, move

choke lever to the “RUN” position for up to the

next 3 pulls of the recoil starter. Too much

choke leads to sparkplug fouling/engine

flooding due to the lack of incoming air. This

will cause the engine not to start.

Connecting Electrical Loads

1.Let engine stabilize and warm up for a few

minutes after starting.

2.Ensure circuit breaker on control panel is in

on position.

This unit has been pretested and adjusted to

handle its full capacity. Before starting the

generator, disconnect all load. Apply load only

after generator is running. Voltage is regulated

via the engine speed adjusted at the factory for

correct output. Readjusting will void warranty.

CAUTION

When applying a load, do not exceed the maximum

wattage rating of the generator when using one or

more receptacles. Also, do not exceed the amperage

rating of any one receptacle.

Do not apply heavy electrical load during break-in

period (the first five hours of operations).

3.Plug in and turn on the desired 120 Volt

AC, single phase, 60Hz electrical loads. It is

better to attach the item with largest load first.

12V DC Outlet (Battery Charger)

The 12V DC outlet is ONLY to be used with the

supplied 12V battery charging cable. The DC

output is unregulated and will damage other

12V DC products.

CAUTION

1. Before connecting the battery charging cable

to a battery that is installed in a vehicle, disconnect

the vehicle battery ground cable from the

negative (–) battery terminal.

Storage batteries give off EXPLOSIVE hydrogen

gas while charging. Do not allow smoking, open

flames, sparks, or spark producing equipment

in the area while charging.

WARNING

Battery electrolyte fluid is comprised of sulfuric

acid that can be very dangerous and cause severe

burns. Do not allow this fluid to contact eyes, skin,

clothing, etc. If contact or spillage does occur,

flush the area with water immediately.

WARNING

Do not continue to charge a battery that becomes

hot or is fully charged.

The amount of current flowing will depend on the

charging voltage and battery's state of charge. As

the battery becomes more fully charged, the output

current to the battery decreases and nearly becomes

constant. Taper chargers are intended to be used

with the provision that they will be disconnected

from the battery after a maximum time on charge.

Normally a period of 30 to 120 minutes is sufficient

to recharge a weak battery. The charge level of the

battery should be checked periodically.

English Customer Service: 1-844-FIRMAN1

16

Do not start the vehicle while the battery charging

Cable is connected and the generator is running.

It will not give the battery a boost of power. The

Vehicle or the generator may be damaged. Charge

only vented wet lead acid batteries. Other types

of batteries may burst, causing personal injury

or damage.

2. Press the engine switch to the “OFF”(O) position.

A DC circuit protector has been provided to

protect the circuit from overloads. If an overload

occurs, the circuit protector will trip. The circuit

protector may be reset by pushing the button of

the protector.

DC CIRCUIT PROTECTOR

Charging a large capacity battery or a totally

discharged battery may cause the DC breaker to

turn off. In these cases, a separate battery charger

unit connected to an AC power source is

recommended instead of the DC receptacle on

the generator.

Stopping the Engine

Let the generator run at no-load for two

minutes to stabilize internal temperatures

of the engine and generator.

1. Turn off and remove entire electrical loads.

Never start or stop the generator with

electrical devices plugged in or turned on.

WARNING

Fuel and its vapors are extremely flammable and

explosive which could cause burns, fire or

explosion resulting in death, serious injury

and/or property damage.

DO NOT stop engine by moving choke control

to “START” position.

Important: Always ensure that the Fuel Valve

and the Engine Switch are in the “OFF” position

when the engine is not in use.

If the engine will not be used for a period of two

weeks or longer, please see the Storage section

for proper engine and fuel storage.

2. Plug the battery charging cable into the DC

receptacle of the generator.

3. Connect the red (+) battery charger lead to the

red (+) battery terminal.

4. Connect the black (–) battery charger lead to

the black (–) battery terminal.

5. Start the generator.

NOTE:

When the battery circuit is in use the AC capacity

is reduced by 100 watts. Make sure the combined

load is within the rated limits.

WARNING

Do not continue to charge a battery that becomes

hot or is fully charged.

If a cover is used, do not install until unit has cooled.

3. Turn the fuel valve to the “OFF”(O) position.

Do not leave the generator until it has

completely stopped.

English Customer Service: 1-844-FIRMAN1

17

Do not expose to rain.

Charge only 12v lead-acid batteries. Other types

of batteries may burst causing personal injury

and damage.

Risk of explosive gas mixture. Read instructions

in owner’s guide before using charger.

La page charge ...

Firman P01001 Mode d'emploi

Firman P01001 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents