Firman P03607 Le manuel du propriétaire

P/N:336745454 Rev:00

OWNER’S MANUAL

Read all safety precautions and instructions carefully

before operating equipment.

Ensure engine is stopped and level before performing

any maintenance or service.

IMPORTANT:

Record product information to reference when ordering parts or

obtaining warranty coverage.

Serial Number:

PORTABLE GENERATOR

MODEL NUMBER

P03605

Rev Level:00

DO NOT RETURN TO

STORE!

CALL US FIRST!

CUSTOMER HOTLINE

1-844-347-6261

FOR QUESTIONS OR SERVICE

INFORMATION

Purchase Date:

Table of Contents

English Customer Service: 1-844-FIRMAN1

. . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Safety Precautions . . . . . . . . . . . . . . . . . . . . .2

Unpacking the Generator. . . . . . . . . . . . . . . .6

Parts Included. . . . . . . . . . . . . . . . . . . . . . . .6

Removal of Shipping Supports . . . . . . . . . 7

Controls and Features. . . . . . . . . . . . . . . . . .8

Generator. . . . . . . . . . . . .. . . . . . . . . . . . . .8

Control Panel. . . . . . . . . . . . . . . . . . . . . . . 9

Specifications. . . . . . . . . . . . . . . . . . . . . . . . 10

Add Engine Oil . . . . . . . . . . . . . . . . . . . . . . 11

Low Oil Shutdown . . . . . . . . . . . . . . . . . . .11

Add Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Operation at High Altitude . . . . . . . . . . .12

Grounding. . . . .. . . . . . . . . . . . . . . .. . . . . .13

System.. . . . . . . . . . . . . . . . . . . . . . .. . . . . .13

Operation . . . . . . . . . . . . . . . . . . . . . . . . .. . . . 14

Generator Location . . . . . . . . . . . . . . . . . . 14

Surge Protection . . . . . . . . . . . . .. . . . . . . .14

Starting the Generator . . . . . . . . . . . .. . . 15

Connecting Electrical Loads . . . . . . . .. . . 16

Stopping the Engine . . . . . . . . . . . . . . . . . 16

Low Oil Shutdown . . . . . . . . . . . . . . . . . . 17

Do Not Overload Generator . . . . . . . . . . . 17

Introduction

Connecting to a Building’s Electrical

Maintenance And Storage. . . . . . . . . . . . . . 18

Maintenance Schedule . . . . . . . . . . . . . 18

Engine Maintenance .. . . . . . . . . . . .. . . . 19

Change Engine Oil . . .. . . . . . . . . . . . . . 19

Air Filter Maintenance. . . . . . . . . . . . . .19

Spark Plug Maintenance. . . . . . . . . . . . 20

Cleaning Fuel Strainer . . . . . . . . . . . . 20

. . . 20

Generator Maintenance . . . . . . . . . . . . . . 21

Service and Storage . . . . . . . . . . . . . . . .. 22

Trouble Shooting . . . . . . . . . . . . . . . . . . . . .23

Parts Diagram and Parts List . . . . . . . . . . 24

Generator Parts Diagram . . . . . . . . . . . . 24

Engine Parts Diagram . . . . . . . . . .. . . . . 25

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . 26

Service Information . . . . . . . . . . . . . .. . . . . 28

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Inspect Muffler and Spark Arrester

Thank you for purchasing a FIRMAN generator.

Page 01

Important Safety Information

The manufacturer cannot possibly anticipate every possible circumstance that might involve a

hazard. The warnings in this manual and the tags and decals affixed to the unit are therefore not

all-inclusive. If you use a procedure, work method or operating technique that the manufacturer

does not specifically recommend you must satisfy yourself that it is safe for you and others. You

must also make sure that the procedure work method or operating technique that you choose

does not render the generator unsafe.

DANGER WARNING CAUTION

DANGER indicates a

potentially hazardous

situation which, if not

avoided. WILL result in

death or serious injury.

WARNING indicates a

potentially hazardous

situation which, if not

avoided, could result in

death or serious injury.

CAUTION indicates a

potentially hazardous

situation which, if not

avoided, may result in minor

or moderate personal injury,

or property damage.

Toxic Fumes

Fire Hazard

Hot Surface.

Do Not Touch the Surface.

Kickback

Risk of Electric Shock

Explosion Hazard

Rotating Parts Entanglement

Hazard

Operator’s Manual

INTRODUCTION

English Customer Service: 1-844-FIRMAN1

SAFETY PRECAUTIONS

Page 02

WARNING

POISONOUS GAS HAZARD.

•

WARNING

•

English Customer Service: 1-844-FIRMAN1

Page 03

CORRECT USAGE

Example location to reduce risk of carbon monoxide poisoning

•

ONLY use outside and downwind, far away from windows, doors and vents.

•

Direct exhaust away from occupied spaces.

INCORRECT USAGE

Do not operate in any of the following locations:

Near any door, window or vent

Garage

Basement

Crawl Space

Living Area

Attic

Entry Way

Porch

Mudroom

English Customer Service: 1-844-FIRMAN1

Page 04

WHEN OPERATING EQUIPMENT

•

DO NOT tip engine or equipment at angle

which causes fuel to spill.

DO NOT stop engine by moving choke

control to “Start” position.

•

WHEN TRANSPORTING, MOVING

OR REPAIRING EQUIPMENT

Transport/move/repair with fuel tank

EMPTY or with fuel shutoff valve OFF.

•

DO NOT tip engine or equipment at angle

which causes fuel to spill.

Disconnect spark plug wire.

•

WHEN STORING FUEL OR EQUIPMENT

WITH FUEL IN TANK

•

WARNING

•

WARNING

Generator voltage could cause

electrical shock or burn resulting

in death or serious injury.

•

WARNING

•

NEVER start or stop engine with electrical

devices plugged in and turned on.

WARNING

Fuel and its vapors are extremely flammable

and explosive which could cause burns, fire,

or explosion resulting in death or serious

injury and/or property damage.

WHEN ADDING OR DRAINING FUEL

Turn generator engine OFF and let it cool at

least 2 minutes before removing fuel cap.

Loosen cap slowly to relieve pressure in tank.

Fill or drain fuel tank outdoors.

•

DO NOT overfill tank. Allow space for fuel

expansion.

If fuel spills, wait until it evaporates before

starting engine.

•

Keep fuel away from sparks, open flames,

pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap, and fittings

frequently for cracks or leaks. Replace if

necessary.

DO NOT light a cigarette or smoke.

•

WHEN STARTING EQUIPMENT

Ensure spark plug, muffler, fuel cap, and air

cleaner are in place.

•

DO NOT crank engine with spark plug

removed.

•

Use approved transfer equipment, suitable

for the intended use, to prevent backfeed by

isolating generator from electric utility

workers.

English Customer Service: 1-844-FIRMAN1

Page 05

WARNING

Unintentional sparking

could cause fire or

electric shock resulting

in death or serious

injury.

WHEN ADJUSTING OR MAKING REPAIRS TO

YOUR GENERATOR

Disconnect the spark plug wire from the

spark plug and place the wire where it cannot

contact spark plug.

•

WHEN TESTING FOR ENGINE SPARK

Use approved spark plug tester.

•

DO NOT check for spark with spark plug

removed.

•

WARNING

NEVER operate generator without protective

housing or covers.

DO NOT wear loose clothing, jewelry or

anything that could be caught in the starter

or other rotating parts.

Tie up long hair and remove jewelry.

•

DO NOT exceed the generator’s wattage

amperage capacity.

Start generator and let engine stabilize

before connecting electrical loads.

NOTE:

•

CAUTION

Exceeding generators wattage/amperage capacity

could damage generator and/or electrical devices

connected to it.

Connect electrical loads in OFF position,

then turn ON for operation.

Turn electrical loads OFF and disconnect

from generator before stopping generator.

•

DO NOT use generator with electrical cords

which are worn, frayed, bare or otherwise

damaged.

DO NOT operate generator in the rain or

wet weather.

DO NOT handle generator or electrical

cords while standing in water, while

barefoot, or while hands or feet are wet.

DO NOT allow unqualified persons or

children to operate or service generator.

•

WARNING

Exhaust heat/gases could ignite combustibles,

structures or damage fuel tank causing a fire,

resulting in death or serious injury and/or

property damage.

Contact with muffler area could cause burns

resulting in serious injury.

DO NOT touch hot parts and AVOID hot

exhaust gases.

Allow equipment to cool before touching.

It is a violation of California Public Resource

Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered,

or grass-covered land unless the exhaust

system is equipped with a spark arrester, as

defined in Section 4442, maintained in

effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer,

retailer, or dealer to obtain a spark arrester

designed for the exhaust system installed on

this engine.

Replacement parts must be the same and

installed in the same position as the original

parts.

•

When using generator for backup power,

notify utility company.

Use a ground fault circuit interrupter (GFCI)

in any damp or highly conductive area,

such as metal decking or steel work.

DO NOT touch bare wires or receptacles.

•

English Customer Service: 1-844-FIRMAN1

Page 06

•

Use generator only for intended uses.

If you have questions about intended use,

ask dealer or contact local service center.

Operate generator only on level surfaces.

DO NOT expose generator to excessive

moisture, dust, dirt, or corrosive vapors.

DO NOT insert any objects through cooling

slots.

If connected devices overheat, turn them off

and disconnect them from generator.

Shut off generator if:

-Electrical output is lost.

-Equipment sparks, smokes, or emits flames.

-Unit vibrates excessively.

•

WARNING

Medical and Life Support Uses.

In case of emergency, call 911 immediately.

NEVER use this product to power life support

devices or life support appliances.

NEVER use this product to power medical

devices or medical appliances.

Inform your electricity provider immediately

if you or anyone in your household depends

on electrical equipment to live.

Inform your electrical provider immediately

if a loss of power would cause you or anyone

in your household to experience a medical

emergency.

•

NOTE:

Improper treatment of generator could damage

it and shorten its life.

UNPACKING THE GENERATOR

•

Parts Included

Your gasoline powered generator ships with

the following parts:

English Customer Service: 1-844-FIRMAN1

1. Engine Oil(Bottle) . . . . . . . . . . . . . . . . . . . . . . . 1

2. Oil Funnel . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . 1

3. Wrench for Spark plug . . . . . . . . . . . . . . . . . . . .1

5. Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

6. Quick Reference Guide . . . . . . . . . . . . . . . . . . . 1

4. Double Open wrench (10mm & 12mm). . . . 2

2

1

Quick

Reference

Guide

3

Manual

6

5

4

Page 07

REMOVAL OF SHIPPING SUPPORTS

Before you can run your new generator, follow

these simple instructions:

CAUTION

Failure to remove these items can result

in damage to your generator, possible

Personal injury and void your warranty.

Refer to the following instructions and pictures

to remove the attached engine support brackets

(red) under the engine.

3. You may discard these brackets, as they are no longer

required for normal operation of your generator.

Your generator is now ready for use. Refer to

your owner's manual for proper oil fill and

startup instructions.

Engine Support Brackets

(red color)

Remove these 4 nuts &

bolts as indicated.

Supplied wrenches

English Customer Service: 1-844-FIRMAN1

Page 08

CONTROLS AND FEATURES

Generator

1- Fuel Gauge

2- 5.0 Gallon Capacity Fuel Tank

3- Fuel Cap

4- Choke Lever

5- Fuel Valve

6- Air Filter

7- 208cc FIRMAN OHV Engine

8- Recoil Starter

9-

10- Outlet Cover

11- Control Panel

Oil Filler Cap

*We are always working to improve our products. Therefore, the enclosed product may differ

slightly from the image on this page.

English Customer Service: 1-844-FIRMAN1

1

2

①

②

③

④

⑤

⑥

⑦

⑧

⑨

⑩

⑪

®

Page 09

Control Panel

1

2

4-1 Data-Minder(Multi-Meter) – Push the

SELECT button to show the Voltage, Hertz and

running hours. If the low oil indicator is lit,

check the oil level.

9

8

6

7

Ground Terminal – Consult an electrician

for local grounding regulations.

120V, 20A Duplex (NEMA 5-20R)

5

120V, 30A RV (NEMA TT-30R)

Total power drawn from all receptacles must not exceed the name plate rating.

NOTE:

Outlet Cover - Protect the receptacles from

dust and debris.

3

120/240V, 30A Twist-Lock – (NEMA L14-

30R) May be used to supply power for the

operation of 120/240 Volt, 30Amp.

4

Voltage Selector Switch – To select

between 120 Volt or 240 Volt.

1

2

3

4

5

6

7

8

9

240V

120V

A - Digital display

B - AC voltage indicator

C - Frequency indicator

D - Hour indicator

E - Low oil indicator

F - Select button

English Customer Service: 1-844-FIRMAN1

Maximum full load 30 Amp current may be

drawn from this 120 Volt receptacle.

20 Amp of current may be drawn from this

120 Volt receptacle.

Engine Switch – Flip the switch to the “ON(l)”

position and pull the recoil starter to start the

generator. Turn to the “OFF(O)” position to

turn off the generator.

9

Page 10

SPECIFICATIONS

Model

Rated AC Voltage

Phase

Power Factor

Voltage Regulator

Alternator Type

Running Watts

Starting Watts

Engine

Engine Type

Displacement

Low Oil Shutdown

Ignition System

Starting System

Fuel

Capacity Fuel Tank

Lubricating Oil Capacity

Carburetor Type

Air Cleaner

P.T.O. Shaft Rotation

120/240V

P03605

3650

AVR

Single

1

Single Cylinder, 4-Stroke OHV Air Cooled

208cc

Breakless Ignition Type, Flywheel Magneto

Unleaded Automotive Gasoline

Recoil

5.0 Gallon

20.3 oz(0.6L)

Counter Clockwise (Facing P.T.O.)

Float

Brushed

Polyurethane Type

Yes

4550

FIRMAN

Rated Fequency

60Hz

Oil Type

See “Add Engine Oil” Section

Spark Plug

AN IMPORTANT MESSAGE ABOUT TEMPERATURE:

When operated above 77°F(25°C) there may be a decrease in power.

Maximum wattage and current are subject to and limited by such factors as fuel BTU content

ambient temperature, altitude, engine condition and etc. Maximum power decreases about

3.5% for each 1,000 feet above sea level; and will also decrease about 1% for each 10°F(-12.2°C)

above 60°F(16°C) ambient temperature.

•

TORCH F6RTC/NGK BPR6ES/CHAMPION RN9YC

English Customer Service: 1-844-FIRMAN1

ADD ENGINE OIL

Page 11

1.Place generator on a flat, level surface.

2.Clean area around oil fill and remove yellow

oil fill cap/dipstick.

3.Wipe dipstick clean.

NOTE:

The engine is equipped with a low oil shut-off and

will stop when the oil level in the crankcase falls

below the threshold level.

NOTE:

We consider the first 5 hours of run time to be

the break-in period for the unit. During the break

in period stay at or below 50% of the running

watt rating and vary the load occasionally to allow

stator windings to heat and cool. Adjusting the

load will also cause engine speed to vary and help

seat piston rings.

CAUTION

The unit is equipped with a low oil shutdown.If

the oil level becomes lower than required,the

sensor will activate a warning device or stop the

engine.

If generator shuts off and the oil level is within

specifications, check to see if generator is sitting

at an angle that forces oil to shift. Place on an

even surface to correct this. If engine fails to

start, the oil level may not be sufficient to

deactivate low oil level switch. Make sure the

sump is completely full of oil.

(H)

DRAIN PLUG

(L)

5.Replace oil fill cap/dipstick and fully tighten.

6.Oil level should be checked prior to each use

or at least every 8 hours of operation. Keep oil

level maintained.

4.Using oil funnel, slowly pour contents of

provided oil bottle into oil fill opening to the

"H" mark on dipstick. Be careful do not

overfill. Overfilling with oil could cause the

engine to not start or hard starting.

H

L

Low oil shutdown

Degrees Celsiusº(Outside)

Full Synthetic 5W-30

Degrees Fahrenheitº(Outside)

5W-30 10W-40

10W-30

CAUTION

English Customer Service: 1-844-FIRMAN1

ADD FUEL

Page 12

Fuel must meet these requirements:

•

Clean, fresh, unleaded gasoline.

Use regular UNLEADED gasoline with the

generator engine with a minimum 87 octane

/ 87 AKI (91 RON).

For high altitude use, see "Operation at High

Altitude".

Do not use gasoline with more than 10%

alcohol such as E85 or ethanol.

•

Failure to follow Operator's Manual for fuel

recommendations voids warranty.

Avoid generator damage.

DO NOT use unapproved gasoline such as E85.

DO NOT mix oil in gasoline.

DO NOT modify engine to run on alternate fuels.

•

WARNING

Fuel and its vapors are extremely flammable

and explosive which could cause burns, fire or

explosion resulting in death, serious injury

and/or property damage.

WHEN ADDING FUEL

Fill fuel tank outdoors.

DO NOT overfill tank. Allow space for fuel

expansion. If the tank is overfilled, fuel

can overflow onto a hot engine and cause fire

or explosion. Wipe up any spilled fuel

immediately.

If fuel spills, wait until it evaporates before

starting engine.

Keep fuel away from sparks, open flames,

pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap and fittings

frequently for cracks or leaks. Replace if

necessary.

DO NOT light a cigarette or smoke when

filling the fuel tank.

•

1.Clean area around fuel fill cap, remove cap.

2.Slowly add unleaded fuel to fuel tank. Be

careful not to fill above the red fuel level

indicator . This allows adequate space for

fuel expansion.

3.Install fuel cap and let any spilled fuel

evaporate before starting engine or wipe up

any spilled gasoline.

CAUTION

Slowly add unleaded gasoline to fuel tank.

Do not overfill tank.

Do not fill above top of fuel screen. This

will all expansion in hot weather and

prevent overflow.

•

Operation at High Altitude

At altitudes over 5,000 feet(1524 meters), a

minimum 85 octane / 85 AKI (89 RON) gasoline

is acceptable.

The density of air at high altitude is lower

than at sea level. Engine power is reduced

as the air mass and air-fuel ratio decrease.

Engine power and generator output will be

reduced approximately 3.5% for every 1000 feet

of elevation above sea level. This is a

natural trend and cannot be changed by

adjusting the engine. At high altitudes

increased exhaust emissions can also result

due to the increased enrichment of the air

fuel ratio.

Other high altitude issues can include hard

starting, increased fuel consumption and

spark plug fouling. To alleviate high

altitude issues other than the natural

power loss, FIRMAN can provide a high

altitude carburetor main jet. The alternative

English Customer Service: 1-844-FIRMAN1

Page 13

Altitude main jet 1

Altitude main jet 2

208cc

335717002

335717003

Altitude

3000-6000Feet

6000-8000Feet

OPEN

WARNING

Grounding

The National Electric Code requires your generator

must be properly connected to an appropriate

ground to help prevent electric shock.

Failure to properly ground the

generator can result in electric

shock.

WARNING

THERE IS A PERMANENT CONDUCTOR BETWEEN

THE GENERATOR (STATOR WINDING) AND THE

FRAME.

Use approved transfer equipment to prevent

backfeed by isolating generator from electric

utility workers.

When using generator for backup power, notify

utility company.

Use a ground fault circuit interrupter (GFCI) in

any damp or highly conductive area, such as

metal decking or steel work.

DO NOT touch bare wires or receptacles.

DO NOT use generator with electrical cords

which are worn,frayed, bare or otherwise

damaged.

DO NOT operate generator in the rain or wet

weather.

DO NOT handle generator or electrical cords

while standing in water, while barefoot, or

while hands or feet are wet.

DO NOT allow unqualified persons or children

to operate or service generator.

Connecting to a Building's Electrical System

WARNING

Generator voltage could cause

electrical shock or burn resulting

in death or serious injury.

•

The part number and recommended minimum

altitude for the application of the high

altitude carburetor main jet is listed in the

table below.

main jet and installation instructions can be

obtained by contacting Customer Support.

Installation instructions are also available in the

Technical Bulletin area of the FIRMAN internet site.

English Customer Service: 1-844-FIRMAN1

OPERATION

Page 14

Generator Location

Make sure you review each warning in order to

prevent fire hazard.

Keep area clear of inflammables or other

hazardous materials.

Select a site that is dry, well ventilated and

protected from the weather.

Keep exhaust pipe clear of foreign objects.

Keep generator away from open flame.

Keep generator on a stable and level surface.

WARNING

Surge Protection

Voltage fluctuation may impair the proper

functioning of sensitive electronic equipment.

WARNING

POISONOUS GAS HAZARD.

•

Do not block generator air vents with paper or

other material.

CAUTION

Tilting can cause fuel spillage.

CAUTION

English Customer Service: 1-844-FIRMAN1

Page 15

Starting the Generator

1. Before starting the generator, check for loose

or missing parts and for any damage which

may have occurred during shipment.

2. Check oil level and fuel.

6. Move the choke lever to the “START” position.

5. Flip the engine switch to the “ON”(l) position.

8. Do not over-choke. As soon as engine starts

and warms up, move the choke lever to the

“RUN” position.

9. Allow generator to run at no load for few

minutes upon each initial start-up to permit

engine and generator to stablize.

WARNING

When starting engine, pull cord slowly until

resistance is felt and then pull rapidly to avoid

kickback.

4. Turn the fuel valve to the “ON” (l)position.

7. Pull the starter cord slowly until resistance is

felt and then pull rapidly.

3. Disconnect all electrical loads from the

generator. Never start or stop the generator

with electrical devices plugged in or turned

on.

English Customer Service: 1-844-FIRMAN1

Keep choke lever in “START” position for only 1

pull of the recoil starter. After first pull, move

choke lever to the “RUN” position for up to the

next 3 pulls of the recoil starter. Too much

choke leads to sparkplug fouling/engine

flooding due to the lack of incoming air. This

will cause the engine not to start.

Page 16

Connecting Electrical Loads

1.Let engine stabilize and warm up for a few

minutes after starting.

2.Ensure circuit breaker on control panel is in

on position.

Stopping the Engine

1. Turn off and remove entire electrical loads.

Never start or stop the generator with

electrical devices plugged in or turned on.

This unit has been pretested and adjusted to

handle its full capacity. Before starting the

generator, disconnect all load. Apply load only

after generator is running. Voltage is regulated

via the engine speed adjusted at the factory for

correct output. Readjusting will void warranty.

CAUTION

When applying a load, do not exceed the maximum

wattage rating of the generator when using one or

more receptacles. Also, do not exceed the amperage

rating of any one receptacle.

Do not apply heavy electrical load during break-in

period (the first five hours of operations).

Let the generator run at no-load for two

minutes to stabilize internal temperatures

of the engine and generator.

2. Press the engine switch to the “OFF”(O) position.

3. Turn the fuel valve to the “OFF”(O) position.

Do not leave the generator until it has

completely stopped.

English Customer Service: 1-844-FIRMAN1

4.Plug in and turn on the desired 120 or 240 Volt

AC, single phase, 60Hz electrical loads. It is

better to attach the item with largest load first.

3. Turn on voltage selector to desired 120 Volt or

240 Volt. When voltage selector is 120 Volt position,

120 Volt is supplied to 120 Volt outlets including

TT-30R and 5-20R outlets (items 5 and 6 in Control

Panel Section). When voltage selector is in 240 Volt

position, 120/240 Volt is supplied just to outlet

L14-30R (item 3 in Control Panel Section).

Page 17

Do Not Overload Generator

DO NOT stop engine by moving choke control

to “START” position.

Important: Always ensure that the Fuel Valve

and the Engine Switch are in the “OFF” position

when the engine is not in use.

If the engine will not be used for a period of two

weeks or longer, please see the Storage section

for proper engine and fuel storage.

Low Oil Shutdown

If the engine oil drops below a preset level, an

oil switch will stop the engine. Check oil level

with dipstick.

If oil level is between LOW and HIGH mark on

dipstick:

1.DO NOT try to restart the engine.

2.Contact an Authorized FIRMAN Service Dealer.

3.DO NOT operate engine until oil level is

corrected.

If oil level is below LOW mark on dipstick:

1.Add oil to bring level to HIGH mark.

2.Restart engine and if the engine stops again

a low oil condition may still exist. DO NOT try

to restart the engine.

3.Contact an Authorized FIRMAN Service Dealer.

4.DO NOT operate engine until oil level is

corrected.

Overloading a generator in excess of its rated

wattage capacity can result in damage to the

generator and to connected electrical devices.

To prolong the life of your generator and

attached devices, follow these steps to add

electrical load:

1. Start the generator with no electrical load

attached.

2. Allow the engine to run for several minutes

to stabilize.

3. Plug in and turn on the first item. It is best to

attach the item with the largest load first.

4. Allow the engine to stabilize.

5. Plug in and turn on the next item.

6. Allow the engine to stabilize.

7. Repeat steps 5-6 for each additional item.

WARNING

If a cover is used, do not install until unit has cooled.

Fuel and its vapors are extremely flammable

and explosive which could cause burns, fire or

explosion resulting in death, serious injury

and/or property damage.

English Customer Service: 1-844-FIRMAN1

MAINTENANCE AND STORAGE

MAINTENANCE SCHEDULE

Page 18

ITEM NOTES

Daily(Before

operation)

Initial

25 hours

Every

50 hours

Every

100 hours

(or annual)

Fittings/

Fasteners

Spark Plug

Engine Oil

Air Filter

Fuel Filter

Fuel Line

Exhaust

System

Carburetor

Starting

System

Check condition. Adjust gap

and clean. Replace if necessary.

Check oil level.

Clean, replace if necessary.

Clean fuel filter and fuel tank

strainer. Replace if necessary.

Check for leakage. Retighten or

replace gasket if necessary.

Check choke operation.

Check recoil starter operation.

Check. Replace if necessary.

Check fuel hose for cracks or other

damage. Replace if necessary.

√

General Recommendations

Regular maintenance will improve the performance and extend the life of the generator. See any

authorized dealer for service.

The generator's warranty does not cover items that have been subjected to operator abuse or

negligence. To receive full value from the warranty, the operator must maintain the generator as

instructed in this manual.

Some adjustments will need to be made periodically to properly maintain your generator.

All service and adjustments should be made at least once each season. Follow the requirements

in the Maintenance Schedule chart above.

Notice Once a year you should clean or replace the spark plug and replace the air filter. New

spark plugs and clean air filter assure proper fuel-air mixture and help your engine run better

and last longer.

Replace.

Check spark arrester screen.

Clean/Replace if necessary.

English Customer Service: 1-844-FIRMAN1

La page charge ...

Firman P03607 Le manuel du propriétaire

Firman P03607 Le manuel du propriétaire

dans d''autres langues

Documents connexes