Firman P01201 Manuel utilisateur

P/N:312745460 Rev:03

OWNER’S MANUAL

Read all safety precautions and instructions carefully

before operating equipment.

Ensure engine is stopped and level before performing

any maintenance or service.

IMPORTANT:

Record product information to reference when ordering parts or

obtaining warranty coverage.

Serial Number:

PORTABLE GENERATOR

MODEL NUMBER

P01201

Rev Level:03

DO NOT RETURN TO

STORE!

CALL US FIRST!

CUSTOMER HOTLINE

1-844-347-6261

FOR QUESTIONS OR SERVICE

INFORMATION

Purchase Date:

Table of Contents

. . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Safety Precautions . . . . . . . . . . . . . . . . . . . . .2

Unpacking the Generator. . . . . . . . . . . . . . . .6

Parts Included. . . . . . . . . . . . . . . . . . . . . . . .6

Removal Of Shipping Supports . . . . . . . . . 7

Controls and Features. . . . . . . . . . . . . . . . . 8

Generator. . . . . . . . . . . . .. . . . . . . . . . . . . .8

Control Panel. . . . . . . . . . . . . . . . . . . . . . . 9

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . 10

Add Engine Oil . . . . . . .. . . . . . . . . . . . . . . .11

Low Oil Shutdown . . . . . . . . . . . . . . . . . . . .11

Add Fuel . . . . . . .. . . . . . . . . . . . . . . . . . . . .12

Operation at High Altitude . . . . . . . . . . .12

Grounding. . . . .. . . . . . . . . . . . . . . .. . . . . .13

System.. . . . . . . . . . . . . . . . . . . . . . .. . . . . .13

Operation . . . . . . . . . . . . . . . . . . . . . . . . .. . . . 14

Generator Location . . . . . . . . . . . . . . . . . . 14

Surge Protection . . . . . . . . . . . . .. . . . . . . .14

Starting the Generator. . . . . . . . . .. . . . . . 15

Connecting Electrical Loads . . . . . . . .. . . 16

Stopping the Engine . . . . . . . . . . . . . . . . . 16

Low Oil Shutdown . . . . . . . . . . . . . . . . . . 17

Do Not Overload Generator . . . . . . . . . . . 17

Maintenance And Storage. . . . . . . . . . . . . . 18

Maintenance Schedule . . . . . . . . . . . . . 18

Engine Maintenance .. . . . . . . . . . . .. . . . 19

Change Engine Oil . . .. . . . . . . . . . . . . . 19

Air Filter Maintenance. . . . . . . . . . . . . .19

Spark Plug Maintenance. . . . . . . . . . . . 20

Cleaning Fuel Strainer . . . . . . . . . . . . 20

. . . 20

Generator Maintenance . . . . . . . . . . . . . . 21

Service and Storage . . . . . . . . . . . . . . . . . 22

Introduction

Inspect Muffler and Spark Arrester

. . . . . . . . . . . . . . . . . . . . .23

Parts Diagram and Parts List . . . . . . . . . . 24

Generator Parts Diagram . . . . . . . . . . . . 24

Engine Parts Diagram . . . . . . . . . .. . . . . 25

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . 26

Service Information . . . . . . . . . . . . . .. . . . . 28

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Trouble Shooting

Connecting to a Building’s Electrical

English Customer Service: 1-844-FIRMAN1

Thank you for purchasing a FIRMAN generator.

This manual covers operation and maintenance of the FIRMAN generators. All information in this

publication is based on the latest production information available at the time of approval for printing.

The manufacturer reserves the right to change, alter or other wise improve the generator and this

documentation at any time without prior change.

Page 01

This manual contains safety information to make you aware of the hazards and risks associated

with generator products and how to avoid them. This generator is designed and intended only

for supplying electrical power for operating compatible electrical lighting, appliances, tools and

motor loads, and is not intended for any other purpose. It is important that you read and

understand these instructions thoroughly before attempting to start or operate this equipment.

Save these original instructions for future reference.

Important Safety Information

The manufacturer cannot possibly anticipate every possible circumstance that might involve a

hazard. The warnings in this manual and the tags and decals affixed to the unit are therefore not

all-inclusive. If you use a procedure, work method or operating technique that the manufacturer

does not specifically recommend you must satisfy yourself that it is safe for you and others. You

must also make sure that the procedure work method or operating technique that you choose

does not render the generator unsafe.

SAFETY INFORMATION

DANGER WARNING CAUTION

DANGER indicates a

potentially hazardous

situation which, if not

avoided. WILL result in

death or serious injury.

WARNING indicates a

potentially hazardous

situation which, if not

avoided, could result in

death or serious injury.

CAUTION indicates a

potentially hazardous

situation which, if not

avoided, may result in minor

or moderate personal injury,

or property damage.

Toxic Fumes

Fire Hazard

Hot Surface.

Do Not Touch the Surface.

Kickback

Risk of Electric Shock

Explosion Hazard

Rotating Parts Entanglement

Hazard

Operator’s Manual

INTRODUCTION

English Customer Service: 1-844-FIRMAN1

SAFETY PRECAUTIONS

Page 02

WARNING

POISONOUS GAS HAZARD.

•

English Customer Service: 1-844-FIRMAN1

Page 03

CORRECT USAGE

Example location to reduce risk of carbon monoxide poisoning

•ONLY use outside and downwind, far away from windows, doors and vents.

•Direct exhaust away from occupied spaces.

INCORRECT USAGE

Do not operate in any of the following locations:

Near any door, window or vent

Garage

Basement

Crawl Space

Living Area

Attic

Entry Way

Porch

Mudroom

English Customer Service: 1-844-FIRMAN1

Page 04

WHEN OPERATING EQUIPMENT

DO NOT operate this product inside any

building, carport, porch, mobile equipment,

marine applications, or enclosure.

•

DO NOT tip engine or equipment at angle

which causes fuel to spill.

DO NOT stop engine by moving choke

control to “Start” position.

•

WHEN TRANSPORTING, MOVING

OR REPAIRING EQUIPMENT

Transport/move/repair with fuel tank

EMPTY or with fuel shutoff valve OFF.

•

•DO NOT tip engine or equipment at angle

which causes fuel to spill.

Disconnect spark plug wire.

•

WHEN STORING FUEL OR EQUIPMENT

WITH FUEL IN TANK

•Store away from furnaces, stoves, water

heaters, clothes dryers, or other appliances

that have pilot light or other ignition source

because they could ignite fuel vapors.

WARNING

This generator does not meet U. S. Coast

Guard Regulation 33CFR-183 and should not

be used on marine applications.

•

•Failure to use the appropriate U. S. Coast

Guard approved generator could result in

death or serious injury and/or property

damage.

WARNING

Generator voltage could cause

electrical shock or burn resulting

in death or serious injury.

•

WARNING

Starter cord kickback (rapid

retraction) will pull hand and arm

toward engine faster than you can

let go which could cause broken

bones, fractures, bruises, or

sprains resulting in serious injury.

When starting engine, pull cord slowly until

resistance is felt and then pull rapidly to

avoid kickback.

•

•NEVER start or stop engine with electrical

devices plugged in and turned on.

WARNING

Fuel and its vapors are extremely flammable

and explosive which could cause burns, fire,

or explosion resulting in death or serious

injury and/or property damage.

WHEN ADDING OR DRAINING FUEL

Turn generator engine OFF and let it cool at

least 2 minutes before removing fuel cap.

Loosen cap slowly to relieve pressure in tank.

Fill or drain fuel tank outdoors.

•

•DO NOT overfill tank. Allow space for fuel

expansion.

If fuel spills, wait until it evaporates before

starting engine.

•

Keep fuel away from sparks, open flames,

pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap, and fittings

frequently for cracks or leaks. Replace if

necessary.

DO NOT light a cigarette or smoke.

•

WHEN STARTING EQUIPMENT

Ensure spark plug, muffler, fuel cap, and air

cleaner are in place.

•

DO NOT crank engine with spark plug

removed.

•

Use approved transfer equipment, suitable

for the intended use, to prevent backfeed by

isolating generator from electric utility

workers.

English Customer Service: 1-844-FIRMAN1

Page 05

WARNING

Unintentional sparking

could cause fire or

electric shock resulting

in death or serious

injury.

WHEN ADJUSTING OR MAKING REPAIRS TO

YOUR GENERATOR

Disconnect the spark plug wire from the

spark plug and place the wire where it cannot

contact spark plug.

•

WHEN TESTING FOR ENGINE SPARK

Use approved spark plug tester.

•DO NOT check for spark with spark plug

removed.

•

WARNING

Starter and other rotating parts

could entangle hands, hair,

c lothi n g , o r a cces s o r i e s

resulting in serious injury.

NEVER operate generator without protective

housing or covers.

DO NOT wear loose clothing, jewelry or

anything that could be caught in the starter

or other rotating parts.

Tie up long hair and remove jewelry.

•

Excessively high operating speeds could result

in minor injury. Excessively low operating speeds

impose a heavy load.

DO NOT tamper with governor spring, links or

other parts to increase engine speed.

Generator supplies correct rated frequency

and voltage when running at governed speed.

DO NOT modify generator in any way.

•

DO NOT exceed the generator’s wattage

amperage capacity.

Start generator and let engine stabilize

before connecting electrical loads.

NOTE:

•

CAUTION

Exceeding generators wattage/amperage capacity

could damage generator and/or electrical devices

connected to it.

Connect electrical loads in OFF position,

then turn ON for operation.

Turn electrical loads OFF and disconnect

from generator before stopping generator.

•

DO NOT use generator with electrical cords

which are worn, frayed, bare or otherwise

damaged.

DO NOT operate generator in the rain or

wet weather.

DO NOT handle generator or electrical

cords while standing in water, while

barefoot, or while hands or feet are wet.

DO NOT allow unqualified persons or

children to operate or service generator.

•

WARNING

Exhaust heat/gases could ignite combustibles,

structures or damage fuel tank causing a fire,

resulting in death or serious injury and/or

property damage.

Contact with muffler area could cause burns

resulting in serious injury.

DO NOT touch hot parts and AVOID hot

exhaust gases.

Allow equipment to cool before touching.

It is a violation of California Public Resource

Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered,

or grass-covered land unless the exhaust

system is equipped with a spark arrester, as

defined in Section 4442, maintained in

effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer,

retailer, or dealer to obtain a spark arrester

designed for the exhaust system installed on

this engine.

Replacement parts must be the same and

installed in the same position as the original

parts.

•

When using generator for backup power,

notify utility company.

Use a ground fault circuit interrupter (GFCI)

in any damp or highly conductive area,

such as metal decking or steel work.

DO NOT touch bare wires or receptacles.

•

English Customer Service: 1-844-FIRMAN1

Page 06

•

Use generator only for intended uses.

If you have questions about intended use,

ask dealer or contact local service center.

Operate generator only on level surfaces.

DO NOT expose generator to excessive

moisture, dust, dirt, or corrosive vapors.

DO NOT insert any objects through cooling

slots.

If connected devices overheat, turn them off

and disconnect them from generator.

Shut off generator if:

-Electrical output is lost.

-Equipment sparks, smokes, or emits flames.

-Unit vibrates excessively.

•

WARNING

Medical and Life Support Uses.

In case of emergency, call 911 immediately.

NEVER use this product to power life support

devices or life support appliances.

NEVER use this product to power medical

devices or medical appliances.

Inform your electricity provider immediately

if you or anyone in your household depends

on electrical equipment to live.

Inform your electrical provider immediately

if a loss of power would cause you or anyone

in your household to experience a medical

emergency.

•

NOTE:

Improper treatment of generator could damage

it and shorten its life.

UNPACKING THE GENERATOR

Open carton and Remove packaging materials.

Remove generator, accessories boxes, and

literature from carton. If any items are missing

or damaged, contact our product service

department at 1-844-347-6261.

•

Parts Included

Your gasoline powered generator ships with

the following parts:

English Customer Service: 1-844-FIRMAN1

1. Engine Oil(Bottle) . . . . . . . . . . . . . . . . . . . . . . . 1

2. Oil Funnel . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . 1

3. Wrench for Spark plug . . . . . . . . . . . . . . . . . . . .1

5. Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

6. Quick Reference Guide . . . . . . . . . . . . . . . . . . . 1

4. Double Open wrench (10mm & 12mm). . . . 2

2

1

Quick

Reference

Guide

3

Manual

6

5

4

Page 07

REMOVAL OF SHIPPING SUPPORTS

Before you can run your new generator, follow

these simple instructions:

CAUTION

Failure to remove these items can result

in damage to your generator, possible

Personal injury and void your warranty.

Refer to the following instructions and pictures

to remove the attached engine support brackets

(red) under the engine.

3. You may discard these brackets, as they are no longer

required for normal operation of your generator.

Your generator is now ready for use. Refer to

your owner's manual for proper oil fill and

startup instructions.

Engine Support Brackets

(red color)

Remove these 2 nuts &

4 bolts as indicated.

Supplied wrenches

English Customer Service: 1-844-FIRMAN1

Page 08

CONTROLS AND FEATURES

Generator

*We are always working to improve our products. Therefore, the enclosed product may differ

slightly from the image on this page.

1

2①

②

③

④

⑤

⑥

⑦

⑧⑨

⑩

⑪

1- Fuel Gauge

2- 1.7 Gallon Capacity Fuel Tank

3- Fuel Cap

4- Choke Lever

5- Fuel Valve

6- Air Filter

7- 80cc FIRMAN OHV Engine

8- Recoil Starter

9- Oil Filler Cap

10- Outlet Cover

11- Control Panel

®

English Customer Service: 1-844-FIRMAN1

Page 09

Control Panel

Engine Switch – Flip the switch to the “ON”(l)

position and pull the recoil starter to start

the generator. Turn to the “OFF”(O) position

to turn off the generator.

1

2

3Circuit Breakers – The receptacles are

protected by an AC circuit protector. If the

generator is overloaded or an external short

circuit occurs. the circuit protector will trip.

If this occurs, disconnect all electrical loads

and try to determine the cause of the

problem before attempting to use the

generator again. If overloading causes the

circuit protector to trip, reduce the load.

Note: Continuous tripping of the circuit

protector may cause damage to generator

or equipment. The circuit protector may be

reset by pushing the button of the protector.

4

5

Ground Terminal – Consult an electrician

for local grounding regulations.

1

23

4

5

Total power drawn from all receptacles must not exceed the name plate rating.

NOTE:

Outlet Cover - Protect the receptacles from

dust and debris.

English Customer Service: 1-844-FIRMAN1

120V, 20A Duplex – (NEMA 5-20R) 20 Amp

of current may be drawn from this 120 Volt

receptacle.

Page 10

SPECIFICATIONS

AN IMPORTANT MESSAGE ABOUT TEMPERATURE:

Your Firman Power Equipment product is designed and rated for continuous operation at

ambient temperatures up to 40°C (104°F). When your product is needed, your product may be

operated at temperatures ranging from -15°C (5°F) to 50°C (122°F) for short periods. If the

product is exposed to temperatures outside this range during storage, it should be brought back

within this range before operation. In any event, the product must always be operated outdoors,

in a well-ventilated area and away from doors, windows and other vents.

When operated above 77°F(25°C) there may be a decrease in power.

Maximum wattage and current are subject to and limited by such factors as fuel BTU content

ambient temperature, altitude, engine condition and etc. Maximum power decreases about

3.5% for each 1,000 feet above sea level; and will also decrease about 1% for each 10°F(-12.2°C)

above 60°F(16°C) ambient temperature.

•

Model

Rated AC Voltage

Phase

Power Factor

Voltage regulator

Alternator Type

Running Watts

Starting Watts

Engine

Engine Type

Displacement

Low Oil Shutdown

Ignition System

Starting System

Fuel

Capacity Fuel Tank

Lubricating Oil Capacity

Carburetor Type

Air Cleaner

P.T.O. shaft rotation

120V

P01201

1200

Capacitor

Single Phase

1

Single Cylinder, 4-Stroke OHV Air Cooled

80 cc

Breakless Ignition Type, Flywheel Magneto

Unleaded Automotive Gasoline

Recoil

1.7 Gallon

12.9 oz(0.38L)

Counter Clockwise (Facing P.T.O.)

Float

Brushless

Polyurethane Type

YES

1500

FIRMAN

Rated Fequency 60Hz

Oil Type

See “Add Engine Oil” Section

English Customer Service: 1-844-FIRMAN1

Total Harmonic Distortion(THD) Standard

AC Grounding System

Neutral Bonded To Frame

Add Engine Oil

Page 11

DO NOT attempt to crank or start the engine

before it has been properly filled with the

recommended type and amount of oil. Damage

to the generator as a result of failure to follow

these instructions will void your warranty.

1.Place generator on a flat and level surface.

2.Clean area around oil fill and remove yellow

oil fill cap/dipstick.

3.Wipe dipstick clean.

NOTE:

The recommended oil type is 10W-30 automotive

oil. However outdoor temperatures will determine

the space proper oil viscosity for the engine. Use the

chart to select the best for the outdoor temperature

range expected.

The engine is equipped with a low oil shut-off and

will stop when the oil level in the crankcase falls

below the threshold level.

NOTE:

We consider the first 5 hours of run time to be

the break-in period for the unit. During the break

in period stay at or below 50% of the running

watt rating and vary the load occasionally to allow

stator windings to heat and cool. Adjusting the

load will also cause engine speed to vary and help

seat piston rings.

CAUTION

The unit is equipped with a low oil shutdown.If

the oil level becomes lower than required,the

sensor will activate a warning device or stop the

engine.

If generator shuts off and the oil level is within

specifications, check to see if generator is sitting

at an angle that forces oil to shift. Place on an

even surface to correct this. If engine fails to

start, the oil level may not be sufficient to

deactivate low oil level switch. Make sure the

sump is completely full of oil.

(H)

DRAIN PLUG

(L)

5.Replace oil fill cap/dipstick and fully tighten.

6.Oil level should be checked prior to each use

or at least every 8 hours of operation. Keep oil

level maintained.

4.Using oil funnel, slowly pour contents of

provided oil bottle into oil fill opening to the

"H" mark on dipstick. Be careful do not

overfill. Overfilling with oil could cause the

engine to not start or hard starting.

H

L

Low oil shutdown

Degrees Celsiusº(Outside)

Full Synthetic 5W-30

Degrees Fahrenheitº(Outside)

5W-30 10W-40

10W-30

CAUTION

English Customer Service: 1-844-FIRMAN1

Add Fuel

Page 12

Fuel must meet these requirements:

•Clean, fresh, unleaded gasoline.

Use regular UNLEADED gasoline with the

generator engine with a minimum 87 octane

/ 87 AKI (91 RON).

For high altitude use, see "Operation at High

Altitude".

Do not use gasoline with more than 10%

alcohol such as E85 or ethanol.

•

Failure to follow Operator's Manual for fuel

recommendations voids warranty.

Avoid generator damage.

DO NOT use unapproved gasoline such as E85.

DO NOT mix oil in gasoline.

DO NOT modify engine to run on alternate fuels.

•

WARNING

Fuel and its vapors are extremely flammable

and explosive which could cause burns, fire or

explosion resulting in death, serious injury

and/or property damage.

WHEN ADDING FUEL

Fill fuel tank outdoors.

DO NOT overfill tank. Allow space for fuel

expansion. If the tank is overfilled, fuel

can overflow onto a hot engine and cause fire

or explosion. Wipe up any spilled fuel

immediately.

If fuel spills, wait until it evaporates before

starting engine.

Keep fuel away from sparks, open flames,

pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap and fittings

frequently for cracks or leaks. Replace if

necessary.

DO NOT light a cigarette or smoke when

filling the fuel tank.

•

1.Clean area around fuel fill cap, remove cap.

2.Slowly add unleaded fuel to fuel tank. Be

careful not to fill above the red fuel level

indicator . This allows adequate space for

fuel expansion.

3.Install fuel cap and let any spilled fuel

evaporate before starting engine or wipe up

any spilled gasoline.

English Customer Service: 1-844-FIRMAN1

CAUTION

Slowly add unleaded gasoline to fuel tank.

Do not overfill tank.

Do not fill above the red line indicator.

This will allow expansion in hot weather

and prevent overflow.

•

Red Line Indicator

IMPORTANT: It is important to prevent gum

deposits from forming in fuel system parts such

as the carburetor, fuel hose or tank during storage.

Alcohol-blended fuels (called gasohol, ethanol

or methanol) can attract moisture, which leads to

separation and formation of acids during storage.

Acidic gas can damage the fuel system of an engine

while in storage. To avoid engine problems, the

fuel system should be emptied before storage of

30 days or longer. See the " Long Term Storage"

section. Never use engine or carburetor cleaner

products in the fuel tank as permanent damage

may occur.

Operation at High Altitude

At altitudes over 5,000 feet(1524 meters), a

minimum 85 octane / 85 AKI (89 RON) gasoline

is acceptable.

The density of air at high altitude is lower

than at sea level. Engine power is reduced

as the air mass and air-fuel ratio decrease.

Engine power and generator output will be

reduced approximately 3.5% for every 1000 feet

of elevation above sea level. This is a

natural trend and cannot be changed by

adjusting the engine. At high altitudes

Page 13

Altitude main jet 1

Altitude main jet 2

80cc

312715083

312715084

Altitude

3000-6000Feet

6000-8000Feet

English Customer Service: 1-844-FIRMAN1

OPEN

WARNING

Grounding

The National Electric Code requires your generator

must be properly connected to an appropriate

ground to help prevent electric shock.

Failure to properly ground the

generator can result in electric

shock.

WARNING

THERE IS A PERMANENT CONDUCTOR BETWEEN

THE GENERATOR (STATOR WINDING) AND THE

FRAME.

Use approved transfer equipment to prevent

backfeed by isolating generator from electric

utility workers.

When using generator for backup power, notify

utility company.

Use a ground fault circuit interrupter (GFCI) in

any damp or highly conductive area, such as

metal decking or steel work.

DO NOT touch bare wires or receptacles.

DO NOT use generator with electrical cords

which are worn,frayed, bare or otherwise

damaged.

DO NOT operate generator in the rain or wet

weather.

DO NOT handle generator or electrical cords

while standing in water, while barefoot, or

while hands or feet are wet.

DO NOT allow unqualified persons or children

to operate or service generator.

Connecting to a Building's Electrical System

WARNING

Generator voltage could cause

electrical shock or burn resulting

in death or serious injury.

•

The part number and recommended minimum

altitude for the application of the high

altitude carburetor main jet is listed in the

table below.

main jet and installation instructions can be

obtained by contacting Customer Support.

Installation instructions are also available in the

Technical Bulletin area of the FIRMAN internet site.

increased exhaust emissions can also result due to

the increased enrichment of the air fuel ratio.

Other high altitude issues can include hard

starting, increased fuel consumption and

spa r k pl u g fo uli n g. T o al l evi ate h igh

al titud e i ssues othe r t han the nat ural

power loss, FIRMAN can provide a high

altitude carburetor main jet. The alternative

OPERATION

Page 14

Generator Location

Make sure you review each warning in order to

prevent fire hazard.

Keep area clear of inflammables or other

hazardous materials.

Select a site that is dry, well ventilated and

protected from the weather.

Keep exhaust pipe clear of foreign objects.

Keep generator away from open flame.

Keep generator on a stable and level surface.

WARNING

Surge Protection

Voltage fluctuation may impair the proper

functioning of sensitive electronic equipment.

Electronic devices, including computers and

many programmable appliances use components

that are designed to operate within a narrow

voltage range and may be affected by momentary

voltage fluctuations. While there is no way to

prevent voltage fluctuations, you can take steps

to protect sensitive electronic equipment.

Install UL1449, CSA-listed, plug-in surge

suppressors on the outlets feeding your

sensitive equipment. Surge suppressors come

in single- or multi-outlet styles. They’re

desi g n ed t o p rote c t agai n s t v i r tual l y

all short-duration voltage fluctuations.

WARNING

POISONOUS GAS HAZARD.

Engine exhaust contains carbon

monoxide, a poisonous gas that

could kill you in minutes. You

CANNOT smell it, see it, or taste

it. Even if you do not smell exhaust

fumes, you could still be exposed

to carbon monoxide gas.

Operate this product ONLY outside far away

from windows, doors and vents to reduce

the risk of carbon monoxide gas from

accumulating and potentially being drawn

towards occupied spaces.

•

•Install battery-operated carbon monoxide

alarms or plug-in carbon monoxide alarms

with battery back-up according to the

manufacturer’s instructions. Smoke alarms

cannot detect carbon monoxide gas.

Avoid other generator hazards.

READ MANUAL BEFORE USE.

•

DO NOT run this product inside homes,

garages, basements, crawlspaces, sheds, or

other partially-enclosed spaces even if using

fans or opening doors and windows for

ventilation. Carbon monoxide can quickly

build up in these spaces and can linger for

hours, even after this product has shut off.

•ALWAYS place this product downwind and

point the engine exhaust away from

occupied spaces. If you start to feel sick,

dizzy, or weak while using this product, shut

it off and get to fresh air RIGHT AWAY. See a

doctor. You may have carbon monoxide

poisoning.

Do not block generator air vents with paper or

other material.

CAUTION

Tilting can cause fuel spillage.

CAUTION

English Customer Service: 1-844-FIRMAN1

Page 15

If engine starts after 3 pulls but fails to run, or if

unit shuts down during operation, make sure

unit is on a level surface and check for proper

oil level in crankcase. This unit may be equipped

with a low oil protection device. If so, oil must

be at proper level for engine to start.

Keep choke lever in “START” position for only 1

pull of the recoil starter. After first pull, move

choke lever to the “RUN” position for up to the

next 3 pulls of the recoil starter. Too much

choke leads to sparkplug fouling/engine

flooding due to the lack of incoming air. This

will cause the engine not to start.

Starting the Generator

1. Before starting the generator, check for loose

or missing parts and for any damage which

may have occurred during shipment.

2. Check oil level and fuel.

6. Move the choke lever to the “START” position.

5. Flip the engine switch to the “ON”(l) position.

8. Do not over-choke. As soon as engine starts

and warm up, move the choke lever to the

“RUN” position.

9. Allow generator to run at no load for few

minutes upon each initial start-up to permit

engine and generator to stablize.

Start er co rd kic kb ack(r ap id

retraction) will pull hand and arm

toward engine faster than you can

let go which could cause broken

bones, fractures, bruises, or sprains

resul tin g i n s eriou s i nju ry .

WARNING

When starting engine, pull cord slowly until

resistance is felt and then pull rapidly to avoid

kickback.

4. Turn the fuel valve to the “ON”(l) position.

7. Pull the starter cord slowly until resistance is

felt and then pull rapidly.

3. Disconnect all electrical loads from the

generator. Never start or stop the generator

with electrical devices plugged in or turned

on.

English Customer Service: 1-844-FIRMAN1

Page 16

Connecting Electrical Loads

1.Let engine stabilize and warm up for a few

minutes after starting.

2.Ensure circuit breaker on control panel is in

on position.

Connecting a generator to your electric utility

company’s power lines or to another power

source may be against the law. In addition this

action, if done incorrectly, could damage your

generator and appliances and could cause

serious injury or even death to you or a utility

worker who may be working on nearby power

lines. If you plan to run a portable electric

generator during an outage, please notify your

electric utility company immediately and

remember to plug your appliances directly into

the generator. Do not plug the generator into

any electric outlet in your home. Doing so could

create a connection to the utility company

power lines. You are responsible for ensuring

that your generator’s electricity does not feed

back into the electric utility power lines.

If the generator will be connected to a building

Stopping the Engine

1. Turn off and remove entire electrical loads.

Never start or stop the generator with

electrical devices plugged in or turned on.

This unit has been pretested and adjusted to

handle its full capacity. Before starting the

generator, disconnect all load. Apply load only

after generator is running. Voltage is regulated

via the engine speed adjusted at the factory for

correct output. Readjusting will void warranty.

CAUTION

When applying a load, do not exceed the maximum

wattage rating of the generator when using one or

more receptacles. Also, do not exceed the amperage

rating of any one receptacle.

Do not apply heavy electrical load during break-in

period (the first five hours of operations).

WARNING

Let the generator run at no-load for two

minutes to stabilize internal temperatures

of the engine and generator.

If a cover is used, do not install until unit has cooled.

Fuel and its vapors are extremely flammable and

explosive which could cause burns, fire or

explosion resulting in death, serious injury

and/or property damage.

electrical system, consult your local utility

company or a qualified electrician. Connections

must isolate generator power from utility

power and must comply with all applicable laws

and codes.

2. Press the engine switch to the “OFF”(O) position.

3. Turn the fuel valve to the “OFF”(O) position.

Do not leave the generator until it has

completely stopped.

3.Plug in and turn on the desired 120 or 240 Volt

AC, single phase, 60Hz electrical loads. It is

better to attach the item with largest load first.

English Customer Service: 1-844-FIRMAN1

Page 17

Do Not Overload Generator

DO NOT stop engine by moving choke control

to “START” position.

Important: Always ensure that the Fuel Valve

and the Engine Switch are in the “OFF” position

when the engine is not in use.

If the engine will not be used for a period of two

weeks or longer, please see the Storage section

for proper engine and fuel storage.

Low Oil Shutdown

If the engine oil drops below a preset level, an

oil switch will stop the engine. Check oil level

with dipstick.

If oil level is between LOW and HIGH mark on

dipstick:

1.DO NOT try to restart the engine.

2.Contact an Authorized FIRMAN Service Dealer.

3.DO NOT operate engine until oil level is

corrected.

If oil level is below LOW mark on dipstick:

1.Add oil to bring level to HIGH mark.

2.Restart engine and if the engine stops again

a low oil condition may still exist. DO NOT try

to restart the engine.

3.Contact an Authorized FIRMAN Service Dealer.

4.DO NOT operate engine until oil level is

corrected.

Overloading a generator in excess of its rated

wattage capacity can result in damage to the

generator and to connected electrical devices.

To prolong the life of your generator and

attached devices, follow these steps to add

electrical load:

1. Start the generator with no electrical load

attached.

2. Allow the engine to run for several minutes

to stabilize.

3. Plug in and turn on the first item. It is best to

attach the item with the largest load first.

4. Allow the engine to stabilize.

5. Plug in and turn on the next item.

6. Allow the engine to stabilize.

7. Repeat steps 5-6 for each additional item.

English Customer Service: 1-844-FIRMAN1

Page 18

English Customer Service: 1-844-FIRMAN1

MAINTENANCE AND STORAGE

MAINTENANCE SCHEDULE

General Recommendations

Regular maintenance will improve the performance and extend the life of the generator. See any

authorized dealer for service.

The generator's warranty does not cover items that have been subjected to operator abuse or

negligence. To receive full value from the warranty, the operator must maintain the generator as

instructed in this manual.

Some adjustments will need to be made periodically to properly maintain your generator.

All service and adjustments should be made at least once each season. Follow the requirements

in the Maintenanc Shedule chart above.

Notice Once a year you should clean or replace the spark plug and replace the air filter. New

spark plugs and clean air filter assure proper fuel-air mixture and help your engine run better

and last longer.

ITEM NOTES Daily(Before

operation)

Initial

25 hours

Every

50 hours

Every

100 hours

(or annual)

Fittings/

Fasteners

Spark Plug

Engine Oil

Air Filter

Fuel Line

Exhaust

System

Engine

Check condition. Adjust gap

and clean. Replace if necessary.

Check oil level.

Clean, replace if necessary.

Check for leakage. Retighten or

replace gasket if necessary.

Check adjust valve clearance.

Clean combustion chamber.

Check. Replace if necessary.

Check fuel hose for cracks or other

damage. Replace if necessary.

√

Replace.

Check spark arrester screen.

Clean/Replace if necessary.

Every

250 hours

√

To be performed by knowledgable/experienced owner or by authorized service center.

*

Fuel Filter Clean fuel filter and fuel tank

strainer. Replace if necessary. √

La page est en cours de chargement...

Firman P01201 Manuel utilisateur

Firman P01201 Manuel utilisateur

dans d''autres langues

Documents connexes