Yes ZVEE30DS Manuel utilisateur

WWW.ZEPHYRONLINE.COM

NOV20.0101

Airﬂow Control Technology

TM

C

Venezia

ZVE-E30DS, ZVE-E36DS, ZVE-E42DS

EN Use, Care, and Installation Guide

FR Guide d’utilisation, d’entretien et d’installation

2

Venezia Use, Care, and Installation Guide

VENEZIA

WALL

CORE

3

Venezia Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Contents

Page

Safety Information ............................................................................ 4-6

Types of Safety Warnings ................................................................... 4

General Safety ..................................................................................4-5

Operation ........................................................................................... 6

Electrical Requirements ...................................................................... 6

Federal Communication Commission Interface Statement ................. 6

List of Materials ................................................................................... 7

Installation Instructions .....................................................................8-17

Ducting Calculation Sheet .................................................................. 8

Mounting Height, Clearance, & Ducting ...........................................9-10

Ducting Options .................................................................................11

Hood Speciﬁcations ............................................................................12

Electrical Supply .................................................................................13

Cable Lock .........................................................................................13

Mounting the Hood .......................................................................... 14-15

Ductless Recirculation ..................................................................... 16-17

Features & Controls ..........................................................................18-24

Proximity Controls ...........................................................................18-20

Zephyr Connect ..............................................................................21-22

Optional RF Remote Control ............................................................23-24

Maintenance ................................................................................... 25-27

Hood & Filter Cleaning .....................................................................25-26

LumiLight LED ................................................................................... 27

ACT™ Conversion ............................................................................ 28-30

Airﬂow Control Technology (ACT™) ................................................... 28

Enabling ACT™ ................................................................................29-30

Wiring Diagram .................................................................................. 31

Troubleshooting............................................................................... 32-34

List of Parts & Accessories .................................................................. 35

Notes ..................................................................................................36

Limited Warranty ............................................................................... 37

Product Registration ...........................................................................38

4

Venezia Use, Care, and Installation Guide

VENEZIA

WALL

CORE

Safety Information

Your safety and the safety of others are very important.

We have provided many important safety messages in this

manual for your appliance. Always read and obey all safety

messages.

This is the Safety Alert Symbol. This symbol alerts you to

potential hazards that can cause severe bodily injury or death.

All safety messages will follow the Safety Alert Symbol and either

the words “DANGER” “WARNING” or “CAUTION”

DANGER

Danger means that failure to heed this safety statement may

result in severe injury or death.

READ AND SAVE THESE INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a) Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the manufacturer.

b) Before servicing or cleaning unit, switch power o at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

General Safety

WARNING

Warning means that failure to heed this safety statement

may result in extensive product damage, serious personal

injury, or death.

CAUTION

Caution means that failure to heed this safety statement

may result in minor or moderate personal injury, property or

equipment damage.

WARNING

To reduce the risk of ﬁre or electric shock, do not use this fan

with any solid-state control device.

WARNING

CAUTION

For General Ventilating Use Only. Do Not Use To Exhaust

Hazardous Or Explosive Materials And Vapors. Take care

when using cleaning agents or detergents. Suitable for use in

household cooking area.

WARNING

WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE

FIRE:

a) Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may ignite.

Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or

when ﬂambeing food. (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flambe’).

c) Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or ﬁlter.

d) Use proper pan size. Always use cookware appropriate for

the size of the surface element.

5

Venezia Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Safety Information

WARNING

READ AND SAVE THESE INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF INJURY TO PERSONS

IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING:

a) SMOTHER FLAMES with a close-ﬁtting lid, cookie sheet, or

metal tray, then turn o the burner. BE CAREFUL TO PREVENT

BURNS. If the ﬂames do not go out immediately, EVACUATE AND

CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN – You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels – a

violent steam explosion will result.

d) Use an extinguisher ONLY if:

1) You know you have a Class ABC extinguisher, and you

already know how to operate it.

2) The ﬁre is small and contained in the area where it

started.

3) The ﬁre department is being called.

4) You can ﬁght the ﬁre with your back to an exit

Based on “Kitchen Firesafety Tips” published by NFPA.

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

CAUTION

To reduce risk of ﬁre and to properly exhaust air outside, do

not vent exhaust air into spaces within walls, ceilings, attics,

crawl spaces, or garages.

WARNING

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by

qualiﬁed person(s) in accordance with all applicable codes and

standards, including ﬁre-rated construction.

b) Sucient air is needed for proper combustion and

exhausting of gases through the ﬂue (chimney) of fuel burning

equipment to prevent back drafting. Follow the heating

equipment manufacturer’s guideline and safety standards such

as those published by the National Fire Protection Association

(NFPA), and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE), and the local code

authorities.

c) When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

d) Ducted fans must always be vented to the outdoors.

e) If this unit is to be installed over a tub or shower, it must be

marked as appropriate for the application and be connected

to a GFCI (Ground Fault Circuit Interrupter) - protected branch

circuit.

WARNING

Prop. 65 Warning for California Residents: This product may

contain chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

6

Venezia Use, Care, and Installation Guide

VENEZIA

WALL

CORE

Safety Information

Operation

Ź Always leave safety grilles and ﬁlters in place. Without these components, operating blowers could catch onto hair, ﬁngers and

loose clothing.

Ź The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,

maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to negligence and

the warranty of the unit automatically expires due to improper maintenance.

NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

Electrical Requirements

Important:

Ź Observe all governing codes and ordinances.

Ź It is the customer’s responsibility to be aware of these below:

Ź To contact a qualiﬁed electrical installer.

Ź To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 latest

edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local codes

and ordinances.

Ź If codes permit and a separate ground wire is used, it is recommended that a qualiﬁed electrician determine that the ground path

is adequate.

Ź Do not ground to a gas pipe.

Ź Check with a qualiﬁed electrician if you are not sure the range hood is properly grounded.

Ź Do not have a fuse in the neutral or ground circuit.

Ź This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit protected

by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to Electrical Diagram

on product.

Ź A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase and

install appropriate connector if necessary.

* National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

Federal Communication Commission Interface Statement

Ź This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

Ź This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following

measures:

Ź Reorient or relocate the receiving antenna.

Ź Increase the separation between the equipment and receiver.

Ź Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

Ź Consult the dealer or an experienced radio/TV technician for help.

READ AND SAVE THESE INSTRUCTIONS

7

Venezia Use, Care, and Installation Guide

ZEPHYRONLINE.COM

List of Materials

Parts Not Supplied

Ducting, conduit and all installation tools

Cable locking connector (if required by local codes)

Duct cover extension accessory

Recirculating kit

RF remote control

Parts Supplied

Quantity Part

1Hood

2 Bae ﬁlters

2 LumiLight LED, 6W (pre-installed)

1 Duct cover assembly (top and bottom)

1 Duct cover wall bracket

1 8” round backdraft damper (pre-installed)

1 Hardware package

Wire Nuts (3)

M4 x 1-1/4” (3)

#6 x 1” (2)

M4 x 8” (2)

8

Venezia Use, Care, and Installation Guide

VENEZIA

WALL

CORE

Installation Instructions

Duct pieces

To t al

Equivalent number

length x used =

3- 1/ 4” x 10”

Rect.,

straight

1 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

5 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

90

0

elbow

20 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

90

0

15 Ft.

x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

45

0

9 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

straight

1 Ft. x ( ) =

Ft.

Subtotal column 1 =

Duct pieces

To t al

Equivalent number

length x used =

6”, 7”, 8”, 10”

Round, wall

cap with

damper

30 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round

roof cap

30 Ft. x ( ) =

Ft.

Subtotal column 2 =

Subtotal column 1 =

Total ductwork =

Maximum Duct Length: For satisfactory air movement,

the total duct length

should not exceed 150 equivalent feet.

6” round to

3- 1/ 4” x 10”

rect.

transition

1 Ft. x ( ) =

Ft.

6” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

16 Ft. x ( ) =

Ft.

7” round to

3 1/ 4” x 10”

rect.

transition

8 Ft. x ( ) =

Ft.

7” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

23 Ft. x ( ) =

Ft.

elbow

7” to 6” or

8” to 7” Round

tapered

reducer

25 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

elbow

15 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 45

0

elbow

9 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

ﬂat elbow

24 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect.

wall cap

with damper

30 Ft. x ( ) =

Ft.

Ft. x ( ) =

Ft.

15

6”, 7“, 8”

Round

in-line

damper

Ducting Calculation Sheet

9

Venezia Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Mounting Height, Clearance, & Ducting

24” min.

34” max.

min. A

min. B

max. C

min. D

min. E

max. F

Standard Extension

Hood Heights Duct Cover Duct Cover

minimum ducted (A) 27” 45“

minimum recirculating (B) 31-1/2” 49-1/2“

maximum (C) 44” 80”

Ceiling Heights

minimum ducted (D) 87” (7’ 3”) 105“ (8‘ 9”)

minimum recirculating (E)

91-1/2” (7’ 7-1/2”) 109-1/2“ (9‘ 1-1/2”)

maximum (F) 114” (9’ 6“ ) 150” (12’ 6”)

36”

10

Venezia Use, Care, and Installation Guide

VENEZIA

WALL

CORE

Installation Instructions

Mounting Height, Clearance, & Ducting

A minimum of 8” round duct is recommended to maintain maximum air ﬂow eciency.

Always use rigid type metal ducts only. Flexible ducts could restrict air ﬂow by up to 50%.

Also use the ducting calculation sheet (on page 11) to compute total available duct run when using

elbows, transitions and caps.

ALWAYS, when possible, reduce the number or transitions and turns. If long duct run is required,

increase duct size from 8” to 10”.

If turns or transitions are required; install as far away from hood duct output and as far apart,

between the two as possible.

Minimum mount height between range top to hood bottom should be no less than 24”.

Maximum mount height should be no higher than 34”.

It is important to install the hood at the proper mounting height. Hoods mounted too low could result

in heat damage and ﬁre hazard; while hoods mounted too high will be hard to reach and will lose its

performance and eciency.

If available, also refer range manufacturer’s height clearance requirements and recommended hood

mounting height above range. Always check your local codes for any dierences.

Duct cover extension kit available for ceiling heights up to 12 feet. Turn to the list of parts and

accessories section for part number and ordering information.

For shipment and installation damages:

Ź Please fully inspect unit for damage before installation.

Ź If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or

replacement.

Ź If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.

Ź If the unit is damaged by the installer (if other than the customer), repair of replacement must be

made by arrangement between customer and installer.

11

Venezia Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Ducting Options

Ź Use single wall rigid metal ductwork only.

Ź Fasten all connections with sheet metal screws and tape all joints w/ certiﬁed Silver Tape or Duct

Tape.

Fire Hazard: NEVER exhaust air or terminate ductwork into

spaces between walls, crawl spaces, ceilings, attics, or garages.

All exhaust must be ducted to the outside, unless using the

recirculating option.

WARNING

Sot or crawl space

roof pitch w/

ﬂashing & cap

side wall cap

w/ gravity

damper

ductless

recirculating

side wall cap

w/ gravity

damper

12

Venezia Use, Care, and Installation Guide

VENEZIA

WALL

CORE

Installation Instructions

Ů

Top of Hood

Side of HoodFront of Hood

7-3/4”

4-5/8”

5-1/4”

AC In

C/L

7/16”

14-5/16”

29-15/16”, 35-7/8”, 41-7/8”

6-13/16”

10-1/4”

STANDARD

min. ducted - 27”

min. recirc. - 31

-1/2”

max. - 44”

Z1C-01VE

min. ducted - 45”

min. recirc. - 49-

1/2”

max. - 80”

10-9/16”

24”

1-9/16”

13

Venezia Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

Electrical Supply

Electrical wiring must be done by qualiﬁed person(s) in

accordance with all applicable codes and standards. Turn o

electrical power at service entrance before wiring.

WARNING

For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not

use extension cord or adapter plug with this appliance.

Follow national electrical codes or prevailing local codes and ordinances.

This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly

grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring

must be 2 wire w/ ground. Please also refer to the Electrical Diagram labeled on product.

Cable Lock

A cable locking connector (not supplied) might be required by local codes. Check with local

requirements and codes, purchase and install appropriate connector if necessary. (FIG. A)

Cable Lock

1

FIG. A

14

Venezia Use, Care, and Installation Guide

VENEZIA

WALL

CORE

Installation Instructions

Mounting the Hood

At least two installers are required due to the

weight and size of the hood.

CAUTION

1. Measure from range top to hood bottom and

mark line A. (24” minimum from range top).

2. Plum and mark center line.

3. Mark mounting height line B. (10-1/4” from line

A)

4. Mark mounting spread from C/L on line B. From

center line to left mount mark (3-9/16”). From

center line to right mount mark (4-3/4”)

Wood blocking may need to be added behind

the drywall if no studs are present. Wall anchors

may also be used but check local codes for

compliance. Failure to use suitable wall anchors

and screws to hold the weight of the hood could

result in personal injury or damage to cooking

surface or counter.

WARNING

FIG. B

Duct Cover Bracket

A

B

C/L

10-1/4"

C/L

24" min

1

3-9/16"

4-3/4"

5. Fasten (2) M4 x 1-1/4” screws into studs on line B. Do not fasten screws all the way.

6. Hang hood onto screws and hand tighten. (FIG. B1) Use the last M4 x 1-1/4” screw to further

secure the hood to the wall from inside the hood.

7. Center and attach duct cover bracket to wall below ceiling or sot using (2) #6 x 1” screws.

8. Remove tape securing electronics mounting bracket to hood. Reposition electronics mounting

bracket to hood and secure by two pre-installed screws as shown in (FIG. A1).

9. Install electrical.

15

Venezia Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

10. Install duct work and duct tape.

11. Unwrap the blue antenna wire and position it behind the duct cover from step 13. There is no need

to secure it.

12. Power up hood and check for leaks around duct tape.

13. Place telescopic duct covers onto hood and extend inner (top) duct cover upwards and secure to

duct cover bracket using (2) M4 x 8” screws.

NOTE: If using hood in recirculating mode you must secure the air diverter plate onto wall before

installing duct work and duct covers. Turn to page 19 for more details.

Mounting the Hood

16

Venezia Use, Care, and Installation Guide

VENEZIA

WALL

CORE

Installation Instructions

Ductless Recirculation

Ductless recirculation is intended for applications where an exhaust duct work is not possible to be

installed. When converted, the hood functions as a recirculating hood rather than an exhaust hood.

Fumes and exhaust from cooking are drawn and ﬁltered by a set of optional charcoal ﬁlters. The air is

then puriﬁed and re-circulated back within the home.

We recommend to ALWAYS exhaust air outside of the home by employing existing or installing new

duct work, if possible. The hood is most eective and ecient as an exhaust hood. Only when the

exhaust option is not possible should you recourse to converting the hood into a recirculating hood.

When converted to be a recirculating hood, a set of charcoal ﬁlters are required on top of its standard

Metal Filter set. Order according to its part number below. The standard mesh ﬁlters are intended to

capture residue from cooking, and the optional charcoal ﬁlters help to purify fumes exhausted from

cooking for recirculation.

Recirculating Kit Installation (required if no ducting is used)

Kit includes the charcoal ﬁlters and the air diverter plate.

Hood Model Part Number Filters in Package

ZVE-E30DS ZRC-03VE 2

ZVE-E36DS ZRC-03VE 2

ZVE-E42DS ZRC-03VE 2

1. Purchase recirculating kit per the part number above.

2. Secure air diverter plate to wall below duct cover bracket. (FIG. C) Run 8” ducting from top of

hood and secure to air diverter plate. See manual included with recirculating kit for more detailed

instructions.

3. Remove bae ﬁlters from hood. Place the charcoal ﬁlters to the back side of the bae ﬁlters.

Secure the charcoal ﬁlters in place with rubber clips. (FIG. C).

4. Re-install bae ﬁlters.

17

Venezia Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Installation Instructions

5. Enable recirculating mode on the proximity

controls. (Refer details to pg. 20)

6. Charcoal ﬁlters must be replaced after every

200 hours of use (or approximately every 3 to 6

months based on the average of 1 - 2 hours of

daily cooking time). After 200 hours of use, the

notiﬁcation bell icon will display. When the bell

is tapped, the LCD display will cycle between

showing “REPLACE CHARCOAL FLTR” and

“HOLD UP TO RESET” every 2 seconds.

Charcoal Filter Replacements

Hood Model Part Number

Quantity to

Order

ZVE-E30DS Z0F-C005 2

ZVE-E36DS Z0F-C005 2

ZVE-E42DS Z0F-C005 2

DO NOT WASH CHARCOAL FILTERS. Charcoal

ﬁlters may need to be changed more often

depending on cooking habits.

Clip

FIG. C

18

Venezia Use, Care, and Installation Guide

VENEZIA

WALL

CORE

Features & Controls

Proximity Controls

Power Lights

Adjust 6 Speed Levels

Display & Icons

PROXIMITY SENSOR

Ź When approaching the hood while it is powered o, the Power, Fan Decrease, Fan Increase,

and Light icons will illuminate, and “HELLO” will appear on the LCD display for 2 seconds.

Ź If neither the fan nor lights are turned on within 60 seconds, the icons will turn o, and

“GOODBYE” will appear on the LCD display for 2 seconds.

Ź The icons will not disappear until the fan and lights are turned o.

CONTROL ICONS

Power

Ź Press the power icon to power on or o the fan and lights.

Ź The hood has a memory function to remember the last used settings for the fan and lights.

Ź After pressing the power icon to power o the hood, “GOODBYE” will appear on the LCD

display for 2 seconds.

Ź The 3s icon under the power icon only illuminates when the fan is powered on. It is an

indicator to enable Automatic Delay O by pressing and holding the power button

for 3 seconds.

Decrease Fan Speed

Ź Press the icon to decrease fan speed from 6, 5, 4, 3, 2, 1, o.

Increase Fan Speed

Ź Press the icon to increase fan speed from o, 1, 2, 3, 4, 5, 6.

Lights

Ź Press the lights icon to change lighting level from 1, 2, 3, o.

19

Venezia Use, Care, and Installation Guide

ZEPHYRONLINE.COM

Features & Controls

Proximity Controls

DISPLAY ICONS & FUNCTIONS

Ů

Ź The notiﬁcation bell icon will illuminate when an action needs to be taken. Tapping the

icon will cycle through the notiﬁcations. The notiﬁcation bell will remain illuminated until all

notiﬁcations are resolved. The notiﬁcation bell will not illuminate when the hood and controls

are powered o.

Bluetooth®

Ź The Bluetooth® icon will illuminate the device when connected with the hood via Bluetooth®.

The words “BLUETOOTH CONNECTED” or “BLUETOOTH DISCONNECT” will appear on the

LCD display whenever the connection changes.

Wi-Fi

Ź The Wi-Fi icon will illuminate when the hood is connected to the Wi-Fi. The words “WIFI

CONNECTED” or “WIFI DISCONNECTED” will appear on the LCD display whenever the

connection changes which will be managed via the Zephyr Connect app.

Ű

Ź While the fan is on, press and hold for 3 seconds to enable the delay o timer. The fan will

change to speed 1, the timer display will illuminate, the LCD display will show “AUTOMATIC

DELAY OFF”, and the timer will begin counting down from 10 minutes. After the timer reaches

0, the fan and lights will power o.

Ź The automatic delay o function timer begins at 10 minutes by default. The Zephyr Connect

app provides the options for either 5 or 10 minutes.

CleanAir

Ź When the fan is o, press and hold and simultaneously for 3 seconds to enable or

disable the CleanAir function. The LCD display will show “CLEAN AIR ENABLED” or “CLEAN

AIR DISABLED”.

Ź When enabled, the fan will turn on speed 1 every 4 hours for 10 minutes. While the fan is

running, the LCD display will show “CLEAN AIR ACTIVE” and the CleanAir icon will illuminate.

20

Venezia Use, Care, and Installation Guide

VENEZIA

WALL

CORE

Features & Controls

Proximity Controls

ĻŮ

Ź Airﬂow Control Technology (ACT™) allows the installer to set the maximum fan CFM to align

with local codes and regulations. When the fan is o, press and hold

for 3 seconds to

display ACT™ status.

Ź ACT 290 = 3 speeds, ACT 390 = 4 speeds, ACT 590 = 5 speeds.

Grease Filter Clean Reminder

Ź After 60 hours of fan use, the notiﬁcation bell icon will illuminate. When the bell is tapped,

the LCD display will cycle between showing “CLEAN GREASE FILTERS” and then “HOLD

DOWN TO RESET” every 2 seconds. If no action is taken for 30 seconds, the display turns o

and the notiﬁcation bell icon will remain illuminated.

Ź To hold down and reset, press and hold the fan decrease button for 3 seconds to

reset. The Zephyr Connect app provides the option to reset the reminder.

Recirculating Mode - Charcoal Filter Replacement Reminder

Ź Hold and for 3 seconds to enable or disable recirculating mode which will remind you

to replace the charcoal ﬁlter. The LCD display will show “RECIRCULATING ENABLED” to

enable and “RECIRCULATING DISABLE” to disable for 2 seconds.

Ź After 200 hours of fan use, the notiﬁcation bell icon will illuminate. When the bell is tapped,

the LCD display will cycle between showing “REPLACE CHARCOAL FLTR” and “HOLD UP TO

RESET” every 2 seconds. If no action is taken for 30 seconds, the display turns o and the

notiﬁcation bell will remain illuminated.

Ź To hold up and reset, press and hold the fan increase button for 3 seconds to reset.

The Zephyr Connect app provides the option to reset the reminder.

Remote Control Pairing Mode

Ź Hold for 3 seconds to enable remote control pairing mode. Once pairing mode is enabled,

the LCD display will illuminate “REMOTE PAIRING”. Press a button on the remote control to

synchronize it with the hood.

La page charge ...

Yes ZVEE30DS Manuel utilisateur

Yes ZVEE30DS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents