Spalding M661154 Manuel utilisateur

1

03/06 ID# M661154

Toll-Free Customer Service Number for U.S: 1-800-558-5234,

For Canada: 1-800-284-8339,

For Europe: 00 800 555 85234 (Sweden: 009 555 85234),

For Australia: 1-800-333 061

Internet Address: http://www.huffysports.com

REQUIRED TOOLS AND MATERIALS:

• 2 People

• Tape Measure

• Wood Board (scrap)

• Sawhorse or Support Table

• Hammer

• Step Ladder 8 ft. (2.4m)

• Safety Glasses

• (2 each) Wrenches

(2) Socket Wrenches and Sockets

• Extension

• Phillips-Head Screwdriver

1/2" 9/16" 3/4"

AND/OR

• Garden Hose or Sand

• Optional: Large & Small

Adjustable Wrenches

SAND

(300 lb.)

(136 kg)

1/2" 9/16" 3/4"

READ AND UNDERSTAND

OPERATOR'S MANUAL

BEFORE USING THIS UNIT.

FAILURE TO FOLLOW

OPERATING INSTRUCTIONS

COULD RESULT IN INJURY

OR DAMAGE TO

PROPERTY.

WARNING!

This manual, accompanied by sales receipt, should be saved and kept on hand as a convenient reference, as it

contains important information about your model.

Portable System

Owners Manual

Customer Service Center

• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.

Adult Assembly

Required.

Write Model Number

From Box Here:

2

ID# M661154 03/06

BEFORE YOU START!

To ensure optimal playability of backboard system, a close tolerance fit between the elevator

components and hardware is required. Test-fit large bolts into large holes of elevator tubes,

backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out

any excess paint from holes if necessary.

NOTE: Not all items pictured are included with every model.

03/06 ID# M661154

3

Owner must ensure that all players know and follow these rules

for safe operation of the system.

WARNING

•

DO NOT HANG on the rim or any part of the system including

backboard, support braces or net.

•

During play, especially when performing dunk type activities,

keep player's face away from the backboard, rim and net.

Serious injury could occur if teeth/face come in contact with

backboard, rim or net.

•

Do not slide, climb, shake or play on base and/or pole.

•

After assembly is complete, fill system completely with water

or sand. Never leave system in an upright position without

filling base with weight, as system may tip over causing

injuries.

•

When adjusting height or moving system, keep hands and

fingers away from moving parts.

•

Do not allow children to move or adjust system.

•

During play, do not wear jewelry (rings, watches, necklaces,

etc.). Objects may entangle in net.

•

Surface beneath the base must be smooth and free of gravel or

other sharp objects. Punctures cause leakage and could cause

system to tip over.

•

Keep organic material away from pole base. Grass, litter, etc.

could cause corrosion and/or deterioration.

•

Check pole system for signs of corrosion (rust, pitting,

chipping) and repaint with exterior enamel paint. If rust has

penetrated through the steel anywhere, replace pole

immediately.

•

Check system before each use for proper ballast, loose

hardware, excessive wear and signs of corrosion and repair

before use.

•

Check system before each use for instability.

•

Do not use system during windy and/or severe weather

conditions; system may tip over. Place system in the storage

position and/or in an area protected from the wind and free

from personal property and/or overhead wires.

•

Never play on damaged equipment.

•

When moving system, use caution to keep mechanism from

shifting.

•

Keep pole top covered with cap at all times.

•

Do not allow water in tank to freeze. During sub-freezing

weather add 2 gallons of non-toxic antifreeze, sand or empty

tank completely and store. (Do not use salt.)

•

While moving system, do not allow anyone to stand or sit on

base or have added ballasting on base.

•

Do not leave system unsupervised or play on system when

wheels are engaged for moving.

•

Use Caution when moving system across uneven surfaces.

System may tip over.

•

Use extreme caution if placing system on sloped surface.

System may tip over more easily.

•

See instruction manual for proper installation and

maintenance.

R

ea

d

a

nd

und

e

r

s

t

a

nd

w

a

r

ning

s

li

s

t

e

d

b

e

low

b

e

f

o

r

e

u

s

ing

t

hi

s

p

r

odu

c

t

.

F

a

ilu

r

e

t

o

f

ollow

t

h

ese

w

a

r

ning

s

m

ay

r

es

ul

t

in

se

r

iou

s

inju

r

y

a

nd

/

o

r

p

r

op

e

r

t

y

d

a

m

a

g

e

.

ID#: 561000 01/06

In the U.S.: 1-888-713-5488

In the U.S.: 1-800-558-5234

In Canada: 1-800-284-8339

In the U.S.: 1-800-334-9111

In the U.S.: 1-800-558-5234

In Canada: 1-800-284-8339

4

ID# M661154 03/06

2

1

3

TO ADJUST BACKBOARD:

1. While holding handle, remove pin.

2. Move elevator up or down to

desired height.

3. Replace pin full length to lock

system at desired height.

511679 05/05

1

2

4

3

MOVING SYSTEM

Adjust basketball backboard

height to lowest position.

While holding pole, rotate

basketball system forward

until wheels engage with

ground.

Move basketball system to

desired location.

Carefully rotate basketball

system upright.

1.

2.

3.

4.

5.

Check system for stability.

HEIGHT ADJUSTMENT

46

SAFETY INSTRUCTIONS

FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR

PROPERTY DAMAGE AND WILL VOID WARRANTY.

Owner must ensure that all players know and follow these rules for safe operation of the system.

To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check

entire box and inside all packing material for parts and/or additional instruction material. Before beginning

assembly, read the instructions and identify parts using the hardware identifier and parts list in this

document. Proper and complete assembly, use, and supervision are essential for proper operation and to

reduce the risk of accident or injury. A high probability of serious injury exists if this system is not installed,

maintained, and operated properly.

Most injuries are caused by misuse and/or not following instructions.

Use caution when using this system.

• If using a ladder during assembly, use extreme caution.

• Two (2) capable adults are recommended for this operation.

• Check base regularly for leakage. Slow leaks could cause system to tip over unexpectedly.

• Seat the pole sections properly (if applicable). Failure to do so could allow the pole

sections to separate during play and/or transport of the system.

• Climate, corrosion, or misuse could result in system failure.

• Minimum operational height is 6' 6" (1.98 m) to the bottom of backboard.

• This equipment is intended for home recreational use only and NOT excessive competitive

play.

• Read and understand the warning label affixed to pole.

• The life of your basketball pole depends on many conditions. The climate, placement of

the pole, location of the pole, exposure to corrosives such as pesticides, herbicides, or

salts are all important.

•

If technical assistance is required, contact Customer Service.

• Adult supervision is recommended when adjusting height.

03/06 ID# M661154

5

IMPORTANT!

Remove all contents from boxes.

Be sure to check inside pole sections;

hardware and additional parts are packed inside.

NOTICE TO ASSEMBLERS

Adult Assembly Required. Dispose of ALL packaging materials promptly.

ALL basketball systems, including those used for DISPLAYS, MUST be assembled and ballasted with

sand or water according to instructions. Failure to follow instructions could result in SERIOUS INJURY.

It is NOT acceptable to devise a makeshift weight system.

PRODUCT REGISTRATION:

Please remember to complete your product registration form on-line at:

www.huffysports.com/customer_support/product_registration.

WARNING: IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC

BACKBOARD, EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY

HAVE OCCURRED DURING SHIPMENT. CRACKS IN THE BACKBOARD

COULD RESULT IN SUDDEN BREAKAGE. IF BACKBOARD IS DAMAGED

IN ANY WAY PRIOR TO OR AFTER ASSEMBLY, CALL TOLL-FREE

NUMBER:

U.S. 1-800-558-5234; CANADA: 1-800-284-8339; http://www.huffysports.com

6

ID# M661154 03/06

Get to know the basic parts of your basketball system...

FRONT

PANEL

BACKBOARD

RIM

BASE

POLE

ELEVATOR

SYSTEM

03/06 ID# M661154

7

Item Qty. Part No. Description

1 1 266000 Base

2 2 905184 Strut, Pole to Base

3 1 905833 Exacta Height Assembly

4 1 FR908020 Top Pole Section

5 1 FR918019 Middle Pole Section

6 1 FR905179 Bottom Pole Section

7 2 108183 Wheel Bracket

8 2 266200 Wheel, 4 Inch

9 2 108182 Rod, Axle

10 1 203099 Nut, Ny-lock, 5/16-18

11 6 203063 Nylon Insert Lock Nut, 3/8-16

12 1 202662 Bolt, Hex Head, 5/16-18 x 4-1/2 Long

13 4 206938 Pushnut, 7/16 Shaft Diameter

14 7* 203100 Hex Flange Nut 5/16-18

15 1 204832 Bracket, Pole Mount

16 2 203053 Carriage Bolt, 5/16-18 x 4 Long

17 4 203232 Washer, Flat, 3/4” O.D.

18 4 204962 Bolt, Hex Head, 5/16-18 x .625 Long

19 2 206360 Bolt, Hex Head, 3/8-16 x 2-5/8 Long

20 2 204858 Spacer, Plastic Biscuit

21 2 204857 Spacer, Metal 1/2” O.D. x 1.44 Long

22 2 204859 Cover, Pin Slide

23 1 203038 Carriage Bolt, 5/16-18 x 2-3/4 Long

24 1 204850 Pin, Locking

25 1 204853 Lanyard, Black Coil

26 4 203527 Spacer, .530 I.D. x 1.5 Long

27 2 908256 Bracket, Backboard Support

28 1 266100 Cover, Front

29 6 206244 Bolt, Hex Head, 1/2-13 x 8 Long

30 4 201642 Spacer, Plastic, .530 I.D. x .625 Long

31 7 206340 Lock Nut, Hex 1/2-13

32 2 905820 Elevator Tube, Lower - Long

Item

Qty. Part No. Description

33 2 204838 Spring, Counter Balance

34 1 Rim

35 2 905808 Elevator Tube, Upper - Short

36 2 201682 Spacer, .530 I.D. x 1.875

37 2 908017 Plate, Triangle, (Black)

38 1 207103 Cap, Pole Top

39 2 200520 Screw, #8 x 3/4 Long

40 1 202605 Bolt, Hex, 1/2-13 x 4.25 Long

41 1 266300 Cap, Base

42 1 206990 Reinforcement Bracket

43 1 Net

44 4* 205528 Bolt, Hex Flange, 5/16-18 x 1 Long

45 4* 203309 Washer, Flat, 3/8

46 1 511679 Label, Height Adjustment and Moving

FR511679

47 6* 203738 Carriage Bolt, 5/16-18 x 1.75 Long

48 6* 200982 Nut, Locking, 5/16-18

49 1 108181 Plate, Pole Mouting

50 2 203331 Bolt, Hex Head, 3/8-16 x 1.5 Long

51 6 203218 Washer, Flat, 5/16

52 4 204961 Bolt, Hex Head, 3/8-16 x 0.625 Long

53 1 200516 Cover, Bolt End, Vinyl

54 1 900033 Bracket, Slam Jam

55 1 203796 Bolt, Tee, 3/8-16, 5” Long

56 1 200318 Bracket, Reinforcement, Slam Jam

57 1 203472 Spring, Rim

58 1 203795 Nut, Special, 3/8-16

59 1 203470 Washer, Flat, 1.5 O.D.

60 1 20157801 Board Pad, Left Section

61 1 20157901 Board Pad, Right Section

62 1 201580 Board Pad, Center Section

63 6 201596 Screw, 1/4 x 1.25

64 6 206303 Washer, Flat, 1/4

65 1 200503 Cover, Black OR

200504 Cover, Red

66 1 202795 Logo, NBA

* YOU MAY HAVE EXTRA PARTS WITH THIS MODEL.

PARTS LIST - See Hardware Identifier

NOTE

Hardware kit is designed for more than one

style of basketball system. Not all hardware

will be used.

8

ID# M661154 03/06

HARDWARE IDENTIFIER (BOLTS & SCREWS)

* You may have extra parts with this model.

#40 (1)

#39 (2)

Item #23 (1)*

#29 (6)

#16 (2)

#12 (1)

#44 (4)*

#19 (2)

#47 (6)*

#55 (1)

#63 (6)

#18 (4)

#52 (4)

#50 (2)

03/06 ID# M661154

9

HARDWARE IDENTIFIER (NUTS & WASHERS)

#14 (7)*

#10 (1)

#11 (6)

#31 (7)

#17 (4)

#45 (4)*

#58 (1)

#59 (1)

HARDWARE IDENTIFIER (STEEL SPACERS)

#51 (6)

#21 (2)

#64 (6)

#9 (2)

#48 (6)*

#66 (1)

10

ID# M661154 03/06

#54 (1)

#56 (1)

#57 (1)

HARDWARE IDENTIFIER (OTHER)

HARDWARE IDENTIFIER (PLASTIC SPACERS CAPS & CLIPS)

#13 (4)

#20 (2)

#26 (4)

#30 (4)

#53 (1)

#36 (2)

03/06 ID# M661154

11

TOOLS REQUIRED FOR THIS SECTION

SECTION A: ASSEMBLE THE BASE

And/Or:

This is what your system will look like when you’ve finished

this section.

1/2” 9/16”

Wrenches:

(1) 1/2” and (1) 9/16”

(2) Socket Wrenches

and Sockets

Extension

Phillips-Head

Screwdriver

12

ID# M661154 03/06

Check the following pre-assembled handle areas for tightness: Screw P/N 204803,

Nut P/N 203100, Carriage Bolts P/N 203103.

Carriage Bolt P/N 203103

Nut P/N 203100

Handle, Right

P/N 204856

Handle, Left

P/N 204855

Screw P/N 204803

Carriage Bolt P/N 203103

Height Adjustment Rod

P/N 904833

Label,Height

Indicator

P/N 204872

Label,Height

Indicator

P/N 204872

1.

3

03/06 ID# M661154

13

2.

Complete wheel assembly as shown in Figure A. Secure wheel bracket (7), wheel (8), axle (9), and push

nuts (13) to the tank (1) with a single bolt (18) and washer (51). Repeat procedure for opposite wheel.

7

8

9

13

18

1

Fig. A

Do not install both

bolts into the wheel

assembly at this time.

The front bolt will be

installed during strut

assembly in Step 8 of

this section

NOTE:

51

TO INSTALL SECOND

PUSHNUT:

• Assemble Pushnut,

Wheels, Axle, And Wheel

Bracket As Shown.

• Support Pushnut/Axle

From The End With A

Block Of Wood To Install

The Second Pushnut Onto

The Axle.

NOTE:

Wood Block

14

ID# M661154 03/06

6

5

4

4.

WOOD SCRAP

(NOT SUPPLIED)

5

4

While maintaining alignment, bounce middle pole section (5) into top section (4)

using a wood scrap as shown until the top pole no longer moves toward the pole

identification sticker on the middle pole.

Identification Sticker

Align dimple of top pole section (4)

into trough of middle pole section (5)

as shown.

IMPORTANT!

HOLE

DIMPLE

middle pole

THE IDENTIFICATION STICKER IS

LOCATED 5" FROM THE END OF

THE POLE. WHEN PROPERLY

POUNDED TOGETHER, THE POLE

SECTIONS SHOULD HAVE A 3-1/2"

MINIMUM OVERLAP, LEAVING 1-

1/2" BETWEEN THE OVERLAPPING

POLE AND THE IDENTIFICATION

STICKER.

CAUTION!

5"

middle pole

1-1/2"

3.

Identify pole sections.

ID

STICKER

03/06 ID# M661154

15

5.

4

5

6

WOOD SCRAP

(NOT SUPPLIED)

RODS SHOWN ARE

FOR VISUAL

REPRESENTATION

OF ALIGNMENT

AND ARE NOT

SUPPLIED WITH

THE HARDWARE

Align dimple of middle pole section (5)

into trough of bottom pole section (6)

as shown.

IMPORTANT!

HOLE

DIMPLE

Bottom pole

THE IDENTIFICATION STICKER IS

LOCATED 5" FROM THE END OF

THE POLE. WHEN PROPERLY

POUNDED TOGETHER, THE POLE

SECTIONS SHOULD HAVE A 3-1/2"

MINIMUM OVERLAP, LEAVING 1-1/2"

BETWEEN THE OVERLAPPING

POLE AND THE IDENTIFICATION

STICKER.

CAUTION!

5"

1-1/2"

ID

STICKER

Bottom pole

Bounce top and middle pole assembly (4 and 5) onto bottom pole section (6) using a

wood scrap as shown. Bounce until the top and middle pole assembly no longer

moves toward the pole identification mark on the bottom pole.

16

ID# M661154 03/06

12

53

10

51

6.

Attach pole assembly to base (1) as shown. Secure pole assembly to tank using bolts (50) and

pole mounting bracket (49) as shown.

7.

Secure tank struts (2) to pole as shown. Place cover (53) over exposed end of bolt

as shown.

6

49

6

1

2

TWO PEOPLE REQUIRED

FOR THIS PROCEDURE.

FAILURE TO FOLLOW

THIS WARNING COULD

RESULT IN SERIOUS

INJURY AND/OR

PROPERTY DAMAGE.

WARNING!

50

TWO PEOPLE REQUIRED

FOR THIS PROCEDURE.

FAILURE TO FOLLOW

THIS WARNING COULD

RESULT IN SERIOUS

INJURY AND/OR

PROPERTY DAMAGE.

WARNING!

DO NOT TIGHTEN

COMPLETELY

IMPORTANT!

50

03/06 ID# M661154

17

7

18

8.

Rotate non-secured ends of tank struts (2) outward to mounting holes in tank as

shown. Secure ends of tank struts (2) to wheel bracket (7), as shown. Repeat for

opposite side.

2

48

47

9.

Secure cover (28) to tank struts (2) using

bolts (47) and nuts (48) as shown.

28

TWO PEOPLE REQUIRED

FOR THIS PROCEDURE.

FAILURE TO FOLLOW

THIS WARNING COULD

RESULT IN SERIOUS

INJURY AND/OR

PROPERTY DAMAGE.

WARNING!

TIGHTEN ALL

COMPONENTS

COMPLETELY (STEPS 7-9)

IMPORTANT!

DO NOT TIGHTEN

COMPLETELY

IMPORTANT!

51

18

51

18

ID# M661154 03/06

10.

Install pole mount bracket (15) and reinforcement bracket (42) with carriage

bolts (16) as shown. Tighten flange nuts (14) completely.

4

42

16

15

14

11.

Attach spacers (20, 21) to pole mount bracket (15) with bolts (19), washers (17),

and nuts (11) as shown.

15

17

11

19

17

21

20

21

IMPORTANT!

Tighten just until

washers (17) stop

moving.

03/06 ID# M661154

19

Assemble lanyard (25) to locking pin (24) as shown (FIG A). Attach covers (22)

onto pole mount bracket (15) with carriage bolt (23) and nut (14) as shown.

12.

15

14

24

22

25

23

FIG. A

25

24

Loop end of pin

lanyard (25) over

carriage bolt (23)

as it passes

through the pole

mount bracket (15)

during this

assembly.

IMPORTANT!

23

25

24

Insert handle assembly through pole mount assembly as

shown. Lock pole assembly in place at the 10’ (3.05 m)

mark with pin (24).

24

13.

20

ID# M661154 03/06

TOOLS REQUIRED FOR THIS SECTION

SECTION B: ATTACH THE BACKBOARD

Phillips-Head

Screwdriver

This is what your system will look like when

you’ve finished this section.

Wrenches:

(2) 1/2", (2) 9/16”, and (2) 3/4”

(2) Socket Wrenches

and Sockets

And/Or

1/2” 9/16”

Extension

3/4”

Sawhorse

35

32

Upper Elevator tube

Lower Elevator tube

Identify

elevator tubes.

TOWARDS BOARD TOWARDS POLE

La page charge ...

Spalding M661154 Manuel utilisateur

Ce manuel convient également à

Spalding M661154 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents