AEG IKE64441XB Manuel utilisateur

AGG6438K

EN Hob User Manual 2

FR Table de cuisson Notice d'utilisation 23

DE Kochfeld Benutzerinformation 46

CONTENTS

Safety information 2

Safety instructions 4

Installation 7

Product description 12

Daily use 13

Hints and tips 16

Care and cleaning 17

Troubleshooting 18

Technical data 19

Energy efficiency 21

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully

read the supplied instructions. The manufacturer is not

responsible for any injuries or damages that are the result of

incorrect installation or usage. Always keep the instructions

in a safe and accessible location for future reference.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

the use of the appliance in a safe way and understand the

hazards involved.

• Do not let children play with the appliance.

• Keep all packaging away from children and dispose of it

appropriately.

• Keep children and pets away from the appliance when it

operates or when it cools down. Accessible parts are hot.

• If the appliance has a child safety device, it should be

activated.

• Children shall not carry out cleaning and user maintenance

of the appliance without supervision.

• Children aged 3 years and under must be kept away from

this appliance when it is in operation at all times.

2

General Safety

• WARNING: The appliance and its accessible parts

become hot during use. Care should be taken to avoid

touching heating elements.

• Do not operate the appliance by means of an external

timer or separate remote-control system.

• WARNING: Unattended cooking on a hob with fat or oil

can be dangerous and may result in fire.

• NEVER try to extinguish a fire with water, but switch off the

appliance and then cover flame e.g. with a lid or a fire

blanket.

• CAUTION: The cooking process has to be supervised. A

short term cooking process has to be supervised

continuously.

• WARNING: Danger of fire: Do not store items on the

cooking surfaces.

• Metallic objects such as knives, forks, spoons and lids

should not be placed on the hob surface since they can get

hot.

• Do not use a steam cleaner to clean the appliance.

• If the glass ceramic surface / glass surface is cracked,

switch off the appliance and unplug it from the mains. In

case the appliance is connected to the mains directly using

junction box, remove the fuse to disconnect the appliance

from power supply. In either case contact the Authorised

Service Centre.

• In case of hotplate glass breakage:

– shut immediately off all burners and any electrical

heating element and isolate the appliance from the

power supply,

– do not touch the appliance surface,

– do not use the appliance.

• If the supply cord is damaged, it must be replaced by the

manufacturer, an authorized Service or similarly qualified

persons in order to avoid a hazard.

3

• Where the appliance is directly connected to the power

supply, an all-pole isolating switch with a contact gap is

required. Complete disconnection in compliance with the

conditions specified in overvoltage category III must be

guaranteed. The earth cable is excluded from this.

• When you route the mains cable, make sure that the cable

doesn't come into direct contact (for example using

insulating sleeving) with parts that can reach temperatures

of more than 50°C above room temperature.

• WARNING: Use only hob guards designed by the

manufacturer of the cooking appliance or indicated by the

manufacturer of the appliance in the instructions for use as

suitable or hob guards incorporated in the appliance. The

use of inappropriate guards can cause accidents.

SAFETY INSTRUCTIONS

This appliance is suitable for the following

markets: FR

Installation

WARNING! Only a qualified

person must install this

appliance.

WARNING! Risk of injury or

damage to the appliance.

• Remove all the packaging.

• Do not install or use a damaged

appliance.

• Follow the installation instructions

supplied with the appliance.

• Keep the minimum distance from other

appliances and units.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Seal the cut surfaces with a sealant to

prevent moisture to cause swelling.

• Protect the bottom of the appliance

from steam and moisture.

• Do not install the appliance adjacent to

a door or under a window. This

prevents hot cookware falling from the

appliance when the door or the window

is opened.

• If the appliance is installed above

drawers make sure that the space,

between the bottom of the appliance

and the upper drawer, is sufficient for

air circulation.

• The bottom of the appliance can get

hot. Make sure to install a non-

combustible separation panel under the

appliance to prevent access to the

bottom.

Electrical Connection

WARNING! Risk of fire and

electric shock.

• All electrical connections should be

made by a qualified electrician.

• The appliance must be earthed.

• Before carrying out any operation make

sure that the appliance is disconnected

from the power supply.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Make sure the appliance is installed

correctly. Loose and incorrect electricity

4

mains cable or plug (if applicable) can

make the terminal become too hot.

• Use the correct electricity mains cable.

• Do not let the electricity mains cable

tangle.

• Make sure that a shock protection is

installed.

• Use the strain relief clamp on the cable.

• Make sure the mains cable or plug (if

applicable) does not touch the hot

appliance or hot cookware, when you

connect the appliance to the near

sockets.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug (if applicable) or to the

mains cable. Contact our Authorised

Service Centre or an electrician to

change a damaged mains cable.

• The shock protection of live and

insulated parts must be fastened in

such a way that it cannot be removed

without tools.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• If the mains socket is loose, do not

connect the mains plug.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• Use only correct isolation devices: line

protecting cut-outs, fuses (screw type

fuses removed from the holder), earth

leakage trips and contactors.

• The electrical installation must have an

isolation device which lets you

disconnect the appliance from the

mains at all poles. The isolation device

must have a contact opening width of

minimum 3 mm.

Gas connection

CAUTION! When using a gas

cylinder, always keep it on a

flat horizontal surface (with the

gas valve on top).

• All gas connections should be made by

a qualified person.

• Before installation, make sure that the

local distribution conditions (nature of

the gas and gas pressure) and the

adjustment of the appliance are

compatible.

• Make sure that there is air circulation

around the appliance.

• The information about the gas supply is

on the rating plate.

• This appliance is not connected to a

device, which evacuates the products

of combustion. Make sure to connect

the appliance according to current

installation regulations. Pay attention to

requirements regarding adequate

ventilation.

Use

WARNING! Risk of injury,

burns and electric shock.

• Remove all the packaging, labelling

and protective film (if applicable) before

first use.

• This appliance is for household use

only.

• Do not change the specification of this

appliance.

• Make sure that the ventilation openings

are not blocked.

• Do not let the appliance stay

unattended during operation.

• Set the cooking zone to “off” after each

use.

• Do not put cutlery or saucepan lids on

the cooking zones. They can become

hot.

• Do not operate the appliance with wet

hands or when it has contact with

water.

• Do not use the appliance as a work

surface or as a storage surface.

• When you place food into hot oil, it may

splash.

WARNING! Risk of fire and

explosion

• Fats and oil when heated can release

flammable vapours. Keep flames or

5

heated objects away from fats and oils

when you cook with them.

• The vapours that very hot oil releases

can cause spontaneous combustion.

• Used oil, that can contain food

remnants, can cause fire at a lower

temperature than oil used for the first

time.

• Do not put flammable products or items

that are wet with flammable products

in, near or on the appliance.

WARNING! Risk of damage to

the appliance.

• Do not keep hot cookware on the

control panel.

• Do not let cookware to boil dry.

• Be careful not to let objects or

cookware fall on the appliance. The

surface can be damaged.

• Do not activate the cooking zones with

empty cookware or without cookware.

• Do not put aluminium foil on the

appliance.

• Cookware made of cast iron, aluminium

or with a damaged bottom can cause

scratches on the glass / glass ceramic.

Always lift these objects up when you

have to move them on the cooking

surface.

• Use only stable cookware with the

correct shape and diameter larger than

the dimensions of the burners.

• Make sure cookware is centrally

positioned on the burners.

• Do not use large cookware that overlap

the edges of the appliance. This can

cause damage to the worktop surface.

• Make sure the flame does not go out

when you quickly turn the knob from

the maximum to the minimum position.

• Use only the accessories supplied with

the appliance.

• Do not install a flame diffuser on the

burner.

• The use of a gas cooking appliance

results in the production of heat and

moisture. Provide good ventilation in

the room where the appliance is

installed.

• Prolonged intensive use of the

appliance may call for additional

ventilation, for example opening of a

window, or more effective ventilation,

for example increasing the level of

mechanical ventilation where present.

• This appliance is for cooking purposes

only. It must not be used for other

purposes, for example room heating.

• Do not let acid liquids, for example

vinegar, lemon juice or limescale

remover, touch the hob. This can cause

matt patches.

• Discoloration of the enamel or stainless

steel has no effect on the performance

of the appliance.

Care and cleaning

WARNING! Do not remove the

buttons, knobs or gaskets from

the control panel. Water may

get inside the appliance and

cause damage.

• Clean the appliance regularly to

prevent the deterioration of the surface

material.

• Deactivate the appliance and let it cool

down before you clean it.

• Disconnect the appliance from the

electrical supply before maintenance.

• Do not use water spray and steam to

clean the appliance.

• Clean the appliance with a moist soft

cloth. Only use neutral detergents. Do

not use any abrasive products,

abrasive cleaning pads, solvents or

metal objects.

• Do not clean the burners in the

dishwasher.

Service

• To repair the appliance contact the

Authorised Service Centre. Use original

spare parts only.

• Concerning the lamp(s) inside this

product and spare part lamps sold

separately: These lamps are intended

to withstand extreme physical

conditions in household appliances,

such as temperature, vibration,

6

humidity, or are intended to signal

information about the operational status

of the appliance. They are not intended

to be used in other applications and are

not suitable for household room

illumination.

Disposal

WARNING! Risk of injury or

suffocation.

• Contact your municipal authority for

information on how to discard the

appliance correctly.

• Disconnect the appliance from the

mains supply.

• Cut off the mains electrical cable close

to the appliance and dispose of it.

• Flat the external gas pipes.

INSTALLATION

WARNING! Refer to Safety

chapters.

Before the installation

Before you install the hob, write down the

information bellow from the rating plate.

The rating plate is on the bottom of the

hob.

Model .......................................

PNC .........................................

Serial number ...........................

Gas Connection

WARNING! The following

instructions about installation,

connection and maintenance

must be carried out by qualified

personnel in compliance with

standards and local regulations

in force.

Choose fixed connections or use a flexible

pipe in stainless steel in compliance with

the regulation in force. If you use flexible

metallic pipes, be careful they do not

come in touch with mobile parts or they

are not squeezed. Also be careful when

the hob is put together with an oven.

Make sure that the gas supply

pressure of the appliance

obeys the recommended

values. The adjustable

connection is fixed to the

comprehensive ramp by means

of a threaded nut G 1/2". Screw

the parts without force, adjust

the connection in the

necessary direction and tighten

everything.

A B C

A. End of shaft with nut

B. Washer supplied with the appliance

C. Elbow supplied with the appliance

Rigid connection:

Carry out connection by using metal rigid

pipes (copper with mechanical end).

"Flexible" connection with mechanical

end:

• Natural gas: connection carry out with

a flexible pipe with mechanical end

which is screwed directly on the elbow

finishing the slope of the appliance.

• Butane/Propane: use a flexible tube,

equipped with it's collars if it is worth

visiting over all it's length and if the

7

appliance runs only on butane. If the

appliance runs on Propane, use a

flexible pipe with suitable metal end.

Flexible nonmetal pipes connection:

If it is possible to easily control the

connection in its full area, you can use a

flexible pipe. Tightly attach the flexible

pipe by clamps.

Liquid gas

Use the rubber pipe holder for liquid gas.

Always engage the gasket. Then continue

with the gas connection.

The flexible pipe is prepared for apply

when:

• it can not get hot more than room

temperature, higher than 30°C;

• it is no longer than 1500 mm;

• it shows no throttles;

• it is not subject to traction or torsion;

• it does not get in touch with cutting

edges or corners;

• it can be easily examined in order to

make sure its condition.

The control of preservation of the flexible

pipe consists in checking that:

• it does not show cracks, cuts, marks of

burnings on the two ends and on its full

length;

• the material is not hardened, but shows

its correct elasticity;

• the fastening clamps are not rusted;

• expired term is not due.

If one or more defects are visible, do not

repair the pipe, but replace it.

WARNING! When installation

is complete, make sure that the

seal of each pipe fitting is

correct. Use a soapy solution,

not a flame!

Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the

burner.

3. With a socket spanner 7 remove the

injectors and replace them with the

ones which are necessary for the type

of gas you use (see table in "Technical

Data" chapter).

4. Assemble the parts, follow the same

procedure backwards.

5. Replace the rating plate (it is near the

gas supply pipe) with the one for the

new type of gas supply. You can find

this plate in the package supplied with

the appliance.

If the supply gas pressure is changeable

or different from the necessary pressure,

you must fit an applicable pressure

adjuster on the gas supply pipe.

Adjustment of minimum level

WARNING! Information for

authorised installer only.

To adjust the minimum level of the

burners:

1. Light the burner.

2. Turn the knob on the minimum

position.

3. Remove the knob and using thin

screwdriver lift up and remove the

plastic magnet holder.

4. With a thin screwdriver, adjust the

bypass screw position (A).

8

A

5. If you change:

• from natural gas G20/G25 20/25

mbar to liquid gas, fully tighten the

bypass screw in.

• from liquid gas to natural gas

G20/G25 20/25 mbar, undo the

bypass screw approximately 1/4 of

a turn (1/2 of a turn for Multi Crown

burner).

• from natural gas G20/G25 20/25

mbar to town gas G130 8 mbar,

undo the bypass screw

approximately 3/4 of a turn (1/4 of a

turn for Multi Crown burner).

• from town gas G130 8 mbar to

natural gas G20/G25 20/25 mbar,

tighten the bypass screw

approximately 3/4 of a turn (1/4 of a

turn for Multi Crown burner).

• from liquid gas to town gas G130 8

mbar, undo the bypass screw

approximately 1 turn (1/2 of a turn

for Multi Crown burner).

• from town gas G130 8 mbar to

liquid gas, fully tighten the bypass

screw in.

6. Reassemble the magnet holder and

the knob.

WARNING! Make sure the

flame does not go out when

you quickly turn the knob from

the maximum position to the

minimum position.

Electrical connection

• Make sure that the rated voltage and

type of power on the rating plate agree

with the voltage and the power of the

local power supply.

• This appliance is supplied with a mains

cable. It has to be supplied with a

correct plug which can hold the load

that the rating plate rates. Make sure

that you install the plug in a correct

socket.

• Always use a correctly installed

shockproof socket.

• Make sure that there is an access to

the mains plug after the installation.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• There is a risk of fire when the

appliance is in connection with an

extension cable, an adapter or a

multiple connection. Make sure that the

ground connection agrees with the

standards and regulations.

• Do not let the power cable to heat up to

a temperature higher than 90° C.

9

Make sure that you connect the

blue neutral cable to the

terminal with a letter "N" on it.

Connect the brown (or black)

phase cable to the terminal

which has a letter "L". Keep the

phase cable connected at all

times.

If the pilot lights turn on after

connecting the hob to the

mains, turn on and off the

control knob and wait until the

residual heat indicator goes

out.

Connection cable

To replace the connection cable use only

the special cable or its equivalent. The

cable type is: H03V2V2-F T90.

Make sure that the cable section is

applicable to the voltage and the working

temperature. The yellow / green earth wire

must be approximately 2 cm longer than

the brown (or black) phase wire.

L

N

1. Connect the green and yellow (earth)

wire to the terminal which is marked

with the letter 'E', or the earth symbol

, or coloured green and yellow.

2. Connect the blue (neutral) wire to the

terminal which is marked with the letter

'N' or coloured blue.

3. Connect the brown (live) wire to the

terminal which is marked with the letter

'L'. It must always be connected to the

network phase.

Assembly

1.

2.

3.

min.

55 mm

min.

650 mm

560 mm

2

0

+

480 mm

2

0

+

min.

100 mm

30 mm

4.

10

5.

6.

B

A

A) supplied seal

B) supplied brackets

7.

CAUTION! Install the appliance

only on a worktop with flat

surface.

Installing hob under the hood

If you install the hob under a

hood, please see the

installation instructions of the

hood for the minimum distance

between the appliances.

Possibilities for insertion

The panel installed below the hob must be

easy to remove and let an easy access in

case a technical assistance intervention is

necessary.

Kitchen unit with door

min 20 mm

(max 150 mm)

30 mm

60 mm

B

A

A. Removable panel

B. Space for connections

Kitchen unit with oven

The electrical connection of the hob and

the oven must be installed separately for

safety reasons and to let easy remove

oven from the unit.

11

PRODUCT DESCRIPTION

Cooking surface layout

3

4

6

5

2

1

Semi-rapid burner

2

Multi Crown burner

3

Auxiliary burner

4

Control panel

5

Control knobs

6

Window for Hob²Hood infrared signal

Control panel layout

1

4

2 3

Use the sensor fields to operate the Minute Minder and Hob²Hood. The displays,

indicators and sounds tell which functions operate.

Sen‐

sor

field

Function Comment

1

Hob²Hood To activate and deactivate the manual mode

of the function.

2

- Timer display To show the time in minutes.

3

/

- To increase or decrease the time.

4

- To select the Timer function.

12

Control knob

Symbol Description

no gas supply / off posi‐

tion

ignition position / maxi‐

mum gas supply

minimum gas supply

Residual heat

$

A. Residual heat indicator.

WARNING! There is a risk of

burns from residual heat.

The residual heat indicator

lights up when you turn off the

burner.

Knob of the burner

Time of cooking (min)

on < 5 on > 5

Multi Crown off after 25 off after 25

Semi-rapid off after 10 off after 20

Auxiliary off after 5 off after 15

DAILY USE

WARNING! Refer to Safety

chapters.

13

Burner overview

$

%

'

&

$

%

'

&

A. Burner cap

B. Burner crown

C. Ignition candle

D. Thermocouple

Ignition of the burner

Always light the burner before

you put on the cookware.

WARNING! Be very careful

when you use open fire in the

kitchen environment. The

manufacturer declines any

responsibility in case of the

flame misuse.

1. Push the control knob down and turn it

counterclockwise to the maximum gas

supply position ( ).

2. Keep the control knob pushed for

equal or less than 10 seconds. This

lets the thermocouple warm up. If not,

the gas supply is interrupted.

3. Adjust the flame after it is regular.

If after some tries the burner

does not light, check if the

crown and its cap are in correct

positions.

WARNING! Do not keep the

control knob pushed for more

than 15 seconds. If the burner

does not light after 15 seconds,

release the control knob, turn it

into off position and try to light

the burner again after minimum

1 minute.

CAUTION! In the absence of

electricity you can ignite the

burner without electrical device;

in this case approach the

burner with a flame, turn the

control knob counter-clockwise

to maximum gas supply

position and push it down.

Keep the control knob pushed

for equal or less than 10

seconds to let the

thermocouple warm up.

If the burner accidentally goes

out, turn the control knob to the

off position and try to light the

burner again after minimum 1

minute.

The spark generator can start

automatically when you switch

on the mains, after installation

or a power cut. It is normal.

Each control knob has a pilot

light. It lights up when you turn

the control knob.

14

The hob is supplied with the

progressive valves. They make

the flame regulation more

precise.

WARNING! If you do not

switch the knob to the off

position, after two hours a

warning sound is emitted and

the symbols flash red. It

reminds you that the burner is

on. To stop the sound, touch

, , or .

Turning the burner off

To put the flame out, turn the knob to the

off position .

WARNING! Always turn the

flame down or switch it off

before you remove the pans

from the burner.

Minute Minder

You can use this function as a Minute

Minder.

1. Touch .

To activate the function.

2. Touch or of the timer to set the

time (00 - 99 minutes).

When the time comes to an end, the

sound operates and 00 flashes.

In the last minute the time

decreases in seconds, and the

last 10 seconds the timer emits

a sound signal.

3. Touch , , or .

To stop the sound.

4. To stop the timer, touch longer .

You can use the Minute Minder

at any time also if the appliance

is off.

The function has no effect on

the operation of the burners.

Hob²Hood

It is a manual function which connects the

hob to a special hood. Both the hob and

the hood have an infrared signal

communicator. Speed of the fan is defined

manually from the hob.

For most of the hoods, the

remote system is originally

deactivated. Activate it before

you use the function. For more

information refer to the hood

user manual.

Manual modes:

Mode Manual

light

Fan speed

H0 Off Off

HL On Off

H1 On Level 1

H2 On Level 2

H3 On Level 3

Touch to set the speed

manually.

Touch longer to turn off the

fan and the light.

WARNING! After end of

cooking, the hood does not turn

off automatically. Turn it off

manually.

15

HINTS AND TIPS

WARNING! Refer to Safety

chapters.

Cookware

CAUTION! Do not use cast

iron pans, clay or earthenware

pots, grill or toaster plates.

WARNING! Do not put the

same pan on two burners.

WARNING! Do not put

unstable or damaged pots on

the burner to prevent spills and

injuries.

CAUTION! Make sure that the

bottoms of pots do not stand

too close to the control knob,

otherwise the flame heats the

control knob up.

CAUTION! Make sure that pot

handles are not above the front

edge of the cooktop.

CAUTION! Make sure that the

pots are placed centrally on the

burner in order to get the

maximum stability and a lower

gas consumption.

CAUTION! Liquids spilt during

cooking can cause the glass to

break.

Diameters of cookware

Use cookware with diameters

applicable to the size of

burners.

Burner Diameter of

cookware

(mm)

Multi Crown 180 - 260

Semi-rapid 120 - 220

Burner Diameter of

cookware

(mm)

Auxiliary 80 - 180

Hints and Tips for Hob²Hood

When you operate the hob with the

function:

• Protect the hood panel from direct

sunlight.

• Do not spot halogen light on the hood

panel.

• Do not cover the hob control panel.

• Do not interrupt the signal between the

hob and the hood (for example with a

hand or a cookware handle). See the

picture.

The hood in the picture is only

exemplary.

Keep the window for Hob²Hood

infrared signal communicator

clean.

Other remotely controlled

appliances may block the

signal. Do not use any remotely

controlled appliances at the

time when you use the function

on the hob.

16

Cooker hoods with the Hob²Hood

function

To find the full range of cooker hoods

which work with this function refer to our

consumer website.

CARE AND CLEANING

WARNING! Refer to Safety

chapters.

General information

• Clean the hob after each use.

• Always use cookware with a clean

base.

• Scratches or dark stains on the surface

have no effect on how the hob

operates.

• Use a special cleaner suitable for the

surface of the hob.

The presence of water or other

liquids on the control panel can

accidentally activate or

deactivate the hob functions.

WARNING! Do not use knives,

scrapers or similar instruments

to clean the surface of the

glass or the rims of the burners

and the frame (if applicable).

• Wash stainless steel parts with water,

and then dry them with a soft cloth.

Pan supports

The pan supports are not

resistant to washing in a

dishwasher. They must be

washed by hand.

1. Remove the pan supports to easily

clean the hob.

Be very careful when you

replace the pan supports to

prevent the hob top from

damage.

2. The enamel coating occasionally can

have rough edges, so be careful when

you wash the pan supports by hand

and dry them. If necessary, remove

stubborn stains with a paste cleaner.

3. After you clean the pan supports,

make sure that they are in correct

positions.

4. For the burner to operate correctly,

make sure that the arms of the pan

supports are inserted in the recesses

of the enamelled plates.

Removing and assembling pan

supports

After cleaning of the hob, make sure that

pan supports are in a correct position. In

order to place a pan support properly.

Cleaning the hob

• Remove immediately: melted plastic,

plastic foil, sugar and food with sugar,

otherwise, the dirt can cause damage

to the hob. Take care to avoid burns.

• Remove when the hob is sufficiently

cool: limescale rings, water rings, fat

stains, shiny metallic discoloration.

Clean the hob with a moist cloth and a

non-abrasive detergent. After cleaning,

wipe the hob dry with a soft cloth.

• To clean the enamelled parts, caps and

crowns, wash them with warm soapy

water and dry them carefully before you

put them back on.

Cleaning the spark plug

This feature is obtained through a ceramic

ignition candle with a metal electrode.

Keep these components well clean to

17

prevent difficult lighting and check that the

burner crown holes are not obstructed.

Periodic maintenance

Speak to your local Authorised Service

Centre periodically to check the conditions

of the gas supply pipe and the pressure

adjuster, if fitted.

TROUBLESHOOTING

WARNING! Refer to Safety

chapters.

What to do if...

Problem Possible cause Remedy

There is no spark when you

try to activate the spark gen‐

erator.

The hob is not connected to

an electrical supply or it is

connected incorrectly.

Check if the hob is correctly

connected to the electrical

supply.

The fuse is blown. Make sure that the fuse is

the cause of the malfunc‐

tion. If the fuse is blown

again and again, contact a

qualified electrician.

Burner cap and crown are

placed incorrectly.

Place the burner cap and

crown correctly.

The flame extinguishes im‐

mediately after ignition.

Thermocouple is not heated

up sufficiently.

After lightning the flame,

keep the knob pushed for

equal or less than 10 sec‐

onds.

The flame ring is uneven. Burner crown is blocked with

food residues.

Make sure that the injector

is not blocked and the burn‐

er crown is clean.

The control panel brightness

is reduced or it switches off.

The temperature of the plate

is high. To ensure long life‐

time of the display the

brightness is reduced de‐

pending on the temperature

of the hob. Above a certain

temperature the control pan‐

el switches off.

Let the hob cool down.

The control knob pilot lights

turn on after connecting the

hob to the mains or after a

power outage.

Pilot light test. Refer to "Installation".

18

Problem Possible cause Remedy

Hob²Hood function does not

work.

You covered the control

panel.

Remove the object from the

control panel.

You cannot activate or oper‐

ate Hob²Hood and Minute

Minder.

There is water or fat stains

on the control panel.

Clean the control panel.

If you cannot find a solution...

If you cannot find a solution to the problem

yourself, contact your dealer or an

Authorised Service Centre. Give the data

from the rating plate. Make sure, you

operated the hob correctly. If not the

servicing by a service technician or dealer

will not be free of charge, also during the

warranty period. The instructions about

the Service Centre and conditions of

guarantee are in the guarantee booklet.

Labels supplied with the

accessories bag

Stick the adhesive labels as indicated

below:

MOD.

PROD.NO.

SER.NO

DATA

MOD.

PROD.NO.

SER.NO

DATA

MOD.

PROD.NO.

SER.NO.

03 IT

MADE IN ITALY

TYPE

IP20

0049

A B C

A. Stick it on Guarantee Card and send

this part (if applicable).

B. Stick it on Guarantee Card and keep

this part (if applicable).

C. Stick it on instruction booklet.

TECHNICAL DATA

Hob dimensions

Width 590 mm

Depth 520 mm

19

Bypass diameters

BURNER Ø BYPASS 1/100 mm

Multi Crown 57

Semi-rapid 35

Auxiliary 28

Other technical data

TOTAL POW‐

ER:

Gas origi‐

nal:

G20/G25 (2E+) 20/25 mbar 8,9 kW

Gas re‐

placement:

G30 (3+) 28-30 mbar 607 g/h

G31 (3+) 37 mbar 596 g/h

G130 (1c) 8 mbar 8,7 kW

Electric sup‐

ply:

220-240 V ~ 50-60 Hz

Appliance cat‐

egory:

III1c2E+3+

Gas connec‐

tion:

G 1/2"

Appliance

class:

3

Gas burners for NATURAL GAS G20/G25 20/25 mbar

BURNER NORMAL POWER

kW

MINIMUM POWER

kW

INJECTOR MARK

Multi Crown 3,9 1,4 146

Semi-rapid 2,0 0,6 96x

Auxiliary 1,0 0,33 70

Gas burners for LPG G30/G31 28-30/37 mbar

BURNER NORMAL

POWER

kW

MINIMUM

POWER

kW

INJECTOR

MARK

NOMINAL GAS FLOW g/h

G30 28-30

mbar

G31 37 mbar

Multi

Crown

3,55 1,4 095 258 254

Semi-rapid 1,9 0,6 71 138 136

Auxiliary 1,0 0,33 50 73 71

20

La page charge ...

AEG IKE64441XB Manuel utilisateur

AEG IKE64441XB Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents