Extron WBA 100 Guide d'installation

Extron
Marque
Extron
Modèle
WBA 100
Catégorie
Accessoires de rack
Taper
Guide d'installation
WBA 100 Adapter Plate
•
Setup Guide
The WBA 100 is an adapter plate that secures to a Chief
®
PAC526 in-wall box or directly to a at surface. The adapter plate holds
up to four Extron ZipClip 200 mounting clips, or one half-rack product, or a combination of quarter- and eighth-rack products.
Mounting ZipClip 200 Products to the Adapter Plate
Up to four ZipClip 200 mounting clips (not included) can be mounted on the WBA 100, using the designated ZipClip holes on the
adapter plate (see the image below). To mount the ZipClip:
ATTENTION:
• Some products have hexagonal holes in their base, which anchor standoffs for
internal circuit boards (see the image at right). Using these holes will damage the
product and will not provide secure mounting.
• Certains produits possèdent des ouvertures hexagonales à leur base, qui xent des
entretoises pour des cartes de circuit internes (voir l’image de droite). L’utilisation
de ces ouvertures endommagera le produit et n’offrira pas de montage sécurisé.
#4-40 Thread for
Rack Mounting
Hexagonal holes
for circuit board
standoffs
(do not use)
Mounting Products to the Adapter Plate
The various mounting holes on the WBA 100 can accommodate a combination of half-, quarter-, and eighth-rack width products,
up to 9.5 inches deep. To mount a product:
ZipClip 200 (4)
WBA 100
Align the holes on the ZipClip
with the designated holes on the
adapter plate.
1
Secure the ZipClip with
the included mounting
screws and washers.
2
(2) #10-24 x 5/16" screws
(2) #10 washers
Secure the provided mounting screws
from behind the adapter plate.
3
Remove any rubber feet
attached to the device.
1
2
Place the device at the edge
of the adapter plate and align
the mounting holes.
Use the two mounting holes on
diagonally opposite corners of the
device (see the ATTENTION below
for important information).
(2) #4-40 x 3/16" screws
Sec
f
ro
m
(
2
)
#4
-
Mount additional products as necessary.
4
68-2867-50
Rev. A
11 15
© 2015 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Mounting the Adapter Plate in a Chief Wall Box
Mount the adapter plate in the Chief wall box as shown below.
Mounting the Adapter Plate on a Wall
The WBA 100 can be mounted on a wall using the two
keyholes and two slots for a removable installation, or
the four clearance holes for a xed installation.
The keyhole and slot at the center of the plate can be
used for securing the plate to a wall stud.
Mount the adapter plate on the wall using four #10
screws (not included).
Wall
#10 screws
(not provided)
Keyhole
Clearance
hole
Slot
Clearance
hole
Attach a ground wire using the grounding
screw inside the wall box as shown.
1
Wall Box
(Bottom View)
Mount the assembled
WBA 100 adapter plate to
the Chief wall box using the
provided mounting screws
and washers.
2
(2) #10-24 x 5/16" screws
(2) #10 washers
Wall Box (Inside View)
Inside the wall box, attach the
ground wire to the grounding stud
on the WBA 100 as shown below.
3
Grounding Stud
Ground Wire
Wall Box
(T
op View)
  • Page 1 1
  • Page 2 2

Extron WBA 100 Guide d'installation

Extron
Marque
Extron
Modèle
WBA 100
Catégorie
Accessoires de rack
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents