HP Photosmart C4200 All-in-One Printer series Mode d'emploi

Marque: HP

Modèle: Photosmart C4200 All-in-One Printer series

Taper: Mode d'emploi

Basics Guide

Guide d'utilisation

HP Photosmart C4200 All-in-One series

Hewlett-Packard Company notices

The information contained in this document is subject to change without notice.

as allowed under copyright laws. The only warranties for HP products and services are set forth in the express warranty statements accompanying

such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial

errors or omissions contained herein.

Windows, Windows 2000, and Windows XP are U.S. registered trademarks of Microsoft Corporation.

Windows Vista is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.

Intel and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.

Avis publiés par la société Hewlett-Packard

Les informations contenues dans ce document peuvent faire l'objet de modifications sans préavis.

dans les cas permis par la législation relative aux droits d'auteur. Les seules garanties relatives aux produits et services HP sont décrites dans les

déclarations de garantie expresse accompagnant lesdits produits et services. Aucun élément de ce document ne constitue une garantie

supplémentaire. Hewlett-Packard ne saurait être tenu pour responsable des erreurs ou omissions techniques ou rédactionnelles de ce document.

Windows, Windows 2000 et Windows XP sont des marques déposées de Microsoft Corporation aux Etats-Unis.

Windows Vista est une marque déposée ou une marque de Microsoft Corporation aux Etats-Unis et/ou dans d'autres pays.

Intel et Pentium sont des marques ou des marques déposées d'Intel Corporation ou de ses filiales aux Etats-Unis et dans d'autres pays.

HP Photosmart C4200 All-in-

Basics Guide

English

One

series

Contents

1 HP All-in-One overview

The HP All-in-One at a glance....................................................................................................5

Control panel buttons.................................................................................................................6

Find more information.................................................................................................................7

Load originals and load paper....................................................................................................7

Avoid paper jams........................................................................................................................8

Make a copy...............................................................................................................................9

Scan an image............................................................................................................................9

Print 10 x 15 cm (4 x 6 inch) photos...........................................................................................9

Replace the print cartridges......................................................................................................10

Clean the HP All-in-One...........................................................................................................13

Clean the glass...................................................................................................................13

Clean the lid backing..........................................................................................................13

2 Troubleshooting and support

Uninstall and reinstall the software...........................................................................................15

Hardware setup troubleshooting...............................................................................................15

Clear paper jams......................................................................................................................18

Print cartridge troubleshooting..................................................................................................19

Support process.......................................................................................................................19

3 Technical information

System requirements................................................................................................................20

Product specifications...............................................................................................................20

Print cartridge yield...................................................................................................................20

Regulatory notices....................................................................................................................20

Warranty...................................................................................................................................22

4 HP Photosmart C4200 All-in-One series

English

1 HP All-in-One overview

Use the HP All-in-One to quickly and easily accomplish tasks such as making a copy,

scanning documents, or printing photos from a memory card. You can access many

HP All-in-One functions directly from the control panel, without turning on your computer.

NOTE: This guide introduces basic operations and troubleshooting, as well as

provides information for contacting HP support and ordering supplies.

The onscreen Help details the full range of features and functions, including use of

the HP Photosmart software that came with the HP All-in-One.

The HP All-in-One at a glance

Label Description

1 Control panel

2 On button

3 Memory card slots

4 Input tray

5 Tray extender

6 Paper-width guide

7 Print cartridge door

8 Glass

9 Lid backing

10 Rear door

11 Rear USB port

HP All-in-One overview 5

English

Label Description

12 Power connection

* Use only with the power adapter supplied by HP.

Control panel buttons

Label Icon Name and Description

1 On button: Turns the HP All-in-One on or off. When the HP

All-in-One is off, a minimal amount of power is still used by the

device. To completely remove power, turn the HP All-in-One

off, and then unplug the power cord.

2 Quality button: Changes the copy quality or the quality of

photos you print from a memory card. The default quality for

both plain and photo papers is two stars. However, the quality

produced varies depending on the paper type. For plain paper,

two stars represents normal quality. For photo paper, two stars

represents best quality.

3 Size button: Changes the image size to 100% (Actual Size),

fits it to the page (Resize to Fit), or prints borderless images

(Borderless). The default setting is 100% for plain paper and

borderless for photo paper.

4 Copies button: Specifies the desired number of copies.

5 Cancel button: Stops a task (such as scanning or copying) or

resets settings (such as Quality and Copies).

Chapter 1

(continued)

6 HP Photosmart C4200 All-in-One series

English

Label Icon Name and Description

6 Scan button: Starts a scan. When a memory card is inserted,

this button advances to the next photo on the memory card

when pressed.

7 Start Copy Black button: Starts a black-and-white copy. In

certain situations (for example, after clearing a paper jam), this

button resumes printing. When a memory card is inserted, this

button acts as a previous image button.

8 Start Copy Color button: Starts a color copy. In certain

situations (for example, after clearing a paper jam), this button

resumes printing. When a memory card is inserted, this button

starts printing the image currently on the display.

Find more information

A variety of resources, both printed and onscreen, provide information about setting up

and using the HP All-in-One.

• Setup Guide

The Setup Guide provides instructions for setting up the HP All-in-One and installing

software. Make sure you follow the steps in the Setup Guide in order.

If you have problems during setup, see Troubleshooting in the last section of the

Setup Guide, or see “

Troubleshooting and support” on page 15 in this guide.

• Onscreen Help

The onscreen Help provides detailed instructions on features of the HP All-in-One

that are not described in this User Guide, including features that are only available

using the software you installed with the HP All-in-One.

•

www.hp.com/support

If you have Internet access, you can get help and support from the HP Web site. This

Web site offers technical support, drivers, supplies, and ordering information.

Load originals and load paper

You can copy or scan up to letter- or A4-size originals by loading them on the glass.

To load an original on the scanner glass

1. Lift the lid on the HP All-in-One.

2. Load your original print side down on the right front corner of the glass.

TIP: For more help on loading an original, refer to the engraved guides along the

edge of the glass.

(continued)

Find more information 7

English

3. Close the lid.

To load 10 x 15 cm (4 x 6 inch) photo paper in the input tray

1. Remove all paper from the input tray.

2. Insert the stack of photo paper into the far-right side of the input tray with the short

edge forward and the print side down. Slide the stack of photo paper forward until it

stops.

If the photo paper you are using has perforated tabs, load the photo paper so that the

tabs are closest to you.

TIP: For more help on loading small-size photo paper, refer to the guides

engraved in the base of the input tray for loading photo paper.

3. Slide the paper-width guide inward until it stops at the edge of the paper.

Do not overload the input tray; make sure the stack of paper fits within the input tray

and is no higher than the top of the paper-width guide.

Avoid paper jams

To help avoid paper jams, follow these guidelines.

• Remove printed papers from the output tray frequently.

• Prevent curled or wrinkled paper by storing all unused paper flat in a resealable bag.

• Ensure that paper loaded in the input tray lays flat and the edges are not bent or torn.

• Do not combine different paper types and paper sizes in the input tray; the entire stack

of paper in the input tray must be the same size and type.

Chapter 1

8 HP Photosmart C4200 All-in-One series

English

• Adjust the paper-width guide in the input tray to fit snugly against all paper. Make sure

the paper-width guide does not bend the paper in the input tray.

• Do not overload the input tray; make sure the stack of paper fits within the input tray

and is no higher than the top of the paper-width guide.

• Do not force paper too far forward in the input tray.

• Use paper types that are recommended for the HP All-in-One.

Make a copy

You can make quality copies from the control panel.

To make a copy from the control panel

1. Make sure you have paper loaded in the input tray.

2. Load your original print side down on the right front corner of the glass.

3. Press Start Copy Black or Start Copy Color to begin copying.

Scan an image

For original documents or images placed on the glass, you can start a scan from your

computer or from the HP All-in-One. This section explains the second option: how to scan

from the control panel of the HP All-in-One to a computer.

To use the scan features, the HP All-in-One and computer must be connected and turned

on. The HP Photosmart Software must also be installed and running on your computer

prior to scanning. To verify that the HP Photosmart Software is running on a Windows

computer, look for the HP Digital Imaging Monitor icon in the system tray at the lower

right side of the screen, near the time.

NOTE: Closing the HP Digital Imaging Monitor icon in the Windows system tray

can cause the HP All-in-One to lose some of its scan functionality. If this happens,

you can restore full functionality by restarting your computer.

To scan to a computer

1. Load your original print side down on the right front corner of the glass.

2. Ensure that there are no memory cards inserted in the memory card slots on the

HP All-in-One.

3. Press Scan.

A preview image of the scan appears on your computer, where you can edit it. Any

edits that you make apply to the current scan session only.

The HP Photosmart Software has many tools that you can use to edit your scanned

image. You can improve the overall image quality by adjusting the brightness,

sharpness, color tone, and saturation. You can also crop, straighten, rotate, or resize

the image.

4. Make any edits to the preview image, and then click Accept when you are finished.

Print 10 x 15 cm (4 x 6 inch) photos

You can select specific photos on your memory card to print as 10 x 15 cm (4 x 6 inch)

photos.

Make a copy 9

English

To print one or more 10 x 15 cm (4 x 6 inch) photos

1. Insert your memory card into the appropriate slot on the HP All-in-One.

The most recent image on the card appears on the display.

2. Load 10 x 15 cm (4 x 6 inch) photo paper in the input tray.

3. Press the buttons next to the

and icons on the display to scroll through the photos

on your memory card until the photo you want to print appears.

4. Do one of the following:

• For faster printing with slightly reduced resolution, leave the Quality setting at

best resolution (as indicated by the two star icons on the display).

• For maximum resolution, press the Quality button until three star icons appear

on the display.

• For the fastest printing, but with reduced resolution, press the Quality button until

the one star icon appears on the display.

5. Leave the default Size setting as Borderless.

6. Press the Copies button until the number of copies you want to print appears on the

display.

7. Press the Print button.

TIP: While the photo is printing, you can continue scrolling through the photos

on your memory card. When you see a photo you want to print, you can press

the Print button to add that photo to the print queue.

Replace the print cartridges

Follow these instructions to replace print cartridges. Following these instructions might

also help solve print quality issues related to the cartridges.

NOTE: When the ink level for the print cartridge is low, a message appears on your

computer screen. You can also check the ink levels by using the software installed

with the HP All-in-One.

When you receive a low-ink warning message, make sure you have a replacement print

cartridge available. You should also replace the print cartridges when you see faded text

or if you experience print quality issues related to the print cartridges.

To order print cartridges for the HP All-in-One, go to

www.hp.com/buy/supplies. If

prompted, choose your country/region, follow the prompts to select your product, and

then click one of the shopping links on the page.

Chapter 1

10 HP Photosmart C4200 All-in-One series

English

To replace the print cartridges

1. Make sure the HP All-in-One is on.

CAUTION: If the HP All-in-One is off when you open the print cartridge door to

access the print cartridges, the HP All-in-One will not release the cartridges for

changing. You might damage the HP All-in-One if the print cartridges are not

docked safely when you try to remove them.

2. Make sure you have letter or A4 unused plain white paper loaded in the input tray.

3. Open the print cartridge door.

The print carriage moves to the far right side of the HP All-in-One.

4. Wait until the print carriage is idle and silent, and then lightly press down on a print

cartridge to release it.

If you are replacing the tri-color print cartridge, remove the print cartridge from the

slot on the left.

If you are replacing the black or photo print cartridge, remove the print cartridge from

the slot on the right.

1 Print cartridge slot for the tri-color print cartridge

2 Print cartridge slot for the black and photo print cartridges

5. Pull the print cartridge toward you out of its slot.

6. If you are removing the black print cartridge in order to install the photo print cartridge,

store the black print cartridge in the print cartridge protector or an airtight plastic

container.

7. Remove the new print cartridge from its packaging and, being careful to touch only

the black plastic, gently remove the plastic tape by using the pink pull tab.

Replace the print cartridges 11

English

1 Copper-colored contacts

2 Plastic tape with pink pull tab (must be removed before installing)

3 Ink nozzles under tape

CAUTION: Do not touch the copper-colored contacts or ink nozzles. Touching

these parts can result in clogs, ink failure, and bad electrical connections.

8. Slide the new print cartridge forward into the empty slot. Then gently push the upper

part of the print cartridge forward until it clicks into the socket.

If you are installing the tri-color print cartridge, slide it into the left slot.

If you are installing a black or photo print cartridge, slide it into the right slot.

9. Close the print cartridge door.

Chapter 1

12 HP Photosmart C4200 All-in-One series

English

If you installed a new print cartridge, the HP All-in-One prints a print cartridge

alignment page.

10. When prompted, ensure plain white paper is loaded in the input tray, then press the

button next to OK.

NOTE: If you have colored paper loaded in the input tray when you align the print

cartridges, the alignment will fail. Load unused plain white paper into the input

tray, and then try the alignment again.

11. Place the page print side down on the scanner glass and then press the button next

to OK to scan the page.

When the On button stops flashing, the alignment is complete and the page can be

removed.

Clean the HP All-in-One

To ensure that your copies and scans remain clear, you might need to clean the glass

and lid backing. You might also want to dust the exterior of the HP All-in-One.

Clean the glass

Fingerprints, smudges, hair, and dust on the main glass surface slow down performance

and affect the accuracy of the copy and scan features.

To clean the glass

1. Turn off the HP All-in-One, unplug the power cord, and raise the lid.

2. Clean the glass with a soft cloth or sponge slightly moistened with a nonabrasive

glass cleaner.

CAUTION: Do not use abrasives, acetone, benzene, or carbon tetrachloride on

the glass, since they can damage it. Do not place or spray liquid directly on the

glass. The liquid might seep under the glass and damage the device.

3. Dry the glass with a dry, soft, lint-free cloth to prevent spotting.

4. Plug in the power cord, and then turn on the HP All-in-One.

Clean the lid backing

Minor debris can accumulate on the white document backing located underneath the lid

of the HP All-in-One.

To clean the lid backing

1. Turn off the HP All-in-One, unplug the power cord, and raise the lid.

2. Clean the white document backing with a soft cloth or sponge slightly moistened with

a mild soap and warm water.

Wash the backing gently to loosen debris. Do not scrub the backing.

3. Dry the backing with a dry, soft, lint-free cloth.

CAUTION: Do not use paper-based wipes, as these might scratch the backing.

Clean the HP All-in-One 13

English

4. If further cleaning is needed, repeat the previous steps using isopropyl (rubbing)

alcohol, and wipe the backing thoroughly with a damp cloth to remove any residual

alcohol.

CAUTION: Be careful not to spill alcohol on the glass or exterior of the HP All-

in-One, as this might damage the device.

5. Plug in the power cord, and then turn on the HP All-in-One.

Chapter 1

14 HP Photosmart C4200 All-in-One series

English

2 Troubleshooting and support

This chapter contains troubleshooting information for the HP All-in-One. Specific information is

provided for installation and configuration issues, and some operational topics. For more

troubleshooting information, see the onscreen Help that came with your software.

Many issues are caused when the HP All-in-One is connected to the computer using a USB cable

before the HP All-in-One software is installed on the computer. If you connected the HP All-in-One

to your computer before the software installation screen prompts you to do so, you must follow these

steps:

Troubleshooting common setup issues

1. Disconnect the USB cable from the computer.

2. Uninstall the software (if you have already installed it).

3. Restart your computer.

4. Turn off the HP All-in-One, wait one minute, then restart it.

5. Reinstall the HP All-in-One software.

CAUTION: Do not connect the USB cable to the computer until prompted by the software

installation screen.

For support contact information, see the inside back cover of this guide.

Uninstall and reinstall the software

If your installation is incomplete, or if you connected the USB cable to the computer before prompted

by the software installation screen, you might need to uninstall and then reinstall the software. Do

not simply delete the HP All-in-One application files from your computer. Make sure to remove them

properly using the uninstall utility provided when you installed the software that came with the HP

All-

in-One.

To uninstall from a Windows computer and then reinstall

1. On the Windows taskbar, click Start, Settings, Control Panel.

2. Double-click Add/Remove Programs.

3. Select the HP All-in-One, and then click Change/Remove.

Follow the onscreen instructions.

4. Disconnect the HP All-in-One from your computer.

5. Restart your computer.

NOTE: It is important that you disconnect the HP All-in-One before restarting your

computer. Do not connect the HP All-in-One to your computer until after you have reinstalled

the software.

6. Insert the HP All-in-One CD-ROM into your computer’s CD-ROM drive and then start the Setup

program.

7. Follow the onscreen instructions and the instructions provided in the Setup Guide that came

with the HP All-in-One.

When the software installation is complete, the HP Digital Imaging Monitor icon appears in the

Windows system tray.

To verify that the software is properly installed, double-click the HP Solution Center icon on the

desktop. If the HP Solution Center shows the essential icons (Scan Picture and Scan

Document), the software has been properly installed.

Hardware setup troubleshooting

Use this section to solve any problems you might encounter while setting up the HP All-in-One

hardware.

Troubleshooting and support 15

English

The HP All-in-One will not turn on

Cause: The HP All-in-One is not properly connected to a power supply.

Solution

• Make sure the power cord is firmly connected to both the HP All-in-One and the power

adapter. Plug the power cord into a power outlet, surge protector, or power strip.

1 Power connection

2 Power cord and adapter

3 Power outlet

• If you are using a power strip, make sure the power strip is on. Or, try plugging the HP

All-

in-One directly into a power outlet.

• Test the power outlet to make sure it is working. Plug in an appliance that you know works,

and see if the appliance has power. If not, then there might be a problem with the power

outlet.

• If you plugged the HP All-in-One into a switched outlet, make sure the switch is on. If it is

switched to on but still does not work, then there might be a problem with the power outlet.

Cause: You pressed the On button too quickly.

Solution: The HP All-in-One might not respond if you press the On button too quickly. Press

the On button once. It might take a few minutes for the HP All-in-One to turn on. If you press

the On button again during this time, you might turn the device off.

CAUTION: If the HP All-in-One still does not turn on, it might have a mechanical failure.

Unplug the HP All-in-One from the power outlet and contact HP. Go to:

www.hp.com/

support. If prompted, choose your country/region, and then click Contact HP for information

on calling for technical support.

I connected the USB cable, but I am having problems using the HP All-in-One with

my computer

Cause: The USB cable was connected before the software was installed. Connecting the USB

cable before prompted can cause errors.

Solution: You must first install the software that came with the HP All-in-One before

connecting the USB cable. During installation, do not plug in the USB cable until prompted by

the onscreen instructions.

Once you have installed the software, connecting your computer to the HP All-in-One with a

USB cable is straightforward. Simply plug one end of the USB cable into the back of your

Chapter 2

16 HP Photosmart C4200 All-in-One series

English

computer and the other into the back of the HP All-in-One. You can connect to any USB port on

the back of your computer.

For more information on installing the software and connecting the USB cable, see the Setup

Guide that came with the HP All-in-One.

The HP All-in-One does not print

Solution: If the HP All-in-One and computer are not communicating with each other, try the

following:

•

plugged into a power outlet. Press the On button to turn on the HP All-in-One.

• Make sure the print cartridges are installed.

• Make sure you have paper loaded in the input tray.

• Check that the HP All-in-One does not have a paper jam.

• Check that the print carriage is not jammed.

Open the print cartridge door to access the print carriage area. Remove any objects that

are blocking the print carriage, including any packing materials. Turn the HP All-in-One off

and then turn it on again.

• Check that the HP All-in-One print queue is not paused (Windows) or stopped (Mac). If it

is, choose the appropriate setting to resume printing. For more information about accessing

the print queue, see the documentation that came with the operating system installed on

your computer.

• Check the USB cable. If you are using an older cable, it might not be working properly. Try

connecting it to another product to see if the USB cable works. If you experience problems,

the USB cable might need to be replaced. Also verify that the cable does not exceed 3

meters (9.8 feet) in length.

• Make sure your computer is USB ready. Some operating systems, such as Windows 95

and Windows NT, do not support USB connections. Check the documentation that came

with your operating system for more information.

• Check the connection from the HP All-in-One to your computer. Verify that the USB cable

is securely plugged into the USB port on the back of the HP All-in-One. Make sure the other

end of the USB cable is plugged into a USB port on your computer. After the cable is

connected properly, turn the HP All-in-One off and then on again.

• If you are connecting the HP All-in-One through a USB hub, make sure the hub is turned

on. If the hub is on, try connecting directly to your computer.

Hardware setup troubleshooting 17

English

One

is turned off. Make sure the power cord is firmly connected to the HP All-in-One and

Look at the On light located on the front of the HP All-in-One. If it is not lit, the HP All-in-

• Check other printers or scanners. You might need to disconnect older products from your

computer.

• Try connecting the USB cable to another USB port on your computer. After you check the

connections, try restarting your computer. Turn the HP All-in-One off and then on again.

• If the HP All-in-One is offline, turn the HP All-in-One off and on again. Start a print job.

• If necessary, remove and then install the software you installed with the HP All-in-One again.

For more information on setting up the HP All-in-One and connecting it to your computer, see

the Setup Guide that came with the HP All-in-One.

Clear paper jams

If the HP All-in-One has a paper jam, first check the rear door.

If the jammed paper is not in the rear rollers, check the front door.

To clear a paper jam from the rear door

1. Press in the tab on the left side of the rear door to release the door. Remove the door by pulling

it away from the HP All-in-One.

2. Gently pull the paper out of the rollers.

CAUTION: If the paper tears when you are removing it from the rollers, check the rollers

and wheels for torn pieces of paper that might be remaining inside the device. If you do not

remove all the pieces of paper from the HP All-in-One, more paper jams are likely to occur.

3. Replace the rear door. Gently push the door forward until it snaps into place.

4. Press Start Copy Black or Start Copy Color to continue the current job.

To clear a paper jam from the front door

1. If necessary, pull the input tray down to open it. Then, lower the print cartridge door.

2. Gently pull the paper out of the rollers.

CAUTION: If the paper tears when you are removing it from the rollers, check the rollers

and wheels for torn pieces of paper that might be remaining inside the device. If you do not

remove all the pieces of paper from the HP All-in-One, more paper jams are likely to occur.

Chapter 2

18 HP Photosmart C4200 All-in-One series

English

3. Close the print cartridge door.

4. Press Start Copy Black to continue the current job.

Print cartridge troubleshooting

If you are experiencing problems with printing, you might have a problem with one of the print

cartridges. For more information, see “

Replace the print cartridges” on page 10 in this guide.

Support process

If you have a problem, follow these steps:

1. Check the documentation that came with the HP All-in-One.

2. Visit the HP online support Web site at

www.hp.com/support. HP online support is available to

all HP customers. It is the fastest source for up-to-date device information and expert assistance

and includes the following features:

• Fast access to qualified online support specialists

• Software and driver updates for the HP All-in-One

• Valuable HP All-in-One and troubleshooting information for common problems

• Proactive device updates, support alerts, and HP newsgrams that are available when you

3. Call HP support. Support options and availability vary by device, country/region, and language.

For a list of support phone numbers, see the inside back cover of this guide.

Print cartridge troubleshooting 19

English

3 Technical information

The technical specifications and international regulatory information for the HP All-in-One are

provided in this section.

System requirements

Software system requirements are located in the Readme file.

Product specifications

For product specifications, go to the HP Web site at www.hp.com/support.

Paper specifications

• Input tray capacity: Plain paper sheets: Up to 100 (20 lb./75 gsm. paper)

• Output tray capacity: Plain paper sheets: Up to 50 (20 lb./75 gsm. paper)

NOTE: For a complete list of supported media sizes, see the printer software.

Physical specifications

• Height: 16.97 cm (7.0 inches)

• Width: 44 cm (16.8 inches)

• Depth: 25.9 cm (10.2 inches)

• Weight: 4.5 kg (10 pounds)

Power specifications

• Power consumption: 25 watts maximum (average printing)

• Input voltage: AC 100 to 240 V ~ 600 mA 50–60 Hz

• Output voltage: DC 32 V===375 mA, 16 V===500 mA

NOTE: Use only with the power adapter supplied by HP.

Environmental specifications

• Recommended operating temperature range: 15º to 32º C (59º to 90º F)

• Allowable operating temperature range: 5º to 35º C (41º to 95º F)

• Humidity: 15% to 80% RH non-condensing

• Non-operating (Storage) temperature range: –20º to 50º C (–4º to 122º F)

• In the presence of high electromagnetic fields, it is possible the output from the HP All-in-One

may be slightly distorted

• HP recommends using a USB cable less than or equal to 3 m (10 feet) in length to minimize

injected noise due to potential high electromagnetic fields

Print cartridge yield

Ink from the cartridges is used in the printing process in a number of different ways, including in the

initialization process, which prepares the device and cartridges for printing, and in printhead

servicing, which keeps print nozzles clear and ink flowing smoothly. In addition, some residual ink

is left in the cartridge after it is used. For more information, see

www.hp.com/go/inkusage.

Visit

www.hp.com/pageyield for more information on estimated cartridge yields.

Regulatory notices

The HP All-in-One meets product requirements from regulatory agencies in your country/region. For

a complete listing of regulatory notices, see the onscreen Help.

20 HP Photosmart C4200 All-in-One series

English

La page est en cours de chargement...

HP Photosmart C4200 All-in-One Printer series Mode d'emploi

Marque: HP

Modèle: Photosmart C4200 All-in-One Printer series

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: HP Photosmart C4200 All-in-One Printer series User guide

HP Photosmart C4200 All-in-One Printer series Mode d'emploi

HP Photosmart C4200 All-in-One Printer series Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents