Candy CHK46C Manuel utilisateur

Marque: Candy

Modèle: CHK46C

Catégorie: Plaques de cuisson

Taper: Manuel utilisateur



CHK46C

CeramicHob

InstructionManual



Content

1…………………………………..…………………Safetyinstructions



2…………………………………..…………………Installation



3…………………………………..…………………DescriptionoftheCeramichobsurfacelayout



4…………………………………..…………………Usingtheceramichob



5…………………………………..…………………Hobguidelines



6…………………………………..…………………Maintenanceandcleaning



7…………………………………..…………………Environmentalnote



Safety instructions

This User Instruction Manual contains important information, including safety

& installation points, which will enable you to get the most out of your

appliance. Please keep it in a safe place so that it is easily available for future

reference; for you or any person not familiar with the operation of the appliance.

Caution!

⚫ Do not use the ceramic hob until you

have read this instruction manual.

The ceramic hob is intended for

household use only.

⚫ The appliance becomes hot during

operation. Take care not to touch the

hot surface.

⚫ Always keep children away from the

ceramic hob.

⚫ While in operation direct contact with

the ceramic hob may cause burns!

⚫ Ensure that small items of household

equipment, including connection leads,

do not touch the hob as the insulation

material of this equipment is usually

not resistant to high temperatures.

⚫ Do not leave the ceramic hob

unattended when frying. Oils and fats

may catch fire due to overheating or

boiling over.

⚫ Do not switch on the hob until a pan

has been placed on it.

⚫ Do not put pans weighing over 25kg

on the hob.

⚫ Do not use the ceramic hob in the

event of a technical fault. Any faults

must be fixed by an appropriately

qualified and authorized person.

⚫ In the event of any incident caused by

a technical fault, disconnect the power

and report the fault to the service

centre to be repaired.

⚫ The rules and provisions contained in

this instruction manual should be

strictly observed. Do not allow

anybody who is not familiar with the

contents of this instruction manual to

operate the ceramic hob.

⚫ The ceramic hob should not be

cleaned using steam cleaning

equipment.

⚫ IMPORTANT: The adjacent

furniture or housing and all materials

used in the installation must be able to

withstand a minimum temperature of

95°C above the ambient temperature

of the room it is located in, whilst in

use.

⚫ Any damage caused by the appliance

being installed in contravention of this

temperature limit, or by placing

adjacent cabinet materials closer than

4mm to the appliance, will be the

liability of the owner.

⚫ This appliance complies with all

current European safety legislation.

We do wish to emphasize that this

compliance does not remove the fact

that the appliance surfaces will

become hot during use and retain heat

after operation.

Child Safety

⚫ We strongly recommend that

babies and young children are

prevented from being near to the

appliance and not allowed to touch

the appliance at any time.

⚫ If it is necessary for younger family

members to be in the kitchen,

please ensure that they are kept

under close supervision at all times.

General Safety

⚫ This appliance is not intended for

use by persons (including children)

with reduced physical, sensory or

mental capabilities, or lack of

experience and knowledge, unless

they have been given supervision

or instruction concerning use of the

appliance by a person responsible

for their safety.

⚫ Children should be supervised to

ensure that they do not play with

the appliance.

⚫ NEVER try to extinguish a fire with

water, but switch off the appliance

and then cover flame e.g. with a lid

or a fire blanket.

⚫ WARNING: Danger of fire: do not

store items on the cooking surfaces.

⚫ Means for disconnection must be

incorporated in the fixed wiring in

accordance with the wiring rules.

⚫ Do not allow electrical fittings or

cables to come into contact with

areas on the appliance that get hot.

⚫ Do not use the appliance to heat

the room it is located in or to dry

clothing.

⚫ Do not install the appliance next to

curtains or soft furnishings.

⚫ If the supply cord is damaged, it

must be replaced by the

manufacturer, its service agent or

similarly qualified persons in order

to avoid a hazard.

⚫ The appliance is not intended to be

operated by means of an external

timer or separate remote-control

system.

⚫ Power cord can’t accessible after

installation.

⚫ This product can be worked but not

through outside timer and remote

control.

⚫ Warning: If the surface is cracked,

switch off the appliance to avoid the

possibility of electric shock, for hob

surfaces of glass ceramic or similar

material which protect live parts.

⚫ Warning: a steam cleaner is not be

used.

⚫ CAUTION: The cooking process

has to be supervised. A short term

cooking process has to be

supervised continuously.

⚫ WARNING: Unattended cooking

on a hob with fat or oil can be

dangerous and may result in a fire.

⚫ This appliance should be

connected to a circuit which

incorporates an isolating switch

which can accessible by the user

after installation providing full

disconnection from the power

supply. The disconnection may be

achieved by incorporating a switch

in the fixed wiring in accordance

with the wiring rules.

⚫ Warning: Before obtaining access

to terminals, all supply circuits must

be disconnected.

⚫ WARNING: Use only hob guards

the cooking appliance or indicated

by the manufacturer of the

appliance in the instructions for use

as suitable or hob guards

incorporated in the appliance. The

use of inappropriate guards can

cause accidents.

⚫ WARNING: The appliance and its

accessible parts become hot during

use.

⚫ Care should be taken to avoid

touching heating elements.

⚫ Regarding the instructions for how

to Installation,thanks to refer to the

section “Installation”.

Installation

Electrical connection

Before connecting the appliance, make sure that the supply voltage

marked on the Rating Plate corresponds with your mains supply voltage.

WARNING: THIS APPLIANCE MUST BE EARTHED.

⚫ If you have to change the oven power cord, the earthing (yellow/green) conductor

must always be 10 mm longer than the line conductors.

⚫ Care must be taken to ensure that the temperature of the mains supply cable does

not exceed 50°C.

⚫ If the mains supply cable is damaged, then it must be replaced by an appropriate

replacement which can be obtained from Spares Department.

Assembly of ceramic hob :

Preparing the unit for a built-in appliance

WARNING

The kitchen units that are in direct contact with the appliances must be heat-

proof(min. 95°).

The appliance can be installed on a work surface with a thickness of between 30

and 40 mm and near to walls which are higher than the work surface,maintaining a

minimum distance of 100 mm.

Carry out all cutting of the unit and work surface then carefully remove shavings or

sawdust before inserting the appliances.

To ensure a correct ventilation of the hob please comply with the dimensions

shows in figures .

Always refer to the manufacturer for specific instructions,

Make sure the surface is level and square and that no part interferes with the

space required for installation.

Prepare the cut as indicated(see installation dimensions).

Installing the hob

WARNING

Risk of cutting.

Be careful of cutting edges.

End parts in foamed plastic - be careful.

During transportation these could cause slight injury or cuts.

Remove the material and envelope of documents from the packaging.

Before proceeding with installation read the work instructions carefully.

Step.1

Put a towel or cloth on the work surface.Place the hob face

down on the protected surface.

Step.2

Apply the strip seal,supplied with the hob,which is for sealing

it onto the work surface.

Do not use silicone. Apply the seal to the edge of the bottom

of the hob,leaving about 3mm from the edge of the glass.

Apply the seal all around the circumference.

Cut any excess and bring the two ends of the seal together

so they match.

Step.3

Fix the brackets(4 pcs) on the front side and rear side by screw.Put the hob in the cut-

out cabinet,and make it centered.Ensure that the front edge of the hob is parallel to the

side edge of the work surface.

⚫ IMPORTANT: You must observe the ventilation

requirements shown in the drawing opposite.

⚫ IMPORTANT: There are ventilation holes around the

outside of the hob. YOU MUST ensure that these

holes are not blocked by the work top, when you put

the hob into position (see drawing opposite).

⚫ IMPORTANT: Do not use a silicon sealant to seal the

appliance against the aperture. This will make it

difficult to remove the hob from the aperture in future,

particularly if it needs to be serviced.

⚫ Carefully turn the hob back over and then gently lower it into the aperture hole that

you have cut out.

Fitting guidelines

The ceramic hob is manufactured to work with two-phase

alternating current (400V2N~50Hz).The voltage rating of the

ceramic hob heating elements is 230V. Adapting the ceramic

hob to operate with one-phase current is possible by

appropriate bridging in the connection box according to the

connection diagram below. The connection diagram is also

found on the cover of the connection box. Remember that

the connection wire should match the connection type and

the power rating of the ceramic hob.

The connection cable must be secured in a strain-relief clamp.

Warning!

Remember to connect the safety circuit to the connection box terminal marked with

.The electricity supply for the ceramic hob must have a safety switch which

enables the power to be cut off in case of emergency. The distance between the

working contacts of the safety switch must be at least 3mm.

Before connecting the ceramic hob to the power supply it is important to read the

information on the data plate and the connection diagram.

wires for each domino hob with 4D models

model

Adaptive voltage range and wires

The wiring diagram

220-240 1N～

50-60Hz

380-420 2N～ 50-

60Hz

KADO K 1/5

AHW-4A1-60-R

H05VV-F 3G2.5

H05VV-F 4G2.5

H05GG-F 4G2.5

H07RN-F 4G2.5

KADO XT

⚫ The cable connections must be in accordance with the diagram located on the

bottom of the hob.

⚫ The cable type must be connected to the corresponding power supply terminal box.

⚫ You should use a good quality screwdriver to carefully, fully tighten ALL of the

terminal screws.

⚫ If when the hob is first switched on, only two of the zones work, you should

recheck that the terminal screws are all fully tightened. This should be done before

contacting the Customer Care Department.

⚫ IMPORTANT: The appliance must NOT be connected to the mains supply by

means of a 13A plug and socket.

⚫ This appliance must be wired into a 30 A double pole switched fused spur outlet,

having 3 mm contact separation and placed in an easily accessible position

adjacent to the appliance. It should not be located above the appliance and no

more than 1.25m away from it.

⚫ The cable can be looped if necessary, but make sure that is not kinked or trapped

when the hob is in position. Care must be taken to avoid the cable being in contact

with hot parts of the appliance.

Replacing the mains supply cable

 If the mains supply cable is damaged, then it must be replaced by an appropriate

replacement.

 The mains supply cable should be replaced in accordance with the following

instructions:

➢ Switch the appliance off at the control switch.

➢ Open the terminal block on the underside of the hob.

➢ Unscrew the terminal screws fixing the cable.

➢ The “green-yellow” earth wire must be connected to the terminal marked . It

must be about 10 mm longer than the live and neutral wires.

➢ The “blue” neutral wire must be connected to the terminal marked with letter (N)

- the live wire(L1) must be connected to the terminal marked with letter (L1)

(220-240V 1N～).

➢ The “blue” neutral wire must be connected to the terminal marked with letter (N)

- the live wire L1 must be connected to the terminal marked with letter (L1),. the

live wire L2 must be connected to the terminal marked with letter (L2) (380-

420V 2N～).

Description of the Ceramic hob surface layout

4 zone ceramic hob schematic diagram

Display mode and control

1.1 Display mode

✓ Cooking zone working indicator: the corresponding indicator light display when the

cooking zone is working;

✓ Cooking zone residual heat indicator: the corresponding indicator flashes when the

cooking zone stops working (once every 1 second);

✓ The whole hob standby mode indicator: all cooking zone indicator lights alternately

turn on and off .

✓ Touch button(power button)+ programming button(Corresponding hob top power

level selecting).

1.2 Control panel

2.1 Control panel layout:

Icons &

programming button

Function

Power button: press and hold to turn on or off the hob

BM1

NO.1 cooking zone power level selecting

BM2

NO.2 cooking zone power level selecting

BM3

NO.3 cooking zone power level selecting

BM4

NO.4 cooking zone power level selecting

2.2 Display section

Indicator

light

Function

NO.1 cookingzone indicating digital tube:display the power

level , high temperature warning symbol etc.

NO.2 cookingzone indicating digital tube:display the power

level , high temperature warning symbol etc.

NO.3 cookingzone indicating digital tube:display the power

level , high temperature warning symbol etc.

NO.4 cookingzone indicating digital tube:display the power

level , high temperature warning symbol etc.

Using the ceramic hob

Before first use

IMPORTANT: You should clean the ceramic hob surface (see “Maintenance

and cleaning” section).

✓ You should switch on one cooking zone at a time, for 5 minutes at the maximum

setting. This will help to eliminate any new smell that exists and evaporate any

humidity that has formed on the heating elements during transit.

✓ Do not burn off more than one zone at once.

✓ You must place a saucepan filled half full with cold water on each zone as you

burn it off.

1. Power on

✓ After switch on the appliance, all of the indicator digital tubes on the display screen

will lit on for 2s, then the appliance goes into shutdown mode.

✓ Shutdown status: All the display will close except the indicator light of the heated

cooking zone always on, all of display screen will be off. At this time, only the

power button “ ” can operated by pressing and holding, and other programming

button operations are invalid.

2. Standby mode

✓ Under shutdown status, press and hold “ ” button for 3s, all cooking zone

indicator lights alternately turn on and off . The hob will enter standby mode.

✓ Under standby mode, if no any cooking zone heating operation, the appliance will

go into shutdown status automatically after 10s.

3. Heating control

✓ Under standby mode, you can choose the cooking zone power level by pressing

the programming button. In the process of adjusting the power level, clockwise

rotation can increase the power level from 0 to 15(maximum), and then rotate

back to “0” for a cycle; Counterclockwise rotation can be adjusted from15 to 1

power levels, and then rotate back to “0” for a cycle.

✓ When the hob top is in heating status, press and hold “ ” power button for 3s to

switch off, and stop all the cooking zones to heat. The corresponding cooking zone

indicator of the hob top which has heated before will display high temperature

warning .

✓ Under standby mode, if some hob tops still exist residual heat, corresponding hob

top indicator light will display.

✓ If needing to switch off one of the cooking zones, you can select corresponding

the hob top's programming button to adjust the power level to “0” to switch off that

zone, and will not affect the heating of the other cooking zones. When power level

reaches “0”, the corresponding cooking zone indicator of the hob top which has

heated before will display.

✓ If more than one zone is operating at the same time, total power will equal to the

sum of the powers of all the working cooking zones, each cooking zone will work

according to their power modulation ratio, and will not affect each other.

✓ You can select the appropriate output power level by rotating the programming

button of the corresponding hob.

✓ The power level is divided into 16 levels, including the shutdown level (0 level). For

the programming button, rotating clockwise to increase the power level, and

rotating counterclockwise to decrease the power level. When rotating

counterclockwise, if the fire power position is “0” at the beginning, you will adjust to

15 level and then reduce the level in turn.

✓ When switching any of the cooking zone power level to 0, it will stop the power

output of that cooking zone.

✓ If a cooking zone has been heated,power level of all the cooking zone are “0”, the

appliance will automatically enter into shutdown status after 1 minute no operation.

4. Shutdown

✓ Under standby mode or heating mode, press and holding “ ” button for 3s,the

appliance will go into shutdown mode. If there is residual heat in the corresponding

cooking surface at this time, the corresponding cooking zone indicator flashes,

indicating a warning of residual heat.

7. Default timing

✓ All the cooking zones have default timing function.The relationship of default

timing and power level refers to table below:

Power Level

7-15

Default timing(h)

1.5h

✓ When all the default timing is reached, the cooking zones will switch off

automatically and enter into standby mode.

8.High temperature warning

✓ Press and hold power button “ ” manually for 3s till switch off, the whole

appliance will stop heating, but the cooking surface still has high temperature, the

indicator light of the cooking zone that stops heating flashes, indicating that the

corresponding heating furnace surface is hot.

✓ As long as the cooking zone has heated before, the indicator light will display for

35 minutes continually after the hob turn off.

9.Protection function

✓ High temperature protection: The electronic temperature sensor on the control

panel will transmit the real-time temperature to the chip of the control panel. The

control sensor starts protection when the electronic temperature sensor gauge the

current temperature is higher than a certain value, to reduce the heating level of

the cooking zone currently, and resumes the heating level after the temperature

drops.

✓ Residual heat protection: When the whole appliance stops heating, the indicator

light of the relative cooking zone will display, indicating that cooking surface

temperature is too high, please do not touch to avoid getting burned.

✓ Safety cut-off protection:For the models with plug,when cut off after 1S at any

time,the voltage between L/N of the plug should fall to below safe voltage range.

10. PCB board fault codes and solutions

When a PCB board failure occurs, the timer digital tubes on the display panel always

display the fault code, and all the burners that are being heated stop heating, and

automatically return to the shutdown state after 1 minute. For the burners that have

been worked, their indicator light continue to display slowly (display 1 time per

second) , indicating that cooking surface temperature is too high. When the fault code

appears, please refer to the scheme in the following table to solve.

How to use the hot plate

Put the pot in center of the heating zone, Turn the knob clockwise and anticlockwise to

turn on the hob.

Fault code

Type of fault

Solution

All indicator lights

display quickly

(display

0.5s/times)

The display board does not

receive the signal of power

supply board.

The communication line failure

of power supply board or

display board can cause

communication anomalies.

Replace the display board

first. If the fault persists,

replace the power supply

board.

All indicator lights

display quickly

(display

0.5s/times)

The power supply board does

not receive the signal of

display board.

All indicator lights

display quickly

(display

0.5s/times)

Power supply board relay

failure

Replace the power supply

board.

All indicator lights

display quickly

(display

0.5s/times)

1.Open circuit of the display

board NTC.

2.Short circuit of the display

board NTC.

Replace the display board

All indicator lights

display quickly

(display

0.5s/times)

High temperature protection

on the display board.

Replace the Insulated silicone

strip of circuit panel first. If

the fault persists, replace the

display board .

High temperature indication lamp:

When the glass plate is too hot, the high temperature indication lamp will light up, don’t

touch the glass plate until the indication lamp goes out.

Shut down:after using,please turn the knob to “OFF”,the hob will stop heating.

Caution!

➢ Ensure the heating plate is clean-a soiled zone does not transfer all of the heat.

➢ Protect the plate against corrosion.

➢ Switch off the plate against corrosion.

➢ Do not leave pans with prepared dishes based on fats and oils unattended on the

switched-on plate; hot fat can spontaneously catch fire.

Hob guidelines

 The first few times the hob top is used, it may give off an acrid, burning smell. This

smell will disappear completely with repeated use.

 The worktop is fitted with cooking areas of different diameter and power.

 The positions where the heat will radiate from are clearly marked on the hob top.

The saucepans must be positioned exactly on these zones for efficient heating to

occur. Pans should have the same diameter as the cooking zone that they are

being used on.

 You should not use saucepans with rough bottoms, as this can scratch the

ceramic surface.

 Before use, make sure that the bottoms of the saucepans are clean and dry.

 When cold, the bottom of the pans should be slightly concave, as they expand

when hot and lie flat on the surface of the hob. This will allow the heat to transfer

more easily.

 The best thickness for the bottom of the pans is 2 – 3 mm of enamelled steel and

4 – 6 mm for stainless steel with sandwich type bottoms.

 If these rules are not followed, then there will be a great loss of heat and energy.

Heat not absorbed by the saucepan, will spread to the hob, frame and surrounding

cabinets.

 Preferably cover pans with a lid to permit cooking at a lower heat.

 Always cook vegetables and potatoes, etc. in as little water to reduce cooking

times.

 Food or liquid that has high sugar content may damage the hob top if it comes into

contact with the ceramic hob surface. Any spillages should be wiped up

immediately, however this may not prevent the hob surface from becoming

damaged.

IMPORTANT: The ceramic hob surface is tough; however it is not unbreakable

and can be damaged. Especially if pointed or hard objects are allowed to fall on it

with some force.

Maintenance and cleaning

Cleaning operations must only be carried out when the hob is cool.

The appliance should be disconnected from your mains supply before

commencing any cleaning process.

Cleaning the ceramic hob top

Any residues that are left on the hob top surface from cleaning agents will

damage it. You should remove any residues with warm water mixed with a little

washing up liquid.

Abrasive cleaners or sharp objects will damage the hob surface; you should

clean it using warm water mixed with a little washing up liquid.

You may find it easier to clean some deposits whilst the hob surface is still

warm. However you should take care not to burn yourself if cleaning the hob

surface when it is still warm.

After each use

◆ Wipe the appliance over with a damp cloth.

◆ Dry the appliance by rubbing the surface with a clean cloth.

Cleaning table

Type of deposit

Remove

immediately?

Remove when

the appliance

has cooled

down?

What should I use

to remove the

deposit?

Sugar or food/liquid

containing sugar

Yes

Ceramic hob scraper

Tin foil or plastic

Yes

Ceramic hob scraper

Fat splashes

Yes

Ceramic hob cleaner

Metallic

discolouration

Yes

Ceramic hob cleaner

Water splashes or

water rings

Yes

Ceramic hob cleaner

Important!

The inside of the hob should only be washed with warm water and a small amount of

washing-up liquid.

Caution!

Ensure the heating plate is clean-a soiled zone does not transfer all of the heat.

Protect the hob against corrosion.

Switch off the hob against corrosion.

Do not leave pans with prepared dishes based on fats and oils unattended on the

switched-on plate; hot fat can spontaneously catch fire.

IMPORTANT: If your appliance appears not to be operating correctly, Please

contact with dealer.

DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF.

Please note that if an engineer is asked to attend whilst the product is under guarantee

and finds that the problem is not the result of an appliance fault, then you may be

liable for the cost of the call out charge.

The appliance must be accessible for the engineer to perform any necessary repair. If

your appliance is installed in such a way that an engineer is concerned that damage

will be caused to the appliance or your kitchen, then he will not complete a repair.

Environmental note

Note: Before discarding an old appliance, switch off and disconnect it from

the power supply. Cut off and render any plug useless. Cut the cable off

directly behind the appliance to prevent misuse. This should be undertaken

by a competent person.

This appliance is marked according to the European directive 2002/96/EC on Waste

electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of

correctly, you will help prevent potential negative consequences for the environment

and human health, which could otherwise be caused by inappropriate waste handling

of this product.

The symbol on the product or on the documents accompanying the product

indicates that this appliance may not be treated as household waste.

Instead it shall be handed over to the applicable collection point for the recycling of

electrical and electronic equipment.

Disposal must be carried out in accordance with local environmental regulations for

waste disposal. For more detailed information about treatment, recovery and recycling

of this product, please contact your local city office or local waste management office.

The packaging materials that we use are environmentally friendly and can be recycled.

Please discard all packaging material with due regard for the environment.

Manuel d'utilisation

de la

table de cuisson en céramique



Sommaire

Consignes de sécurité ............................................................................................................................... 3

Installation ................................................................................................................................................. 5

Description de la disposition de la surface de la plaque de cuisson vitrocéramique ................................ 10

Utilisation de la plaque de cuisson vitrocéramique ................................................................................... 11

Recommandations relatives à la table de cuisson .................................................................................... 15

Entretien et nettoyage .............................................................................................................................. 15

Note environnementale ............................................................................................................................ 17

Consignes de sécurité

Cette notice utilisateur contient des informations importantes, y compris des points de sécurité

et d'installation, qui vous permettront de tirer le meilleur parti de votre appareil. Conservez-le

dans un endroit sûr afin qu'il soit facilement consultable à l'avenir ; pour vous et toute personne

ne connaissant pas le fonctionnement de l'appareil.

Attention!

 N'utilisez pas la plaque vitrocéramique

tant que vous n'avez pas lu cette notice

d'utilisation. La plaque de cuisson en

céramique est réservée à un usage

domestique.

 L'appareil chauffe pendant l'utilisation.

Veillez à ne pas toucher la surface

chaude.

 Gardez toujours les enfants à l'écart de la

plaque vitrocéramique.

 Pendant le fonctionnement, un contact

direct avec la plaque de cuisson en

céramique peut causer des brûlures !

 Assurez-vous que les petits éléments de

l'équipement ménager, y compris les fils

de connexion, ne touchent pas la plaque

de cuisson, car le matériau isolant de cet

équipement n'est généralement pas

résistant aux températures élevées.

 Ne laissez pas la plaque de cuisson en

céramique sans surveillance pendant la

friture. Les huiles et graisses peuvent

prendre feu en raison de la surchauffe ou

de l'ébullition.

 N'allumez pas la plaque de cuisson tant

qu'une poêle n'a pas été placée dessus.

 Ne pas mettre de casseroles de plus de

25 kg sur la plaque de cuisson.

 Ne pas utiliser la plaque céramique en

cas de défaut technique. Toute panne doit

être réparée par une personne agréée et

formée de manière appropriée.

 En cas d'incident causé par un défaut

technique, débranchez l'alimentation et

signalez le défaut à réparer au centre de

service.

 Les règles et dispositions contenues dans

cette notice d'utilisation doivent être

strictement respectées. Ne permettez pas

à quiconque qui ne connaît pas le

contenu de ce manuel d'instruction de

faire fonctionner la plaque de cuisson en

céramique.

 La plaque vitrocéramique ne doit pas être

nettoyée à l'aide d'un équipement de

nettoyage à la vapeur.

 IMPORTANT : Les meubles ou

logements adjacents et tous les matériaux

utilisés dans l'installation doivent pouvoir

résister à une température minimale de

95°C supérieure à la température

ambiante de la pièce dans laquelle ils se

trouvent, pendant l'utilisation.

 Tout dommage causé par l'installation de

l'appareil en violation de cette limite de

température, ou en plaçant les matériaux

de l'armoire adjacente à moins de 4 mm

de l'appareil, sera à la charge du

propriétaire.

 Cet appareil est conforme à l'ensemble de

la législation européenne en vigueur en

matière de sécurité. Nous tenons à

souligner que cette conformité n'élimine

pas le fait que les surfaces de l'appareil

deviendront chaudes pendant l'utilisation

et retiendront la chaleur après le

fonctionnement.

Sécurité des enfants

 Nous recommandons vivement

d'empêcher les bébés et les jeunes

enfants d'être près de l'appareil et de ne

pas le toucher à tout moment.

 S'il est nécessaire que les jeunes

membres de la famille soient dans la

cuisine, veuillez vous assurer qu'ils sont

maintenus sous surveillance étroite en

tout temps.

Sécurité générale

 L’utilisation de cet appareil est interdite à

toutes les personnes (y compris les

enfants) dont les capacités physiques et

mentales sont réduites, ou qui sont

dépourvues d’expérience dans l’utilisation

d’appareils électriques, à moins qu’elles

ne soient surveillées ou instruites par des

adultes et personnes responsables de

leur sécurité.

 Les enfants doivent rester sous

surveillance afin d’être sûrs qu'ils ne

jouent pas avec l'appareil.

 N’essayez JAMAIS d’éteindre un feu avec

de l’eau, mais éteignez l’appareil, puis

couvrez la flamme avec un couvercle ou

une couverture anti-feu, par exemple.

 AVERTISSEMENT : Risque

d’incendie : ne pas stocker d'objets sur les

surfaces de cuisson.

 Des moyens de déconnexion doivent être

incorporés dans le câblage fixe

conformément aux règles de câblage.

 Ne laissez pas les raccords ou câbles

électriques entrer en contact avec des

zones chaudes de l'appareil.

 Ne pas utiliser l'appareil pour chauffer la

pièce dans laquelle il se trouve ou pour

sécher les vêtements.

 N'installez pas l'appareil à côté de rideaux

ou de tissus d'ameublement.

 Si le câble d'alimentation est endommagé,

il doit être remplacé par le fabricant, son

agent d'entretien ou des personnes

dotées du même type de qualification, afin

d'éviter tout risque.

 L'appareil n'est pas destiné à être utilisé

au moyen d'une minuterie externe ou d'un

système de télécommande séparé.

 Le cordon d'alimentation ne peut pas être

accessible après l'installation.

 Ce produit peut être utilisé mais pas avec

une minuterie extérieure et une

télécommande.

 Avertissement : Si la surface est

fissurée, éteignez l’appareil pour éviter

tout risque d’électrocution, pour les tables

de cuisson en vitrocéramique ou matériau

similaire qui protègent les pièces sous

tension

 Attention : les nettoyeurs à vapeur ne

doivent pas être utilisés.

 ATTENTION : La cuisson doit être

surveillée. Les cuissons de courte durée

doivent être surveillées en permanence.

 AVERTISSEMENT : Faire chauffer

la plaque sans surveillance avec de la

graisse ou de l’huile peut être dangereux

et provoquer un incendie.

 Cet appareil doit être connecté à un circuit

qui intègre un interrupteur d'isolement

accessible à l'utilisateur après l'installation

assurant une déconnexion complète de

l'alimentation. La déconnexion peut être

réalisée en incorporant un commutateur

dans le câblage fixe conformément aux

règles de câblage.

 Avertissement : Avant d’accéder aux

appareils, tous les circuits d’alimentation

doivent être coupés.

 AVERTISSEMENT : Utilisez

uniquement le dispositif de protection de

votre table de cuisson conçu par le

fabricant de votre appareil ou un dispositif

indiqué par celui-ci comme étant

compatible ou bien utilisez le dispositif de

protection fourni avec l’appareil.

L’utilisation d’un dispositif de protection

non approprié peut provoquer des

accidents.

 AVERTISSEMENT : L’appareil et

ses parties accessibles chauffent pendant

l’utilisation.

 Des précautions doivent être prises pour

éviter de toucher les éléments chauffants.

 En ce qui concerne les instructions

d'installation, veuillez vous référer à la

section «Installation».

La page charge ...

Candy CHK46C Manuel utilisateur

Marque: Candy

Modèle: CHK46C

Catégorie: Plaques de cuisson

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Candy CHK46C User manual

Candy CHK46C Manuel utilisateur

Candy CHK46C Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents