Sony CDP-CE575 Le manuel du propriétaire

Marque: Sony

Modèle: CDP-CE575

Catégorie: Lecteur CD

Taper: Le manuel du propriétaire

Compact Disc

Player

4-233-301-22 (1)

CDP-CE575

Operating Instructions

Mode d’emploi

About this manual

The instructions in this manual is for CDP-CE575.

Tip

Instructions in this manual describe the controls on

the player.

You can also use the controls on the remote if they

have the same or similar names as those on the

player.

This Class A digital apparatus complies with

Canadian ICES-003.

CAUTION

TO PREVENT ELECTRIC SHOCK, DO NOT USE

THIS POLARIZED AC PLUG WITH AN

EXTENSION CORD, RECEPTACLE OR OTHER

OUTLET UNLESS THE BLADES CAN BE FULLY

INSERTED TO PREVENT BLADE EXPOSURE.

Table of Contents

Parts Identification 4

Front Panel ..............................................................................................................................4

Rear Panel................................................................................................................................ 4

Remote Control ....................................................................................................................... 5

Getting Started

Inserting Batteries Into the Remote Control............................................................................ 6

Hooking Up the System ..........................................................................................................6

Connecting Another CD Player...............................................................................................8

Playing CDs

Loading a CD .......................................................................................................................... 9

Playing the CD –– Normal Play/Shuffle Play/Repeat Play..................................................... 9

Using the CD display ............................................................................................................11

Replacing Discs While Playing a Disc..................................................................................12

Programming the CD tracks ..................................................................................................13

Fading In or Out ....................................................................................................................14

Recording From CDs

Recording a CD by Specifying Tape Length (Time Edit)..................................................... 14

Adjusting the Recording Level (Peak Search) ......................................................................15

Storing Information About CDs (Custom Files)

What You Can Do With the Custom Files ............................................................................16

Labeling Discs (Disc Name) .................................................................................................16

Using the Player with Another Component

Controlling Another CD Player (Advanced Mega Control) .................................................18

Playing Alternately (No-Delay Play/X-Fade Play) ..............................................................19

Additional Information

Using the CONTROL A1II control system...........................................................................20

Precautions ............................................................................................................................22

Notes on CDs.........................................................................................................................23

Troubleshooting.....................................................................................................................24

Specifications ........................................................................................................................24

FRUS

CHECK qh (13)

CLEAR qj (13, 14, 16, 17)

CONTINUE 2 (9, 13, 15, 18)

DISC 1–5 3 (9, 10, 13)

Disc compartment ws (9)

DISC SKIP 9 (9, 12, 13)

Display 4 (11)

EX-CHANGE 8 (12, 15)

FADER ql (14, 20)

MEGA CONTROL 0 (18, 19)

MENU wf (8, 16, 17)

PEAK SEARCH qk (15)

PHONES jack wh (10)

POWER 1 (7, 9, 16)

PROGRAM qd (9, 13, 18)

Remote sensor wa (6)

REPEAT qf (10, 18)

SHUFFLE qs (9, 10, 18)

TIME EDIT qg (14)

TIME/TEXT w; (11)

X-FADE/NO DELAY wg (19, 20)

Parts Identification

Front Panel

The items are arranged in alphabetical order.

Refer to the pages indicated in parentheses ( ) for details.

Rear Panel

2ND CD IN jacks 3 (8)

ANALOG OUT L/R jacks 4 (6)

CONTROL A1II jacks 1 (6, 20)

DIGITAL OUT OPTICAL jack 2 (7)

Mains lead 5 (6)

BUTTON DESCRIPTIONS

A OPEN/CLOSE wj (7, 9, 10, 11)

H 5 (9, 13, 15, 18, 20, 22)

X 6 (10, 15, 18, 22)

x 7 (10, 15, 18)

lAMSL (DISC) dial qa (10,

13, 15, 17, 18, 19)

m/M (AMS+/–) wd (10, 14, 17,

18)

Parts Identification

Remote Control

ANALOG OUT LEVEL +/– wh (6,

7, 10)

CD1/2/3 switch 1 (7)

CHECK 9 (13)

CLEAR ws (13, 14, 16, 17)

CONTINUE 3 (9, 13, 15, 18)

DISC/CAPS 6 (10, 17)

DISC SKIP +/– qh (9, 12, 13)

ENTER wa (17)

FADER/DEL w; (14, 20)

HIGH-LIGHT wd (12)

MEGA CONTROL 4 (18, 19)

MUSIC SCAN qa (10)

NAME INPUT qs (17)

NO DELAY ql (19, 20)

Number buttons 7 (10, 13, 17)

PROGRAM qj (9, 13, 18)

REPEAT 0 (10, 18)

SHUFFLE 2 (9, 10, 18)

TIME/TEXT/SPACE 5 (11, 17)

X-FADE qk (19, 20)

BUTTON DESCRIPTIONS

>10 8 (10, 13)

N wf (9, 13, 15, 18, 20, 22)

X qd (10, 15, 18, 22)

x wg (10, 15, 18)

./> qf (10, 13, 15, 17, 18,

19)

m/M qg (10, 14, 17, 18)

Getting Started

Inserting Batteries Into

the Remote Control

You can control the player using the supplied

remote.

Insert two R6 (size AA) batteries by matching

the + and – on the batteries to the diagram

inside the battery compartment.

Insert the negative (–) end first, then push in

and down until the positive (+) end clicks into

position.

When using the remote, point it at the remote

sensor

on the player.

Tip

When the remote no longer operates the system,

replace both batteries with new ones.

Note

• Do not leave the remote near an extremely hot or

humid place.

• Do not drop any foreign object into the remote

casing, particularly when replacing the batteries.

• Do not expose the remote sensor to direct sunlight

or lighting apparatuses. Doing so may cause a

malfunction.

• If you don’t use the remote for an extended period

of time, remove the batteries to avoid possible

damage from battery leakage and corrosion.

Hooking Up the System

Hookups

This section describes how to hook up the CD

player to an amplifier. Be sure to turn off the

power of each component before making the

connections.

Tips

• You can adjust the analog output level to the

amplifier using the remote comes with this player.

Press ANALOG OUT LEVEL +/– on the remote.

You can reduce the output level up to –20 dB.

When you reduce the analog output level, “FADE”

appears in the display.

• If you have a Sony component with the CONTROL

A1II jack, connect the component via the

CONTROL A1II jack. You can simplify the

operation of audio systems composed of separate

Sony components. For details, see “Using the

CONTROL A1II control system” on page 20.

CD player

Audio input

(White) (L)

: Signal flow

Amplifier

To mains

Audio input

(Red) (R)

ANALOG OUT

(Red) (R)

ANALOG OUT

(White) (L)

To mains

Getting Started

Making digital hookups

If you have a digital component such as a

digital amplifier, D/A converter, DAT, or MD,

connect the component via the DIGITAL OUT

(OPTICAL) connector using the optical cable

(not supplied). Take off the cap and plug in the

optical cable.

Note that you cannot use the following

functions when making this connection:

• Fading In or Out (see page 14)

• Adjusting the output level using the

ANALOG OUT LEVEL +/– buttons on the

remote

Note

When you connect via the DIGITAL OUT

(OPTICAL) connector, noise may occur when you

play CD software other than music, such as a CD-

ROM.

POC-15

Optical cable (not supplied)

Digital component

CD player

DIGITAL

OUT

OPTICAL

DIGITAL

INPUT

OPTICAL

When using another Sony CD player

in conjunction with this player

You can set the supplied remote to be effective

on this player only.

• If the other player’s command mode can be set:

Set the CD1/2/3 switch of this player’s remote to

CD1 (factory setting), and set the other player’s

remote to CD2 or CD3.

• If the other player’s command mode cannot be set:

Set the CD1/2/3 switch of this player’s remote to

CD2 or CD3.

When you change the command mode of the

remote, you have to set the command mode of each

player. For details, see “Changing the command

mode of the player” on page 8.

Transporting the player

Before transporting the player, follow the

procedure below to return the internal

mechanisms back to their original position.

1 Remove all the discs from the disc tray.

2 Press A OPEN/CLOSE to close the

disc tray.

“–NO DISC–” appears in the display.

3 Wait for 10 seconds, then press

POWER to turn off the player.

Connecting Another CD

Player

If you have a Sony CD player in which 5, 50,

200, 300, or 400 discs can be inserted and

which is equipped with the CONTROL A1II

(or CONTROL A1) jack and the command

mode of that player can be set to CD 3, you can

control that player as the second player with

this player. After connecting this player and an

amplifier, follow the procedure below.

Be sure to turn off the power of each player

before making this connection.

1 Connect the players with an audio cord

(see also “Hookups” on page 6).

2 Connect the players with a monaural

(2P) mini-plug cord.

For details on this connection, see “Using

the CONTROL A1II control system” on

page 20.

3 Set the command mode of this player

to CD1 (factory setting) or CD2, and set

that of the second player to CD3.

Check the display for the current command

mode of this player, if the mode is CD3,

you have to change the mode as described

below.

When the setting of both players is

complete, set the CD1/2/3 switches on each

remote accordingly.

For details on how to operate the second

player, see “Controlling Another CD

Player” on page 18 and “Playing

Alternately” on page 19.

Notes

• Do not connect a player other than that you use as

the second player to the 2ND CD IN jacks of this

player.

• When connecting a second CD player, do not

connect the DIGITAL OUT (OPTICAL) connector

of this player to the amplifier.

Changing the command mode

of the player

1 Press MENU.

2 Turn l AMS L to select

“COMMAND MODE.”

3 Push l AMS L.

The current command mode appears.

4 Turn l AMS L to select CD1 or

CD2, then push l AMS L again.

CDP-CE575

To ANALOG OUT

To 2ND CD IN

CDP-CX400, etc.

: Signal flow

To audio input

To audio output

Amplifier

CONTROL

A1II

Playing CDs

Playing the CD

––Normal Play/Shuffle Play/Repeat

Play

This unit lets you play the CD in different play

modes.

1 Select the play mode.

2 Press H.

Tips

• You can select the disc you want to start playing

first by pressing one of the DISC 1 – 5 buttons.

• You can specify discs during ALL DISCS Shuffle

Play mode, and the tracks on the specified discs are

played in a random order.

Press DISC 1 – 5 to specify the discs after Step 1.

Semi-circles appear around the specified disc

numbers in the display. To cancel the selected discs,

press DISC 1 – 5 again. The semi-circles disappear.

To return to ALL DISCS Shuffle Play, press

SHUFFLE until “ALL DISCS SHUFFLE” appears

in the display.

Loading a CD

1 Turn on the amplifier and select the CD

player position so that you can listen to

the sound from this player.

2 Press POWER to turn on the player.

3 Press AOPEN/CLOSE.

The disc compartment slides out.

4 Place a disc on the disc tray with the

label side up.

5 To place other discs, press DISC SKIP

and place the discs in the order you

want to play.

Each time you press the button, the disc tray

turns and you can place the discs in the

empty disc compartments. The player plays

the disc in front of you first.

6 Press AOPEN/CLOSE to close the disc

compartment.

Playing CDs

Disc number

When you play a CD

single, place it on the

inner circle of the tray.

continued

Getting Started

To play

All discs in the player

consecutively in the

order of disc number.

Only the disc you’ve

selected.

All tracks on all discs

in random order.

All tracks on the

specific disc in

random order.

The tracks on the CD

in the order you want

them to be played (see

“Programming the CD

tracks” on page 13).

Press

CONTINUE repeatedly

until “ALL DISCS”

appears.

CONTINUE repeatedly

until “1 DISC” appears.

SHUFFLE repeatedly

until ”ALL DISCS

SHUFFLE” appears.

SHUFFLE repeatedly

until ”1 DISC

SHUFFLE” appears.

PROGRAM.

Select a track directly

Go to the next disc

Select a disc directly

Find a point in a track

By scanning each track

for 10 seconds

(Music Scan)

Play tracks in random

order

Remove the CD

Adjust the volume

* When you directly locate a track numbered over 10,

press >10 first, then the corresponding number

buttons. To enter “0,” use button 10.

Example: To play track number 30

Press >10 first, then 3 and 10.

Tips

• You can adjust the analog output level with the

ANALOG OUT LEVEL +/– on the remote (page

6).

• You can adjust the headphones volume on the

remote. To adjust the volume, connect the

headphones to the PHONES jack and adjust the

volume with the ANALOG OUT LEVEL +/– on

the remote.

• If there is no CD in the player, “–NO DISC–”

appears in the display.

Notes

• If “OVER” appears in the display, the disc has

reached the end while you were pressing M. Press

m or turn lAMSL counterclockwise to go

back.

• If you press ANALOG OUT LEVEL +/– while

recording, the recording level will change even

when it is preset on the tape deck, etc.

Do this

Press the number button on

the remote.*

Press DISC SKIP.

Press DISC 1 – 5.

When using the remote,

follow the procedure below.

1 Press DISC.

2 Press the number button

of the disc.

3 Press ENTER.

Press and hold M or m

during playback, and

release at the desired point.

Press MUSIC SCAN. When

you find the track you want,

press H to start playing

the track. Each time you

press MUSIC SCAN, the

playing time changes

cyclically.

Press SHUFFLE until

“SHUFFLE” appears in the

display.

Press AOPEN/CLOSE.

Press ANALOG OUT

LEVEL +/– on the remote.

Repeat Play Operations

You can play the CD tracks repeatedly in any

play modes.

To activate the Repeat Play function, press

REPEAT until “REPEAT’ appears in the

display.

Repeat only one track

Cancel Repeat Play

When you are in the Repeat Play function, the

player repeats the tracks as follows:

When the disc is

played in

Continuous Play

(ALL DISCS)

Continuous Play

(1 DISC)

Shuffle Play

(ALL DISCS)

Shuffle Play

(1 DISC)

Program Play

(page 13)

Other Operations

Stop playback

Pause

Select a track

Press REPEAT

Until “REPEAT 1” appears

while playing the track you

want to repeat.

Until “REPEAT” or

“REPEAT1” disappears.

The player repeats

All the tracks on all discs

All the tracks on the current

disc

All the tracks on all discs in

random orders

All the tracks on the current

disc in random orders

The same program

Playing the CD (continued)

Do this

Press x.

Press X. Press X again or

H to resume play.

During play or pause, turn

lAMSL clockwise

(to go forward) or

counterclockwise (to go

backward) (or press >(

to go forward) or . (to

go backward) on the

remote).

Playing CDs

Using the CD display

You can check information about the disc using

the display.

In the stop mode

Press TIME/TEXT.

The display shows the current disc number, the

total number of tracks, total playing time, and

music calendar.

The information also appears when you press

AOPEN/CLOSE to close the disc tray.

Notes on the disc number

indications

• The red circle around a disc number

indicates the disc is ready to be played.

• When all the tracks on a disc have been

played, the semi-circle around the disc

number disappears.

• When a disc compartment is recognized as

empty, the semi-circled disc number

disappears.

During normal playback

While playing a disc, the display shows the

current disc number, track number, playing

time of the track and the music calendar.

The track numbers in the music calendar

disappear after they are played.

Total number of tracks

Music calendar

Total playing time

Current disc number

To check the remaining time

Press TIME/TEXT during playback.

Each time you press this button while playing a

disc, the display changes as shown in the chart

below.

Playing time on the current track t

Remaining time on the current track t

Remaining time on the disc

Note

In Program Play mode,the remaining time on the disc

does not appear.

While playing a CD TEXT disc

CD TEXT discs have information, such as the

disc titles or artist names, memorized in a blank

space on the discs where, on normal discs,

there is no information. The display shows the

CD TEXT information of the disc so that you

can check the current disc title, artist name, and

track title. When the player detects CD TEXT

discs, the “CD TEXT” indication appears in the

display.

In the Stop Mode

Press TIME/TEXT.

Each time you press this button, the display

changes as shown in the chart below.

Disc title t Artist name t Total number of

tracks and total playing time

During normal playback

Press TIME/TEXT.

Each time you press this button, the display

changes as shown in the chart below.

Track title t Playing time on the current disc

t Remaining time on the current track t

Remaining time on the disc

If a title or name has more than 12 characters,

the first 12 characters will light up after the title

or name scrolls by in the display.

continued

12345

678910

12345

DISCSALL

DISC

TRACK

MIN SEC

CD1

1 1O 45.28

Replacing Discs While

Playing a Disc

You can open the disc tray while playing a disc

so that you can check what discs are to be

played next and replace discs without

interrupting playback of the current disc.

1 Press EX-CHANGE.

The disc tray opens and two disc

compartments appear. Even if the player is

playing a disc, it doesn’t stop playing.

2 Replace discs in the compartments

with new ones.

The player plays the disc on the left side

compartment after the current disc, and then

the one on the right side compartment.

3 Press DISC SKIP.

The disc tray turns and other two disc

compartments appear.

4 Replace discs in the compartments

with new ones.

5 Press EX-CHANGE.

The disc tray closes.

While the disc tray is open by

pressing the EX-CHANGE button

• If the playback of the current disc ends, the

player stops playing. If the disc is played in

1 DISC Repeat Play mode (see page 10), the

current disc starts playing again.

• In ALL DISCS Shuffle Play mode (see page

9), tracks are reshuffled on the current disc.

• In Program Play mode (see page 13), only

the tracks on the current disc are played.

• Do not push the disc tray to close it in

Step 5, as you may damage the

player.

Tip

Some CD TEXT discs have a feature to play only the

highlights of the discs.

Press HIGH-LIGHT on the remote to start playing

disc highlights in the stop mode.

“HIGH LIGHT” appears momentaly in the display

while playing disc highlights.

Notes

• The display may not show all the characters

depending on the disc.

• This player can only display the disc titles, track

titles and artist names from CD TEXT discs. Other

information cannot be displayed.

Using the CD display (continued)

Playing CDs

Programming the CD

tracks

You can arrange the order of the tracks on the

discs and create your own program. The

program can contain up to 32 “steps” — one

“step” may contain a track or a whole disc.

1 Press PROGRAM so that “PROGRAM”

appears in the display before you start

playing.

If a program is already stored, the last step

of the program appears in the display. When

you want to erase the whole program, hold

down CLEAR until “CLEAR” appears in

the display (see page 14).

2 Press DISC 1 – 5 to select the disc.

“AL” in the display stands for “all” tracks.

When you want to program the whole disc

as one step, skip Step 3, and go to Step 4.

3 Turn lAMSL until the track you

want appears and push lAMSL to

select the track.

The track number that you programmed, the

playing order, and the total playing time

appear in the display.

If you’ve made a mistake

Press CLEAR, then repeat Step 3.

Tip

You can select the track using the number buttons

on the remote. To select a track with a number

over 10, use >10 (see page 10).

4 To program other discs or tracks, do

the following:

5 Press H to start Program Play.

To program

Other discs

Other tracks on the

same disc

Other tracks on

other discs

Repeat Step(s)

2 and 3

To cancel Program Play

Press CONTINUE.

Tips

• You can create your program while checking the

disc labels.

While the disc tray is open, follow Steps 1 to 4 with

pressing the DISC SKIP button to check the disc

labels. If you close the disc tray before Step 5, the

total playing time appears in the display after a

while.

Note that, if the programmed track number isn’t

found on the disc, that step is automatically erased.

• The program remains even after the Program Play

ends. When you press the H button, you can play

the same program again.

• The program remains until you erase it. If you

replace discs, the programmed disc and track

numbers remain. So, the player plays only the

existing disc and track numbers. However, the disc

and track numbers that aren’t found in the player or

on the disc are deleted from the program, and the

rest of the program is played in the programmed

order.

• For the recording to the A side or B side of the

cassette tape, you can pause Program Play.

Note

The total playing time doesn’t appear when:

—You have programmed a track whose number

exceeds 20.

—The total playing time of the program exceeds 200

minutes.

Checking the track order

You can check your program before or after

you start playing.

Press CHECK.

Each time you press this button, the display

shows the track (the disc and track numbers) or

the disc (the disc number and “AL” indication)

of each step in the programmed order. After the

last step in the program, the display shows “–

END –” and returns to the original display. If

you check the order after you start playing, the

display shows only the remaining steps.

continued

Recording a CD by

Specifying Tape Length

(Time Edit)

You can have the player create a program that

will fit the length of the tape.

The player automatically creates a program,

keeping the original order of the disc.

The program can contain up to 32 steps (a

pause inserted between steps is counted as one

step).

Note that tracks numbered over 20 cannot be

programmed automatically.

1 Press DISC SKIP to select the disc.

2 Press TIME EDIT repeatedly before you

start playing until “EDIT” appears and

“A” in the indication flashes in the

display.

3 Press m or M to specify the tape

length.

Each time you press these buttons, the

display changes as shown below, with the

tape length of one side following each

indication.

4 Press TIME EDIT to have the player

create the program.

The display shows the tracks to be recorded.

“B” in the indication flashes in the

display.

5 When you record on both sides of the

tape, press TIME EDIT again.

The player inserts a pause, then creates the

program for side B. The display shows the

programmed tracks.

When you record on one side of the tape,

skip this step.

Press FADER

During pause. “FADE” flashes.

The play fades in.

When you want to start fading

out. “FADE” flashes. Then play

fades out and the player pauses.

Recording From CDs

Changing the track order

You can change your program before you start

playing.

Erase a track

Erase the last track

in the program

Add tracks to the

end of the

program

Change the whole

program

completely

Fading In or Out

You can manually fade in or out to prevent

tracks from starting or ending abruptly.

Note that you cannot use this effect when you

use the DIGITAL OUT (OPTICAL) connector.

Start play fading in

End play fading out

Fading time lasts for 5 seconds.

You need to

Press CHECK until the track you

don’t want appears in the display,

then press CLEAR.

Press CLEAR. Each time you

press the button, the last track will

be cleared.

Follow Steps 2 through 4 of the

programming procedure.

Hold down CLEAR until

“CLEAR” appears in the display.

Create a new program following

the programming procedure.

Creating your own program

(continued)

C-54 27.00C-46 23.00 C-60 30.00

- -. - - C-90 45.00

C-74 37.00

Playing CDs

6 Start recording on the deck and then

press H on the player.

7 Reverse the tape to side B and press

H or X on the player to resume

playing the remaining tracks.

To cancel Time Edit

Press CONTINUE.

Tips

• You can program the tracks you want in advance.

Create a program selecting the desired tracks, then

follow Steps 2 to 7. Be careful that the total playing

time of the program does not exceed the tape length

of one side.

• You can set the tape length freely using

l AMS L.

Example:When the tape length of one side is 30

minutes and 15 seconds

1 To set the minutes, turn l AMS

L until “30” appears in the display,

then push l AMS L.

2 To set the seconds, turn l AMS

L until “15” appears in the display,

then push l AMS L.

• To check and change your program, see pages 13

and 14.

Recording From CDs

Adjusting the Recording

Level (Peak Search)

The player locates the highest level among the

tracks to be recorded to let you adjust the

recording level before you start recording.

1 Before you start playing, press PEAK

SEARCH.

“PEAK” flashes in the display and the

player starts scanning the disc searching for

the highest peak level.

After scanning all the tracks, the player

repeats the portion with the highest peak

level.

2 Adjust the recording level on the deck.

3 Press x on the player to stop Peak

Search.

“PEAK” disappears from the display.

Notes

• The portion with the highest level may differ every

time you try the adjustment on the same disc. The

difference is, however, so slight that you won’t

find any problem in adjusting the recording level

precisely.

• Peak Search does not operate while you open the

disc tray by pressing the EX-CHANGE button.

Storing Information About CDs (Custom Files)

What You Can Do With the

Custom Files

The player can store the information called

“Custom Files” for each disc. By using this

function, you can label discs using up to 12

characters.

Once you have stored Custom Files for a disc,

the player automatically recalls what you have

stored whenever you select the disc. Note that

Custom Files will be erased if you do not use

the player for about one month.

Where are Custom Files stored?

Custom Files are stored not on the disc, but in

the player’s memory. It means you cannot use

Custom Files when you play the disc on other

players.

Erasing all Custom Files of all discs

Turn off the player. While holding down

CLEAR, press POWER to turn on the player.

“ALL ERASE” appears in the display, and all

Custom Files will be erased.

Labeling Discs

(Disc Name)

You can label discs using up to 12 characters

and have the player display the Disc Name

each time you select the disc. The Disc Name

can be anything you like, such as a title,

musician’s name, category or date of purchase.

Tip

When you select a CD TEXT disc, the disc title is

stored as the Disc Name automatically.

If the disc title has more than 12 characters, the first

12 characters of the disc title are stored.

Note that you cannot change the Disc Name of the

CD TEXT disc.

Labeling discs on the player

1 Insert or select the disc.

2 Press MENU.

“DISC NAME” flashes in the display.

3 Push l AMS L.

“NAME INPUT” appears, then the flashing

cursor ( ) appears.

4 Turn l AMS L until the character

you want appears in the display.

The cursor disappears and the first space for

the Disc Name flashes.

As you turn l AMS L clockwise, the

characters appear in the following order.

Turn l AMS L counterclockwise to

go back to the previous character.

(space) A B C D E F G H I J K L M N O

P Q R S T U V W X Y Z a b c d e f g h i j

k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6

7 8 9 ! “ # $ % & ’ ( ) * + , – . / : ; < = > ?

@ _

Storing Information

About CDs (Custom Files)

4 Press CAPS to find the letter type you

want.

Each time you press the button, the letter

type changes cyclically among capital

letters (ABC), small letters (abc) and

numbers (123). To select a symbol, you

have to select the capital or small letter

type.

5 To input a letter, press the number

button corresponding to the letter you

want (indicated beside each number

button).

Each time you press the button, the letter

changes cyclically among the ones indicated

beside the button.

To input symbols, press the number button

1 repeatedly until the symbol you want

appears in the display.

To insert a space, press SPACE once.

To input a number, press the number button

you want.

6 Press M to select the character.

The selected character lights up, and the

flashing cursor appears to indicate the next

space to be input.

You can also go to the next space by

pressing other number buttons.

7 Repeat Steps 4 through 6 to input more

characters.

8 Press NAME INPUT to store the Disc

Name.

Repeat Steps 1 through 8 to assign Disc

Names to other discs.

Erasing the Disc Name

1 Follow Steps 1 and 3 in “Labeling discs

on the player” on page 16 to select the

Disc Name you want to erase.

2 Press CLEAR repeatedly until all the

characters disappear.

3 Press MENU.

5 Push l AMS L to select the

character.

The selected character lights up, and the

flashing cursor appears to indicate the next

space to be input.

To insert a space

Press M.

If you have made a mistake

Press m/M to flash the incorrect character,

then input the correct character.

6 Repeat Steps 4 and 5 to input more

characters.

7 Press MENU to store the Disc Name.

Repeat Steps 1 to 7 to assign Disc Names to

other discs.

If you have made a mistake while

inputting the character

To correct the character which has been

input

1 Press m or M until the incorrect character

flashes.

2 Turn l AMS L until the desired character

appears.

To correct the character currently being

input

1 Press CLEAR to delete the incorrect character.

2 Input the correct character.

To insert a character between the input

characters

Press m or M until the cursor moves to the former

of the two characters, then press ENTER and input

the correct character.

Labeling discs using the

remote

1 Press DISC in Continuous Play Mode.

2 Press the number button of the disc

you want to assign a Disc Name, and

then ENTER.

3 Press NAME INPUT.

The flashing cursor ( ) appears.

Controlling Another CD

Player (Advanced Mega

Control)

This unit can control a second CD player (see

“Connecting Another CD Player” on pages 8).

Even when a second CD player is connected,

the controls on both of the units will function.

When you press the play button on either unit,

the operating player stops and the resting

player starts.

Note that depending on the player, you may not

be able to operate all the functions of the

second CD player.

The controls as described below are effective

while the MEGA CONTROL button is lit:

CONTINUE, SHUFFLE, PROGRAM,

REPEAT, MENU, MEGA CONTROL,

l AMS L, H, X, x, m/M

Playing discs of the second

CD player

1 Press MEGA CONTROL.

The MEGA CONTROL button lights up

and the display shows the current disc

number of the second player.

2 Select the play mode you want.

To program tracks, use the controls on the

second player.

3 Press H to start playing.

The play starts and the display shows the

current disc and track numbers and the

playing time of the track.

While the MEGA CONTROL button is lit,

you can control the second player with the

controls on this player as follows:

Pause

Stop play

Locate a disc while

the second player is

set to Continuous

Play mode

Locate a track

• To do other operations, use the controls on the

second player or the supplied remote.

• The AMS buttons (./>) and search buttons

(m/M) on the remote operate the second player

as indicated on the remote.

To control the second player directly

using the supplied remote

Set CD 1/2/3 on the remote to CD 3, which is

the same mode set for the second player.

To control this player again

Press MEGA CONTROL. The MEGA

CONTROL button goes off and you can

control this player.

Notes

• You cannot locate a particular point in a track of the

second player using the controls on this player.

• Some controls on this player work on the second

player differently from they do to this player.

Loading the Disc Names

(Disc Memos) of the second

CD player

If the second CD player has the Disc Name

(Disc Memo) function (see page 16), you can

load the Disc Name (Disc Memo) of the second

CD player to this player’s memory and display

them on this player.

1 Press MENU.

2 Turn l AMS L until “LOAD

2ndNAME” appears in the display.

3 Push l AMS L.

This player starts loading. (Loading takes

about one minute.)

Using the Player with Another Component

You need to

Press X.

Press x.

Turn l AMS L until the

display shows the disc number

you want, then push

l AMS L.

Press m/M until the display

shows the track number you

want.

Storing Information

About CDs (Custom Files)

Note

If each Disc Name (Disc Memo) of the second CD

player has more than 12 characters, the first 12

characters of each are loaded to this player.

Labeling discs of the second

CD player

You can label discs of the second CD player or

change the Disc Names (Disc Memos) loaded

from the second CD player.

1 Press MEGA CONTROL.

The MEGA CONTROL button lights up.

2 Press CONTINUE.

3 Turn l AMS L to select the disc

you want, then push l AMS L.

4 Press MENU.

5 Turn l AMS L until “DISC NAME”

appears in the display, then push

l AMS L.

6 Input the new Disc Name (Disc Memo)

following the procedure in “Labeling

Discs” on page 16.

Note

The new Disc Names (Disc Memos) are stored on this

player’s memory, so you cannot display them on the

second CD player.

Playing Alternately

(No-Delay Play/X-Fade

Play)

When you connect the second player, you can

play tracks in this player and those in the

second player alternately in any play mode (see

“Connecting Another CD Player” on page 8).

Select one of the following methods:

• No-Delay Play: The current player changes at

each track. Each time the current player changes to

the other player, the other player starts play without

a break in sound immediately after the current

player ends play. The other player skips the lead-in

portion and starts playing from where the sound

actually begins.

• X-Fade Play: The current player changes at each

track or at the specified interval. You can select the

interval among 30, 60 and 90 seconds. Each time

the current player changes to the other player, the

sound from both players is mixed. The current

player ends play by fading out, and the other player

starts play by fading in.

1 Select the play mode you want on each

player.

2 When you select No-Delay Play

Press X-FADE/NO DELAY repeatedly

until “NO DELAY” appears in the display

(or press NO DELAY on the remote).

When you select X-Fade Play

Press X-FADE/NO DELAY or X-FADE on

the remote.

Each time you press X-FADE/NO DELAY,

the indication (X-Fade mode) appears as

follows:

Each time you press X-FADE on the

remote, the indication (X-Fade mode)

appears as follows:

X-FADE 30SNO DELAY X-FADE 60S

X-FADE ALL

OFF

X-FADE 90S

continued

after 30 secat track end after 60 sec

X-FADE off

after 90 sec

Note

“NO DELAY” does not appear when you operate

from the remote.

To change the current player each time a

whole track is finished, select “X-FADE

ALL.”

To change the current player at the specified

interval, press X-FADE/NO DELAY

repeatedly until the interval you want

appears in the display.

3 Press H to start playing.

The MEGA CONTROL button lights up

while the track in the second player is

selected.

To check the X-Fade mode status

Press X-FADE/NO DELAY once.

The X-Fade mode status appears momentarily.

To cancel No-Delay/X-Fade Play

Press X-FADE/NO DELAY repeatedly until

“X-FADE” or “NO DELAY” goes off. The

current player continues playing.

Tips

• you can change the method (No-Delay or X-Fade)

during play when you press X-FADE/NO DELAY

in Step 2.

• When you press FADER during X-Fade Play, you

can start X-Fade whenever you like.

Even after you have set the X-Fade mode and

started X-Fade Play, you can start X-Fade manually

at the point you like. Note that you cannot do this

operation while the sound from both players is

mixed.

Notes

• The play starts from the second player if you start

play while the MEGA CONTROL button is lit.

• When either player has played all its discs/tracks,

both players stop, even if the other player has not

finished yet.

• Do not use the controls on the second player during

No-Delay Play/X-Fade Play. They may not work

correctly.

Playing Alternately (No-Delay Play/X-

Fade Play) (continued)

Using the CONTROL A1II

control system

This player is compatible with the CONTROL

A1II Control System.

The CONTROL A1II control system was

designed to simplify the operation of audio

systems composed of separate Sony

components. CONTROL A1II connections

provide a path for the transmission of control

signals that enable automatic operation and

control features usually associated with

integrated systems.

Currently, CONTROL A1II connections

between a Sony MD deck, CD player, amplifier

(receiver), and cassette deck provide automatic

function selection and synchronized recording.

In the future the CONTROL A1II connection

will work as a multifunction bus allowing you

to control various functions for each

component.

Note

The CONTROL A1II control system is designed to

maintain upward compatibility as the control system

is upgraded to handle new functions. In this case,

however, older components will not be compatible

with the new functions.

Additional Information

La page charge ...

Sony CDP-CE575 Le manuel du propriétaire

Marque: Sony

Modèle: CDP-CE575

Catégorie: Lecteur CD

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Sony CDP-CE575 Owner's manual

Sony CDP-CE575 Le manuel du propriétaire

Sony CDP-CE575 Le manuel du propriétaire

dans d''autres langues

Documents connexes