wattstopper STPERW201 Guide d'installation

Marque: wattstopper

Modèle: STPERW201

Taper: Guide d'installation

Ce manuel convient également à

IS-0625 – Rev. 2

36V stations have a symbol on the Serial Number

sticker. Any station, not displaying this symbol, ,

should not be connected to a 36Volt Station Bus.

The Power Station Booster is a single load dimmer station able to handle a larger than normal 1oad.

The station installs in a 2-gang wall-box or in Wattstopper’s LCAP series enclosures. Faceplate

covers are available in Almond, Black, Brown, Ivory and White for 2-gang wall-box enclosures.

Wattstopper/Vantage

Power Station Booster

Installation Instructions

IS-0625 Rev. 2

STPSRW101 (201) / STPERW101 (201)

Country of Origin: Made in China

OVERVIEW

SPECIFICATIONS

Description Specication

Dimensions, HWD 4.34” x 4.25” x 2.5” (110.2mm x 107.9mm x 63.5mm)

Dimensions, Faceplate 4.75” square (120.6mm square)

Weight 14.4oz. (407g)

Voltage See Load Specications table

Load Types See Load Specications table

Number of Loads 1

Status Indicator Microprocessor Status

Station Wiring Conguration Daisy-chain / Star / Branch

*Station Bus Connection 24V / 36V Station Bus

Station Bus Wiring 2 Conductor, 16AWG / 1.31mm2, twisted, non-shielded, <30pF per foot.

Separate a minimum of 12” / 30.5cm from other parallel communication

and/or high-voltage runs

Station Equivalent InFusion 0.35W on IC-24 / 0.55W on IC-36

Station Equivalent QLink 1 Station

Cooling Convection

Ambient Operating Temperature 32 - 95°F ( 0 - 35°C)

Ambient Operating Humidity 5 - 95% non-condensing

UL and CUL Listed Yes

CAUTION

SYSTEM REQUIREMENTS

All four station types are compatible with InFusion Systems. For new projects it is recommended that rmware and software be kept

to the most current release.

IS-0625 – Rev. 2

LOAD SPECIFICATIONS

INSTALLATION

Standard Dimmer Electronic Dimmer

Model

STPSRW101 STPSRW201 STPERW101 STPERW201

Load Types

Forward Phase Only - Minimum Load 15W Reverse Phase Only - Minimum Load 5W

Incandescent

Magnetic low-voltage*

LED

Incandescent

Magnetic low-voltage*

LED

Incandescent

Electronic lighting*

LED

Incandescent

Electronic lighting*

LED

Voltage/Frequency 120VAC, 50/60Hz 220-277VAC, 50/60Hz 120VAC, 50/60Hz 220-277VAC, 50/60Hz

Maximum Standard Load 16A, 1920W@120V 16A, 3520W@220V

16A, 4432W@277V

8A, 960W@120V 4.5A, 990W@220V

3.5A, 90W@277V

Maximum *MLV Load 1000VA @ 120V 2000V A@2 77V NA NA

Maximum LED Load

(see LED Dimming)

3.2AMP, 384W@120V 3.2A, 704W@220V

3.2A, 886.4W@277V

4.8A, 576W@120V 2.7A, 594W@220V

2.1A, 582W@277V

Installation of these products should be performed or supervised by a Certied Installer. Turn the circuit breaker off and make sure no

voltage is present before installing the Power Station Dimmer. Damage caused by failure to disconnect power may void warranty and

is a risk to the installer. Connect control wires for Station Bus stand-alone control or the ScenePoint dimmer station scenario. Connect

the wires as shown in the diagram (Black to LINE, White to NEUTRAL, Red to LOAD, Green to structure’s safety GROUND). Before

turning the circuit breaker on, check to see that all connections are correct (In particular, check to see that the correct wires have

been connected to “Line In” and “Load Out”).

The booster station may be controlled using one of the two installation congurations below. NOTE: Never connect using both

methods in the same installation.

1. As a stand alone dimmer: The booster is connected to and controlled through the Station Bus, acting as a stand alone, high

power, single station dimmer. -OR-

2. As a power booster for a ScenePoint Dimmer Station, Module Load, or LMRC-22x: The dimmed output from a dimmer station

or dimmer module is connected to the booster and acts as a control line. A separate line feed is attached to the booster and the load

is connected to the output. In short, the dimmer station or dimmer module controls the dim level, while the booster handles the power.

NOTE: Only connect one Power Station Booster to a dimmed load, using this method.

To reduce the risk of overheating and possible damage to other equipment, do not install to control a

receptacle. Any motor or appliance connected to a Power Station Booster requiring “RELAY MODE” must be programmed to relay

mode through software rst. The Power Station is shipped in “DIMMING MODE”. To change the default mode to RELAY change the

Power Prole to Relay in the Software. The Relay Mode change will not take place until the Power Station is on line and the system

is programmed.

With this station’s dimensions most standard back boxes that have the receiving threads for the station mounting screw inside the

box will be adequate. Most back boxes where the receiving threads are outside the box will be too small. Test back boxes for proper

t before installing.

BACK BOX / MUD RING DIMENSIONS

With this station’s dimensions most standard back boxes that have the receiving threads for the station mounting screw inside the

box will be adequate. Most back boxes where the receiving threads are outside the box will be too small. Test back boxes for proper

t before installing. If mud rings are specied on a job it is important to test the mud rings for proper t. Two gang mud rings, in

particular, run substantially smaller than back boxes and some brands are not large enough for the station. The only solution is to test

the t rst.

DEFAULT MODE

The Power Station has a default mode that operates without programming or being connected to the InFusion System. If the Power

Station has been programmed but communication with the controller is lost the station will revert to default operation. The button on

the front of the station acts as follows (see next page):

Back Box Minimum Back Box Dimension

2-Gang Back Box 2.80”h x 3.60”w x 2.5”d

CAUTION

IS-0625 – Rev. 2

First select the room, then click on Vantage Objects in the Object Explorer and expand Stations, WireLink. From the list of

stations double click on the Power Station to place it in the room. In the Object Editor name the station, select the correct model and

make sure it is on the correct Station Bus port.

CONFIGURING

If using the conguration install method number “2” above, the station should not be congured. For method “1” above, the serial

number may be manually typed in the project le. Traditional conguration: When the Power Station is rst connected to the

Station Bus, the diagnostic LED will blink twice followed by a pause. This means the Power Station is connected correctly but is not

congured. It is congured like any other station. From Design Center, click on the Congure Stations button on the toolbar. To nish,

press the congure button on the front of the station. Once congured the diagnostic LED will blink evenly.

DIAGNOSTIC INFORMATION

The Diagnostic LED blinks 1 time evenly or 2, 3, 4, or 5 blinks followed by a pause.

One Even Blink: The Power Station is operating correctly and is congured.

Two Blinks: The Power Station is operating correctly but is not congured.

Three Blinks: The Power Station is not communicating with the Main Controller. Check the Station Bus connection.

Four Blinks: Factory problem. Please contact the factory.

Five Blinks: The Power Station is waiting to be congured.

PROPER TORQUE and WIRE

RESET

The power booster station operates as a standalone or as a high power load on the system. To reset, turn OFF power to LINE. With

the power OFF, hold in the Congure/Toggle button on the front while power is restored to LINE. Continue holding the button in for

about two (2) seconds to make sure the station reset happens.

NOTE: If the Station Load was changed to RELAY this Process will change it back to DIM. Make sure it is back on line with the Main

Controller before testing button or load operation.

DEFAULT BUTTON OPERATION

Action Load Operation

Single Press The load toggles between off and the learned level. The turn on ramp

time is 1.5 seconds and the turn off fade time is 5 seconds.

Double Press The load ramps to 100% in 1.5 seconds. The second press must be

within 1 second of the rst press.

Press and Hold After a one second delay the load will ramp in the opposite direction

from the last press and hold. If the load reaches 0 or 100% it will reverse

direction. When the button is released the current load level will be saved

as the new learned level for that button. The cycle time is 5 seconds from

0-100%.

Relay Mode The load turns on with the rst press and release and OFF with the

second press and release.

SETUP IN DESIGN CENTER

Connector Torque Wire Range

LINE/LOAD WIRING 20 INCH POUNDS 14-10 AWG (Must match breaker wire gauge)

LED DIMMING

• Legrand is leading the way in LED lighting control through innovations of new hardware and software products;

however, industry standards are still undened for dimming LED lamps and xtures. Dimming performance of

LED lighting cannot be guaranteed, even when applying the correct dimming technology specied by the LED

manufacturer. While Legrand may be consulted when performance issues are present, Legrand will not be liable for

on-site performance issues.

• There are many factors that may contribute to unsatisfactory results within a specic installation, including, but not

limited to:

- Line noise originating from electrical equipment within the premises

- Line noise from the source (particularly with local generators or inverters)

- Interference between dimmed LED products

- Wiring conditions (i.e. shared neutrals, loose neutrals, incorrectly bonded neutral, or grounding issues)

- LED product variances, including:

• Unintended batch-related variances

• Product revisions

800.555.9891

www.legrand.us/wattstopper

IS-0625 – Rev. 2

Wattstopper warranties its products to be free

of defects in materials and workmanship for a

period of five (5) years. There are no obligations

or liabilities on the part of Wattstopper for

consequential damages arising out of, or in

connection with, the use or performance of this

product or other indirect damages with respect

to loss of property, revenue or profit, or cost of

removal, installation or reinstallation.

Wattstopper garantit que ses produits sont

exempts de défauts de matériaux et de fabrication

pour une période de cinq (5) ans. Wattstopper

ne peut être tenu responsable de tout dommage

consécutif causé par ou lié à l’utilisation ou

à la performance de ce produit ou tout autre

dommage indirect lié à la perte de propriété, de

revenus, ou de profits, ou aux coûts d’enlèvement,

d’installation ou de réinstallation.

Wattstopper garantiza que sus productos

están libres de defectos en materiales y mano

de obra por un período de cinco (5) años. No

existen obligaciones ni responsabilidades por

parte de Wattstopper por daños consecuentes

que se deriven o estén relacionados con el

uso o el rendimiento de este producto u otros

daños indirectos con respecto a la pérdida

de propiedad, renta o ganancias, o al costo

de extracción, instalación o reinstalación.

WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA

MULTI-VIEW LINE DRAWING

WIRING

LINE / HOT

LOAD

DIM

CONTROL

NEUTRAL

CAUTION:

USE COPPER WIRE ONLY RATED FOR AT LEAST 75°C

WARNING:

TURN OFF POWER BEFORE MAKING SUPPLY CONNECTIONS

CLASS 2

GND - Green Wire

Station

Bus

Control Option 1

Standalone Station Bus

Control Option 2

ScenePoint Dimmer Station/Module/

LMRC-22x

(neutral from dimmer station not needed)

LOAD and NEUTRAL

to Fixture

LINE and NEUTRAL

From Breaker

FRONT VIEW SIDE VIEW BACK VIEW

Configure and

Toggle Button

Status LED

LINE / HOT

LOAD

DIM

CONTROL

NEUTRAL

CAUTION:

USE COPPER WIRE ONLY RATED FOR AT LEAST 75°C

WARNING:

TURN OFF POWER BEFORE MAKING SUPPLY CONNECTIONS

CLASS 2

GND - Green Wire

Station

Bus

4.34"

4.25"

4.75"

1.625"

2.5"

0.875”

wattstopper STPERW201 Guide d'installation

Marque: wattstopper

Modèle: STPERW201

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: wattstopper STPERW201 Installation guide

wattstopper STPERW201 Guide d'installation

Ce manuel convient également à

wattstopper STPERW201 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents