ESAB Plasma Welding Power Supply Manuel utilisateur

Marque: ESAB

Modèle: Plasma Welding Power Supply

Catégorie: Système de soudage

Taper: Manuel utilisateur

Operating Manual

October 4, 2002 Manual No. 0-2472

Plasma Welding

Power Supply

Ultima 150

WARNINGS

Read and understand this entire Operating Manual and your employer’s safety practices before install-

ing, operating, or servicing the equipment.

While the information contained in this operators manual represents our best judgement, Thermal

Dynamics Corporation assumes no liability for its use.

ULTIMA-150 Plasma Welding Operating Manual

Number 0-2472

Published by:

Thermal Dynamics Corporation

82 Benning Street

West Lebanon, New Hampshire, USA 03784

(603) 298-5711

www.thermal-dynamics.com

Thermal Dynamics Corporation

Reproduction of this work, in whole or in part, without written permission of

the publisher is prohibited.

The publisher does not assume and hereby disclaims any liability to any

party for any loss or damage caused by any error or omission in this manual,

whether such error results from negligence, accident, or any other cause.

Printed in the United States of America

Publication Date: October 4, 2002

Record the following information for Warranty purposes:

Where Purchased:_______________________________

Purchase Date:__________________________________

Power Supply Serial #:___________________________

Torch Serial #:__________________________________

TABLE OF CONTENTS

SECTION 1: INTRODUCTION.................................................................................................... 1

1.01 Notes, Cautions and Warnings....................................................................... 1

1.02 Important Safety Precautions ........................................................................ 1

1.03 Publications.................................................................................................... 2

1.04 Note, Attention et Avertissement ................................................................... 3

1.05 Precautions De Securite Importantes ............................................................ 3

1.06 Documents De Reference.............................................................................. 5

1.07 Declaration of Conformity .............................................................................. 6

1.08 Statement of Warranty ................................................................................... 7

SECTION 2: GENERAL INFORMATION .................................................................................... 9

2.01 Scope of this Manual ..................................................................................... 9

2.02 ULTIMA-150 Power Supply Description ......................................................... 9

2.03 ULTIMA-150 Power Supply Specifications ..................................................... 9

2.04 The ULTIMA-150 System............................................................................. 10

2.05 Requirements to Complete System ............................................................. 10

2.06 Options, Accessories, and Replacement Parts............................................ 10

2.07 Introduction to Plasma Arc Welding ............................................................. 10

2.08 Theory of Operation ..................................................................................... 11

SECTION 3: INSTALLATION..................................................................................................... 13

3.01 Introduction .................................................................................................. 13

3.02 Site Location ................................................................................................ 13

3.03 Unpacking .................................................................................................... 13

3.04 Primary Input Power Connections................................................................ 13

3.05 Voltage Changeover ..................................................................................... 15

3.06 Work Cable Connection ............................................................................... 16

3.07 Plasma and Shield Gas Connections........................................................... 16

3.08 Torch Connection ......................................................................................... 17

3.09 Remote Connections ................................................................................... 17

3.10 Filling Coolant Reservoir .............................................................................. 17

SECTION 4: OPERATION ........................................................................................................ 19

4.01 Introduction .................................................................................................. 19

4.02 Operating Controls and Indicators ............................................................... 19

4.03 Basic Operation ........................................................................................... 21

4.04 Torch Operation............................................................................................ 22

SECTION 5: GENERAL MAINTENANCE ................................................................................. 23

5.01 Introduction .................................................................................................. 23

5.02 General Maintenance................................................................................... 23

5.03 Basic Troubleshooting .................................................................................. 25

5.04 Basic Parts Replacement............................................................................. 28

TABLE OF CONTENTS (continued)

SECTION 6: PARTS REPLACEMENT ...................................................................................... 31

6.01 Introduction .................................................................................................. 31

6.02 Returns ........................................................................................................ 31

6.03 Ordering Information .................................................................................... 31

6.04 Complete Systems....................................................................................... 31

6.05 Power Supply Only....................................................................................... 32

6.06 Replacement Torches .................................................................................. 32

6.07 Options and Accessories ............................................................................. 33

APPENDIX I: CIRCUIT PROTECTION & WIRING ................................................................... 35

APPENDIX II: QUICK DISCONNECT LEADS ASSIGNMENT ................................................. 36

APPENDIX III: REMOTE WIRING ............................................................................................ 37

APPENDIX IV: OPERATIONAL FLOWCHART ......................................................................... 38

APPENDIX V: HOSE DIAGRAM ............................................................................................... 39

APPENDIX VI: TORCH PARTS................................................................................................. 40

APPENDIX VII: TORCH PARTS TABLE .................................................................................... 41

APPENDIX VIII: SCHEMATIC DIAGRAM ................................................................................. 42

APPENDIX VIII: SCHEMATIC DIAGRAM ................................................................................. 43

Date: November 15, 2001 1 GENERAL INFORMATION

SECTION 1:

GENERAL INFORMATION

1.01 Notes, Cautions and Warnings

Throughout this manual, notes, cautions, and warnings

are used to highlight important information. These high-

lights are categorized as follows:

NOTE

An operation, procedure, or background informa-

tion which requires additional emphasis or is help-

ful in efficient operation of the system.

CAUTION

A procedure which, if not properly followed, may

cause damage to the equipment.

WARNING

A procedure which, if not properly followed, may

cause injury to the operator or others in the oper-

ating area.

1.02 Important Safety Precautions

WARNINGS

OPERATION AND MAINTENANCE OF

PLASMA ARC EQUIPMENT CAN BE DAN-

GEROUS AND HAZARDOUS TO YOUR

HEALTH.

Plasma arc cutting produces intense electric and

magnetic emissions that may interfere with the

proper function of cardiac pacemakers, hearing

aids, or other electronic health equipment. Per-

sons who work near plasma arc cutting applica-

tions should consult their medical health profes-

sional and the manufacturer of the health

equipment to determine whether a hazard exists.

To prevent possible injury, read, understand and

follow all warnings, safety precautions and in-

structions before using the equipment. Call 1-603-

298-5711 or your local distributor if you have any

questions.

GASES AND FUMES

Gases and fumes produced during the plasma cutting

process can be dangerous and hazardous to your health.

• Keep all fumes and gases from the breathing

area. Keep your head out of the welding fume

plume.

• Use an air-supplied respirator if ventilation is

not adequate to remove all fumes and gases.

• The kinds of fumes and gases from the plasma

arc depend on the kind of metal being used, coat-

ings on the metal, and the different processes. You

must be very careful when cutting or welding any

metals which may contain one or more of the fol-

lowing:

Antimony Chromium Mer-

cury

Arsenic Cobalt Nickel

Barium Copper Selenium

Beryllium Lead Silver

Cadmium Manganese Vanadium

• Always read the Material Safety Data Sheets

(MSDS) that should be supplied with the material

you are using. These MSDSs will give you the in-

formation regarding the kind and amount of fumes

and gases that may be dangerous to your health.

• For information on how to test for fumes and

gases in your workplace, refer to item 1 in Subsec-

tion 1.03, Publications in this manual.

• Use special equipment, such as water or down

draft cutting tables, to capture fumes and gases.

• Do not use the plasma torch in an area where

combustible or explosive gases or materials are lo-

cated.

• Phosgene, a toxic gas, is generated from the va-

pors of chlorinated solvents and cleansers. Remove

all sources of these vapors.

• This product, when used for welding or cutting,

produces fumes or gases which contain chemicals

known to the State of California to cause birth de-

fects and, in some cases, cancer. (California Health

& Safety Code Sec. 25249.5 et seq.)

ELECTRIC SHOCK

Electric Shock can injure or kill. The plasma arc process

uses and produces high voltage electrical energy. This

electric energy can cause severe or fatal shock to the op-

erator or others in the workplace.

GENERAL INFORMATION 2 Date: November 15, 2001

• Never touch any parts that are electrically “live”

or “hot.”

• Wear dry gloves and clothing. Insulate yourself

from the work piece or other parts of the welding

circuit.

• Repair or replace all worn or damaged parts.

• Extra care must be taken when the workplace is

moist or damp.

• Install and maintain equipment according to

NEC code, refer to item 9 in Subsection 1.03, Pub-

lications.

• Disconnect power source before performing any

service or repairs.

• Read and follow all the instructions in the Op-

erating Manual.

FIRE AND EXPLOSION

Fire and explosion can be caused by hot slag, sparks, or

the plasma arc.

• Be sure there is no combustible or flammable ma-

terial in the workplace. Any material that cannot

be removed must be protected.

• Ventilate all flammable or explosive vapors from

the workplace.

• Do not cut or weld on containers that may have

held combustibles.

• Provide a fire watch when working in an area

where fire hazards may exist.

• Hydrogen gas may be formed and trapped un-

der aluminum workpieces when they are cut un-

derwater or while using a water table. DO NOT

cut aluminum alloys underwater or on a water

table unless the hydrogen gas can be eliminated or

dissipated. Trapped hydrogen gas that is ignited

will cause an explosion.

NOISE

Noise can cause permanent hearing loss. Plasma arc pro-

cesses can cause noise levels to exceed safe limits. You

must protect your ears from loud noise to prevent per-

manent loss of hearing.

• To protect your hearing from loud noise, wear

protective ear plugs and/or ear muffs. Protect oth-

ers in the workplace.

• Noise levels should be measured to be sure the

decibels (sound) do not exceed safe levels.

• For information on how to test for noise, see item

1 in Subsection 1.03, Publications, in this manual.

PLASMA ARC RAYS

Plasma Arc Rays can injure your eyes and burn your skin.

The plasma arc process produces very bright ultra violet

and infra red light. These arc rays will damage your

eyes and burn your skin if you are not properly protected.

• To protect your eyes, always wear a welding hel-

met or shield. Also always wear safety glasses with

side shields, goggles or other protective eye wear.

• Wear welding gloves and suitable clothing to

protect your skin from the arc rays and sparks.

• Keep helmet and safety glasses in good condi-

tion. Replace lenses when cracked, chipped or

dirty.

• Protect others in the work area from the arc rays.

Use protective booths, screens or shields.

• Use the shade of lens as suggested in the fol-

lowing per ANSI/ASC Z49.1:

Minimum Protective Suggested

Arc Current Shade No. Shade No.

Less Than 300* 8 9

300 - 400* 9 12

400 - 800* 10 14

* These values apply where the actual arc is clearly

seen. Experience has shown that lighter filters

may be used when the arc is hidden by the work-

piece.

1.03 Publications

Refer to the following standards or their latest revisions

for more information:

1. OSHA, SAFETY AND HEALTH STANDARDS, 29CFR

1910, obtainable from the Superintendent of Docu-

ments, U.S. Government Printing Office, Washington,

D.C. 20402

2. ANSI Standard Z49.1, SAFETY IN WELDING AND

CUTTING, obtainable from the American Welding So-

ciety, 550 N.W. LeJeune Rd, Miami, FL 33126

3. NIOSH, SAFETY AND HEALTH IN ARC WELDING

AND GAS WELDING AND CUTTING, obtainable

from the Superintendent of Documents, U.S. Govern-

ment Printing Office, Washington, D.C. 20402

4. ANSI Standard Z87.1, SAFE PRACTICES FOR OCCU-

PATION AND EDUCATIONAL EYE AND FACE PRO-

TECTION, obtainable from American National Stan-

dards Institute, 1430 Broadway, New York, NY 10018

Date: November 15, 2001 3 GENERAL INFORMATION

5. ANSI Standard Z41.1, STANDARD FOR MEN’S

SAFETY-TOE FOOTWEAR, obtainable from the Ameri-

can National Standards Institute, 1430 Broadway, New

York, NY 10018

6. ANSI Standard Z49.2, FIRE PREVENTION IN THE USE

OF CUTTING AND WELDING PROCESSES, obtain-

able from American National Standards Institute, 1430

Broadway, New York, NY 10018

7. AWS Standard A6.0, WELDING AND CUTTING CON-

TAINERS WHICH HAVE HELD COMBUSTIBLES, ob-

tainable from American Welding Society, 550 N.W.

LeJeune Rd, Miami, FL 33126

8. NFPA Standard 51, OXYGEN-FUEL GAS SYSTEMS

FOR WELDING, CUTTING AND ALLIED PRO-

CESSES, obtainable from the National Fire Protection

Association, Batterymarch Park, Quincy, MA 02269

9. NFPA Standard 70, NATIONAL ELECTRICAL CODE,

obtainable from the National Fire Protection Associa-

tion, Batterymarch Park, Quincy, MA 02269

10. NFPA Standard 51B, CUTTING AND WELDING PRO-

CESSES, obtainable from the National Fire Protection

Association, Batterymarch Park, Quincy, MA 02269

11. CGA Pamphlet P-1, SAFE HANDLING OF COM-

PRESSED GASES IN CYLINDERS, obtainable from the

Compressed Gas Association, 1235 Jefferson Davis

Highway, Suite 501, Arlington, VA 22202

12. CSA Standard W117.2, CODE FOR SAFETY IN WELD-

ING AND CUTTING, obtainable from the Canadian

Standards Association, Standards Sales, 178 Rexdale

Boulevard, Rexdale, Ontario, Canada M9W 1R3

13. NWSA booklet, WELDING SAFETY BIBLIOGRAPHY

obtainable from the National Welding Supply Associa-

tion, 1900 Arch Street, Philadelphia, PA 19103

14. American Welding Society Standard AWSF4.1, RECOM-

MENDED SAFE PRACTICES FOR THE PREPARA-

TION FOR WELDING AND CUTTING OF CONTAIN-

ERS AND PIPING THAT HAVE HELD HAZARDOUS

SUBSTANCES, obtainable from the American Welding

Society, 550 N.W. LeJeune Rd, Miami, FL 33126

15. ANSI Standard Z88.2, PRACTICE FOR RESPIRATORY

PROTECTION, obtainable from American National

Standards Institute, 1430 Broadway, New York, NY

10018

1.04 Note, Attention et

Avertissement

Dans ce manuel, les mots “note,” “attention,” et

“avertissement” sont utilisés pour mettre en relief des

informations à caractère important. Ces mises en relief

sont classifiées comme suit :

NOTE

Toute opération, procédure ou renseignement

général sur lequel il importe d’insister davantage

ou qui contribue à l’efficacité de fonctionnement

du système.

ATTENTION

Toute procédure pouvant résulter

l’endommagement du matériel en cas de non-

respect de la procédure en question.

AVERTISSEMENT

Toute procédure pouvant provoquer des blessures

de l’opérateur ou des autres personnes se trouvant

dans la zone de travail en cas de non-respect de la

procédure en question.

1.05 Precautions De Securite

Importantes

AVERTISSEMENTS

L’OPÉRATION ET LA MAINTENANCE DU

MATÉRIEL DE SOUDAGE À L’ARC AU JET

DE PLASMA PEUVENT PRÉSENTER DES

RISQUES ET DES DANGERS DE SANTÉ.

Coupant à l’arc au jet de plasma produit de l’énergie

électrique haute tension et des émissions

magnétique qui peuvent interférer la fonction

propre d’un “pacemaker” cardiaque, les appareils

auditif, ou autre matériel de santé electronique.

Ceux qui travail près d’une application à l’arc au

jet de plasma devrait consulter leur membre

professionel de médication et le manufacturier de

matériel de santé pour déterminer s’il existe des

risques de santé.

Il faut communiquer aux opérateurs et au person-

nel TOUS les dangers possibles. Afin d’éviter les

blessures possibles, lisez, comprenez et suivez tous

les avertissements, toutes les précautions de sécurité

et toutes les consignes avant d’utiliser le matériel.

Composez le + 603-298-5711 ou votre distributeur

local si vous avez des questions.

FUMÉE et GAZ

GENERAL INFORMATION 4 Date: November 15, 2001

La fumée et les gaz produits par le procédé de jet de

plasma peuvent présenter des risques et des dangers de

santé.

• Eloignez toute fumée et gaz de votre zone de respira-

tion. Gardez votre tête hors de la plume de fumée

provenant du chalumeau.

• Utilisez un appareil respiratoire à alimentation en air

si l’aération fournie ne permet pas d’éliminer la fumée

et les gaz.

• Les sortes de gaz et de fumée provenant de l’arc de

plasma dépendent du genre de métal utilisé, des

revêtements se trouvant sur le métal et des différents

procédés. Vous devez prendre soin lorsque vous

coupez ou soudez tout métal pouvant contenir un ou

plusieurs des éléments suivants:

antimoine cadmium

mercure

argent chrome nickel

arsenic cobalt plomb

baryum cuivre sélénium

béryllium manganèse vana-

dium

• Lisez toujours les fiches de données sur la sécurité

des matières (sigle américain “MSDS”); celles-ci

devraient être fournies avec le matériel que vous

utilisez. Les MSDS contiennent des renseignements

quant à la quantité et la nature de la fumée et des gaz

pouvant poser des dangers de santé.

• Pour des informations sur la manière de tester la

fumée et les gaz de votre lieu de travail, consultez

l’article 1 et les documents cités à la page 5.

• Utilisez un équipement spécial tel que des tables de

coupe à débit d’eau ou à courant descendant pour

capter la fumée et les gaz.

• N’utilisez pas le chalumeau au jet de plasma dans une

zone où se trouvent des matières ou des gaz combus-

tibles ou explosifs.

• Le phosgène, un gaz toxique, est généré par la fumée

provenant des solvants et des produits de nettoyage

chlorés. Eliminez toute source de telle fumée.

• Ce produit, dans le procéder de soudage et de coupe,

produit de la fumée ou des gaz pouvant contenir des

éléments reconnu dans L’état de la Californie, qui

peuvent causer des défauts de naissance et le cancer.

(La sécurité de santé en Californie et la code sécurité

Sec. 25249.5 et seq.)

CHOC ELECTRIQUE

Les chocs électriques peuvent blesser ou même tuer. Le

procédé au jet de plasma requiert et produit de l’énergie

électrique haute tension. Cette énergie électrique peut

produire des chocs graves, voire mortels, pour l’opérateur

et les autres personnes sur le lieu de travail.

• Ne touchez jamais une pièce “sous tension” ou “vive”;

portez des gants et des vêtements secs. Isolez-vous

de la pièce de travail ou des autres parties du circuit

de soudage.

• Réparez ou remplacez toute pièce usée ou

endommagée.

• Prenez des soins particuliers lorsque la zone de tra-

vail est humide ou moite.

• Montez et maintenez le matériel conformément au

Code électrique national des Etats-Unis. (Voir la page

5, article 9.)

• Débranchez l’alimentation électrique avant tout tra-

vail d’entretien ou de réparation.

• Lisez et respectez toutes les consignes du Manuel de

consignes.

INCENDIE ET EXPLOSION

Les incendies et les explosions peuvent résulter des scories

chaudes, des étincelles ou de l’arc de plasma. Le procédé

à l’arc de plasma produit du métal, des étincelles, des

scories chaudes pouvant mettre le feu aux matières com-

bustibles ou provoquer l’explosion de fumées

inflammables.

• Soyez certain qu’aucune matière combustible ou in-

flammable ne se trouve sur le lieu de travail. Protégez

toute telle matière qu’il est impossible de retirer de la

zone de travail.

• Procurez une bonne aération de toutes les fumées

inflammables ou explosives.

• Ne coupez pas et ne soudez pas les conteneurs ayant

pu renfermer des matières combustibles.

• Prévoyez une veille d’incendie lors de tout travail dans

une zone présentant des dangers d’incendie.

• Le gas hydrogène peut se former ou s’accumuler sous

les pièces de travail en aluminium lorsqu’elles sont

coupées sous l’eau ou sur une table d’eau. NE PAS

couper les alliages en aluminium sous l’eau ou sur

une table d’eau à moins que le gas hydrogène peut

s’échapper ou se dissiper. Le gas hydrogène accumulé

explosera si enflammé.

Date: November 15, 2001 5 GENERAL INFORMATION

RAYONS D’ARC DE PLASMA

Les rayons provenant de l’arc de plasma peuvent blesser

vos yeux et brûler votre peau. Le procédé à l’arc de

plasma produit une lumière infra-rouge et des rayons

ultra-violets très forts. Ces rayons d’arc nuiront à vos

yeux et brûleront votre peau si vous ne vous protégez

pas correctement.

• Pour protéger vos yeux, portez toujours un casque ou

un écran de soudeur. Portez toujours des lunettes de

sécurité munies de parois latérales ou des lunettes de

protection ou une autre sorte de protection oculaire.

• Portez des gants de soudeur et un vêtement protecteur

approprié pour protéger votre peau contre les

étincelles et les rayons de l’arc.

• Maintenez votre casque et vos lunettes de protection

en bon état. Remplacez toute lentille sale ou

comportant fissure ou rognure.

• Protégez les autres personnes se trouvant sur la zone

de travail contre les rayons de l’arc en fournissant des

cabines ou des écrans de protection.

• Utilisez la nuance de lentille qui est suggèrée dans le

recommendation qui suivent ANSI/ASC Z49.1:

Nuance Minimum Nuance Suggerée

Courant Arc Protective Numéro Numéro

Moins de 300* 8 9

300 - 400* 9 12

400 - 800* 10 14

* Ces valeurs s’appliquent ou l’arc actuel est observé

clairement. L’experience a démontrer que les filtres

moins foncés peuvent être utilisés quand l’arc est

caché par moiceau de travail.

BRUIT

Le bruit peut provoquer une perte permanente de l’ouïe.

Les procédés de soudage à l’arc de plasma peuvent

provoquer des niveaux sonores supérieurs aux limites

normalement acceptables. Vous dú4ez vous protéger les

oreilles contre les bruits forts afin d’éviter une perte

permanente de l’ouïe.

• Pour protéger votre ouïe contre les bruits forts, portez

des tampons protecteurs et/ou des protections

auriculaires. Protégez également les autres personnes

se trouvant sur le lieu de travail.

• Il faut mesurer les niveaux sonores afin d’assurer que

les décibels (le bruit) ne dépassent pas les niveaux

sûrs.

• Pour des renseignements sur la manière de tester le

bruit, consultez l’article 1, page 5.

1.06 Documents De Reference

Consultez les normes suivantes ou les révisions les plus

récentes ayant été faites à celles-ci pour de plus amples

renseignements :

1. OSHA, NORMES DE SÉCURITÉ DU TRAVAIL ET DE

PROTECTION DE LA SANTÉ, 29CFR 1910,

disponible auprès du Superintendent of Documents,

U.S. Government Printing Office, Washington, D.C.

20402

2. Norme ANSI Z49.1, LA SÉCURITÉ DES

OPÉRATIONS DE COUPE ET DE SOUDAGE,

disponible auprès de la Société Américaine de

Soudage (American Welding Society), 550 N.W.

LeJeune Rd., Miami, FL 33126

3. NIOSH, LA SÉCURITÉ ET LA SANTÉ LORS DES

OPÉRATIONS DE COUPE ET DE SOUDAGE À

L’ARC ET AU GAZ, disponible auprès du Superin-

tendent of Documents, U.S. Government Printing

Office, Washington, D.C. 20402

4. Norme ANSI Z87.1, PRATIQUES SURES POUR LA

PROTECTION DES YEUX ET DU VISAGE AU TRA-

VAIL ET DANS LES ECOLES, disponible de l’Institut

Américain des Normes Nationales (American Na-

tional Standards Institute), 1430 Broadway, New York,

NY 10018

5. Norme ANSI Z41.1, NORMES POUR LES

CHAUSSURES PROTECTRICES, disponible auprès

de l’American National Standards Institute, 1430

Broadway, New York, NY 10018

6. Norme ANSI Z49.2, PRÉVENTION DES INCENDIES

LORS DE L’EMPLOI DE PROCÉDÉS DE COUPE ET

DE SOUDAGE, disponible auprès de l’American Na-

tional Standards Institute, 1430 Broadway, New York,

NY 10018

7. Norme A6.0 de l’Association Américaine du Soudage

(AWS), LE SOUDAGE ET LA COUPE DE

CONTENEURS AYANT RENFERMÉ DES PRODUITS

COMBUSTIBLES, disponible auprès de la American

Welding Society, 550 N.W. LeJeune Rd., Miami, FL

33126

8. Norme 51 de l’Association Américaine pour la Pro-

tection contre les Incendies (NFPA), LES SYSTEMES

À GAZ AVEC ALIMENTATION EN OXYGENE

POUR LE SOUDAGE, LA COUPE ET LES

PROCÉDÉS ASSOCIÉS, disponible auprès de la Na-

tional Fire Protection Association, Batterymarch Park,

Quincy, MA 02269

GENERAL INFORMATION 6 Date: November 15, 2001

9. Norme 70 de la NFPA, CODE ELECTRIQUE NA-

TIONAL, disponible auprès de la National Fire Pro-

tection Association, Batterymarch Park, Quincy, MA

02269

10. Norme 51B de la NFPA, LES PROCÉDÉS DE

COUPE ET DE SOUDAGE, disponible auprès de la

National Fire Protection Association, Batterymarch

Park, Quincy, MA 02269

11. Brochure GCA P-1, LA MANIPULATION SANS

RISQUE DES GAZ COMPRIMÉS EN CYLINDRES,

disponible auprès de l’Association des Gaz

Comprimés (Compressed Gas Association), 1235

Jefferson Davis Highway, Suite 501, Arlington, VA

22202

12. Norme CSA W117.2, CODE DE SÉCURITÉ POUR

LE SOUDAGE ET LA COUPE, disponible auprès

de l’Association des Normes Canadiennes, Stan-

dards Sales, 178 Rexdale Boulevard, Rexdale,

Ontario, Canada, M9W 1R3

13.Livret NWSA, BIBLIOGRAPHIE SUR LA

SÉCURITÉ DU SOUDAGE, disponible auprès de

l’Association Nationale de Fournitures de Soudage

(National Welding Supply Association), 1900 Arch

Street, Philadelphia, PA 19103

14. Norme AWSF4.1 de l’Association Américaine de

Soudage, RECOMMANDATIONS DE PRATIQUES

SURES POUR LA PRÉPARATION À LA COUPE ET

AU SOUDAGE DE CONTENEURS ET TUYAUX

AYANT RENFERMÉ DES PRODUITS

DANGEREUX , disponible auprès de la American

Welding Society, 550 N.W. LeJeune Rd., Miami, FL

33126

15. Norme ANSI Z88.2, PRATIQUES DE PROTECTION

RESPIRATOIRE, disponible auprès de l’American

National Standards Institute, 1430 Broadway, New

York, NY 10018

Date: November 15, 2001 7 GENERAL INFORMATION

1.07 Declaration of Conformity

Manufacturer: Thermal Dynamics Corporation

Address: 82 Benning Street

West Lebanon, New Hampshire 03784

USA

The equipment described in this manual conforms to all applicable aspects and regulations of the ‘Low Voltage Directive’

(European Council Directive 73/23/EEC as amended by Council Directive 93/68/EEC) and to the National legislation for

the enforcement of this Directive.

Serial numbers are unique with each individual piece of equipment and details description, parts used to manufacture a unit

and date of manufacture.

National Standard and Technical Specifications

The product is designed and manufactured to a number of standards and technical requirements. Among them are:

* CSA (Canadian Standards Association) standard C22.2 number 60 for Arc welding equipment.

* UL (Underwriters Laboratory) rating 94VO flammability testing for all printed-circuit boards used.

* ISO/IEC 60974-1 (BS 638-PT10) (EN 60 974-1) (EN50192) (EN50078) applicable to plasma cutting equipment and associ-

ated accessories.

* Extensive product design verification is conducted at the manufacturing facility as part of the routine design and manufac-

turing process. This is to ensure the product is safe, when used according to instructions in this manual and related

industry standards, and performs as specified. Rigorous testing is incorporated into the manufacturing process to ensure

the manufactured product meets or exceeds all design specifications.

Thermal Dynamics has been manufacturing products for more than 30 years, and will continue to achieve excellence in our

area of manufacture.

Manufacturers responsible representative: Giorgio Bassi

Managing Director

Thermal Dynamics Europe

Via rio Fabbiani 8A

40067 Rastignano (BO)

Italy

GENERAL INFORMATION 8 Date: November 15, 2001

1.08 Statement of Warranty

LIMITED WARRANTY: Thermal Dynamics

Corporation (hereinafter “Thermal”) warrants that its products will be free of defects in

workmanship or material. Should any failure to conform to this warranty appear within the time period applicable to the Thermal

products as stated below, Thermal shall, upon notification thereof and substantiation that the product has been stored, installed, operated,

and maintained in accordance with Thermal’s specifications, instructions, recommendations and recognized standard industry practice,

and not subject to misuse, repair, neglect, alteration, or accident, correct such defects by suitable repair or replacement, at Thermal’s sole

option, of any components or parts of the product determined by Thermal to be defective.

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE.

LIMITATION OF LIABILITY: Thermal shall not under any circumstances be liable for special or consequential damages, such as, but

not limited to, damage or loss of purchased or replacement goods, or claims of customers of distributor (hereinafter “Purchaser”) for

service interruption. The remedies of the Purchaser set forth herein are exclusive and the liability of Thermal with respect to any

contract, or anything done in connection therewith such as the performance or breach thereof, or from the manufacture, sale, delivery,

resale, or use of any goods covered by or furnished by Thermal whether arising out of contract, negligence, strict tort, or under any

warranty, or otherwise, shall not, except as expressly provided herein, exceed the price of the goods upon which such liability is based.

THIS WARRANTY BECOMES INVALID IF REPLACEMENT PARTS OR ACCESSORIES ARE USED WHICH MAY IMPAIR THE

SAFETY OR PERFORMANCE OF ANY THERMAL PRODUCT.

THIS WARRANTY IS INVALID IF THE PRODUCT IS SOLD BY NON-AUTHORIZED PERSONS.

The limited warranty periods for Thermal products shall be as follows (with the exception of XL Plus Series, CutMaster Series , Cougar

and DRAG-GUN): A maximum of three (3) years from date of sale to an authorized distributor and a maximum of two (2) years from

date of sale by such distributor to the Purchaser, and with the further limitations on such two (2) year period (see chart below).

The limited warranty period for XL Plus Series and CutMaster Series shall be as follows: A maximum of four (4) years from date

of sale to an authorized distributor and a maximum of three (3) years from date of sale by such distributor to the Purchaser, and

with the further limitations on such three (3) year period (see chart below).

The limited warranty period for Cougar and DRAG-GUN shall be as follows: A maximum of two (2) years from date of sale to an

authorized distributor and a maximum of one (1) year from date of sale by such distributor to the Purchaser, and with the further

limitations on such two (2) year period (see chart below).

Parts

XL Plus & Parts Parts

PAK Units, Power Supplies CutMaster Series Cougar/Drag-Gun All Others Labor

Main Power Magnetics 3 Years 1 Year 2 Years 1 Year

Original Main Power Rectifier 3 Years 1 Year 2 Years 1 Year

Control PC Board 3 Years 1 Year 2 Years 1 Year

All Other Circuits And Components Including, 1 Year 1 Year 1 Year 1 Year

But Not Limited To, Starting Circuit,

Contactors, Relays, Solenoids, Pumps,

Power Switching Semi-Conductors

Consoles, Control Equipment, Heat 1 Year 1 Year 1 Year

Exchanges, And Accessory Equipment

Torch And Leads

Maximizer 300 Torch 1 Year 1 Year

SureLok Torches 1 Year 1 Year 1 Year

All Other Torches 180 Days 180 Days 180 Days 180 Days

Repair/Replacement Parts 90 Days 90 Days 90 Days None

Warranty repairs or replacement claims under this limited warranty must be submitted by an authorized Thermal Dynamics® repair

facility within thirty (30) days of the repair. No transportation costs of any kind will be paid under this warranty. Transportation

charges to send products to an authorized warranty repair facility shall be the responsibility of the customer. All returned goods shall

be at the customer’s risk and expense. This warranty supersedes all previous Thermal warranties.

Effective: November 15, 2001

Manual 0-2472 9 SECTION 2: GENERAL INFORMATION

SECTION 2:

GENERAL INFORMATION

2.01 Scope of this Manual

This manual provides operating instructions and basic

maintenance procedures for the Thermal Arc ULTIMA-

150

Plasma Welding Power Supply. Service of this equip-

ment is restricted to Thermal Dynamics trained person-

nel; unqualified personnel are strictly cautioned against

attempting repairs or adjustments not covered in this

manual, at the risk of voiding the warranty.

Read this manual thoroughly. A complete understanding

of the capabilities and functions of the equipment will

assure the dependable operation for which it was designed.

2.02 ULTIMA-150 Power Supply

Description

The ULTIMA-150 Plasma Welding Power Supply is one

integrated unit providing power, pilot control inverter, and

coolant recirculator. With output ranges from 0.5-15 amps

and 5-150 amps, the power supply is ideally suited for all

low current gas tungsten arc welding (GTAW) and auto-

mated welding applications. Suitable for use with all des-

ignated Thermal Dynamics plasma welding torches.

2.03 ULTIMA-150 Power Supply

Specifications

A. Input Power

200 VAC ±10% 50/60hz, 1 or 3 phase

208 VAC ±10% 50/60hz, 1 or 3 phase

230 VAC ±10% 50/60hz, 1 or 3 phase

380 VAC ±10% 50/60hz, 1 or 3 phase

415 VAC ±10% 50/60hz, 1 or 3 phase

460 VAC ±10% 50/60hz, 1 or 3 phase

575 VAC ±10% 50/60hz 3 phase (available with

optional Transformer Module

only)

B. Output Power

1. Output Amps

Range I - 0.5 to 15 amps DC Straight Polarity

Range II - 5 to 150 amps DC Straight Polarity

2. Duty Cycle

60% Duty Cycle @ 40ºC, 150 amp output

100% Duty Cycle @ 40°C, 100 amp output

3. Pilot Arc Output

2-15 amp Variable, Continuous Pilot Arc

Pilot Arc Output 100% Duty Cycle @ 40º C

C. Fuse

3A, 500V (1FU) Fuse

D. Protection Features

A number of interlocks have been to provided to assure

proper handling of fault conditions at all times.

• Coolant flow and level - Monitored and shut down

the recirculator pump when below minimum levels.

• Pump operation - System shuts down due to air in

torch leads or in the system.

• Coolant and power supply - Over temperature of the

power supply or coolant will immediately disable

the power supply output. The recirculator pump re-

mains running for system and coolant cool down.

• Plasma gas and shield gas - Both have minimum

pressure switches that disable pilot arc operation.

• Pilot arc - Always latched off in event of power sup-

ply interlock trip. The pilot must be disabled and

then re-energized to initiate the pilot arc after a fault

shutdown.

E. Gas Supply

Plasma Gas - 0.5-3.0 scfh

Shield Gas - 5.0-30 scfh

F. Coolant Reservoir Capacity

only

G. Weight

130 lbs (59 kg) - ULTIMA-150 Power Supply only

150 lbs (68kg) - shipping weight (including coolant

and torch)

H. Dimensions

18" high (457 mm) x 15" wide (381 mm) x 28.5" deep

(724 mm)

SECTION 2: GENERAL INFORMATION 10 Manual 0-2472

2.04 The ULTIMA-150 System

The ULTIMA-150 Plasma Welding System includes the

following components:

• ULTIMA-150 Power Supply with 10 ft Gas Supply

Hoses (2)

• Quick Disconnect Torch with leads (torch type and

lead length as ordered)

• Torch Spare Parts Kit

• Thermal Arc Coolant - 2 gallons

• 10 ft Work Cable with Cable Lug connector.

Figure 2-1 The ULTIMA-150 System

2.05 Requirements to Complete

System

To complete the system, the user needs the following:

• Remote signal to operate Arc ON/OFF via TB-1 in-

terface or J-20 receptacle using accessory remote de-

vice

• Gas Pressure Regulators. Both Argon Gas Regula-

tor and Argon/Hydrogen Gas Regulators are avail-

able through Thermal Dynamics

• Power Input Cable

2.06 Options, Accessories, and

Replacement Parts

Options and accessories are available for the ULTIMA-

150 Plasma Welding Power Supply to customize it for a

particular application or to further enhance performance.

For more information, refer to Section 6, Parts Replace-

ment.

• Quick Disconnect Adapter Kit - For use with older

model Thermal Arc torches. The Adapter Kit retro-

fits the torch for direct connection to the quick dis-

connect receptacle on the Power Supply.

• Torch Spare Parts Kit - Kit contains replacement front

end torch parts.

• 575-Volt Transformer Module - A step-down trans-

former which converts 575V primary power to 460V

for use with the ULTIMA-150 Plasma Welding Power

Supply.

• Remote Current Control Device - Required for opera-

tion of the ULTIMA-150 Plasma Welding System.

• Weld Sequencer - An add-on accessory for control-

ling weld timing, pulsing, current slope, and gas

slope.

• Coolant Pressure Gauge Assembly Kit - This kit al-

lows for easy monitoring and adjusting of coolant

pressure.

Manual 0-2472 11 SECTION 2: GENERAL INFORMATION

2.07 Introduction to Plasma Arc

Welding

Plasma is a gas which has been heated to an extremely

high temperature and ionized so that the gas becomes elec-

trically conductive. The welding process uses this plasma

gas to transfer an electric arc to the work piece. The metal

to be welded is melted by the heat of this arc.

In a Thermal Arc Plasma Welding Torch, a cool gas such

as argon enters Zone A (Figure 2-2). In Zone B, a pilot arc

between the electrode and the front of the torch heats and

ionizes the gas. An arc transfers to the work piece through

the column of gas in Zone C.

Workpiece

Power

Supply

A-00812

Figure 2-2 Thermal Arc Plasma Welding

By forcing the plasma gas and electric arc through a small

orifice, Thermal Arc torches deliver a high concentration

of heat to a very small area. The stiff, constricted plasma

arc is shown in Zone C. Direct current straight polarity

(DCSP) is used for plasma welding, as shown in the illus-

tration.

The exclusive Dual-Flow design of Thermal Arc welding

torches uses a shield gas, shown by the small arrows. The

shield gas surrounds the plasma arc and channels it to

the workpiece, shielding the welding puddle.

Coolant from the coolant recirculator flows through the

liquid cooled power leads to the torch head and back.

The plasma arc is infinitely variable from soft to stiff. Most

applications can best be accomplished with a softer arc

(lower plasma gas flow). Full penetration or ‘keyhole’

welding requires a stiff arc (high plasma gas flow).

Individual welding torch instruction manuals contain

detailed information on these parameters.

2.08 Theory of Operation

A. Plasma and Shield Gases

Plasma and shield gases flow through the ULTIMA-

150 at rates set at the console flow meter controls. The

flow rate of each gas is indicated on the front panel

flow meters. Solenoid valves inside the unit turn the

gases on and off. The gas pressure interlock shuts the

system down if plasma gas pressure falls below 25

psi.

The plasma gas flows through the positive (black)

torch lead, around the electrode and gas distributor,

and out through the tip orifice. The shield gas flows

through the negative (yellow) torch lead, around the

torch front end and out through the shield cup.

Two pressure switches act as an interlock for the gas

supply. If supply pressure falls below minimum re-

quirements the pressure switches will open, shutting

off the power to the contactor, and the GAS indicator,

will go out. When adequate gas supply pressure is

available the pressure switches close, allowing power

to be resumed for welding.

B. Pilot Arc

When the torch is started a pilot arc is established

between the electrode and cutting tip. This pilot arc

creates a path for the main arc to transfer to the work.

Direct current (DC) alone is not enough to start the

main welding arc. High frequency is used momen-

tarily. The high frequency jumps between the tip and

electrode with the DC following, then the high fre-

quency turns off. The Pilot Indicator will be lighted

when the pilot arc is enabled.

C. Current Control

The welding current is controlled by remote or at the

power supply. The weld arc ON/OFF is controlled

remotely by the user - by remote pendant, foot control,

or remote signal.

D. Coolant Flow

Coolant flows from the coolant recirculator, through

the negative torch lead to the torch head and returns

through the positive torch lead. The coolant pressure

interlock shuts the system down if the coolant pres-

sure falls below 35 psi.

E. Welding Current

The power supply provides the welding current. The

negative (green) output is connected to the torch elec-

trode through the liquid cooled lead. The positive

output is connected to the workpiece through the work

cable.

SECTION 2: GENERAL INFORMATION 12 Manual 0-2472

Manual 0-2472 13 SECTION 3: INSTALLATION

SECTION 3:

INSTALLATION

3.01 Introduction

This section describes installation procedures for the

ULTIMA-150 Power Supply. These instructions apply

to the power supply only; installation procedures for

options and accessories can be found in manuals pro-

vided for those components.

3.02 Site Location

Select a clean, dry location with good ventilation and ad-

equate working space around all components. The power

supply is cooled by air flow through the front and rear.

Air flow must not be obstructed. At least 2 feet (0.61 m) of

clearance should be provided at the front and rear with at

least 6 inches (0.15 m) of clearance on each side.

CAUTION

Operation without proper air flow will inhibit

proper cooling and reduce duty cycle.

NOTE

Review the safety precautions in the front of this

manual to be sure that the location meets all safety

requirements.

3.03 Unpacking

The ULTIMA-150 is carefully packed to protect it from

damage during shipping. Components may be packed in

one carton or separately in several cartons, depending on

the system configuration and accessories ordered.

1. Unpack each item and remove all packing mate-

rial.

2. Locate the packing list(s) and use the list to iden-

tify and account for each item.

3. Inspect each item for possible shipping damage. If

damage is evident, contact your distributor before

proceeding with installation.

3.04 Primary Input Power

Connections

The ULTIMA-150 Plasma Welding Power Supply accepts

input voltages from 200V to 460V. Input can be 50 or 60

Hz, single-phase or three-phase.

The primary power source, power cable, and plug (sup-

plied by user) must conform to the local electric code and

the recommended circuit protection and wiring require-

ments. (See Appendix I for requirements.)

NOTE

Every system is factory-wired for 460V three-phase

input. For any other input voltage, the power sup-

ply must be reset by the user. Refer to Section 3.05,

Voltage Changeover, for instructions on how to

change the voltage setting.

For 575 Volt operation, an optional Transformer Module is

available. It is factory set to step down to 460V three-

phase input.

NOTE

Input power connections can be made directly to a

properly fused disconnect or by using a plug which

conforms to the recommended ratings.

WARNING

Disconnect primary power at the source before as-

sembling the power supply, torch parts or torch and

leads assemblies.

AC Input Cable

Ground

Fuse

Voltage

Selection

Plug

Primary

Power Switch

A-00813

Figure 3-1 Internal View Power Input Connections

SECTION 3: INSTALLATION 14 Manual 0-2472

AC Input

Power Connection

A-00814

Figure 3-2 Rear Panel Input Power Connection

A. Connections for Single-Phase

Single-phase operation requires a 2-conductor cable with

ground.

1. Remove the Enclosure Cover from the unit to set

up the correct electrical service.

2. Feed AC input cable through the strain relief on

rear panel of unit and tighten the strain relief

screws.

3. Insert the ground wire into the terminal marked

GND (ground) and tighten the set screw.

4. Connect the other two wires to terminals L1 and

L2 located on the top end of the Main Circuit Breaker

(MCB). L1 is the left terminal and L2 is the center

terminal when viewing the MCB from the rear.

Ground

Fuse

Primary

Power Switch

A-00815

Figure 3-3 Single-Phase Input Connections

WARNING

Make sure the ground wire is designated GND

on the other end of the cable. Electric shock

and damage to the unit could occur if power is

applied to the GND terminal.

La page charge ...

ESAB Plasma Welding Power Supply Manuel utilisateur

Marque: ESAB

Modèle: Plasma Welding Power Supply

Catégorie: Système de soudage

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: ESAB Plasma Welding Power Supply User manual

ESAB Plasma Welding Power Supply Manuel utilisateur

ESAB Plasma Welding Power Supply Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents