ENFORCER SD-962AR-36G Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
SD-962AR-36G
Grade 1 Rim-Type Exit Device
Manual
Heavy-duty ANSI Grade 1 steel
construction
Allows exit from inside while locked from
outside
Reversible non-handed design
For metal or wood doors up to
1
3
/
4
" (44mm) thick
Separate deadlocking latch prevents the
use of credit cards or similar means to open
the latch bolt
Fits doors from 33" to 48" (84~122 cm) wide
Hex-type
1
/
4
-turn dogging lock allows the exit
device to be unlocked for extended period of
time
Includes all needed hardware for typical
installation
Works with standard external door handle/lock
devices (not included)
Panic Hardware
51X4
ENFORCER Grade 1 Rim-Type Exit Device
2 SECO-LARM U.S.A., Inc.
Introduction:
The ENFORCER SD-962AR-36G Rim-Type Exit Device, when mounted on the inside of a door to
block entry to a protected premises, securely locks the door from outside access while allowing
users inside the protected premises to exit.
The stainless steel enclosure protects the exit device from abuse, yet easily unlocks the door from
the inside by users who require exit. It can be connected to an entry-type lever trim or to any
physical locking device on the outside of the door in order to allow entry to authorized personnel.
Dimensions:
Specifications:
Construction
ANSI Grade 1
steel
For doors 1
3
/
4
" (44mm) thick, wood or metal
Hand
Non
-
handed
Latch bolt Stainless steel,
3
/
4
" (19mm) throw
Dead latch Stainless steel
5
/
8
" (16mm) throw
Strike
For
5
/
8
"
(16mm) stop
Spring Stainless steel
Chassis Plated steel
Cover
Plated
zinc cast
Rail assembly Aluminum
End cap Plated zinc cast
Dogging
Hex
-
type dogging standard
Dimensions 33"x8"x2
3
/
16
" (838x203x56 mm)
Weight 9-lb 12-oz (4.4kg)
Parts List:
Screws Included:
1x Grade 1 Rim-Type Exit Device
1x Manual
1x Mounting template
1x Strike
1x Hex key
1x End cap
1x End cap bracket
Mounting hardware (see below)
Mounting chassis to door:
4x
1
/
4
"x
3
/
4
" machine screws
4x
1
/
4
"x
3
/
4
" wood screws
4x sex bolts
Connecting end cap to end cap bracket:
2x M4x6mm machine screws
Mounting end cap bracket to door:
2x
1
/
4
"x
3
/
4
" machine screws
2x
1
/
4
"x
3
/
4
" wood screws
Mounting strike to door:
2x
1
/
4
"x
3
/
4
" machine screws
2x
1
/
4
"x
3
/
4
" wood screws
1x #12x
3
/
4
" machine screw
8
"
(203mm)
2
13
/
16
"
(71mm)
2
3
/
16
"
(56mm)
2
3
/
8
"
(61mm)
33
"
(838mm)
2
1
/
4
"
(57mm)
ENFORCER Grade 1 Rim-Type Exit Device
SECO-LARM U.S.A., Inc. 3
Overview:
Sample Applications:
Double Door with Mullion
Single Door
Double Door
without Mullion
Chassis cover
Chassis
Mechanism housing
Push bar
Dogging device –
use hex
key to lock in
the open position so
the door can be
opened from outside
the protected
premises
End cap
Strike
End cap bracket
Mounting:
Strike
Door
Exit device
Trim
2
7
/
16
"
(62mm)
Door
Exit device
Trim Trim
Door
Exit device
2
7
/
16
"
(62mm)
Trim Trim
Door
Door
Exit device
Exit device
2
15
/
16
"
(75mm)
Double-door strike (not included)
Door
Draw line here
40"
(102cm)
ENFORCER Grade 1 Rim-Type Exit Device
4 SECO-LARM U.S.A., Inc.
Final Installation:
1.
Mark the vertical center line of the exit bar by drawing a line across th
e door at 40
"
above
the
floor. See "Mounting" on page 3.
2. Fold the included template, and align the center lines on the template with the center line drawn
on the door. Then mark the position of the mounting holes for the latch assembly.
See "Mounting" on page 3.
3. Move the template against the door stop and then mark the mounting holes for the strike.
4. Drill the holes as marked on the door and the mullion. See "Mounting" on page 3.
NOTE: Diagram shows 6 screws for mounting the chassis. Product only includes 4 screws. For best results, use 6 screws.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-
LARM
reserves the right to change specifications without notice. SECO-
LARM is also not responsible for misprints. All trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2020 SECO-
LARM U.S.A., Inc. All
rights reserved.
LIMITED WARRANTY: This SECO-
LARM product is warranted against defects in material and workmanship while
used in normal service for one (1) year from the date of sale to the original customer. SECO-
LARM’s obligation is limited to
the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty
is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-
LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole
obligation of SECO
-
LARM and the purchaser’s exclusive remedy, shall be limited t
o the replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-
LARM be liable for any special, collateral, incidental, or consequential
personal or property damage of any kind to the purchaser or anyone else.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
PITSW6
Phone: (949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com
MI_SD-962AR-36G_200512.docx
WARNING:
Incorrect mounting that leads to exposure or moisture inside the enclosure could damage the device and will
void the warranty.
WARNING: Un montage
incorrect qui conduit à une exposition à la pluie ou à l’humidité a l’intérieur de l’enceinte pourrait
endommager l’appareil et annuler la garantie.
-
1
-
2
-
3
-
4
ENFORCER SD-962AR-36G Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: ENFORCER SD-962AR-36G Owner's manual
