SPRAY MASTER™
WITH VELOCITY2 CONSUMABLES
MIG GUNS
Safety and
Operating
Instructions
AIR-COOLED MIG GUN
250 AMP
350 AMP
450 AMP
Revision: AF Issue Date: 02-03-2020 Manual No.: 89200016
English
French
Spanish
Italian
450
80%
UP TO
(2.4 MM)
UP TO
WIRE SIZE DUTY CYCLECURRENT
AMPS
UP TO
3/32”
QR CODE
WE APPRECIATE YOUR BUSINESS!
Congratulations on receiving your new Tweco Spray Master™ product.
We are proud to have you as our customer and will strive to provide
you with the best service and support in the industry. This product is
backed by our extensive warranty and world-wide service network.
We know you take pride in your work and we feel privileged to provide
you with this high performance product that will help you get the job
done.
For more than 75 years Tweco has provided quality products you can
trust, when your reputation is on the line.
YOU ARE IN GOOD COMPANY!
Tweco is a Global Brand of Arc Welding Products for ESAB. We
distinguish ourselves from our competition through market-leading
innovation and truly dependable products that will stand the test of
time.
We strive to enhance your productivity, efficiency and welding
performance, enabling you to excel in your craft. We design products
with the welder in mind delivering- advanced features, durability, ease
of use and ergonomic comfort.
Above all, we are committed to a safer working environment within
the welding industry. Your satisfaction with this product and its safe
operation is our ultimate concern. Please take the time to read the
entire manual, especially the Safety Precautions.
If you have any questions or concerns regarding your new Tweco
product, please contact our friendly and knowledgeable Customer
Service Team at:
1-800-462-2782 (USA) and 1-905-827-4515 (Canada),
or visit us on the web at www.esab.com/tweco.com
i
Spray Master
™
with VELOCITY2 MIG Guns
Safety and Operating Instructions
Instruction Guide Number: 89200016
Published by:
ESAB Group Inc.
2800 Airport Rd.
Denton, TX. 76207
(940) 566-2000
www.esab.com/tweco
U.S. Customer Care: (800) 426-1888
International Customer Care: (940) 381-1212
Canada Customer Care: 905-827-4515 / fax 800-588-1714
Copyright © 2014, 2015, 2018, 2019 ESAB. All rights reserved.
Reproduction of this work, in whole or in part, without written permission of the publisher is prohibited.
The publisher does not assume and hereby disclaims any liability to any party for any loss or damage
caused by any error or omission in this Manual, whether such error results from negligence, accident,
or any other cause.
For Printing Material Specication refer to document 47x1947
Publication Date: May 15, 2014
Revision Date: 02-03-2020
Record the following information for Warranty purposes:
Where Purchased:
Purchase Date:
Equipment Serial #:
!!
WARNING
Read and understand this entire Manual and your employer’s safety practices before installing, operating, or
servicing the equipment.
While the information contained in this Manual represents the Manufacturer's best judgment, the Manufac-
turer assumes no liability for its use.
ii
DECLARATION OF CONFORMITY
According to
The Low Voltage Directive 2014/35/EU, entering into force 20 April 2016
The RoHS Directive 2011/65/EC, entering into force 2 January 2013
Type of equipment
Hand Held Air/Gas and Water Cooled MIG Welding Torches
Type designation etc.
Spray Master MIG gun, Air Cooled
Brand name or trade mark
Tweco, an ESAB Brand
Manufacturer or his authorised representative
Name, address, telephone No:
ESAB Group Inc.
2800 Airport Rd
Denton TX 76207 USA
Phone: +01 800 426 1888, FAX +01 603 298 7402
The following harmonised standard in force within the EEA has been used in the design:
IEC/EN 60974-7:2019 Arc welding equipment - Part 7: Torches
Additional Information: Restrictive use, Class A equipment, intended for use in location other than residential.
By signing this document, the undersigned declares as manufacturer, or the manufacturer’s authorised
representative, that the equipment in question complies with the safety requirements stated above.
Date Signature Position
1 March 2019
Flavio Santos General Manager
Accessories and Adjacencies
2019
3
SECTION 1: SAFETY PRECAUTIONS
Table of Contents
SECTION 1: SAFETY PRECAUTIONS ..........................................................................3
Mesures de sécurité ......................................................................... 3
SECTION 2: INTRODUCTION ......................................................................................5
2.01 How to Use this Manual ................................................................... 5
2.02 Receipt of Equipment ....................................................................... 5
2.03 Description ....................................................................................... 5
SECTION 3: MIG GUN SPECIFICATIONS.....................................................................5
3.01 MIG Gun Classification ..................................................................... 5
3.02 Duty Cycle ........................................................................................ 5
3.03 MIG Gun Part Number Identification ................................................ 5
SECTION 4: MIG GUN INSTALLATION ........................................................................5
4.01 Direct Plug MIG Gun Installation ...................................................... 5
SECTION 5: SPRAY MASTER WITH VELOCITY2 MAINTENANCE ...............................6
5.01 Installing or Replacing VELOCITY2 Contact Tip ............................... 6
5.02 Conduit Identification ....................................................................... 6
Conduit Removal .............................................................................. 6
Conduit Installation .......................................................................... 6
5.03 Installing/Replacing Stainless Steel Sleeve / LOCK COLLAR ............ 6
5.04 Replace Conductor Tube .................................................................. 7
SECTION 6: CABLEHOZ® REPAIR .............................................................................7
6.01 Cablehoz® Repair ............................................................................ 7
SECTION 7: TROUBLESHOOTING ...............................................................................8
SECTION 8: CONSUMABLES ......................................................................................9
8.01 Tips and Nozzles .............................................................................. 9
8.02 Conduit .......................................................................................... 10
8.03 Conductor tube .............................................................................. 10
SECTION 9: REPLACEMENT PARTS .........................................................................11
SECTION 10: STATEMENT OF WARRANTY ..............................................................12
10.01 Warranty Schedule ......................................................................... 12
WARNING
SERIOUS INJURY OR DEATH may result if welding and cutting equipment is not
properly installed, used, and maintained. Misuse of this equipment and other
unsafe practices can be hazardous. The operator, supervisor, and helper must read
and understand the following safety warnings and instructions before installing
or using any welding or cutting equipment, and be aware of the dangers of the
welding or cutting process. Training and proper supervision are important for a safe
work place. Keep these instructions for future use. Additional recommended safety
and operating information is referenced in each section.
ELECTRIC SHOCK CAN CAUSE INJURY OR DEATH
Install and maintain equipment in accordance with the National Electrical Code
(NFPA 70) and local codes. Do not service or repair equipment with power on.
Do not operate equipment with protective insulators or covers removed. Service
or repair to equipment must be done by qualified and/or trained personnel only.
Do not contact electrically live parts. Always wear dry welding gloves that
are in good condition. Aluminized, protective clothing can become part of the electrical path.
Keep oxygen cylinders, chains, wires, ropes, cranes, and hoists away from any part of the
electrical path. All ground connections must be checked periodically to determine if they are
mechanically strong, and electrically adequate for the required current. When engaged in AC
welding/cutting under wet conditions or where perspiration is a factor, the use of automatic
controls for reducing the no load voltage is recommended to reduce shock hazards. Accidental
contact must be prevented when using open circuit voltage exceeding 80 volts AC, or 100
volts DC by adequate insulation or other means. When welding is to be suspended for any
length of time, such as during lunch or overnight, all electrode holders and electrodes should
be removed from the electrode holder and the power supply should be turned off to prevent
accidental contact. Keep MIG Guns, electrode holders, TIG torches, Plasma torches, and
electrodes away from moisture and water.
MESURES DE SÉCURITÉ
AVERTISSEMENT
DES BLESSURES GRAVES OU MORTELLES peuvent résulter d’une installation,
d’un usage ou d’un entretien inadéquat de l’équipement de soudage et de décou-
page. Une mauvaise utilisation de cet équipement et d’autres pratiques risquées
peuvent être dangereuses. L’opérateur, le superviseur et l’aide doivent lire et com-
prendre les avertissements et les instructions de sécurité suivantes avant d’installer
ou d’utiliser tout équipement de soudage ou de découpage et être conscients des
dangers inhérents aux processus de soudage et de découpage. Une formation et
une supervision adaptées sont importantes pour assurer un lieu de travail sûr.
Gardez ces instructions pour une utilisation future. Chaque section comporte des
informations supplémentaires de sécurité et de fonctionnement.
UN CHOC ÉLECTRIQUE PEUT CAUSER DES BLESSURES OU LA MORT
L’installation et l’entretien de l’équipement doivent être conformes au Code national
de l’électricité NFPA 70 et aux codes locaux. N’effectuez pas l’entretien ou la
réparation d’équipement en marche. N’opérez pas l’équipement sans isolateurs ou
caches de protection. L’entretien ou la réparation de l’équipement doivent être
effectués uniquement par un technicien qualifié ou par du personnel formé.
Ne touchez pas aux pièces électriques chargées. Portez toujours des gants de soudage au sec
et en bon état. Les vêtements de protection aluminisés peuvent devenir une partie du chemin
électrique. Éloignez les bouteilles d’oxygène, les chaînes, les câbles métalliques, les appareils
de levage, les treuils et les élévateurs de toute partie du circuit électrique. Toutes les liaisons de
terre doivent être vérifiées périodiquement pour déterminer si elles sont solides et appropriées au
courant demandé. En cas de soudage ou de découpage en courant alternatif dans des conditions
d’humidité ou de chaleur où l’opérateur risque de transpirer, il est recommandé d’utiliser des
contrôles automatiques pour réduire la tension à vide et ainsi diminuer les risques de choc
électrique. Lorsque le procédé de soudage et de découpage exige des valeurs de tension en
circuit ouvert dans des machines à courant alternatif supérieur à 80 volts ou dans des machines
à courant continu supérieur à 100 volts, il faut prendre des mesures pour empêcher un contact
accidentel en prévoyant une isolation adéquate ou d autres moyens. Lorsqu’il faut interrompre les
4
SAFETY AND OPERATING INSTRUCTIONS
89200016
SMOKE, FUMES, AND GASES CAN BE DANGEROUS TO YOUR HEALTH
Ventilation must be adequate to remove smoke, fumes, and gases during
operation to protect operators and others in the area. Vapors of chlorinated
solvents can form the toxic gas "Phosgene" when exposed to ultraviolet
radiation from an electric arc. All solvents, degreasers, and potential sources
of these vapors must be removed from the operating area. Use air-supplied
respirators if ventilation is not adequate to remove all fumes and gases. Oxygen supports, and
vigorously accelerates fire and should never be used for ventilation.
ARC RAYS, HOT SLAG, AND SPARKS CAN INJURE EYES AND BURN SKIN
Welding and cutting processes produce extreme localized heat and strong
ultraviolet rays. Never attempt to weld/cut without a federally compliant
welding helmet with the proper lens. A number 12 to 14 shade filter lens
provides the best protection against arc radiation. When in a confined area,
prevent the reflected arc rays from entering around the helmet. Approved
shielding curtains and appropriate goggles should be used to provide protection to others in
the surrounding area. Skin should be protected from arc rays, heat, and molten metal. Always
wear protective gloves and clothing. All pockets should be closed and cuffs sewn shut. Leather
aprons, sleeves, leggings, etc. should be worn for out-of-position welding and cutting, or for
heavy operations using large electrodes. Hightop work shoes provide adequate protection from
foot burns. For added protection, use leather spats. Flammable hair preparations should not be
used when welding/cutting. Wear ear plugs to protect ears from sparks. Where work permits,
the operator should be enclosed in an individual booth painted with a low reflective material
such as zinc oxide.
WELDING SPARKS CAN CAUSE FIRES AND EXPLOSIONS
Combustibles reached by the arc, flame, flying sparks, hot slag, and heated
materials can cause fire and explosions. Remove combustibles from the
work area and/or provide a fire watch. Avoid oily or greasy clothing as a
spark may ignite them. Have a fire extinguisher nearby, and know how to use
it. If welding/cutting is to be done on a metal wall, partition, ceiling, or roof,
precautions must be taken to prevent ignition of nearby combustibles on the
other side. Do not weld/cut containers that have held combustibles. All hollow spaces, cavities,
and containers should be vented prior to welding/cutting to permit the escape of air or gases.
Purging with inert gas is recommended. Never use oxygen in a welding torch. Use only inert
gases or inert gas mixes as required by the process. Use of combustible compressed gases
can cause explosions resulting in personal injury or death. Arcing against any compressed gas
cylinder can cause cylinder damage or explosion.
NOISE CAN DAMAGE HEARING
Noise from the air carbon-arc process can damage your hearing. Wear
protective hearing devices to ensure protection when noise levels exceed OHSA
standards. Adequate hearing protection devices must be worn by operators and
surrounding personnel to ensure personal protection against noise.
SAFETY AND OPERATING REFERENCES
1. Code of Federal Regulations (OSHA) Section 29, Part 1910.95, 132, 133, 134, 139,
251, 252, 253, 254 and 1000. U.S. Government Printing Office, Washington, DC
20402.
2. ANSI Z49.1 "Safety in Welding and Cutting".
3. ANSI Z87.1 "Practice for Occupational and Educational Eye and Face Protection".
4. ANSI Z88.2. "Standard Practice for Respiratory Protection". American National
Standards Institute, 1430 Broadway, New York, NY 10018.
5. AWS F4.1. "Recommended Safe Practices for Welding and Cutting Containers".
6. AWS C5.3. "Recommended Practices for Air Carbon-Arc Gouging and Cutting".
The American Welding Society, 550 NW Lejeune Rd., P.O. Box 351040, Miami, FL
33135.
7. NFPA 51B "Fire Prevention in Cutting and Welding Processes"
8. NFPA-7. "National Electrical Code". National Fire Protection Association, Battery Park,
Quincy, MA 02269.
9. CSA W117.2. "Safety in Welding, Cutting and Allied Processes". Canadian Standards
Association, 178 Rexdale Blvd., Rexdale, Ontario, Canada M9W 1R3.
SECTION 2: INTRODUCTION
activités de soudage pendant un certain temps, à l’heure du repas ou la nuit, par exemple, il faut
enlever toutes les électrodes du porte-électrode et mettre hors tension l’alimentation pour éviter
tout contact accidentel. Gardez les pistolets MIG, les porte-électrodes, les torches TIG, les torches
à plasma et les électrodes loin de l’humidité et de l’eau.
LA FUMÉE, LES ÉMANATIONS ET LES GAZ PEUVENT ÊTRE DANGEREUX POUR VOTRE
SANTÉ
La ventilation doit être suffisante pour enlever la fumée, les émanations et les
gaz pendant le fonctionnement de la torche afin protéger les opérateurs et les
autres personnes présentes dans la zone. Les vapeurs de solvants chlorés
peuvent former un gaz toxique appelé « Phosgène » si elles sont exposées au
rayonnement ultraviolet d un arc électrique. Il faut enlever de la zone de travail
tous les solvants, décapants et sources potentielles de ces vapeurs. Servez-vous d’appareils
respiratoires à adduction d’air si la ventilation n’est pas suffisante pour enlever toutes les
émanations et gaz. L’oxygène alimente les incendies et en accélère la propagation il ne faut
jamais l’utiliser à des fins de ventilation.
L LES RAYONS DE L’ARC, LES SCORIES ET LES ÉTINCELLES CHAUDS PEUVENT
BLESSER LES YEUX ET BRÛLER LA PEAU
Les procédés de soudage et de découpage produisent une chaleur extrême
localisée et de puissants rayons ultraviolets. N’essayez jamais de souder ou de
couper sans casque soudage conforme aux normes du gouvernement fédéral et
muni d’une lentille appropriée. Des lentilles à filtre de numéro 12 à 14 fournissent
la meilleure protection contre le rayonnement de l’arc. Dans un endroit confiné, il faut éviter que
les rayons reflétés de l’arc n’entrent autour du casque. Il faut utiliser des rideaux de protection
approuvés et des lunettes de protection appropriées pour protéger les autres personnes se
trouvant aux abords. Il faut aussi protéger la peau nue des rayons de l’arc, de la chaleur et du
métal fondu. Portez toujours des gants et des vêtements de protection. Toutes les poches doivent
être fermées et les manchettes, cousues. Il faut porter un tablier, des manches, des guêtres, etc.
en cuir pour effectuer de soudage ou de découpage et dans le cas des activités intensives
nécessitant de grandes électrodes. Les chaussures de sécurité montantes fournissent une
protection suffisante contre les brûlures aux pieds. Pour obtenir une plus grande protection,
portez des guêtres en cuir. Il ne faut pas utiliser de produits capillaires inflammables avant
d’effectuer des activités de soudage ou de découpage. Portez des bouchons d’oreilles pour vous
protéger les oreilles des étincelles. Lorsqu’il est possible de le faire dans la zone de travail,
l’opérateur doit s’isoler dans une cabine individuelle recouverte d’un revêtement à faible
réflectivité, comme l’oxyde de zinc.
LES ÉTINCELLES DE SOUDAGE PEUVENT CAUSER DES INCENDIES ET DES
EXPLOSIONS
Les combustibles atteints par l’arc, les flammes, les vols d’étincelles, les scories
chaudes et les matériaux chauffés peuvent causer des incendies et des
explosions. Enlevez les combustibles de la zone de travail ou mettez en place du
personnel de surveillance. Évitez les vêtements huileux ou graisseux, car une
étincelle peut y mettre le feu. Ayez un extincteur à proximité et sachez comment
l’utiliser. Si l’activité de soudage ou de découpage doit être fait contre un mur, une cloison, un
plafond ou un toit, il faut prendre des précautions pour d’enflammer des combustibles qui se
trouveraient à proximité, de l’autre côté. Ne soudez pas et ne coupez pas de conteneurs ayant
contenu des combustibles. Il faut aérer tous les espaces creux, les cavités et les conteneurs avant
de les soumettre au soudage ou au découpage afin d’évacuer tout l’air ou le gaz qui peut s’y
trouver. Il est recommandé d’effectuer une purge avec du gaz inerte. N’utilisez jamais d’oxygène
dans une tête de soudage. N’utilisez que des gaz inertes ou des mélanges de gaz inertes,
conformément aux exigences du procédé. L’utilisation de gaz combustibles comprimés peut
causer des explosions entraînant des blessures ou la mort. Le fait d’utiliser l’arc sur une bouteille
de gaz comprimé peut endommager la bouteille ou causer une explosion.
LE BRUIT PEUT ENDOMMAGER L’OUÏE
Le bruit du procédé de l’arc avec électrode en carbone et jet d’air peut
endommager l’ouïe. Portez un dispositif de protection de l’ouïe pour vous
protéger lorsque le niveau de bruit dépasse les normes de l’OSHA. Les
opérateurs et le personnel aux abords doivent porter un dispositif de protection de
l’ouïe approprié pour les protéger efficacement contre le bruit.
RÉFÉRENCES EN MATIÈRE DE SÉCURITÉ ET D’UTILISATION
1. Code of Federal Regulations (OSHA), section 29, partie 1910.95, 132, 133, 134, 139, 251, 252,
253, 254 et 1000. U.S. Government Printing Office, Washington, DC 20402.
2. ANSI Z49.1 « Safety in Welding and Cutting ».
3. ANSI Z87.1 « Practice for Occupational and Educational Eye and Face Protection ».
4. ANSI Z88.2. « Standard Practice for Respiratory Protection ». American National Standards
Institute, 1430 Broadway, New York, NY 10018.
5. AWS F4.1. « Recommended Safe Practices for Welding and Cutting Containers ».
6. AWS C5.3. « Recommended Practices for Air Carbon-Arc Gouging and Cutting ». The American
Welding Society, 550 NW Lejeune Rd., P.O. Box 351040, Miami, FL 33135.
7. NFPA 51B. « Fire Prevention in Cutting and Welding Processes ».
8. NFPA-7. « National Electrical Code » (code national de l’électricité). National Fire Protection
Association, Battery Park, Quincy, MA 02269.
9. CSA W117.2. « Règles de sécurité en soudage, coupage et procédés connexes ». Association
canadienne de normalisation, 178 boul. Rexdale, Rexdale, Ontario, Canada M9W 1R3.
SAFETY AND OPERATING INSTRUCTIONS
5 89200016
2.01 HOW TO USE THIS MANUAL
To ensure safe operation, read the entire manual, including the chapter on safety instructions
and warnings. Throughout this manual, the words WARNING, CAUTION, and NOTE may appear.
Pay particular attention to the information provided under these headings. These special
annotations are easily recognized as follows:
NOTE!
An operation, procedure, or background information which requires additional
emphasis or is helpful in ecient operation of the system.
!
!
CAUTION
A procedure which, if not properly followed, may cause damage to the equipment.
WARNING
A procedure which, if not properly followed, may cause injury to the operator or
others in the operating area.
2.02 RECEIPT OF EQUIPMENT
When you receive the equipment, check it against the invoice to make sure it is complete and
inspect the equipment for possible damage due to shipping. If there is any damage, notify the
carrier immediately to file a claim. Furnish complete information concerning damage claims or
shipping errors to the location in your area, listed on the back cover of this manual. Include a
full description of the parts in error.
2.03 DESCRIPTION
Tweco Spray Master MIG Guns are furnished with rear connections to fit directly into most
Miller
®
, Lincoln
®
, and Euro connection wire feeders. These guns are referred to as Direct Plug
MIG Guns. Tweco Spray Master MIG guns are also furnished with the time-proven MIG-Kwik
connection. The MIG-Kwik connection, when utilized with a Tweco adapter kit, allows a Tweco
Spray Master MIG gun to be installed on almost any wire feed system. Call Tweco Customer
Care for a listing of available adapter kits.
Miller is registered trademark of Illinois Tool Works, Inc. Lincoln is a registered trademark of Lincoln Electric Co. The
aforementioned registered trademarks are no way affiliated with Tweco Products, Inc. or ESAB. Tweco Spray Master is a
registered trademark of ESAB.
SECTION 3: MIG GUN
SPECIFICATIONS
3.01 MIG GUN CLASSIFICATION
Process MIG/MAG welding
Method of Guidance Manually guided
Type of Cooling Air
Type of Shielding Gas All types
3.02 DUTY CYCLE
Spray Master with VELOCITY2 MIG Guns (250, 350, and 450 Amps) with mixed gas are rated
at 80% duty cycle per IEC 60974-7.
3.03 MIG GUN PART NUMBER IDENTIFICATION
NOTE!
Spray Master MIG guns, as a general rule, have a specic nomenclature incorpo-
rated within each part number to help determine the wire size of each MIG gun.
Example Part Number:
SMV315116
Spray Master
with VELOCITY2
350 AMP, 15 foot (5 M) cable
1/16" Wire Capacity
(1,6mm)
SECTION 4: MIG GUN INSTALLATION
NOTE!
Be certain that the end user (welder, operator, or helper) reads and understands
these instructions. Be certain that the welder also reads Section 2 "Safety Precau-
tions."
WARNING
Electric shock can cause injury or death.
POWER
SOURCE
WIRE FEEDER
GROUND
WORK PIECE
GUN
Figure 1: Standard MIG Gun Installation
4.01 DIRECT PLUG MIG GUN INSTALLATION
Direct plug MIG guns install by directly inserting the rear connector plug into the feeder wire
guide outlet (see figure 2) and tightening the plug retaining screw. All models of MIG guns,
except the Euro-Kwik guns, require a control wire assembly to attach the MIG gun trigger
leads to the feeder. The control wire assemblies plug into the rear connector case of the MIG
gun, and into the control wire receptacle on the feeder. Euro-Kwik connections are installed by
inserting the gun connection into the feeder receptacle, aligning the conduit plug first, then the
gas plug. Push until all fittings are seated, then tighten the nut hand tight as shown in figure 3.
Figure 2
Figure 3
SECTION 5: SPRAY MASTER WITH
6
SAFETY AND OPERATING INSTRUCTIONS
89200016
VELOCITY2 MAINTENANCE
This section discusses servicing and or replacing various components of the Spray Master MIG Gun.
WARNING
Disconnect power from MIG Gun before servicing.
5.01 INSTALLING OR REPLACING VELOCITY2 CONTACT TIP
Avoid excessive consumables wear by periodically rotating tips.
Increase consumables life by occasionally rotating tips.
!
!
CAUTION
While nozzle and contact tip are removed, maintain an adequate distance of the wire from metal objects to avoid burnbacks to conduit or conductor tube.
1. (REPLACING) Remove worn nozzle and tip. (Clean nozzle if reusing.)
2. (NEW INSTALL) Slide new contact tip over the conduit end and into the conductor tube
end.
3. Replace the nozzle. Hand tighten (Nozzle secures tip).
NOTE!
For proper operation the nozzle MUST be tight.
4. Trim wire to desired stick out.
The MIG gun is now ready operation.
5.02 CONDUIT IDENTIFICATION
The procedure for removal and installation of a wire conduit is similar for all Tweco MIG guns.
Conduits may be identified by the type of conduit stop and the part number marking on each
conduit stop.
Example Part Number:
44-116-15
44 Series
1/16" (1,6mm) Wire Capacity
Liner length in feet
CONDUIT REMOVAL
1. Lay the MIG gun out on a table or on the floor in a straight line. Make sure the gun
is fully extended and all twists in the cable are removed.
2. Remove the nozzle and loosen the conduit set screw in the front of the gun. This is
usually located at the front of the handle. Then loosen the conduit set screw in the
rear connector plug.
Conduit set screw
NOTE!
On Miller® Direct Plug MIG guns, remove the nipple on the end of the connector
plug. On Euro-Kwik connections, remove the conduit retaining cap.
3. Remove the contact tip.
4. Grip the conduit stop and remove the conduit with a twisting motion. On Miller
®
Direct Plug MIG guns, twisting the rear of the gun approximately one revolution
clockwise will raise the conduit stop out of the connector plug recess.
CONDUIT INSTALLATION
1. Uncoil the conduit and lay it in a straight line. Insert the conduit into the rear connector
plug. Push the conduit into the gun with short strokes. If the conduit hangs up, twist
the conduit counterclockwise or gently whip the cable while applying pressure to the
conduit.
2. The conduit liner will need to be cut to length. This can be done by cutting the
conduit to match the one removed or inserting the new liner through the MIG gun
and trimming the conduit extending from the conductor tube to the appropriate
length using one of two methods.
Conductor tube end
Score on nozzle end
Nozzle
CUT
Method I
Conduit Trim Length
3/8”
(9 mm to 10 mm)
Conductor end
CUT
Method II
3. When the conduit is completely in the gun, tighten the rear conduit set screw.
On Miller
®
guns, reinstall the nipple. On Euro-Kwik® guns, reinstall the conduit
retaining cap.
4. Inspect the cut conduit end to remove burrs because they could interfere with wire
feeding or conflict with the conduit seating inside the VELOCITY2 tip. Remove burrs
with a file or side cutter.
5. Insert the contact tip and HAND tighten the nozzle.
The MIG gun is now ready to be reinstalled on the feeder.
5.03 INSTALLING/REPLACING STAINLESS STEEL SLEEVE
/ LOCK COLLAR
Tweco offers replacement conductor tubes, refer to Section 8, that has a stainless steel sleeve
& lock collar on the end of the tube to accept the VELOCITY2 front end wear parts. The
Stainless Steel Sleeve is held in place by one screw (some models have two screws) and the
sleeve holds the lock collar assembly in place.
SCREW (SLEEVE)
Lock collar and wave spring are held
in place by the stainless steel sleeve.
STAINLESS STEEL SLEEVE
CONDUCTOR TUBE END
Tighten until screw head bottoms out.
1. Remove the front end consumables from the conductor tube.
2. Using a 5/64" Hex wrench remove the Sleeve Screw(s) and slide the Stainless
Steel Sleeve off the conductor tube end.
Notice that the Lock Collar assembly is now loose.
3. If the Lock Collar assembly is being replaced, remove the assembly now.
a) Clean conductor tube end and lock collar seat on the conductor tube.
b) Assemble the Lock Collar parts in this order and slide onto the conductor
tube end.
SAFETY AND OPERATING INSTRUCTIONS
7 89200016
Lock Collar
Spring Washer Snap Ring
4. Slide the Stainless Steel Sleeve onto the conductor tube end.
5. Align the set screw with the threaded hole in the conductor tube and tighten until
the screw bottoms out. Do not overtighten.
The conductor tube Stainless Steel Sleeve replacement is complete. Trim the conduit
and install the consumables.
5.04 REPLACE CONDUCTOR TUBE
The conductor tube is attached to the MIG Gun handle by two set screws on the side of the
handle. To remove:
1. Remove the front end consumables from the conductor tube.
Loosen the conduit liner set screw with a 5/64" hex wrench supplied and then
loosen the socket head cap screw securing the conductor tube in place inside the
handle with a 5/32" hex wrench. Refer to the figure below.
2. Remove conductor tube.
Conductor Tube set screw
Conduit Liner set screw
3. Mount the conductor tube O-ring on the end of the conductor tube.
Slide the tube over the liner and insert into the brass connection within the handle.
Tighten the socket head cap screw wrench tight using the 5/32" hex wrench.
4. Tighten the conduit set screw down against the liner. Do not overtighten to avoid
damages the liner.
5. Check the length of conduit extending from the conductor tube front end and
adjust if necessary.
There are two methods of trimming the conduit. See "Conduit Installation" on page
6.
SECTION 6: CABLEHOZ® REPAIR
6.01 CABLEHOZ® REPAIR
If you should find it necessary to repair Cablehoz connection(s), repair instructions can be found at www.Tweco.com our website.
RED
WHITE
BLACK
BLACK
RED
WHITE
BLACK
BLACK
TRIGGER
NOT USED
NOT USED
BLUE
BROWN
CONTROL WIRE
CABLEHOZ
{
A. Back-End Repair
8
SAFETY AND OPERATING INSTRUCTIONS
89200016
1. Disassemble the rear case to expose the rear connector assembly and pull the assembly away from the rear case.
2. Cut the Cablehoz to remove the damaged area.
3. Use replacement connector assembly:
250 Amp - Part No. MS172-RK (Stock No. 2060-2134)
350 Amp - Part No. MS174-RK (Stock No. 2060-2135)
4. Measure back 2-1/2" (63.5mm) from the end of the Cablehoz and cut away the outer jacket of the cable, being careful not to cut the
copper strands and or lead wires.
5. Pull the copper strands and lead wires away from the inner
core tube that’s exposed and cut away leaving approximately
¼" (6.35mm) past the end of the end of the Cablehoz.
6. Cut the copper strands to a length of ¾" (19.05mm) while
leaving the wire leads intact.
7. Thread the pressure nut onto the replacement rear connector until it bottoms out and then slide the sleeve over the connector. Note:
Make sure that the end with the bevel on the inside diameter goes on rst allowing the opposite end with a ¾" (19.05mm) to be
facing the Cablehoz when assembled.
8. Insert the replacement connector into the inner core tube
of the Cablehoz. It’s recommended to use a small amount of
lubricant to help the connector to slide into the tube. The core
tube should bottom out against the shoulder, approximately
15/16" (23.8mm) onto the connector.
9. Push the copper strands underneath the sleeve. It’s recommended that a 1/8" glass lament tape be wrapped around the exposed
copper to keep the copper strands together.
10. Begin to turn the pressure nut counter-clockwise which will
force the copper strands & sleeve against the machined taper
on the connector.
11. Torque the pressure nut to 250 inch pounds (+/-50 inch pounds).
12. Position the metal Band-it strap that came with the repair kit 1/4" (6.4mm) from the front edge of the outer jacket on the
Cablehoz. You will need to purchase the tool to secure the clamp down against the Cablehoz, Part No. 136TOOL (Stock No.
2060-2691) and follow the manufacturer's procedure included with this tool.
13. Connect lead wires accordingly.
14. Reassemble the rear case.
B. Front-End Repair
1. Disassemble the rear case to expose the rear connector assembly and pull the assembly away from the rear case.
2. Cut the Cablehoz to remove the damaged area.
3. Use replacement connector assembly:
250 Amp - Part No. MS102-RK (Stock No. 2060-2132)
350 Amp - Part No. MS104-RK (Stock No. 2060-2133)
4. Measure back 2-1/2" (63.5mm) from the end of the Cablehoz and cut away the outer jacket of the cable, being careful not to cut the
copper strands and or lead wires.
5. Pull the copper strands and lead wires away from the inner
core tube that’s exposed and cut away leaving approximately
¼" (6.35mm) past the end of the end of the Cablehoz.
6. Cut the copper strands to a length of ¾" (19.05mm) while
leaving the wire leads intact.
7. Thread the pressure nut onto the replacement rear connector until it bottoms out and then slide the sleeve over the connector. Note:
Make sure that the end with the bevel on the inside diameter goes on rst allowing the opposite end with a ¾" (19.05mm) to be
facing the Cablehoz when assembled.
8. Insert the replacement connector into the inner core tube of
the Cablehoz. It’s recommended to use a small amount of
lubricant to help the connector to slide into the tube. The core
tube should bottom out against the shoulder, approximately
15/16" (23.8mm) onto the connector.
9. Push the copper strands underneath the sleeve. It’s recommended that a 1/8" glass lament tape be wrapped around the exposed
copper to keep the copper strands together.
10. Begin to turn the pressure nut counter-clockwise which will
force the copper strands & sleeve against the machined taper
on the connector.
11. Torque the pressure nut to 250 inch pounds (+/-50 inch pounds).
12. Position the metal Band-it strap that came with the repair kit 1/4" (6.4mm) from the front edge of the outer jacket on the Cablehoz.
You will need to purchase the tool to secure the clamp down against the Cablehoz, Part No. 136TOOL (Stock No. 2060-2691) and follow
the manufacturer's procedure included with this tool.
13. Connect lead wires accordingly.
14. Re-assemble the front end back into the handle halves.
SECTION 7: TROUBLESHOOTING
Contact tips and nozzles should be cleaned frequently. Spatter buildup may cause bridging between nozzle and tip. This could cause electrical shorting between the nozzle and work piece as
well as poor or improper gas flow. Regularly inspect the conductor tube, handle, cable, and other parts of the MIG Gun for abrasion, cuts, or undue wear. Replace or repair any parts found
deficient. Refer to www.Tweco.com for MIG Gun troubleshooting chart(s).
SAFETY AND OPERATING INSTRUCTIONS
9 89200016
SECTION 8: CONSUMABLES
8.01 TIPS AND NOZZLES
VELOCITY2 Nozzle Identification
VNM50FS
VELOCITY2
Nozzle
Blank=Standard Recess
F=Flush
2PC=Two Piece
R=Recess 1/4" (6.35 mm)
FAS=Spot Weld
FC=Flux Core
S= Small (Light Duty)
M=Medium Duty
H=Heavy Duty
ET=Extended Taper
Orifice Opening Size:
37=3/8” 62=5/8”
50=1/2” 75=3/4”
Blank= Fixed Threaded
S=Adjustable Slip
Nozzle Convention
2 Knurl Rings VNM
3 Knurl Rings VNH
4 Knurl Rings VNET
Medium Duty Heavy Duty
VELOCITY2 Contact Tip Identification
VTMA30
VELOCITY2
Tip
S= Small (Light Duty)
M=Medium Duty
H=Heavy Duty
ET=Extended Taper
A=Alum
Blank=Other
Wire Size: 364=3/64”
23=0.023” 116=1/16”
30=0.030” 564=5/64”
35=0.035” 332=3/32”
40=0.040” 764=7/64”
45=0.045” 18=1/8”
Contact Tip Convention
2 Rings VTM
3 Rings VTH
4 Rings VTET
Medium Duty Heavy Duty
Medium Duty Contact Tips Heavy Duty Contact Tips Extended Taper Contact Tips
Description Part No. Stock No. Description Part No. Stock No. Description Part No. Stock No.
.023" (0.6 mm)
VTM23
1160-1750 .030" (0.8 mm)
VTH30
1160-1760 .030" (0.8 mm)
VTET30
1160-1772
.030" (0.8 mm)
VTM30
1160-1751 .035" (0.9 mm)
VTH35
1160-1761 .035" (0.9 mm)
VTET35
1160-1773
.035" (0.9 mm)
VTM35
1160-1752 .040" (1.0 mm)
VTH40
1160-1762 .040" (1.0 mm)
VTET40
1160-1774
.040" (1.0 mm)
VTM40
1160-1753 .045" (1.2 mm)
VTH45
1160-1763 .045" (1.2 mm)
VTET45
1160-1775
.045" (1.2 mm)
VTM45
1160-1754 3/64" (1.2 mm)*
VTHA364*
1160-1764 3/64" (1.2 mm)*
VTETA364*
1160-1776
3/64" (1.2 mm)*
VTMA364*
1160-1755 .052" (1.3 mm
)
VTH52
1160-1765 .052" (1.3 mm)
VTET52
1160-1777
.052" (1.3 mm)
VTM52
1160-1756 1/16" (1.6 mm)
VTH116
1160-1766 1/16" (1.6 mm)
VTET116
1160-1778
1/16" (1.6 mm)
VTM116
1160-1757 1/16" (1.6 mm)*
VTHA116*
1160-1767
Extended HD Taper Contact Tips
1/16" (1.6 mm)*
VTMA116*
1160-1758 5/64" (2.0 mm)
VTH564
1160-1768
5/64" (2.0 mm)
VTM564
1160-1759 3/32" (2.4 mm)
VTH332
1160-1769
Description Part No. Stock No.
7/64" (2.8 mm)
VTH764
1160-1770 .035" (0.9 mm)
VTHET35
1160-1780
* For Aluminum
1/8" (3.2 mm)
VTH18
1160-1771 .045" (1.2 mm)
VTHET45
1160-1782
.052" (1.3 mm)
VTHET52
1160-1784
1/16" (1.6 mm)
VTHET
116
1160-1785
Medium Duty Nozzles
Description Part No. Stock No.
1/2" (12.7 mm) Threaded Nozzle Recess
VNM50
1240-1857
1/2" (12.7 mm) Threaded Nozzle Flush
VNM50F
1240-1856
5/8" (15.9 mm) Threaded Nozzle Recess
VNM62
1240-1854
5/8" (15.9 mm) Threaded Nozzle Flush
VNM62F
1240-1855
3/4" (19.1 mm) Threaded Nozzle Recess
VNM75
1240-1852
3/4" (19.1 mm) Threaded Nozzle Flush
VNM75F
1240-1853
1/2" (12.7 mm) Slip Nozzle
VNM50S
1240-1859
5/8" (15.9 mm) Slip Nozzle
VNM62S
1240-1860
3/4" (19.1 mm) Slip Nozzle
VNM75S
1240-1863
Slip Nozzle Base
VNS
1240-1864
1/2" (12.7 mm) Slip Nozzle Cone Only
VNM50SC
1240-1861
5/8" (15.9 mm) Slip Nozzle Cone Only
VNM62SC
1240-1862
3/4" (19.1 mm) Slip Nozzle Cone Only
VNM75SC
1240-1865
Flux Core Nozzle
VNLFC
1240-1892
5/8" (15.9
mm) Spot Nozzle
VNM62FAS
1240-1866
3/4" (19.1 mm) Spot Nozzle
VNM75FAS
1240-1868
Extended Taper Nozzle
Extended Taper Nozzle
VNET37F
1240-1897
Heavy Duty Nozzles
Description Part No. Stock No.
5/8" (15.9 mm) Threaded Nozzle Recess
VNH62
1240-1877
5/8" (15.9 mm) Threaded Nozzle Flush
VNH62F
1240-1878
3/4" (19.1 mm) Threaded Nozzle Recess
VNH75
1240-1875
3/4" (19.1 mm) Threaded Nozzle Flush
VNH75F
1240-1876
5/8" (15.9 mm) Slip Nozzle
VNH62S
1240-1893
3/4" (19.1 mm) Slip Nozzle
VNH75S
1240-1894
Slip Nozzle Base
VNS
1240-1864
1/2” (12.7mm) 2 Piece Nozzle Cone Only Recess
VNH50RC
1240-1867
5/8" (15.9 mm) Slip Nozzle Cone Only
VNH62SC
1240-1895
3/4" (19.1 mm) Slip Nozzle Cone Only
VNH75SC
1240-1896
5/8" (15.9 mm) 2 Piece Nozzle Assembly Recess
VNH622PC
1240-1880
5/8" (15.9 mm) 2 Piece Nozzle Cone Only Recess
VNH62C
1240-1884
5/8" (15.9 mm) 2 Piece Nozzle Assembly Flush
VNH62F2PC
1240-1881
5/8" (15.9 mm) 2 Piece Nozzle Cone Only Flush
VNH62FC
1240-1885
3/4" (19.1 mm) 2 Piece Nozzle Assembly Recess
V
NH752PC
1240-1882
3/4" (19.1 mm) 2 Piece Nozzle Cone Only Recess
VNH75C
1240-1886
3/4" (19.1 mm) 2 Piece Nozzle Assembly Flush
VNH75F2PC
1240-1883
3/4" (19.1 mm) 2 Piece Nozzle Cone Only Flush
VNH75FC
1240-1887
Nozzle Retainer
VNH2PC
1240-1879
Flux Core Tip Holder & Insulator
VNSFC
1220-1207
Note: VELOCITY2 medium and heavy duty contact tips and nozzles are for use
with Tweco Classic
®
No. series and Spray Master
®
series MIG Guns.
Some parts may not be available at this time.
10
SAFETY AND OPERATING INSTRUCTIONS
89200016
8.02 CONDUIT
250 AMP
Length
Wire Size
.035" - .045" (1,0mm - 1,2)mm
Part No. Stock No.
12 Ft
15 Ft
42-4045-15 1420-1123
20 Ft
25 Ft
42-4045-25 1420-1125
350 AND 450 AMP
Length
Wire Size
.052" - 1/16" (1,3mm - 1,6mm)
350 Amp 450 Amp
Part No. Stock No. Part No. Stock No.
10 Ft See 15 Ft See 15 Ft
12 Ft See 15 Ft See 15 Ft
15 Ft
44-116-15 1440-1113 44-116-15 1440-1113
20 Ft See 20 Ft See 20 Ft
25 Ft
44-116-25 1440-1115
8.03 CONDUCTOR TUBE
STANDARD REPLACEMENT CONDUCTOR TUBE
(250, 350, and 450 Amp)
Part Number Stock Number
SMVCTLS60 1240-1377
SMVCTLS45 1240-1376
SMVCTLS60LM 1640-1403
SMVCTLS45LM 1640-1402
OPTIONAL REPLACEMENT CONDUCTOR TUBE (WITH STAINLESS STEEL SLEEVE)
(250, 350, and 450 Amp)
Part Number Stock Number
SMVCT60SS 1240-1378
SMVCT45SS 1240-1379
SMVCT60LMSS 1640-1404
SMVCT45LMSS 1640-1405
SMVCT180 1240-1375
SAFETY AND OPERATING INSTRUCTIONS
11 89200016
SECTION 9: REPLACEMENT PARTS
6
11
3b
3c
3a
16
17
18
4a
5
10
10
4c
16
19
22
22
23
24
25
20
21
4b
1
2
1
1a
2b
2c
2a
2e
2d
1b
1c
Tweco
®
Style Rear Connector
Miller
®
Style Rear Connector
Lincoln
®
Style Rear Connector
Euro-Kwik Style Rear Connector
Refer to Section 8 for Nozzles and Contact Tips
Refer to 8.01 Tips and Nozzles for tip and nozzle part numbers and descriptions.
Refer to 8.02 Conduit for conduit part numbers and descriptions.
Refer to 8.03 Conductor Tube for conductor tube part numbers and descriptions.
12
SAFETY AND OPERATING INSTRUCTIONS
89200016
1750-2119
1750-2120
MS512X
MS515
1750-2116
1750-2117
1750-2118
——
122FMS
2020-2123
122FMS
2020-2123
SMVCTLS60 1240-1377 SMVCTLS60 1240-1377
SMVCTLS45 1240-1376 SMVCTLS45 1240-1376
SMVCTLS60LM 1640-1403 SMVCTLS60LM 1640-1403
SMVCTL45LM 1640-1402 SMVCTL45LM 1640-1402
VCTLJBLK 1640-1409 VCTLJBLK 1640-1409
VCTLSI 1640-1408 VCTLSI 1640-1408
VCTLS015 1640-1410 VCTLS015 1640-1410
SMVCT60SS 1240-1378 SMVCT60SS 1240-1378
SMVCT45SS 1240-1379 SMVCT45SS 1240-1379
SMVCT60LMSS 1640-1404 SMVCT60LMSS 1640-1404
SMVCT45LMSS 1640-1405 SMVCT45LMSS 1640-1405
SMVCT180 1240-1375 SMVCT180 1240-1375
VCTLSL 1640-1397 VCTLSL 1640-1397
VCTLSLK 1640-1398 VCTLSLK 1640-1398
VCTLSPR 1640-1399 VCTLSPR 1640-1399
PMA64RS 1640-1396 PMA64RS 1640-1396
VCT41CS 2040-2048 VCT41CS 2040-2048
SMV83 2060-2083 SMV84 2060-2084
SMV83DS 2060-2077 SMV84DS 2060-2078
SMV83LC 2060-2080 SMV84LC 2060-2081
ELC94 2060-2647 ELC94 2060-2647
MS94LC 2060-2693 MS94-LC 2060-2693
MS94RSW 2060-2694 MS94-RSW 2060-2694
ELC94BL 2060-2671 ELC94-BL 2060-2671
2020-2123
1240-1377
1240-1376
1640-1403
1640-1402
1640-1409
1640-1408
1640-1410
1240-1378
1240-1379
1640-1404
1640-1405
1240-1375
1640-1397
1640-1398
1640-1399
1640-1396
2040-2048
2060-2082
—
2060-2079
2060-2647
2060-2693
—
2060-2671
122FMS
SMVCTLS60
SMVCTLS45
SMVCTLS60LM
SMVCTL45LM
VCTLJBLK
VCTLSI
VCTLS015
SMVCT60SS
SMVCT45SS
SMVCT60LMSS
SMVCT45LMSS
SMVCT180
VCTLSL
VCTLSLK
VCTLSPR
PMA64RS
VCT41CS
SMV82
—
SMV82LC
ELC94
MS94LC
—
ELC94-BL
1
Conductor Tube–60°
Conductor Tube–45°
Conductor Tube–60° LM
Conductor Tube–45° LM
Silicone Tubing (Sold/Foot)
Insulator, VELOCITY2 Conductor Tube Assy.
O-Ring (Pkg. Of 10 each)
Threaded Stainless Sleeve
Nozzle Collar
Wave Spring
Wave Spring Retainer
Sleeve Screw
Dual Schedule Rocker Switch
Trigger Blade Assembly
1a
1b
1c
2
Conductor Tube–60° (Stainless Steel Sleeve)
Conductor Tube–45° (Stainless Steel Sleeve)
Conductor Tube–60° LM (Stainless Steel Sleeve)
Conductor Tube–45° LM (Stainless Steel Sleeve)
Conductor Tube–180° (Stainless Steel Sleeve)
2a
2b
2c
2d
2e
3c
3b
3a Handle–Standard Spray Master
Handle–Dual Schedule (Rocker Switch)
Handle–Locking Trigger
4b
4a Trigger–Standard & Dual Schedule
Trigger–Locking
4c
5
2020-2152
2060-2646
2020-2123
2060-2690
2060-2131
2060-2035
2060-2041
2060-2006
2060-2140
9900-1150
152
ELC124FM
136
MS144
——
MS512
MS515
MS525
235RSSR
C6RC
X6RC
MS354-DSM
TCR50
2020-2152
2060-2646
2020-2123
2060-2690
2060-2131
1730-2035
1730-2036
1730-2037
1730-2038
2060-2035
2060-2133
2060-2135
2040-2181
2060-2041
2060-2006
2060-2140
9900-1150
152
ELC124FM
136
MS144
MS310
MS312
MS315
MS325
235RSSR
MS104-RK
MS174-RK
174X-M
C6RC
X6RC
MS354-DSM
TCR50
2020-2152
2060-2646
2020-2123
2060-2690
2060-2131
1720-2115
1720-2116
1720-2117
2060-2035
2060-2132
2060-2134
2020-2181
2060-2041
2060-2006
2060-2140
9900-1150
152
ELC124FM
136
MS144
MS210
MS212
MS215
235RSSR
MS102-RK
MS172-RK
172X-M
C6RC
X6RC
MS354-DSM
See Section 8
See Section 8
See Section 8
See Section 8
See Section 8
See Section 8
TCR50
10 ft (3 m) Cablehoz
®
Assembly (Direct Plug)
12 ft (3.6 m) Cablehoz Assembly (Direct Plug)
15 ft (4.6 m) Cablehoz Assembly (Direct Plug)
25 ft (7.6 m) Cablehoz Assembly (Direct Plug)
10 ft (3 m) Cablehoz Assembly (Euro)
12 ft (3.6 m) Cablehoz Assembly (Euro)
15 ft (4.6 m) Cablehoz Assembly (Euro)
25 ft (7.6 m) Cablehoz Assembly (Euro)
Rear Cable Connector Repair Kit (Direct Plug)
Rear Cable Connector Repair Kit (Euro)
Rear Case (Direct Plug)
Rear Case (Euro)
®
Control Wire
Gun Hanger
Binder Posts & Screws (Standard & Locking)
Binder Posts & Screws (Dual Schedule)
Cable Clamp
Front Strain Relief Spring & Cap
Rear Strain Relief Spring & Cap
Front Cable Connector Repair Kit (Direct Plug & Euro)
Miller
Connector Plug
Conduit Assembly
Protective Cable Wrap, 50 ft (15.2 m) per box
6
10
11
16
17
18
19
20
21
22
23
24
25
NS
——
——
——
——
——
——
——
——
——
——
——
——
——
# Description
Spray Master 250 Amp Spray Master 350 Amp Spray Master 450 Amp
Stock No. Stock No. Stock No.Part No. Part No. Part No.
SECTION 10: STATEMENT OF WARRANTY
10.01 WARRANTY SCHEDULE
The warranty is effective below for the time stated in the Warranty Schedule beginning on the date that the authorized distributor delivers the products to the purchaser. ESAB reserves the right
to request documented evidence of date of purchase.
MIG Torches and Arc Accessories Parts / Labor
All MIG Gun products 30 days from date purchaser purchases from seller. 30 days / NA
www.esab.eu
©2015 Welding and Cutting Products
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna-Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Heist-op-den-Berg
Tel: +32 70 233 075
Fax: +32 15 257 944
BULGARIA
ESAB Kft Representative Oce
Soa
Tel/Fax: +359 2 974 42 88
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Vamberk
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
GERMANY
ESAB Welding & Cutting GmbHZweigstelle
Langenfeld
Tel.: +49 2173 3945 0
Fax.: +49 2173 3945 218
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
ITALY
ESAB Saldatura S.p.A.
Bareggio (Mi)
Tel: +39 02 97 96 8.1
Fax: +39 02 97 96 87 01
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
ROMANIA
ESAB Romania Trading SRL
Bucharest
Tel: +40 316 900 600
Fax: +40 316 900 601
RUSSIA
LLC ESAB
Moscow
Tel: +7 (495) 663 20 08
Fax: +7 (495) 663 20 09
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
SPAIN
ESAB Ibérica S.A.
San Fernando de Henares
Tel: +34 91 878 3600
Fax: +34 91 802 3461
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
ESAB international AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
SWITZERLAND
ESAB AG
Baar
Tel.: +41 44 741 25 25
Fax.: +41 44 740 30 55
UKRAINE
ESAB Ukraine LLC
Kiev
Tel: +38 (044) 501 23 24
Fax: +38 (044) 575 21 88
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
BRAZIL
ESAB S.A.
Contagem-MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
USA
ESAB Welding & Cutting Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
Asia/Pacic
AUSTRALIA
ESAB South Pacic
Archereld BC QLD 4108
Tel: +61 1300 372 228
Fax: +61 7 3711 2328
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 2326 3000
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 45 670 7073
Fax: +81 45 670 7001
MALAYSIA
ESAB (Malaysia) Snd Bhd
USJ
Tel: +603 8023 7835
Fax: +603 8023 0225
SINGAPORE
ESAB Asia/Pacic Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
Africa
EGYPT
ESAB Egypt
Dokki-Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
SOUTH AFRICA
ESAB Africa Welding & Cutting Ltd
Durbanvill 7570 - Cape Town
Tel: +27 (0)21 975 8924
Distributors
For addresses and phone numbers to our
distributors in other countries, please visit our
home page
www.esab.eu
ESAB subsidiaries and representative oces
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
Tweco Spray Master MIG Guns Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Tweco Tweco Spray Master MIG Guns with VELOCITY2 Manuel utilisateur
-
-
Tweco Classic No. Series Mig Guns Manuel utilisateur
-
Tweco Classic No. Series Mig Guns Manuel utilisateur
-
Tweco Classic Serial No. Mig Guns Manuel utilisateur
-
Tweco Classic No. Series Mig Guns Manuel utilisateur
-
Tweco Classic No. Series Mig Guns with Velocity Consumables Manuel utilisateur
-
Tweco TWECO® FUSION™250 Air-Cooled Mig Gun 250 AMP Manuel utilisateur
-
Tweco Classic Serial No. Mig Guns Manuel utilisateur
-
