Thermador DWHD771WFM Mode d'emploi

Use and care

GUIDE

THERMADOR.COM

Dishwasher

DWHD771W**

Table of

CONTENTS

Table of contents

en-us Operati ng instructions

Safety Definitions ............................................................ 4

IMPORTANT SAFETY INSTRUCTIONS ........................... 5

Causes of Damage .......................................................... 7

Getting Started ............................................................... 8

Home Connect™ .......................................................... 11

Water softening system / special salt * ......................... 13

Rinse Aid ....................................................................... 15

Loading the Dishwasher ................................................ 16

Detergent ...................................................................... 20

Dishwasher Cycles ........................................................ 22

Dishwasher Cycle Options ............................................ 23

Operating the Dishwasher ............................................ 25

Care and Maintenance .................................................. 28

Troubleshooting ............................................................ 32

Customer Service .......................................................... 37

Statement of Limited Product Warranty ....................... 38

.

4

Safety Definitions

9 WARNING

This indicates that death or serious injuries may

occur as a result of non-observance of this warning.

9 CAUTION

This indicates that minor or moderate injuries may

occur as a result of non-observance of this warning.

NOTICE: This indicates that damage to the appliance or

property may occur as a result of non-compliance with

this advisory.

Note: This alerts you to important information and/or

tips.

5

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFET Y I NST RUCT I ONSRE AD AND SAV E THESE INSTRUCTIONS

This dishwasher is provided with Installation Instructions

and this Use and Care Manual. Read and understand all

instructions before using the dishwasher.

This dishwasher is intended for use up to a maximum

altitude of 13,000 ft (4,000 meters) above sea level.

To reduce the risk of fire, electrical shock,

or serious injury, observe the following:

Risk of fire, electrical shock, or serious injury

WARNING

RISK OF INJURY OR DEATH

Misuse of the dishwasher can result in serious injury or

death. Do not use the dishwasher in any way not covered

in this manual or for any purpose other than those

explained in the following pages.

WARNING

RISK OF INJURY

Severe injury and/or product damage could result from

the use of unauthorized service technicians or non-

original replacement parts. All repairs must be performed

by an authorized service technician using only original

equipment factory replacement parts.

WARNING

RISK OF ELECTRICAL SHOCK OR FIRE

Electrical shock or fire could result if the electrical supply

for the dishwasher covered in this manual is incorrectly

installed or if the dishwasher has been improperly

grounded. Do not use the dishwasher covered in this

manual unless you are certain the electrical supply has

been correctly installed and the dishwasher has been

properly grounded.

WARNING

HEALTH HAZARD

Never use harsh chemicals to clean your dishwasher.

Some bleach-based products can damage your

dishwasher and may present health hazards!

GROUNDING INSTRUCTIONS

This appliance must be grounded to a metal, permanent

wiring system or an equipment grounding conductor

must be run with the circuit conductors and connected to

the equipment grounding terminal or lead on the

dishwasher. See the Installation Instructions included

with this dishwasher for more information on electrical

requirements.

WARNING

RISK OF ELECTRIC SHOCK

This appliance must be grounded. In the event of a

malfunction or breakdown, grounding will reduce the risk

of electric shock by providing a path of least resistance

for electric current. This appliance is equipped with a

cord having an equipment-grounding conductor.

Improper connection of the equipment-grounding

conductor can result in risk of electric shock. Check with

a qualified electrician if you are in doubt whether the

appliance is properly grounded.

Safe Operation

Use this dishwasher only for its intended function, which

is the washing of household dishware and kitchenware

rated as dishwasher safe.

Use only detergents or rinsing agents recommended for

use in a dishwasher, and keep them out of the reach of

children.

CAUTION

When loading items to be washed:

▯ Locate sharp items so they are not likely to

damage the door seal.

▯ Load knives and other sharp utensils with their

HANDLES UP to reduce the risk of cut-type

injuries.

▯ Do not wash plastic items unless they are marked

“dishwasher safe” or the equivalent. For plastic

items not so marked, check the manufacturer’s

recommendations.

▯ Do not operate your dishwasher unless all

enclosure panels are in place.

▯ Do not tamper with or override controls and

interlocks.

Do not abuse, sit or stand on the door or dish racks of

the dishwasher.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

6

WARNING

RISK OF INJURY

To avoid risk of injury, always use caution when opening

the door during or following a wash cycle as hot water or

steam may escape. Do not fully open the door until water

noises have stopped and steam has subsided.

To reduce risk of injury, do not allow children to play in or

on the dishwasher.

When children become old enough to operate the

appliance, it is the responsibility of the parents/legal

guardians to ensure the children are instructed in safe

practices by qualified persons.

NSF/ANSI 184 Certified residential dishwashers are not

intended for licensed food establishments.

Proper Care and Maintenance

WARNING

RISK OF EXPLOSION

Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for two weeks or more. Hydrogen gas is explosive.

Before using a dishwasher that is connected to a hot

water system that has been unused for two weeks or

longer, turn on all hot water faucets and let the water flow

from each for several minutes. This will release any

accumulated hydrogen gas. As the gas is explosive, do

not smoke or use an open flame during this time.

Remove the dishwasher door to the washing

compartment when removing an old dishwasher for

service or discarding.

To avoid floor damage and possible mold growth, do not

allow wet areas to remain around or under the

dishwasher.

Note: To avoid dishwasher damage, do not allow water

to remain in your dishwasher systems through extended

periods of freezing temperatures. Freezing temperatures

can damage the water fill valve and potentially other

components of your dishwasher.

NOTICE: It is highly recommended for the end user to

become familiar with the procedure to shut off the

incoming water supply and the procedure to shut off the

incoming power supply. See the Installation Instructions

or contact your installer for more information.

State of California Proposition 65

Warning:

WARNING

This product can expose you to chemicals including vinyl

chloride, which is known to the State of California to

cause cancer and birth defects or other reproductive

harm. For more information go to

www.P65Warnings.ca.gov.

7

Causes of Damage

NOTICES

▯ Never use steam cleaning products to clean your

dishwasher. The manufacturer will not be liable for the

possible damages or consequences.

▯ To avoid possible dishwasher damage, do not use

harsh chemicals, bleach-based wipes, abrasive

cleaners, scouring pads (metal or plastic), or abrasive

cloths/paper towels to clean your dishwashers exterior

door panel. Your dishwasher's exterior door panel can

be damaged by doing so.

▯ To avoid dishwasher damage, do not load the

dishwasher with paper products, plastic bags, packing

materials or anything other than normal, dishwasher

safe dishware and kitchenware.

▯ Protect your dishwasher from the elements. Protect

against freezing to avoid possible damage to the fill

valve. Damage caused by freezing is not covered by

the warranty.

8

Getting Started

Appliance overview

6WDUW







5HVHWVHF



6HWXSVHF







































9

The numbers stated below refer to the overview images

on the previous page of this manual.

Operating panel

Note: Some of the wash cycles and options will vary by

model.

Dishwasher interior components

Display indicators

--------

(

On/Off button

0

Wash cycles**

8

Rinse aid refill indicator

@

Salt refill indicator

H

Digital display

P

Selection buttons

X

Delay start button

`

Remote start buttton

h

Wash cycle options**

)"

START button

1"

Upper rack

1*

Silverware basket

12

Upper spray arm

1:

Detergent tab tray

1B

Vent hole

1J

Lower spray arm

1R

Dispenser for special salt

1Z

Filters

1b

Lower rack

1j

Rinse aid dispenser

9"

Detergent dispenser

9*

Lock for detergent dispenser

92

Rating plate

‹:‹‹

Cycle time remaining

%

Lights up when rinse aid is low

$

Lights up when salt is low

|

Lights up when wifi is connected

10

Menu Overview

The dishwasher has been preset with certain settings for

your convenience. You can change these factory

settings.

Change the setting as follows:

1.

Open the door.

2.

Press the ON/OFF button (.

3.

Press and hold the ‹button for 3 seconds until

•:‹... is shown on the display window H

4.

Press the ‹button to access the individual

settings.

5.

Adjust the setting using the + and - buttons. P.

6.

Press and hold the ‹button for 3 seconds.

The chosen setting has now been stored.

Note: If you want to change several settings, first make

all your changes one after the other. Then press the

‹button for 3 seconds. All the settings will then be

stored in the dishwasher.

--------

* optional feature which may or may not be included with your dishwasher.

Setting Factory set-

ting

Description

• Water hardness

•:‹‹ - •:‹ˆ

•

:‹‹

Setting the water hardness. When using Multitabs, select the lowest setting.

§ Rinse aid

§:‹‹ - §:‹‡

§

:‹†

Amount of rinse aid affects drying.

†“ Sensor setting

†“:‹‹ -†“:‹ƒ

†“

:‹‹

Adjustment of the soil detection for optimum cleaning.

š Intensive drying

š:‹‹ - š:‹‚

š

:‹‹ / Off

Improved drying for glasses and plasticware.

˜ Auto power off

˜:‹‹ - ˜:‹ƒ

˜

:‹‹

Dishwasher automatically switches off at the end of each cycle.

‚ Info light *

‚:‹‹ - ‚:‹‚

‚

:‹‚ / On

Light is projected to signal an active wash cycle.

“ Emotion Light

“:‹‹ - “:‹‚

“:‹‚

Interior lights are on.

à Time light *

à:‹‹ - à:‹‚

à

:‹‚

Time light is on.

à˜ Last program

used

à˜:‹‹ - à˜:‹‚

à˜

:‹‚

Defaults to last program used.

à– Signal volume

à–:‹‹ - à–:‹„

à–

:‹ƒ

Volume of the signal at the end of a program.

›– Button volume

›–:‹‹ - ›–:‹„

›–

:‹ƒ

Volume of the button sound.

™ Double push

™:‹‹ - ™:‹‚

™

:‹‹

Double push to open - when active, requires two pushes to open door.

’Ÿ Wifi off/on

’Ÿ:‹‹ - ’Ÿ:‹‚

’Ÿ

:‹‹

Wifi connection is off.

‘’ Auto Connect

WPS: Auto pairing.

à‘ Manual Connect

SAP: Manual connection.

‘˜:˜ App Pair

Pair appliance to app.

§“ Factory Reset

“Yes”

11

Home Connect™

This dishwasher is Wi-Fi capable and can be remotely

controlled via a mobile device.

If your dishwasher does not connect to the home

network, you can also operate the dishwasher manually

by pressing the buttons.

Refer to appliance overview for the location of the

buttons. ~ "Appliance overview" on page 8

Wi-Fi |

You can activate wireless network connection with

’Ÿ:‹‚ or deactivate it with ’Ÿ:‹‹.

Activate Wi-Fi:

1.

Press the on ON/OFF button (.

2.

Press and hold the button ‹ for 3 seconds.

In the display window H you will see •:‹... and ‘ .

3.

Press the button ‹ repeatedly until ’Ÿ:‹‹

appears in the display window

H.

4.

Use the setting button + P to activate Wi-Fi ’Ÿ:‹‚.

5.

Press and hold the button ‹ for 3 seconds.

The chosen setting has now been stored in your

dishwasher.

Note: Remote control of the dishwasher requires a

stable wireless network connection.

Network login

To connect the dishwasher to your home network, you

can choose between automatic ‘’ and manual network

login †‘. To do this, check to see if there is a WPS

function on your router.

Automatic network login ‘’: Connect to the home

network using the WPS function of your router. During

connection press the WPS button on the router.

Manual network login †‘: Connect your mobile device

to the network (SSID):__________, password (key):

__________. The network settings are then manually

entered using the Home Connect App to connect to your

home network.

Connect dishwasher to home network and app:

1.

Switch on ON/OFF switch (.

2.

Press and hold the button ‹ for 3 seconds.

In the display window H you will see •:‹... and ‘ .

3.

Press the button ‹ repeatedly until H ‘’ or

†‘ appears in the display window.

4.

Start connection with the setting button + P.

In the display window H you will see ˜‘.

Following successful connection to your home network

™:©Ÿ appears briefly in the display window H.

The dishwasher then automatically starts connection to

the app. During connection ‘˜:˜ appears in the display

window H.Following successful connection to the app

™:©Ÿ appears in the display window H.

Observe the Home Connect documents supplied.

Note: The menu items

‘’ and †‘ are not available until

Wi-Fi has been activated.

Connect to the app

The setting ‘˜:˜ establishes the link between the

dishwasher, app and your user account.

Note: This step should only be carried out if the

dishwasher has not yet automatically connected to the

app.

Connect dishwasher to app:

1.

Switch on ON/OFF switch (.

2.

Press and hold the button ‹ for 3 seconds.

In the display window H you will see •:‹... and ‘ .

3.

Press the button ‹ repeatedly until ‘˜:˜

appears in the display window

H.

4.

Start connection with the setting button + P.

If connection is successful, ™:©Ÿ appears in the display

window H.

Observe the Home Connect documents supplied.

Note: The menu item ‘˜: ˜ is not available until there is

a connection to the home network.

About data protection:

When your Home Connect dishwasher is connected for

the first time to a WLAN network which is connected to

the Internet, your Home Connect dishwasher transmits

the following categories of data to the Home Connect

server (initial registration):

▯ Unique appliance identification (consisting of

appliance codes as well as the MAC address of the

installed Wi-Fi communication module).

▯ Security certificate of the Wi-Fi communication module

(to ensure a secure IT connection).

▯ The current software and hardware version of your

dishwasher.

▯ Status of any previous resetting to factory settings.

This initial registration prepares the Home Connect

functions for use and is activated the first time you use

these Home Connect functions. Please note that the

Home Connect functions can be used only in conjunction

with the Home Connect App. Information on data

protection can be accessed in the Home Connect App.

12

Remote start button

If the dishwasher is connected to the home network, you

can activate the dishwasher's remote control.To do so,

press the remote start button

`.

If the dishwasher has not yet logged into Home Connect,

perform automatic network login ‘’ by pressing the

remote start button

`.

Observe the Home Connect documents supplied.

Notes

▯ To remotely control the dishwasher, the remote start

button

` must be activated.

▯ The remote start button ` goes out when the login

process is complete.

▯ Opening the door deactivates remote control.

▯ If the connection to the router fails, | flashes on the

display.

Wi-Fi without a connection to the Home

Connect server

ƒ

Wi-Fi without a connecti on to the Home Connect server

You can use the Home Connect App to disconnect from

the Home Connect server.

The appliance is then locally connected to your mobile

device without any connection to the Home Connect

server.

Note: If you did not deactivate the connection to the

Home Connect server, check your Internet connection.

Remote diagnostics

Customer Service can use remote diagnostics to access

your appliance if you contact them. In the display window

H you will see ’†. Confirm Customer Service access

using the setting button +

P.

Note: You can switch off remote diagnostics using the

ON/OFF switch ( or deactivate Customer Service

access in the Home Connect app.

13

Water softening system / special salt *

To ensure good rinsing results, the dishwasher requires

soft water, i.e. water which is low in lime, otherwise

limescale will be deposited on the utensils and interior

container. Tap water above 7° dH (1.2 mmol/l) must be

softened. The water is softened with special salt

(regeneration salt) in the water softening system

of the dishwasher. The setting and therefore the required

amount of salt depends on the degree of hardness of

your tap water (see following water hardness table).

* optional feature which may or may not be included with

your dishwasher.

Adjusting the water softener settings

Adjusting the water softening system

The amount of salt dispensed can be set from •:‹‹ to

•:‹ˆ. Salt is not required at the set value •:‹‹.

Set the softening system as follows:

1.

Ask your local water utility company for the water

hardness value of the tap water.

2.

Required setting can be found in the water hardness

table.

3.

Open the door.

4.

Press the ON/OFF button (.

5.

Press the Setup button for 3 seconds until •:‹‹ is

shown on the display window H.

6.

Make the selection with setting buttons + - P.

7.

Press and hold the Setup button for 3 seconds.

The chosen setting has now been stored.

Using special salt

As soon as the low salt indicator @ lights up on the

digital display, salt should be topped off. Refilling the salt

dispenser should be done before switching on the

appliance. This ensures that extra salt water is washed

out and will not corrode the rinsing tank.

NOTICE: Detergent will destroy the water softening

system! Never pour detergent into the salt dispenser.

Top off the salt as follows:

1.

Undo the screw plug on the dispenser 1R.

2.

Fill the dispenser with water (required only when

switching on the appliance for the first time).

3.

Add salt as illustrated (do not use table salt or

tablets).

The water is displaced and runs out.

For more information about buying dishwasher salt,

please contact Customer Service 1-800-944-2904.

Using the test strip included with your

dishwasher

(Purchased test strips may have a differ-

ent scale)

Water soft-

ener setting

Add salt to salt

dispenser

Water hardness

°E value mmol/l

•:‹‹

No 0-8 0-1.1

•:‹‚

Yes 9-10 1.2-1.4

•:‹ƒ

Yes 11-12 1.5-1.8

•:‹„

Yes 13-15 1.9-2.1

•:‹…

Yes 16-20 2.2-2.9

•:‹†

Yes 21-26 3.0-3.7

•:‹‡

Yes 27-38 3.8-5.4

•:‹ˆ

Yes 39-62 5.5-8.9



14

Using detergents with salt component

Detergent with a salt component

If combined detergents with a salt component are used,

special salt can usually be omitted up to a water

hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l). If

the water hardness is over 21° dH, salt must be used.

Switching off low salt indicator / water

softening system

Switching off water softening system

If the use of combined detergents with a salt component

impairs the low salt indicator on the digital display

H,

the low salt indicator can be switched off.

Proceed as described under “Setting water softening

system” and set the value to

•:‹‹. The water softening

system and salt refill indicator are now switched off.

15

Rinse Aid

As soon as the low rinse aid indicator 8 lights up on

the control panel, rinse aid should be topped off.

The rinse aid is required for stain-free utensils and clear

glasses. Use only rinse aid which the manufacturer

designates as safe to use in domestic dishwashers.

Combined detergents with rinse aid component may be

used with soft to moderately hard water only (0-2 bands

on test strip or up to an °E value of 20). For moderately

hard to hard water (3 to 4 bands on test strip or °E value

of 21 or higher), rinse aid must be used.

Adding rinse aid

NOTICE: To avoid oversudsing or clogging, do not

overfill the rinse aid dispenser

1j. Wipe up any spills

with a damp cloth.

1.

Open the rinse aid dispenser 1j by pressing on the

latch of the lid and pulling it open.

2.

Add liquid rinse aid to the dispenser 1j until it is full.

Do not overfill. Avoid spilling into air vent hole.

3.

Close the lid. Lid must be fully closed until it clicks in

order to seal.

4.

Wipe up any excess rinse aid that may have puddled

when the dispenser reservoir is full.

This prevents excessive frothing during the next wash

cycle. The indicator light will go out a few moments

after the dishwasher door is shut.

Tip: For easier pouring, remove lid from the rinse aid

bottle.

NOTICE: Do not fill the rinse aid dispenser

1j with

detergent. Doing so will damage the dishwasher.

Setting the amount of rinse aid used

The amount of rinse aid to be dispensed can be set from

§:‹‹ to §:‹‡. Set the amount of rinse aid to be

dispensed to

§:‹† to obtain a very good drying result.

Do not change the amount of rinse aid unless there are

streaks or water stains on the utensils. Set a lower level

to avoid streaks. Set a higher level to avoid water stains.

Set the amount of rinse aid as follows:

1.

Open the door.

2.

Press on ON/OFF button (.

3.

Press the Setup button for 3 seconds until •:‹‹ is

shown on the display window H.

4.

Keep pressing the Setup button until the rinse aid

setting, §:‹† is displayed.

5.

Change the setting with the setting buttons + - P.

6.

Press and hold the Setup button for 3 seconds.

The chosen setting has now been stored.

Note: Do not change the amount of rinse aid unless

there are streaks (select lower setting) or water stains

(select higher setting) visible on the utensils.

Turning off rinse aid indicator

Proceed as described in the section “Setting the amount

of rinse aid used” and set value to §:‹‹. The rinse aid

indicator is now turned off.

NOTICE: Using no rinse aid or setting the dispenser to

§:‹‹ may result in longer cycle times consuming more

energy and water. The higher temperatures and longer

cycle times can damage fine china or glassware.





PD[

WFOU

BJS

16

Loading the Dishwasher

Dishware material

Note: Before using your dishwasher for the first time,

check the information in this section. Some items are not

dishwasher-safe and should be hand washed; others

require special loading.

Loading the racks

For best dishwashing results, observe the following when

loading the dishwasher:

▯ Do not pre-wash items with loosely attached food soil.

▯ Remove all food particles, bones, toothpicks and

excessive grease.

▯ Pre-treat items having burned-on, baked-on or starchy

soils.

▯ Load dishes in the dishwasher racks so the insides of

bowls, pots and pans are facing the spray arms.

▯ Avoid nesting and contact points between dishes.

▯ Separate items of dissimilar metals. Use care to not

block movement of the spray arms.

▯ Only wash household dishware and kitchenware rated

as dishwasher-safe.

Refer to the Dishware Materials section for more

information about dishware suitability.

NOTICE: To avoid dishwasher damage, do not load the

dishwasher with paper products, plastic bags, packing

materials or anything other than normal, dishwasher safe

dishware and kitchenware.

Loading the upper rack

Ensure items do not protrude through the bottom of the

racks and block the spray arms.

Note: When pushing the upper rack

1" into the

dishwasher, push it until it stops against the back of the

tub so the upper rack spray arm 12 connects to the

water supply at the back of the tub. Do not push racks in

using the door.

Loading the lower rack

Place large items in the lower rack 1b. Load pots, pans

and bowls upside down. Do not block the vent hole 1B

with tall baking sheets. Load these items on the right side

of the dishwasher.

Recommended Precaution

Aluminum Colored anodized aluminum may

fade over time. Minerals in your

water may cause the aluminum to

darken or spot. This can usually

be removed with a soap-filled

steel wool pad.

China, Crystal,

Stoneware

Some hand-painted utensils may

discolor, fade or spot. Hand wash

these utensils. Position fragile

glassware so that it will not topple

over or come in contact with

other utensils during the wash

cycle.

Glass Make sure to use dishwasher-

safe glass. Milk glass may dis-

color or become yellow.

Non-stick Coatings Apply a light coating of vegetable

oil to non-stick surfaces after dry-

ing.

Plastics Make sure the plasticware is dish-

washer-safe.

Stainless Steel,

Sterling Silver and

Silver Plates

Load these so they do not come

in contact with other metals, stain-

less steel dishwasher tank walls

or the inner door.

Not

Recommended

Reason

Acrylic Crazing or small cracks through-

out the acrylic, may occur.

Adhesive-

Joined Pieces

Adhesives that join materials

such as plastic, wood, bone,

steel, copper, tin, etc. may

loosen.

Bone-Handled

Utensils

Handles may separate.

Iron Iron will rust. Hand wash and dry

immediately.

Non-Dishware

Items

Your dishwasher is intended for

use in cleaning ONLY standard

household dishware and kitchen-

ware.

Pewter, Brass,

Bronze

These items will tarnish. Hand

wash and dry immediately.

17

Loading patterns

Loading the lower rack

Adjusting the glassware supports

Slide the supports along the curve and up to the desired

level. Check to make sure both sides of the support are

in the same level.

Choosing the right level for supports

Position the supports at the level which provides the

most stability to the glasses while titlted at a slight angle.

For stemware, be sure the stem rests in a groove.

Load front row first

For best results, always load the front row first. When

unloading, start with the back row.

Loading with all stemware

Loading with mixed glassware

18

Suggested loading pattern for upper rack

Unloading the dishwasher

9 CAUTION

Dishes can be very hot immediately after cycle

ends. Open the door slightly and allow dishes to

cool for a few minutes before unloading.

Note: Dishes are more likely to chip when unloading

before cooling.

When unloading the dishwasher, to prevent water from

dripping onto dry dishes, unload the lower rack 1b first.

Next, unload the silverware basket 1* followed by the

upper rack 1", and then the third rack (if equipped).

RackMatic

®

The height of the upper rack 1" can be adjusted in

3 steps to create more space for larger items in the

lower rack.

1.

Pull the upper rack out of the dishwasher until it stops.

2.

To lower the rack, push the RackMatic® lever inward.

3.

To raise the rack, hold the basket on the sides of the

upper rack and lift it up.

Note: Check spray arm for clearance after adjustment.

19

Removing/Installing upper rack with

Rackmatic

®

Removing upper rack 1"

1.

Pull out upper rack all the way (1).

2.

Lift front rollers over the stopper hook of the rail (2).

3.

Pull out upper rack forwards and upwards so that the

upper and lower rollers of the rack slide over the

stopper hooks of both rails (3).

Installing upper rack 1"

1.

Pull out upper rack rails all the way (1).

2.

Insert upper rack at an angle. Make sure that the

stopper hooks of both rails slide in between the upper

and lower rollers on the rear side of the rack (2).

3.

Slide upper rack in and lift the upper rollers over the

front stopper hooks of both rails (3).

4.

Push in upper rack (4).















20

Detergent

Use only detergent specifically designed for

dishwashers. For best results, use fresh powdered

dishwashing detergent or detergent tabs.

NOTICE:

To avoid damage to dishwasher or dishware:

▯ Do not use hand dishwashing products in your

dishwasher.

▯ Do not use too much detergent if your water is soft.

Using too much detergent with soft water may cause

etching in glassware and fine china.

▯ To best protect glassware, use a wash cycle with low

temperatures or a specific glass-care cycle

(depending on the model) and use a detergent that

includes etch protection.

This dishwasher uses less water than most, therefore,

less detergent is required. With soft water, 1 tablespoon

(15 ml) of detergent will clean most loads. The detergent

dispenser cup has lines that measure detergent to

1 tablespoon (15 ml) and 1.75 tablespoons (25 ml).

3 tablespoons (45 ml) of detergent will completely fill the

detergent dispenser.

Note: If you do not know the hardness of your water

supply, use 15 ml of detergent. Increase the amount if

necessary to the least amount required to get your

kitchenware clean.

Use the measuring lines in the detergent dispenser cup

as a guide to measure the amount of detergent

recommended in the following table.

Adding detergent

1.

If the detergent dispenser 9" is still closed, push the

button

9* to open it.

Note: Make sure the detergent dispenser is dry and

clear of detergent residue.

2.

When using detergent tabs, lay them such that they do

not come in contact with the cover, insert a detergent

tab flat, not on its side.

Note: Do not place detergent tabs or utensils in the

detergent tab tray 1:. Place tabs or other detergent

forms directly in the detergent dispenser 9".

Wash Cycle Hard Water/

Heavy Soil

Medium

Water/

Medium

Soil

Soft Water/

Little Soil

Auto 3 tbsp

(45 ml)

1.75-3 tbsp

(25-45 ml)

1-1.75 tbsp

(15 - 25 ml)

Normal 1.75-3 tbsp

(25 - 45 ml)

1.75 tbsp

(25 ml)

1-1.75 tbsp

(15 - 25 ml)

Glass 1.5-2.75

tbsp

(22 - 40 ml)

1.35-1.75

tbsp

(20 - 25 ml)

1-1.5 tbsp

(15 - 22 ml)

Star Speed 1.75 tbsp

(25 ml)

1-1.75 tbsp

(15 - 25 ml)

1 tbsp

(15 ml)

1 Hour 1.75 tbsp

(25 ml)

1-1.75 tbsp

(15 - 25 ml)

1 tbsp

(15 ml)

Quick 1.75 tbsp

(25 ml)

1-1.75 tbsp

(15 - 25 ml)

1 tbsp

(15 ml)

Rinse none none none

La page charge ...

Thermador DWHD771WFM Mode d'emploi

Thermador DWHD771WFM Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents