GE Artistry Series GBS20ESHSS Le manuel du propriétaire

GEAppliances.com

Refrigerators

Bottom Freezer

200D9366P004 49-60539-4 05-17 GEA

Safety Instructions ............2, 3

Operating Instructions

Automatic Icemaker ................10

Care and Cleaning .............11, 12

Controls ............................4

Crispers and Pans ...................7

Freezer ...........................8, 9

Replacing the Light Bulbs ...........13

Shelves and Bins ....................6

Water Filter .........................5

Installation Instructions

Installing the Refrigerator .......15–19

Installing the Water Line ........28–30

Preparing to Install

the Refrigerator ....................14

Removing and Replacing

the Doors (Double Door

Refrigerator Models only) .......25–27

Removing and Replacing the

Freezer Drawer ................20, 21

Reversing the Door Swing

(Single Door Refrigerator

Models only) ...................22–25

Troubleshooting Tips ......32–34

Normal Operating Sounds ..........31

Consumer Support

Consumer Support ........Back Cover

Performance Data Sheet ...........36

Warranty ..........................37

Réfrigérateurs

Congélateur inférieur

Refrigeradores

Congelador inferior

Write the model and serial

numbers here:

Model # ____________________

Serial # _____________________

Find these numbers on a label

on the right side, near the top of the

refrigerator compartment.

Models 20, 21, 22 and 23

Manuel d’utilisation

et d’installation

Owner’s Manual and

Installation Instructions

Manual del

propietario e

instalación

La section française commence à la page 43

La sección en español empieza en la página 81

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

2

GE Appliances website

For more information on your refrigerator’s operation, visit www.GEAppliances.com or

call 800.GECARES (800.432.2737). In Canada visit GEAppliances.ca or call 800.561.3344.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety

messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words are defined as:

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

REFRIGERATOR SAFETY INFORMATION

SAFETY

WARNING

DANGER

CAUTION

WARNING

Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can

result in fire, explosion, or death.

INSTALLATION

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, explosion, electric shock, or injury when using your

refrigerator follow these basic safety precautions:

WARNING

 Do not clean glass shelves or covers with warm water when

they are cold. Glass shelves and covers may break if exposed

to sudden temperature changes or impact, such as bumping

or dropping. Tempered glass is designed to shatter into many

small pieces if it breaks.

 Keep fingers out of the “pinch point” areas; clearances between

the doors and between the doors and cabinet are necessarily

small. Be careful closing doors when children are in the area.

 Do not touch the cold surfaces in the freezer compartment

when hands are damp or wet, skin may stick to these extremely

cold surfaces.

 Do not refreeze frozen foods which have thawed completely.

 In refrigerators with automatic icemakers, avoid contact with

the moving parts of the ejector mechanism, or with the heating

element that releases the cubes. Do not place fingers or hands

on the automatic ice making mechanism while the refrigerator

is plugged in.

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of injury when using your refrigerator, follow these basic

safety precautions.

 This refrigerator must be properly installed and located in

accordance with the Installation Instructions before it is used.

 Unplug the refrigerator before making repairs, replacing a light

bulb, or cleaning.

Note: Power to the refrigerator cannot be disconnected by any

setting on the control panel.

Note: Repairs must be performed by a qualified service

professional.

 Replace all parts and panels before operating.

 Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.



Because of potential safety hazards under certain conditions,

we strongly recommend against the use of an extension cord.

However, if you must use an extension cord, it is absolutely

necessary that it be a UL-listed (in the United States) or a CSA

certified (in Canada), 3-wire grounding type appliance extension

cord having a grounding type plug and outlet and that the electrical

rating of the cord be 15 amperes (minimum) and 120 volts.

 To prevent suffocation and entrapment hazards to children,

remove the fresh food and freezer doors from any refrigerator

before disposing of it or discontinuing its use.

 Do not allow children to climb, stand or hang on the door

handles or the shelves in the refrigerator. They could seriously

injure themselves.

CAUTION

GEAppliances.com

USE OF ADAPTER PLUGS

Adapter plugs are not permitted in Canada.

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall outlet to minimize the

possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly

grounded.

Where a standard 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to have

it replaced with a properly grounded 3-prong wall

outlet. Do not use an adapter.

The refrigerator should always be plugged into its own

individual electrical outlet which has a voltage rating

that matches the rating plate.

A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded

electrical supply is required. This provides the best

performance and also prevents overloading house

wiring circuits which could cause a fire hazard from

overheated wires.

Never unplug your refrigerator by pulling on the power

cord. Always grip plug firmly and pull straight out from

the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the wall, be

careful not to roll over or damage the power cord.

CONNECTING ELECTRICITY

WARNING

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet

Do not remove the ground prong

Do not use an adapter

Failure to follow these instructions can result in death, fire, or electrical shock.

SAFETY (CONT.)

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

WARNING

Suffocation and child entrapment hazard.

Remove fresh-food and freezer doors from the refrigerator, prior to disposal. Failure to do so can result

in child entrapment which can lead to death or brain damage.

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Refrigerator or

Freezer:

 Take off the fresh food and freezer doors.

 Leave the shelves in place so that children may

not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an old

refrigeration product, check with the company

handling the disposal about what to do.

PROPER DISPOSAL OF YOUR OLD REFRIGERATOR

IMPORTANT:

3

4

About the controls with temperature settings.

Initially, set the refrigerator control at 5 and the freezer control at 5. Allow 24 hours for

the temperature to stabilize. Several adjustments may be required. Adjust the controls

one increment at a time, and allow 24 hours after each adjustment for the refrigerator

to reach the temperature you have set.

Setting either or both controls to 0 for digital and 0 for the refrigerator control knob

stops cooling in both the refrigerator and freezer compartments, but does not shut

off electrical power to the refrigerator.

NOTE: The refrigerator is shipped with protective film covering the digital temperature

controls. If this film was not removed during installation, remove it now.

(on some models)

5

Water Filter Cartridge

The water filter cartridge is located in the

back upper right corner of the refrigerator

compartment.

When to Replace the Filter

The filter cartridge should be replaced

when the flow of water to the icemaker

decreases, or every six months.

Installing the Filter Cartridge

If you are replacing the cartridge, first

remove the old one. Open the cartridge

cover by pressing in on the tab at the front

and pulling down.

Remove the cartridge by slowly rotating it

counterclockwise. A small amount of water

may drip down.

CAUTION

If air has been trapped in the

system, the filter cartridge may be ejected as it is

removed. Use caution when removing.

Remove the protective foil from the end of

the cartridge.

Lining up the arrow on the cartridge

and the cartridge holder, slowly rotate the

cartridge clockwise until it stops. When the

cartridge is properly installed, you will feel it

“click” as it locks into place. The grip on the

end of the cartridge should be positioned

vertically.

Do not overtighten.

Close the cartridge cover.

Filter Bypass Plug

You must use the filter bypass plug when a

replacement filter cartridge is not available. The

icemaker will not operate without the filter or

filter bypass plug.

Replacement Filters:

To order additional filter cartridges

in the United States, visit our Website,

GEAppliances.com, or call GE Appliances

Parts and Accessories, 800.626.2002.

Filter Model GSWF

Customers in Canada should consult

the yellow pages for the nearest Mabe Service

Center.

About the water filter. (on some models) GEAppliances.com

6

Rearranging the Shelves

To remove:

Remove all items from the shelf.

Tilt the shelf up at the front.

Lift the shelf up at the back and bring the

shelf out.

To replace:

While tilting the shelf up, insert the top hook

at the back of the shelf in a slot

on the track.

Lower the front of the shelf until the bottom

of the shelf locks into place.

About the shelves and bins.

Not all features are on all models.

Some models have wire shelves

that can be adjusted in the same

manner.

Shelves in the refrigerator compartment are adjustable.

Refrigerator Compartment

Non-Adjustable Shelves on the Door (on some models)

To remove: Lift the shelf straight up; then

pull out.

To replace: Engage the shelf in the molded

supports on the door and push down.

It will lock in place.

7

About the crispers and pans. GEAppliances.com

Not all features are on all models.

Adjustable Humidity Crisper (on some models)

Slide the control all the way to the

HIGH setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the LOW setting

to provide lower humidity levels recommended

for most fruits.

Fruit and Vegetable Crisper

Excess water that may accumulate in the

bottom of the drawers or under the drawers

should be wiped dry.

Snack Pan (on some models)

This pan can be moved to the most useful

location for your family’s needs.

To remove, slide the pan out to the stop

position, lift the pan up and past the stop

position and lift it out.

8

Freezer Shelves and Baskets

A shelf above the ice storage bin

A half-width basket

A deep full-width basket

NOTE: Do not fill baskets higher than the rim of

the basket. This may cause baskets to stick or

jam when opening or closing.

Basket Removal

To remove the deep full-width basket on

freezer drawer models:

Open the freezer drawer until it stops.

The freezer basket rests on the inside tabs

on the drawer slides.

Lift the basket so that it is out of all 6 slide

bracket tabs.

Tilt the basket and lift out of the drawer.

When replacing the deep full-width basket:

Tilt the basket back and lower it down into

the drawer. Rotate the basket to a horizontal

position and press it down into the 6 alignment

tabs.

NOTE: Always be sure that the basket is seated

in all 6 slide bracket tabs before sliding back

into the freezer. The basket can be turned in

either direction front to back and installed into

the freezer.

To remove the half-width basket:

Pull the basket out to the stop location.

Lift the basket up at the front to release it

from the stop hooks on each side.

Lift the basket out to remove it from the

sides.

When replacing the basket, make sure that the

basket goes under the stop hooks on each side.

NOTE: Always be sure to fully close this basket.

About the freezer drawer. (on some models)

Not all features are on all models.

Appearance and features may vary

Appearance may vary

9

Freezer Shelf and Basket

A full-width fixed wire shelf

A full-width sliding wire basket

NOTE: Do not fill basket higher than the rim of

the basket. This may cause basket to stick or

jam when opening or closing.

Basket Removal

To remove the full-width sliding wire basket

on door models:

Open the basket out to its full extension.

Lift up the front of the basket and pull

straight out to remove.

When replacing the full-width sliding

wire basket:

Insert the wire basket into the lower liner’s rails

and push back into place.

NOTE: The full-width wire shelf is not intended

to slide.

To remove for cleaning:

Hold the shelf at the front and pull it firmly

forward.

When replacing the full-width sliding wire

shelf:

Insert the wire shelf into the upper liner’s rails

and push back into place.

About the freezer compartment. (on some models) GEAppliances.com

Not all features are on all models.

Fixed Shelf Removal

To remove: Lift the shelf straight up;

then pull out.

To replace: Engage the shelf in the molded

supports on the door and push down. It will lock

in place.

Non-Adjustable Shelf on Freezer Door

To remove

To replace

10

Automatic Icemaker

7KHLFHPDNHUZLOOSURGXFHVHYHQFXEHVSHUF\FOH³

approximately 100–130 cubes in a 24-hour period,

depending on freezer compartment temperature,

room temperature, number of door openings and

other use conditions.

See below for how to access ice and reach the

power switch.

If the refrigerator is operated before the water

connection is made to the icemaker, set the power

switch in the O (off) position.

When the refrigerator has been connected to

the water supply, set the power switch to the l (on)

position. The icemaker power light will turn green

when the freezer light switch is pressed in or when

the freezer door is closed.

The icemaker will fill with water when it cools to 15°F

(–10°C). A newly installed refrigerator may take 12 to

24 hours to begin making ice cubes.

You will hear a buzzing sound each time the

icemaker fills with water.

Throw away the first few batches of ice to allow the

water line to clear.

Be sure nothing interferes with the sweep of the

feeler arm.

When the bin fills to the level of the feeler arm, the

icemaker will stop producing ice. It is normal for

several cubes to be joined together.

If ice is not used frequently, old ice cubes will

become cloudy, taste stale and shrink.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

NOTE: Set the power switch to the O (off) position if

the water supply is shut off.

CAUTION

Avoid contact with the

moving parts of the ejector mechanism, or

with the heating element (located on the

bottom of the ice maker) that releases the

cubes. Do not place fingers or hands on the

automatic ice making mechanism while the

refrigerator is plugged in.

About the automatic icemaker. (on some models)

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Feeler Arm

Icemaker

Green

Power

Light

Power

Switch

Accessing Ice and Reaching the

Power Switch

To reach the icemaker power switch, pull the shelf

above the ice bin straight out. Always be sure to

replace the shelf.

To access ice, simply pull the bin forward.

To access ice.

Shelf

Ice Bin

To reach the power switch.

Shelf

Ice Bin

Icemaker Accessory Kit

If your refrigerator did not come already equipped

with an automatic icemaker, an icemaker accessory

kit is available at extra cost.

Check the back of the refrigerator for the specific

icemaker kit needed for your model.

Care and cleaning of the refrigerator. GEAppliances.com

Cleaning the Outside

The door handles and trim. Clean with a cloth

dampened with soapy water. Dry with a soft

cloth. Do not use wax on the door handles and

trim.

Keep the outside clean. Wipe with a clean

cloth lightly dampened with kitchen appliance

wax or mild liquid dish detergent. Dry and

polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled

dish cloth or wet towel. These may leave a

residue that can erode the paint. Do not use

scouring pads, powdered cleaners, bleach

or cleaners containing bleach because these

products can scratch and weaken the paint

finish.

The stainless steel panels and door handles.

The stainless steel doors and door handles

(on some models) can be cleaned with a

commercially available stainless steel cleaner.

Cleaners with oxalic acid such as Bar Keepers

Friend Soft Cleanser™ will remove rust, tarnish

and small blemishes. Use only a liquid cleanser

free of grit and rub in the direction of the brush

lines with a damp soft sponge.

Do not use appliance wax or polish on the

stainless steel.

Cleaning the Inside

To help prevent odors, leave an open box

of baking soda in the refrigerator and freezer

compartments.

Unplug the refrigerator before cleaning.

If this is not practical, wring excess moisture

out of sponge or cloth when cleaning around

switches, lights or controls.

Use an appliance wax polish on the inside

surface between the doors.

8VHZDUPZDWHUDQGEDNLQJVRGDVROXWLRQ³

about a tablespoon (15 ml) of baking soda to

a quart (1 liter) of water. This both cleans and

neutralizes odors. Rinse and wipe dry.

After cleaning the door gaskets, apply a thin

layer of petroleum jelly to the door gaskets

at the hinge side. This helps keep the gaskets

from sticking and bending out of shape.

CAUTION

Do not clean glass shelves

or covers with warm water when they are

cold. Glass shelves and covers may break

if exposed to sudden temperature changes

or impact such as bumping or dropping.

Tempered glass is designed to shatter into

many small pieces if it breaks.

Do not wash any plastic refrigerator parts in

the dishwasher.

11

12

Care and cleaning of the refrigerator.

For long vacations or absences, remove food

and unplug the refrigerator. Clean the interior

with a baking soda solution of one tablespoon

(15 ml) of baking soda to one quart (1 liter) of

water. Leave the doors open.

Set the icemaker power switch to the O (off)

position and shut off the water supply to the

refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water supply

system (on some models) to prevent serious

property damage due to flooding.

Preparing for Vacation

Preparing to Move

Secure all loose items such as base grille,

shelves and drawers by taping them securely

in place to prevent damage.

When using a hand truck to move the

refrigerator, do not rest the front or back of the

refrigerator against the hand truck. This could

damage the refrigerator. Handle only from the

sides of the refrigerator.

Be sure the refrigerator stays in an upright

position during moving.

Behind the Refrigerator

Be careful when moving the refrigerator away

from the wall. All types of floor coverings can

be damaged, particularly cushioned coverings

and those with embossed surfaces.

Raise the leveling legs located at the bottom

front of the refrigerator.

Pull the refrigerator straight out and return it

to position by pushing it straight in. Moving the

refrigerator in a side direction may result in

damage to the floor covering or refrigerator.

Lower the leveling legs until they touch the

floor.

When pushing the refrigerator back, make

sure you don’t roll over the power cord or

icemaker supply line (on some models).

13

Refrigerator Lights

Unplug the refrigerator.

To remove the light shield, grasp the shield

at the back and pull out to release the tabs

at the back.

Rotate the shield down and then forward to

release the tabs at the front of the shield.

After replacing with an appliance bulb

of the same or lower wattage, replace the

shield.

Plug the refrigerator back in.

NOTE: Appliance bulbs may be ordered from GE

Appliance Parts and Accessories, 800.626.2002.

Replacing the light bulbs. GEAppliances.com

Freezer Light

Appearance may vary

Unplug the refrigerator.

The bulb is located at the top of the freezer

inside a light shield. To remove the shield,

grasp the shield at the back and pull out to

release the tabs at the back.

Rotate the shield down and then forward to

release the tabs at the front of the shield.

After replacing with an appliance bulb

of the same or lower wattage, replace the

shield.

Plug the refrigerator back in.

WARNING

Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a

live wire filament. (A burned-out light bulb may break when being replaced.)

Turning the control to the OFF position does not remove power to the light circuit.

Installation

Refrigerator

Instructions

Models 20, 21, 22 and 23

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT ³ Save these instructions

for local inspector’s use.

•

IMPORTANT ³ Observe all governing

codes and ordinances.

•

Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time –

Refrigerator Installation

20 minutes

Water Line Installation

30 minutes

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

PREPARATION

MOVING THE REFRIGERATOR INDOORS

If the refrigerator will not fit through a doorway,

the refrigerator door and freezer drawer can be

removed.

• To remove the refrigerator door, see Step 1 in

the Reversing the Door Swing section.

• To remove the freezer drawer, see the Removing

the Freezer Drawer section.

WATER SUPPLY TO THE ICEMAKER AND

DISPENSER (ON SOME MODELS)

If the refrigerator has an icemaker, it will have

to be connected to a cold water line. A GE Appliances

water supply kit (containing tubing, shutoff valve, fittings

and instructions) is available at extra cost from your

dealer, by visiting our Website at GEAppliances.com (in

Canada at www.geappliances.ca) or from Parts and

Accessories, 800.626.2002 (In Canada 1.888.661.1616).

TOOLS YOU MAY NEED

Adjustable Wrench

1/4” Outer Diameter

Compression Nut

and Ferrule (sleeve)

(icemaker models only)

Phillips Head Screwdriver

14

3/8” and 5/16” Socket

Ratchet/Driver

3/32”, 1/8” and 3/16” Allen

wrenches

Pencil

1/8” Drill Bit and

Electric or Hand Drill

Tape measure

1/4” Nut Driver

Wire Cutters

Level

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature

will go below 60°F (16°C) because it will not run often

enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature

will go above 100°F (37°C) because it will not perform

properly.

• Do not install the refrigerator in a location exposed to

water (rain, etc.) or direct sunlight.

• Install it on a floor strong enough to support it fully

loaded.

CLEARANCES

For clearance for ease of installation, proper air

circulation and plumbing and electrical, please refer to

the rating plate on the top left wall of the refrigerator.

CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE

(icemaker models)

A cold water supply is required for automatic

icemaker operation. If there is not a cold water

supply, you will need to provide one. See Installing

the Water Line section.

NOTES:

• Before making the connection to the refrigerator,

be sure the refrigerator power cord is not plugged

into the wall outlet.

• If your refrigerator does not have a water filter,

we recommend installing one if your water supply

has sand or particles that could clog the screen of

the refrigerator’s water valve. Install it in the water

line near the refrigerator. If using SmartConnect

™

Refrigerator Tubing Kit, you will need an additional

tube (WX08X10002) to connect the filter. Do not cut

plastic tube to install filter.

1

REMOVE TOP CAP (on some models)

•

IMPORTANT NOTE: This refrigerator is 34-1/2” deep.

Doors and passageways leading to the installation

location must be at least 36” wide in order to leave

the doors and handles attached to the refrigerator

while transporting it into the installation location. If

passageways are less than 36”, the refrigerator doors

and handles can easily be scratched and damaged.

The top cap and doors can be removed to allow the

refrigerator to be safely moved indoors. Start with Step A.

• If it is not necessary to remove doors, skip Step A.

Leave tape and all packaging on doors until the

refrigerator is in the final location.

• SKID REMOVAL: Tilt refrigerator to each side to

remove skid.

• NOTE: Use a padded hand truck to move this

refrigerator. Place the refrigerator on the hand truck

with a side against the truck. We strongly recommend

that TWO PEOPLE move and complete this installation.

Locate and remove the two Phillips head screws on

the top of the refrigerator. Remove the two screws

on each side at the rear of the top cap. Lift off and

remove top cap.

Remove the fresh-food door(s). Refer to Steps 1 and 3

of “Reversing the Door Swing” section or Steps 1 and

2 of “Removing the Doors” section.

Remove the bottom freezer drawer or door. Refer

to “Removing Freezer Drawer” section or Step 2 of

“Reversing the Door Swing” section.

Move refrigerator to the installation location.

A

B

C

D

15

REMOVE TOP CAP (cont.)

(on some models)

REINSTALL DOORS, DRAWERS AND TOP CAP

Carefully lower the door(s) onto the center

hinge(s). Reinstall top hinge(s). NOTE: Ensure

the door is properly aligned to the case top to

avoid readjustment of the door during top cap

reinstallation.

Place cap over the top of the refrigerator. Reinstall

the original screws in the top and back of the cap.

Reinstall the bottom freezer drawer or door. Refer to

“Replacing the Freezer Drawer” section or Step 8 of

“Reversing the Door Swing” section.

E

F

G

A

Top Hinge B

CONNECTING THE REFRIGERATOR TO

THE HOUSE WATER LINE

(cont.)

If you are using copper tubing, place a

compression nut and ferrule (sleeve) onto the

end of the tubing coming from the house cold

water supply.

If you are using the SmartConnect

™

tubing, the

nuts are already assembled to the tubing.

If you are using copper tubing, insert the end

of the tubing into the refrigerator connection, at

the back of the refrigerator, as far as possible.

While holding the tubing, tighten the fitting.

If you are using SmartConnect

™

tubing,

insert the molded end of the tubing into the

refrigerator connection, at the back of the

refrigerator, and tighten the compression nut

until it is hand tight. Then tighten one additional

turn with a wrench. Overtightening may cause

leaks.

Fasten the tubing into the clamp provided to

hold it in position. You may need to pry open the

clamp.

One of the illustrations below will look like the

connection on your refrigerator.

Icemaker-Ready models

Icemaker-Installed Models

16

Installation Instructions

1

A

B

C

Tubing Clamp

1/4d

Compression

Nut

Ferrule

(sleeve)

SmartConnect

™

Tubing

Refrigerator

Connection

TURN ON THE WATER SUPPLY

(icemaker models)

Turn the water on at the shutoff valve (house

water supply) and check for any leaks.

2

PLUG IN THE REFRIGERATOR

On models with an icemaker, before plugging

in the refrigerator, make sure the icemaker

power switch is set to the O (off) position.

See the grounding information attached to the

power cord.

3

PUT THE REFRIGERATOR IN PLACE

Move the refrigerator to its final location.

4

1/4d Copper

Tubing

1/4d

Compression

Nut

Ferrule

(sleeve)

SmartConnect

™

Tubing

Refrigerator

Connection

Tubing

Clamp

LEVEL THE REFRIGERATOR

Adjustable legs at the front corners of the

refrigerator should be set so the refrigerator is

firmly positioned on the floor, and the front is

raised just enough that the door closes easily

when opened about halfway.

To adjust the leveling legs, turn the

legs clockwise to raise the refrigerator,

counterclockwise to lower it.

5

1/4d Tubing

INSTALLING THE REFRIGERATOR (cont.)

Installation Instructions

REMOVE THE FRESH FOOD

DOOR HANDLE

(For placement in the installation location

or reversal of the handles – on some

models)

Stainless steel (on

some models):

A

REMOVING

THE DOOR

HANDLE: Loosen

the set screws

with the 3/32”

Allen wrench

and remove

the handle.

NOTE: For

Double Door

models follow

the same

procedure on

the opposite

door.

Plastic handle

(on some models):

A

REMOVING THE DOOR HANDLE: Depress the

tab on the

underside of

the handle and

slide the handle

up and off of

the mounting

fasteners.

REVERSING THE

DOOR HANDLE

(on some

models):

• Remove

the handle

mounting

fasteners with a 3/16” Allen wrench and

transfer

the handle mounting fasteners to the right

side.

• Remove the logo badge.

• Remove and transfer the plug button to

the left side of the fresh food door. NOTE:

Use a flat plastic edge to prevent damaging

the door. Remove any adhesive on the door

with a mild detergent. Remove the paper

covering on the adhesive backing on the

logo badge prior to carefully attaching the

badge to the door.

6

A

B

A

B

Mounting

Fasteners

Mounting

Fasteners

Badge

(appearance may vary)

REMOVE THE FREEZER DOOR HANDLE

Stainless steel and plastic handles:

A

Loosen the set screws located on the

underside of the handle with the 1/8” Allen

wrench and remove the handle.

NOTE: If the handle mounting fasteners need

to be tightened or removed, use a 3/16” Allen

wrench.

7

A

17

ATTACH THE FREEZER DOOR HANDLE

Stainless steel and plastic handles:

A

Attach the handle firmly to the mounting

fasteners and tighten the set screws on

the bottom of the handle with a 1/8” Allen

wrench.

Installation Instructions

18

ATTACH THE FRESH FOOD

DOOR HANDLE

Stainless steel handle:

A

Attach the

handle to the

handle mounting

fasteners and

tighten the set

screws with a

3/32” Allen

wrench.

NOTE: For

Double Door

models follow

the same

procedure on the

opposite door.

Plastic handle:

A

Attach the handle to the handle mounting

fasteners by aligning the slots with the

handle mounting fasteners.

Slide it down until it is firmly locked into

position.

8

A

Mounting

Fasteners

(appearance may vary)

Mounting

fasteners

Slots on back of

handle

A

9

A

(appearance may vary)

INSTALLING THE REFRIGERATOR (cont.)

LEVEL THE REFRIGERATOR

The leveling legs have 2 purposes:

1) Leveling legs adjust so the refrigerator is

firmly positioned on the floor and does not

wobble.

2) Leveling legs serve as a stabilizing brake

to hold the refrigerator securely in position

during operation and cleaning. The leveling

legs also prevent the refrigerator from

tipping.

Remove the grille by removing the two Phillips

head screws.

Turn the leveling legs clockwise to raise

the refrigerator, counterclockwise to lower it.

CAUTION

To avoid possible personal

injury or property damage,

the leveling legs must be firmly touching

the floor.

Replace the base grille by inserting the two

Phillips head screws.

10

A

Installation Instructions

SET THE CONTROLS

Set the controls to the recommended setting.

11

REMOVE PACKAGING, START ICEMAKER

(icemaker models)

A) Remove all tape, foam and protective

packing from shelves and drawers.

B) Remove the tie downs from the freezer

baskets.

C) Place half width basket onto drawer slides.

See About the freezer section for instructions.

Set the icemaker power switch to the I (on) position.

The icemaker will not begin to operate until it

reaches its operating temperature of 15°F (–9°C) or

below. It will then begin operation automatically. It

will take 2–3 days to fill the ice bin.

NOTE: In lower water pressure conditions,

the water valve may turn on up to 3 times to

deliver enough water to the icemaker.

12

Power

switch

B

C

19

20

Installation Instructions

REMOVE THE BASE GRILLE

(if needed)

If, after removing the freezer drawer and

refrigerator door, the refrigerator will still not

fit through a doorway, the base grille can be

removed.

Remove the base grille by removing the screws.

3

A

REMOVING THE FREEZER DRAWER (on some models)

REMOVE THE BASKET

Open the freezer drawer until it stops.

The freezer basket rests on a frame inside the

freezer drawer. Lift the basket up at the back.

Lift the front up and lift the entire basket up

and out of the drawer.

1

A

B

C

The freezer drawer can be removed, if needed,

to fit through tight areas.

Read these instructions completely and carefully.

REMOVE THE DRAWER FRONT

Remove the screw on each side of the railing.

2

A

REMOVE THE DRAWER FRONT (cont.)

Lift up on both sides of the freezer drawer

handle to separate the drawer railings from

the rail assemblies.

Set the drawer front on a non-scratching

surface.

Push the rail assemblies back into locking

position.

2

B

C

D

Rail Assembly

Drawer

Assembly

A

Screw

La page charge ...

GE Artistry Series GBS20ESHSS Le manuel du propriétaire

GE Artistry Series GBS20ESHSS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents