Zanussi ZEL6640XBA Manuel utilisateur
- Catégorie
- Plaques de cuisson
- Taper
- Manuel utilisateur
Contents
Safety information 2
Safety Instructions 3
Product description 5
Daily use 7
Hints and tips 9
Care and cleaning 10
Troubleshooting 10
Installation 12
Technical information 14
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an
incorrect installation and use causes injuries and damages.
Always keep the instructions with the appliance for future
reference.
Children and vulnerable people safety
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep children and pets away from the appliance when it
operates or when it cools down. Accessible parts are hot.
• If the appliance has a child safety device, we recommend you
activate it.
• Cleaning and user maintenance shall not be made by children
without supervision.
• Children of less than 3 years should be kept away unless
continuously supervised.
General Safety
• The appliance and its accessible parts become hot during use.
Do not touch the heating elements.
• Do not operate the appliance by means of an external timer or
separate remote-control system.
2 www.zanussi.com
• Unattended cooking on a hob with fat or oil can be dangerous
and may result in fire.
• Never try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire blanket.
• Do not store items on the cooking surfaces.
• Metallic objects such as knives, forks, spoons and lids should
not be placed on the hob surface since they can get hot.
• Do not use a steam cleaner to clean the appliance.
• After use, switch off the hob element by its control and do not
rely on the pan detector.
• If the glass ceramic surface/ glass surface is cracked, switch
off the appliance to avoid the possibility of electric shock
• If the supply cord is damaged, it must be replaced by the
manufacturer, an authorized Service or similarly qualified
persons in order to avoid a hazard.
Safety Instructions
Installation
WARNING!
Only a qualified person must install
this appliance.
• Remove all the packaging.
• Do not install or use a damaged appliance.
• Obey the installation instruction supplied
with the appliance.
• Keep the minimum distance from the other
appliances and units.
• Always be careful when you move the
appliance because it is heavy. Always wear
safety gloves.
• Seal the cut surfaces with a sealant to
prevent moisture to cause swelling.
• Protect the bottom of the appliance from
steam and moisture.
• Do not install the appliance adjacent to a
door or under a window. This prevents hot
cookware to fall from the appliance when the
door or the window is opened.
• If the appliance is installed above drawers
make sure that the space, between the
bottom of the appliance and the upper
drawer, is sufficient for air circulation.
• The bottom of the appliance can get hot.
Make sure to install a non-combustile
separation panel under the appliance to
prevent access to the bottom.
• Make sure that the ventilation space of 2
mm, between the worktop and the front of
the below unit, is free. The warranty does not
cover damages caused by the lack of an
adequate ventilation space.
Electrical Connection
WARNING!
Risk of fire and electrical shock.
• All electrical connections should be made by
a qualified electrician.
• The appliance must be earthed.
• Before carrying out any operation make sure
that the appliance is disconnected from the
power supply.
• Make sure that the electrical information on
the rating plate agrees with the power
supply. If not contact an electrician.
• Make sure the appliance is installed
correctly. Loose and incorrect electricity
mains cable or plug (if applicable) can make
the terminal become too hot.
• Use the correct electricity mains cable.
• Do not let the electricity mains cable tangle.
• Make sure that a shock protection is
installed.
• Use the strain relief clamp on the cable.
www.zanussi.com 3
• Make sure the mains cable or plug (if
applicable) does not touch the hot appliance
or hot cookware, when you connect the
appliance to the near sockets
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug (if applicable) or to the mains
cable. Contact an Authorised Service Centre
or an electrician to change a damaged mains
cable.
• The shock protection of live and insulated
parts must be fastened in such a way that it
cannot be removed without tools.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
• If the mains socket is loose, do not connect
the mains plug.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
• Use only correct isolation devices: line
protecting cut-outs, fuses (screw type fuses
removed from the holder), earth leakage trips
and contactors.
• The electrical installation must have an
isolation device which lets you disconnect
the appliance from the mains at all poles.
The isolation device must have a contact
opening width of minimum 3 mm.
Use
WARNING!
Risk of injury, burns and electrical
shock.
• Remove all the packaging, labelling and
protective film (if applicable) before first use.
• Use this appliance in a household
environment.
• Do not change the specification of this
appliance.
• Make sure that the ventilation openings are
not blocked.
• Do not let the appliance stay unattended
during operation.
• Set the cooking zone to “off” after each use.
• Do not rely on the pan detector.
• Do not put cutlery or saucepan lids on the
cooking zones. They can become hot.
• Do not operate the appliance with wet hands
or when it has contact with water.
• Do not use the appliance as a work surface
or as a storage surface.
• If the surface of the appliance is cracked,
disconnect immediately the appliance from
the power supply. This to prevent an
electrical shock.
• Users with a pacemaker must keep a
distance of minimum 30 cm from the
induction cooking zones when the appliance
is in operation.
• When you place food into hot oil, it may
splash.
WARNING!
Risk of fire and explosion
• Fats and oil when heated can release
flammable vapours. Keep flames or heated
objects away from fats and oils when you
cook with them.
• The vapours that very hot oil releases can
cause spontaneous combustion.
• Used oil, that can contain food remnants,
can cause fire at a lower temperature than
oil used for the first time.
• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
WARNING!
Risk of damage to the appliance.
• Do not keep hot cookware on the control
panel.
• Do not let cookware to boil dry.
• Be careful not to let objects or cookware fall
on the appliance. The surface can be
damaged.
• Do not activate the cooking zones with
empty cookware or without cookware.
• Do not put aluminium foil on the appliance.
• Cookware made of cast iron, aluminium or
with a damaged bottom can cause
scratches on the glass / glass ceramic.
Always lift these objects up when you have
to move them on the cooking surface.
• This appliance is for cooking purposes only.
It must not be used for other purposes, for
example room heating.
Care and cleaning
• Clean regularly the appliance to prevent the
deterioration of the surface material.
• Deactivate the appliance and let it cool
down before you clean it.
• Disconnect the appliance from the electrical
supply before maintenance.
• Do not use water spray and steam to clean
the appliance.
4 www.zanussi.com
• Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads,
solvents or metal objects.
Disposal
WARNING!
Risk of injury or suffocation.
• Contact your municipal authority for
information on how to discard the appliance
correctly.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
Product description
Cooking surface layout
145 mm
180 mm
210 mm
180 mm
1
1
1 1
2
1
Induction cooking zone
2
Control panel
Control panel layout
1 3 42 5
789 6
Use the sensor fields to operate the appliance. The displays, indicators and sounds tell which
functions operate.
www.zanussi.com 5
Sensor
field
Function Comment
1
ON / OFF To activate and deactivate the hob.
2
/
- To set a heat setting.
3
- Timer indicators of cooking
zones
To show for which zone you set the time.
4
- Timer display To show the time in minutes.
5
- Heat setting display To show the heat setting.
6
Power function To activate and deactivate the function.
7
- To select the cooking zone.
8
/
- To increase or decrease the time.
9
Lock / The Child Safety
Device
To lock / unlock the control panel.
Heat setting displays
Display Description
The cooking zone is deactivated.
-
The cooking zone operates.
Automatic Heat Up function operates.
Power function operates.
+ digit
There is a malfunction.
A cooking zone is still hot (residual heat).
Lock / The Child Safety Device function operates.
Not correct cookware or too small or no cookware on the cooking zone.
Automatic Switch Off function operates.
Residual heat indicator
WARNING!
There is a risk of burns from
residual heat.
The induction cooking zones make the heat
necessary for cooking process directly in the
bottom of the cookware. The glass ceramic is
heated by the heat of the cookware.
6 www.zanussi.com
Daily use
WARNING!
Refer to Safety chapters.
Activating and deactivating
Touch for 1 second to activate or deactivate
the hob.
Automatic Switch Off
The function deactivates the hob
automatically if:
• All cooking zones are deactivated.
• You do not set the heat setting after you
activate the hob.
• You spill something or put something on the
control panel for more than 10 seconds (a
pan, a cloth, etc.). An acoustic signal sounds
and the hob deactivates. Remove the object
or clean the control panel.
• The hob gets too hot (e.g. when, a saucepan
boils dry). Let the cooking zone cool down
before you use the hob again.
• You use incorrect cookware. The symbol
comes on and the cooking zone deactivates
automatically after 2 minutes.
• You do not deactivate a cooking zone or
change the heat setting. After some time
comes on and the hob deactivates. See
below.
The relation between heat setting and
times of the function:
• , 1 - 2— 6 hours
• 3 - 4 — 5 hours
• 5 — 4 hours
• 6 - 9 — 1.5 hours
The heat setting
Touch to increase the heat setting. Touch
to decrease the heat setting. Touch and
at the same time to deactivate the cooking
zone.
Automatic Heat Up
If you activate this function you can get a
necessary heat setting in a shorter time. The
function sets the highest heat setting for some
time and then decreases to the correct heat
setting.
To activate the function the cooking
zone must be cold.
To activate the function for a cooking
zone: touch ( comes on). Immediately
touch ( comes on). Immediately touch
until the correct heat setting comes on. After 3
seconds comes on.
To deactivate the function: touch .
Power function
This function makes more power available to the
induction cooking zones. The function can be
activated for the induction cooking zone only for
a limited period of time. After this time the
induction cooking zone automatically sets back
to the highest heat setting.
Refer to “Technical information”
chapter.
To activate the function for a cooking
zone: touch . comes on.
To deactivate the function: touch or .
Timer
Count Down Timer
You can use this function to set how long the
cooking zone operates for only this one time.
First set the cooking zone then set the
function. You can set the heat setting before
or after you set the function.
To set the cooking zone: touch
again and
again until the indicator of a necessary cooking
zone comes on.
To activate the function or change the
time: touch or of the timer to set the
time (00 - 99 minutes). When the indicator of
the cooking zone starts to flash slowly the time
counts down.
To see the remaining time: set the cooking
zone with . The indicator of the cooking zone
starts to flash quickly. The display shows the
remaining time.
www.zanussi.com 7
To deactivate the function: set the cooking
zone with and touch . The remaining time
counts back to 00. The indicator of the cooking
zone goes out.
When the time comes to an end, the
sound operates and 00 flashes. The
cooking zone deactivates.
To stop the sound: touch .
Minute Minder
You can use this function as a Minute Minder
when the hob is activated and the cooking
zones do not operate (the heat setting display
shows ).
To activate the function: touch
. Touch
or of the timer to set the time. When the
time comes to an end, the sound operates and
00 flashes.
To stop the sound: touch .
The function has no effect on the
operation of the cooking zones.
Lock
You can lock the control panel while cooking
zones operate. It prevents an accidental change
of the heat setting.
Set the heat setting first.
To activate the function: touch . comes
on for 4 seconds.The Timer stays on.
To deactivate the function: touch
. The
previous heat setting comes on.
When you deactivate the hob, you
also deactivate this function.
The Child Safety Device
This function prevents an accidental operation
of the hob.
To activate the function: activate the hob
with . Do not set the heat setting. Touch
for 4 seconds. comes on. Deactivate the
hob with .
To deactivate the function: activate the hob
with . Do not set the heat setting. Touch
for 4 seconds. comes on. Deactivate the
hob with .
To override the function for only one
cooking time: activate the hob with .
comes on. Touch for 4 seconds. Set the
heat setting in 10 seconds. You can operate
the hob. When you deactivate the hob with
the function operates again.
Power management function
• Cooking zones are grouped according to the
location and number of the phases in the
hob (see illustration).
• Each phase has a maximum electricity
loading of 3700 W.
• The function divides the power between
cooking zones connected to the same
phase.
• The function activates when the total
electricity loading of the cooking zones
connected to a single phase exceeds 3700
W.
• The function decreases the power to the
other cooking zones connected to the same
phase.
• The heat setting display of the reduced
zones changes between two levels.
8 www.zanussi.com
Hints and tips
WARNING!
Refer to Safety chapters.
Cookware
For induction cooking zones a
strong electro-magnetic field creates
the heat in the cookware very
quickly.
Use the induction cooking zones
with correct cookware.
Cookware material
• correct: cast iron, steel, enamelled steel,
stainless steel, the bottom made of multi-
layer (with correct mark from a
manufacturer).
• not correct: aluminium, copper, brass,
glass, ceramic, porcelain.
Cookware is correct for an induction hob
if:
• some water boils very quickly on a zone set
to the highest heat setting.
• a magnet pulls on to the bottom of the
cookware.
The bottom of the cookware must be
as thick and flat as possible.
Cookware dimensions
Induction cooking zones adapt to the dimension
of the bottom of the cookware automatically to
some limit.
The cooking zone efficiency is related to the
diameter of the cookware. The cookware with a
smaller diameter than the minimum receives
only a part of the power generated by the
cooking zone.
Refer to “Technical information”
chapter.
The noises during operation
If you can hear:
• crack noise: cookware is made of different
materials (sandwich construction).
• whistle sound: you use one or more cooking
zones with high power levels and the
cookware is made of different materials
(sandwich construction).
• humming: you use high power levels.
• clicking: electric switching occurs.
• hissing, buzzing: the fan operates.
The noises are normal and do not refer to
hob malfunction.
Energy saving
• If it is possible, always put the lids on the
cookware.
• Put cookware on a cooking zone before you
start it.
• Use the residual heat to keep the food warm
or to melt it.
Examples of cooking applications
The relation between the heat setting and the
cooking zone consumption of power is not
linear. When you increase the heat setting it is
not proportional to the increase of the cooking
zone consumption of power. It means that the
cooking zone with the medium heat setting uses
less than a half of its power.
The data in the table is for guidance
only.
Heat setting Use to: Time
(min)
Hints
- 1
Keep cooked food warm. as
neces-
sary
Put a lid on the cookware.
1 - 2 Hollandaise sauce, melt: butter,
chocolate, gelatine.
5 - 25 Mix from time to time.
www.zanussi.com 9
Heat setting Use to: Time
(min)
Hints
1 - 2 Solidify: fluffy omelettes, baked
eggs.
10 -
40
Cook with a lid on.
2 - 3 Simmer rice and milkbased
dishes, heating up ready-cooked
meals.
25 -
50
Add the minimum twice as much
liquid as rice, mix milk dishes
part procedure through.
3 - 4 Steam vegetables, fish, meat. 20 -
45
Add some tablespoons of liquid.
4 - 5 Steam potatoes. 20 -
60
Use max. ¼ l water for 750 g of
potatoes.
4 - 5 Cook larger quantities of food,
stews and soups.
60 -
150
Up to 3 l liquid plus ingredients.
6 - 7 Gentle fry: escalope, veal cordon
bleu, cutlets, rissoles, sausages,
liver, roux, eggs, pancakes,
doughnuts.
as
neces-
sary
Turn halfway through.
7 - 8 Heavy fry, hash browns, loin
steaks, steaks.
5 - 15 Turn halfway through.
9 Boil water, cook pasta, sear meat (goulash, pot roast), deep-fry chips.
Boil large quantities of water. Power function is activated.
Care and cleaning
WARNING!
Refer to Safety chapters.
General information
• Clean the hob after each use.
• Always use cookware with clean bottom.
• Scratches or dark stains on the surface have
no effect on how the hob operates.
• Use a special scraper for the glass.
• Use a special cleaner applicable for the
surface of the hob.
Cleaning of the hob
• Remove immediately: melted plastic,
plastic foil, and food with sugar. If not, the
dirt can cause damage to the hob. Put the
special scraper on the glass surface at an
acute angle and move the blade on the
surface.
• Remove when the hob is sufficiently
cool: limescale rings, water rings, fat stains,
shiny metallic discoloration. Clean the hob
with a moist cloth and some detergent. After
cleaning, rub the hob dry with a soft cloth.
Troubleshooting
WARNING!
Refer to Safety chapters.
10 www.zanussi.com
What to do if...
Problem Possible cause Remedy
You cannot activate or operate
the hob.
The hob is not connected to
an electrical supply or it is
connected incorrectly.
Check if the hob is correctly
connected to the electrical
supply. Refer to the connec-
tion diagram.
The fuse is released. Make sure that the fuse is the
cause of the malfunction. If the
fuse releases again and again,
contact a qualified electrician.
Activate the hob again and set
the heat setting in less than 10
seconds.
You touched 2 or more sensor
fields at the same time.
Touch only one sensor field.
There is water or fat stains on
the control panel.
Clean the control panel.
An acoustic signal sounds and
the hob deactivates.
An acoustic signal sounds
when the hob is deactivated.
You put something on one or
more sensor fields.
Remove the object from the
sensor fields.
The hob deactivates. You put something on the sen-
sor field .
Remove the object from the
sensor field.
Residual heat indicator does
not come on.
The zone is not hot because it
operated only for a short time.
If the zone operated sufficiently
long to be hot, speak to an Au-
thorised Service Centre.
Automatic Heat Up function
does not operate.
The zone is hot. Let the zone become suffi-
ciently cool.
The highest heat setting is set. The highest heat setting has
the same power as the func-
tion.
The heat setting changes be-
tween two levels.
Power management function is
activated.
Refer to "Daily use" chapter.
The sensor fields become hot. The cookware is too large or
you put it too near to the con-
trols.
Put large cookware on the rear
zones if possible.
comes on.
Automatic Switch Off oper-
ates.
Deactivate the hob and acti-
vate it again.
comes on.
The Child Safety Device or the
Lock function operates.
Refer to "Daily use" chapter.
www.zanussi.com 11
Problem Possible cause Remedy
comes on.
There is no cookware on the
zone.
Put cookware on the zone.
The cookware is incorrect. Use the correct cookware.
Refer to “Hints and tips” chap-
ter.
The diameter of the bottom of
the cookware is too small for
the zone.
Use cookware with correct di-
mensions.
Refer to “Technical informa-
tion” chapter.
and a number come on.
There is an error in the hob. Disconnect the hob from the
electrical supply for some time.
Disconnect the fuse from the
electrical system of the house.
Connect it again. If comes
on again, speak to an Author-
ised Service Centre.
comes on.
There is an error in the hob be-
cause a cookware boils dry.
Automatic Switch Off and the
overheating protection for the
zones operate.
Deactivate the hob. Remove
the hot cookware. After ap-
proximately 30 seconds, acti-
vate the zone again. If the
cookware was the problem,
the error message goes out.
Residual heat indicator can
stay on. Let the cookware be-
come sufficiently cool. Check if
your cookware is compatible
with the hob.
Refer to “Hints and tips” chap-
ter.
If you cannot find a solution...
If you cannot find a solution to the problem
yourself, contact your dealer or an Authorised
Service Centre. Give the data from the rating
plate. Give also three digit letter code for the
glass ceramic (it is in the corner of the glass
surface) and an error message that comes on.
Make sure, you operated the hob correctly. If
not the servicing by a service technician or
dealer will not be free of charge, also during the
warranty period. The instructions about the
Service Centre and conditions of guarantee are
in the guarantee booklet.
Installation
WARNING!
Refer to Safety chapters.
Before the installation
Before you install the hob, write down the
information bellow from the rating plate. The
rating plate is on the bottom of the hob.
Serial number ...........................
12 www.zanussi.com
Built-in hobs
Only use the built-in hobs after you assemble
the hob into correct built-in units and work
surfaces that align to the standards.
Connection cable
• Use the correct mains cable of type H05BB-
F Tmax 90°C (or higher) for a single phase
or two phase connection.
• Replace the damaged mains cable with a
special cable (type H05BB-F Tmax 90°C; or
higher). Speak to your local Service Centre.
Assembly
min.
50mm
min.
500mm
min.
2mm
< 20 mm
min. 2 mm
A
B
A
12 mm
28 mm
38 mm
B
57 mm
41 mm
31 mm
min
30 mm
min. 500 mm
> 20 mm
min. 2 mm
A
B
A
12 mm
28 mm
38 mm
B
57 mm
41 mm
31 mm
min. 500 mm
www.zanussi.com 13
R 5mm
min.
55mm
560
+1
mm
490
+1
mm
min.
38 mm
min.
2 mm
min.
38 mm
min.
2 mm
Protection box
If you use a protection box (an additional
accessory), the front airflow space of 2 mm and
the protective floor directly below the hob are
not necessary. The protection box accessory
may not be available in some countries. Please
contact your local supplier.
You can not use the protection box if
you install the hob above an oven.
Technical information
Rating plate
Modell ZEL6640XBA PNC 949 595 597 00
Typ 58 GAP D5 AU 220 - 240 V 50 - 60 Hz
Induction 7.4 kW Made in Germany
Ser.Nr. ................. 7.4 kW
ZANUSSI
14 www.zanussi.com
Cooking zones specification
Cooking zone Nominal power
(maximum
heat setting)
[W]
Power function
[W]
Power function
maximum du-
ration [min]
Cookware di-
ameter [mm]
Left front 2300 3400 10 180 - 210
Left rear 1800 - - 145 - 180
Right front 1400 2500 4 125 - 145
Right rear 1800 - - 145 - 180
The power of the cooking zones can be
different in some small range from the data in
the table. It changes with the material and
dimensions of the cookware.
For optimal cooking results use cookware not
larger than the diameter in the table.
ENVIRONMENTAL CONCERNS
Recycle the materials with the symbol . Put
the packaging in applicable containers to
recycle it. Help protect the environment and
human health and to recycle waste of electrical
and electronic appliances. Do not dispose
appliances marked with the symbol with the
household waste. Return the product to your
local recycling facility or contact your municipal
office.
www.zanussi.com 15
Table des matières
Consignes de sécurité 16
Instructions de sécurité 17
Description de l'appareil 20
Utilisation quotidienne 21
Conseils 24
Entretien et nettoyage 26
En cas d'anomalie de fonctionnement 26
Installation 28
Caractéristiques techniques 30
Sous réserve de modifications.
Consignes de sécurité
Avant d'installer et d'utiliser cet appareil, lisez soigneusement les
instructions fournies. Le fabricant ne peut être tenu pour
responsable des dommages et blessures liés à une mauvaise
installation ou utilisation. Conservez toujours cette notice avec
votre appareil pour vous y référer ultérieurement.
Sécurité des enfants et des personnes vulnérables
• Cet appareil peut être utilisé par des enfants de plus de 8 ans,
ainsi que des personnes dont les capacités physiques,
sensorielles et mentales sont réduites ou dont les
connaissances et l'expérience sont insuffisantes, à condition
d'être surveillés ou d'avoir reçu des instructions concernant
l'utilisation sécurisée de l'appareil et de comprendre les risques
encourus.
• Ne laissez pas les enfants jouer avec l'appareil.
• Ne laissez pas les emballages à la portée des enfants.
• Tenez les enfants et les animaux éloignés de l'appareil lorsqu'il
est en cours de fonctionnement ou lorsqu'il refroidit. Les parties
accessibles sont chaudes.
• Si l'appareil est équipé d'un dispositif de sécurité enfants, nous
vous recommandons de l'activer.
• Les enfants ne doivent pas nettoyer ni entreprendre une
opération de maintenance sur l'appareil sans surveillance.
• Les enfants de moins de 3 ans, sans surveillance, doivent être
tenus à l'écart de l'appareil.
16 www.zanussi.com
Sécurité générale
• L'appareil et ses parties accessibles deviennent chauds
pendant son fonctionnement. Ne touchez pas les résistances.
• Ne faites pas fonctionner l'appareil avec un minuteur externe ou
un système de commande à distance.
• Il peut être dangereux de laisser chauffer de la graisse ou de
l'huile sans surveillance sur une table de cuisson car cela
pourrait provoquer un incendie.
• N'essayez jamais d'éteindre un feu avec de l'eau. Éteignez
l'appareil puis couvrez les flammes, par exemple avec un
couvercle ou une couverture ignifuge.
• N'entreposez rien sur les surfaces de cuisson.
• Ne posez pas d'objets métalliques tels que couteaux,
fourchettes, cuillères ou couvercles sur la table de cuisson car
ils pourraient chauffer.
• N'utilisez pas de nettoyeur vapeur pour nettoyer l'appareil.
• Après utilisation, éteignez toujours la zone de cuisson à l'aide
de la manette de commande correspondante et ne vous fiez
pas à la détection des récipients.
• Si la surface vitrocéramique est fissurée, éteignez l'appareil
pour éviter tout risque d'électrocution.
• Si le câble d'alimentation est endommagé, il doit être remplacé
par le fabricant, un service de maintenance agréé ou un
technicien qualifié afin d'éviter tout danger.
Instructions de sécurité
Installation
AVERTISSEMENT!
L'appareil doit être installé
uniquement par un professionnel
qualifié.
• Retirez l'intégralité de l'emballage.
• N'installez pas et ne branchez pas un
appareil endommagé.
• Suivez scrupuleusement les instructions
d'installation fournies avec l'appareil.
• Respectez l'espacement minimal requis par
rapport aux autres appareils et éléments.
• Soyez toujours vigilants lorsque vous
déplacez l'appareil car il est lourd. Portez
toujours des gants de sécurité.
• Isolez les surfaces découpées à l'aide d'un
matériau d'étanchéité pour éviter que la
moisissure ne provoque des gonflements.
• Protégez la partie inférieure de l'appareil de
la vapeur et de l'humidité.
• N'installez pas l'appareil près d'une porte ou
sous une fenêtre. Les récipients chauds
risqueraient de tomber de l'appareil lors de
l'ouverture de celles-ci.
• Si l'appareil est installé au-dessus de tiroirs,
assurez-vous qu'il y a suffisamment d'espace
entre le fond de l'appareil et le tiroir
supérieur pour que l'air puisse circuler.
• Le dessous de l'appareil peut devenir très
chaud. Veillez à installer un panneau de
www.zanussi.com 17
séparation ignifuge sous l'appareil pour en
bloquer l'accès.
• Assurez-vous de laisser un espace de
ventilation de 2 mm entre le plan de travail et
l'avant de l'unité qui se trouve dessous. La
garantie ne couvre pas les dommages
causés par l'absence d'un espace de
ventilation adéquat.
Branchement électrique
AVERTISSEMENT!
Risque d'incendie ou
d'électrocution.
• L'ensemble des branchements électriques
doit être effectué par un technicien qualifié.
• L'appareil doit être relié à la terre.
• Avant toute intervention, assurez-vous que
l'appareil est débranché.
• Vérifiez que les données électriques figurant
sur la plaque signalétique correspondent à
celles de votre réseau. Si ce n'est pas le cas,
contactez un électricien.
• Assurez-vous que l'appareil est bien installé.
Un câble d'alimentation lâche et inapproprié
ou une fiche (si présente) non serrée
peuvent être à l'origine d'une surchauffe des
bornes.
• Utilisez le câble d'alimentation électrique
approprié.
• Ne laissez pas le câble d'alimentation
s'emmêler.
• Assurez-vous qu'une protection anti-
électrocution est installée.
• Utilisez un collier anti-traction sur le câble.
• Assurez-vous que le câble d'alimentation ou
la fiche (si présente) n'entrent pas en
contact avec les surfaces brûlantes de
l'appareil ou les récipients brûlants lorsque
vous branchez l'appareil à des prises
électriques situées à proximité.
• N'utilisez pas d'adaptateurs multiprises ni de
rallonges.
• Veillez à ne pas endommager la fiche
secteur (si présente) ni le câble
d'alimentation. Contactez un service après-
vente agréé ou un électricien pour remplacer
le câble d'alimentation s'il est endommagé.
• La protection contre les chocs des parties
sous tension et isolées doit être fixée de telle
manière qu'elle ne puisse pas être enlevée
sans outils.
• Ne branchez la fiche d'alimentation à la prise
de courant qu'à la fin de l'installation.
Assurez-vous que la prise de courant est
accessible une fois l'appareil installé.
• Si la prise de courant est lâche, ne branchez
pas la fiche d'alimentation secteur.
• Ne tirez jamais sur le câble d'alimentation
pour débrancher l'appareil. Tirez toujours sur
la fiche.
• N'utilisez que des systèmes d'isolation
appropriés : des coupe-circuits, des fusibles
(les fusibles à visser doivent être retirés du
support), un disjoncteur différentiel et des
contacteurs.
• L'installation électrique doit être équipée
d'un dispositif d'isolement à coupure
omnipolaire. Le dispositif d'isolement doit
présenter une distance d'ouverture des
contacts d'au moins 3 mm.
Utilisation
AVERTISSEMENT!
Risque de blessures, de brûlures ou
d'électrocution.
• Avant la première utilisation, retirez les
emballages, les étiquettes et les films de
protection (si présents).
• Utilisez cet appareil dans un environnement
domestique.
• Ne modifiez pas les caractéristiques de cet
appareil.
• Assurez-vous que les orifices de ventilation
ne sont pas bouchés.
• Ne laissez jamais l'appareil sans surveillance
pendant son fonctionnement.
• Éteignez les zones de cuisson après chaque
utilisation.
• Ne vous fiez pas uniquement au détecteur
de récipient.
• Ne posez pas de couverts ou de couvercles
sur les zones de cuisson. Elles sont
chaudes.
• N'utilisez jamais cet appareil avec les mains
mouillées ou lorsqu'il est en contact avec de
l'eau.
• N'utilisez jamais l'appareil comme plan de
travail ou comme plan de stockage.
• Si la surface de l'appareil présente des
fêlures, débranchez immédiatement l'appareil
pour éviter tout risque d'électrocution.
• Les porteurs de pacemakers doivent rester à
une distance minimale de 30 cm des zones
de cuisson à induction lorsque l'appareil est
en cours de fonctionnement.
• Lorsque vous versez un aliment dans de
l'huile chaude, elle peut éclabousser.
18 www.zanussi.com
AVERTISSEMENT!
Risque d'incendie et d'explosion.
• Les graisses et l'huile chaudes peuvent
dégager des vapeurs inflammables. Tenez
les flammes ou les objets chauds éloignés
des graisses et de l'huile lorsque vous vous
en servez pour cuisiner.
• Les vapeurs dégagées par l'huile très
chaude peuvent provoquer une combustion
spontanée.
• L'huile qui a servi contient des restes
d'aliments pouvant provoquer un incendie à
température plus faible que l'huile n'ayant
jamais servi.
• Ne placez pas de produits inflammables ou
d'éléments imbibés de produits inflammables
à l'intérieur ou à proximité de l'appareil, ni sur
celui-ci.
AVERTISSEMENT!
Risque d'endommagement de
l'appareil.
• Ne laissez pas de récipients chauds sur le
bandeau de commande.
• Ne laissez pas le contenu des récipients de
cuisson s'évaporer complètement.
• Prenez soin de ne pas laisser tomber
d'objets ou de récipients sur l'appareil. Sa
surface risque d'être endommagée.
• Ne faites jamais fonctionner les zones de
cuisson avec des récipients de cuisson
vides ou sans aucun récipient de cuisson.
• Ne placez jamais de papier aluminium sur
l'appareil.
• N'utilisez pas de récipients en fonte ou en
aluminium, ni de récipients dont le fond est
endommagé et rugueux. Ils risqueraient de
rayer le verre ou la surface vitrocéramique.
Soulevez toujours ces objets lorsque vous
devez les déplacer sur la surface de cuisson.
• Cet appareil est exclusivement destiné à un
usage culinaire. Ne l'utilisez pas pour des
usages autres que celui pour lequel il a été
conçu, à des fins de chauffage par exemple.
Entretien et nettoyage
• Nettoyez régulièrement l'appareil afin de
maintenir le revêtement en bon état.
• Éteignez l'appareil et laissez-le refroidir avant
de le nettoyer.
• Débranchez l’appareil de l'alimentation
électrique avant toute opération de
maintenance.
• Ne pulvérisez pas d'eau ni de vapeur pour
nettoyer l'appareil.
• Nettoyez l'appareil avec un chiffon doux
humide. Utilisez uniquement des produits de
lavage neutres. N'utilisez pas de produits
abrasifs, de tampons à récurer, de solvants
ni d'objets métalliques.
Mise au rebut
AVERTISSEMENT!
Risque de blessure ou d'asphyxie.
• Contactez votre service municipal pour
obtenir des informations sur la marche à
suivre pour mettre l'appareil au rebut.
• Débranchez l'appareil de l'alimentation
électrique.
• Coupez le câble d'alimentation et mettez-le
au rebut.
www.zanussi.com 19
Description de l'appareil
Description de la table de cuisson
145 mm
180 mm
210 mm
180 mm
1
1
1 1
2
1
Zone de cuisson à induction
2
Panneau de commande
Description du bandeau de commande
1 3 42 5
789 6
Les touches sensitives permettent de faire fonctionner l'appareil. Les affichages, les voyants et les
signaux sonores indiquent les fonctions activées.
Touche
sensi-
tive
Fonction Commentaire
1
MARCHE/ARRÊT Pour allumer et éteindre la table de cuisson.
2
/
- Pour sélectionner un niveau de cuisson.
3
- Voyants du minuteur des
zones de cuisson
Pour indiquer la zone à laquelle se réfère la du-
rée sélectionnée.
4
- Affichage du minuteur Pour indiquer la durée, en minutes.
20 www.zanussi.com
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Zanussi ZEL6640XBA Manuel utilisateur
- Catégorie
- Plaques de cuisson
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Zanussi ZEL6640XBA User manual
Documents connexes
-
Zanussi ZEI3921 Manuel utilisateur
-
Zanussi ZEL6640XBA Manuel utilisateur
-
Zanussi ZVM64X Manuel utilisateur
-
-
Zanussi ZEI6740BBA Manuel utilisateur
-
-
-
-
-