Yamaha MSP7 STUDIO Le manuel du propriétaire

Marque: Yamaha

Modèle: MSP7 STUDIO

Catégorie: Haut-parleurs

Taper: Le manuel du propriétaire

Ce manuel convient également à

Powered Near-field Reference Monitors & Subwoofer

OWNER’S MANUAL

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

MANUAL DE INSTRUCCIONES

MSP

series

Powered Monitor Speaker

MSP7 STUDIO

MSP5 STUDIO

Powered Subwoofer

SW10 STUDIO

The above warning is located on the rear of the unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to alert

the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufﬁcient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

ampliﬁers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not ﬁt into your outlet, consult

an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 Only use attachments/accessories speciﬁed by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table speciﬁed

by the manufacturer, or sold with

the apparatus. When a cart is

used, use caution when moving

the cart/apparatus combination

to avoid injury from tip-over.

13 Unplug this apparatus during

lightning storms or when unused for long periods of

time.

14 Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

(98-6500)

(3 wires)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

IMPORTANT

Please record the serial number of this unit in the space below.

Model:

Serial No.:

The serial number is located on the bottom or rear of the unit.

Retain this Owner's Manual in a safe place for future reference.

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in

accordance with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be

connected to the terminal in the plug which is marked by the letter

E or by the safety earth symbol or colored GREEN or GREEN-

and-YELLOW.

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

FrançaisEspañol EnglishDeutsch

Contents

Precautions

Setting Up for Superior Monitor Sound

Control and Functions

MSP7 STUDIO, MSP5 STUDIO

SW10 STUDIO

Specifications

Dimensions

Performance graph

Block Diagram

Inhalt

Vorsichtsmaßnahmen

Aufstellung für den besten Klang

Bedienelemente und Funktionen

MSP7 STUDIO, MSP5 STUDIO

SW10 STUDIO

Technische Daten

Abmessungen

Leistungs diagramm

Blockschaltbild

Table des matières

Précautions

Configuration du son de contrôle supérieur

Commandes et fonctions

MSP7 STUDIO, MSP5 STUDIO

SW10 STUDIO

Spécifications

Dimensions

Graphique des performances

Schéma d’ensemble

Contenido

Precauciones

Configuración para obtener una monitorización de

sonido excelente

Mandos y funciones

MSP7 STUDIO, MSP5 STUDIO

SW10 STUDIO

Especificaciones

Dimensiones

Gráfico de rendimiento

Diagrama de bloques

MSP7 STUDIO, MSP5 STUDIO

SW10 STUDIO

Thank you for choosing a YAMAHA powered monitor speaker or powered subwoofer.

In order to take maximum advantage of the speaker’s features and ensure maximum performance and longevity,

please read this manual carefully before using powered monitor speaker or powered subwoofer.

Keep the manual in a safe place for future reference.

Vielen Dank dass Sie sich für einen aktiven Monitorlautsprecher oder Subwoofer von YAMAHA entschieden haben.

Um die Eigenschaften des Lautsprechers optimal zu nutzen und für höchste Leistung und Lebensdauer lesen Sie diese Anleitung

bitte genau durch, bevor Sie den aktiven Monitorlautsprecher oder Subwoofer verwenden.

Bitte bewahren Sie diese Bedienungsanleitung zum späteren Nachschlagen an einem sicheren Ort auf.

Nous vous remercions d’avoir choisi un haut-parleur de contrôle ou un caisson de basses ampliﬁé YAMAHA.

Pour obtenir les performances optimales de vos haut-parleurs et garantir une longévité maximale, lisez attentivement ce mode

d’emploi avant d’utiliser le haut-parleur de contrôle ou le caisson de basses ampliﬁé.

Conservez-le en lieu sûr pour pouvoir vous y référer ultérieurement.

Gracias por elegir los monitores o el subwoofer autoampliﬁcados de Yamaha.

A ﬁn de aprovechar al máximo las características de los altavoces y obtener un rendimiento y durabilidad óptimos,

lea atentamente este manual antes de utilizar el sistema.

Guarde este manual en un lugar seguro para futuras consultas.

(5)-4

English

MSP7 STUDIO/MSP5 STUDIO/SW10 STUDIO Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-

circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Only use the voltage speciﬁed as correct for the device. The required voltage is printed on

the name plate of the device.

• Use only the included power cord.

• Do not place the power cord near heat sources such as heaters or radiators, and do not

excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a

position where anyone could walk on, trip over, or roll anything over it.

• Be sure to connect to an appropriate outlet with a protective grounding connection.

Improper grounding can result in electrical shock.

• Do not open the device or attempt to disassemble the internal parts or modify them in any

way. The device contains no user-serviceable parts. If it should appear to be malfunctioning,

discontinue use immediately and have it inspected by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet conditions, or place

containers on it containing liquids which might spill into any openings.

• Never insert or remove an electric plug with wet hands.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden loss of sound

during use of the device, or if any unusual smells or smoke should appear to be caused by

it, immediately turn off the power switch, disconnect the electric plug from the outlet, and

have the device inspected by qualiﬁed Yamaha service personnel.

• If this device should be dropped or damaged, immediately turn off the power switch,

disconnect the electric plug from the outlet, and have the device inspected by qualiﬁed

Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other

property. These precautions include, but are not limited to, the following:

• Remove the electric plug from the outlet when the device is not to be used for extended

periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold the plug itself and

not the cord. Pulling by the cord can damage it.

• Before moving the device, remove all connected cables.

• When setting up the device, make sure that the AC outlet you are using is easily accessible.

If some trouble or malfunction occurs, immediately turn off the power switch and disconnect

the plug from the outlet.

• Do not use the device in a conﬁned, poorly-ventilated location. Make sure that there is

adequate space between the device and surrounding walls or other devices: for MSP7

STUDIO and MSP5 STUDIO at least 15cm at the sides, 15cm behind and 15cm above, and

for SW10 STUDIO at least 50cm at the sides, 50cm behind and 50 above. Inadequate

ventilation can result in overheating, possibly causing damage to the device(s), or even ﬁre.

• Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in

direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel

disﬁguration or damage to the internal components.

• Do not place the device in an unstable position where it might accidentally fall over.

• Before connecting the device to other devices, turn off the power for all devices. Before

turning the power on or off for all devices, set all volume levels to minimum.

• When turning on the AC power in your audio system, always turn on the device LAST, to

avoid speaker damage. When turning the power off, the device should be turned off FIRST

for the same reason.

• Do not insert your ﬁngers or hands in any gaps or openings on the device (ports, etc.).

•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or

openings on the device (ports, etc.) If this happens, turn off the power immediately and

unplug the power cord from the AC outlet. Then have the device inspected by qualiﬁed

Yamaha service personnel.

• Do not use the device for a long period of time at a high or uncomfortable volume level,

since this can cause permanent hearing loss. If you experience any hearing loss or ringing

in the ears, consult a physician.

• Do not operate the device if the sound is distorting. Prolonged use in this condition could

cause overheating and result in ﬁre.

• Do not rest your weight on the device or place heavy objects on it, and avoid use excessive

force on the buttons, switches or connectors.

• When removing the speaker from the box or handling it at any time, be careful not to touch

the tweeter dome with your ﬁngers. Otherwise, the speaker can be damaged.

Even though this speaker system is magnetically shielded, you may need to move the speaker further away from the video monitor, if a nearby video monitor exhibits any distortion or unnatural color

shift.

Interference From Cell Phones

Using a cell phone near the speaker system can induce noise. If this occurs, move the cell phone further away from the speaker system.

The rubber feet included in this package can be attached to the MSP5 STUDIO and MSP7 STUDIO to prevent slippage when it is to be used on a slippery surface.

Air blowing out of the bass reﬂex ports is normal, and often occurs when the speaker is handling program material with heavy bass content.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualiﬁed Yamaha service personnel about replacing

defective components.

• Illustrations in this manual are for explanatory purposes only, and may not match the actual appearance of the product during operation.

• Company names and product names used in this Owner’s Manual are trademarks or registered trademarks of their respective owners.

• Speciﬁcations and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or speciﬁcations at any time without prior notice. Since speciﬁcations,

equipment or options may not be the same in every locale, please check with your Yamaha dealer.

Power supply/Power cord

Do not open

Water warning

If you notice any abnormality

Power supply/Power cord

Location

Connections

Handling caution

XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device.

English

MSP7 STUDIO/MSP5 STUDIO/SW10 STUDIO Owner’s Manual

Setting Up for Superior

Monitor Sound

Setting Up for Superior

Monitor Sound

Unlike most other audio and production gear, the way speakers are set up in a room has a dra-

matic effect on the ﬁnal sound. This short tutorial provides a basic guide to help you maximize

the performance of your Yamaha MSP-series monitor speakers.

Listening vs. Monitoring

You’d think that the requirements for "listening" and

"monitoring" would be the same, but that is not always the

case. A great listening system can be a great monitoring

system, and vice-versa, but in most cases you’ll miss details

that are essential to producing the best possible mix on a

system that’s set up purely for musical enjoyment. The dif-

ference is somewhat similar to the difference between a

retouched glamour portrait and the original in which every

blemish is clearly visible. The model looks a lot better in the

retouched photo, but the reality is in the original un-

enhanced version. As mixing engineer, or producer, or

sonic artist, you’ll want to hear the details so that you can

create a perfectly balanced mix that will sound good on

the widest possible range of audio systems — and that can

mean anything from high-ticket boutique audio compo-

nents in a properly-designed listening room right down to

the boom box on top of the fridge in the kitchen. You

don’t want problems hidden by poor monitor perfor-

mance to sabotage your sound on other systems.

The legendary Yamaha NS10M became a standard

monitor in the music and sound industry (and is still in use

in many studios throughout the world) for precisely that

reason: it offered ﬂat response and excellent resolution that

allowed engineers and producers to hear subtle details that

make the difference between good and great sound. The

MSP-series monitors carry on the tradition with accuracy

and detail that can help you make great mixes, while let-

ting you monitor for long stretches with minimum fatigue.

If you’re connecting your MSP speak-

ers directly to a mixer such as one of the

Yamaha MG-series mixers, they should

usually be connected to the mixer’s "C-R"

outputs or MONITOR outputs so that

you can control the monitor level with-

out affecting the level of the signal sent

to the mixer’s main bus, which will usu-

ally be feeding your recorder or DAW

(Digital Audio Workstation) in a produc-

tion type setup.

input

C-R

OUT

RST

OUT

MG Series

English

MSP7 STUDIO/MSP5 STUDIO/SW10 STUDIO Owner’s Manual

Speaker Placement

Speaker placement is one of the most important consid-

erations when setting up a monitor system, but it is all too

often overlooked with the result that performance is seri-

ously compromised. Admittedly the obstacles to perfect

speaker positioning in the small studio are formidable.

Having the space available to place your speaker system so

that it can provide optimum performance is a luxury, but it

is deﬁnitely worth the time spent doing a little experimen-

tation and measuring to make the most of limited

resources. The difference can be astounding. The basics are

the same whether you’re setting up a stereo or 5.1 sur-

round system.

Proximity to Walls and Corners

For the most accurate response your speakers should be

positioned away from walls and especially corners, which

can play havoc with a speaker’s frequency characteristics. A

minimum of about 1.5 meters (about 5 feet) away from

walls would be ideal, but in reality they’ll probably end up

being placed on a desktop and pushed up against a wall.

Just keep in mind that fact that the closer you get to

walls and corners the more exaggerated the speaker’s bass

response is likely to become, and some compensation —

whether you compensate mentally or use some equaliza-

tion — will probably be required.

Symmetry

As we’ve just learned, the response of a speaker can

change drastically according to where it is placed in rela-

tion to surfaces. So what happens if one of your speakers is

up against a wall and the other is out in the open? Rest

assured that the results will not be good, and will deﬁnitely

not be conducive to producing good mixes.

You’ll have totally different response from your left and

right speakers, making it next to impossible to create a

well-balanced mix, or even position tracks accurately in the

stereo sound ﬁeld. So whatever you do, if you’re serious

about your sound make sure that your speakers are located

as symmetrically within your listening environment as pos-

sible. Use a tape measure to ensure that your speakers are

the same distance from the side and rear walls. Large

objects can throw the acoustic symmetry of a room off bal-

ance, too. It’s also important to be aware of the location of

doors and windows. It is not always possible to achieve

ideal symmetry, but it’s worth getting as close as possible.

English

MSP7 STUDIO/MSP5 STUDIO/SW10 STUDIO Owner’s Manual

The “Sweet Spot”

For both stereo and surround mixing your position in

relation to the main front speakers — the "sweet spot" as

it’s often called — should be one apex of an equilateral tri-

angle. In other words your distance from either speaker

should be the same as the distance between the two

speakers. The speakers should also be "toed in" to the cor-

responding 60° angle so that the drivers are aimed directly

at the listening position. The height of the speakers should

be such that the tweeters are roughly aligned with your

ears (this is because high frequencies are the most direc-

tional).

Fine-tuning for Stereo

(MSP7 STUDIO or MSP5 STUDIO x 2)

● The speaker LEVEL controls should be set to the same level. A setting of about 12 o’clock corresponds to a nominal

input level.

● Since no subwoofer is being used in this setup, if your speakers have a LOW CUT switch, set it to "FLAT" (the MSP7

STUDIO has a LOW CUT switch).

● For accurate monitoring set the LOW TRIM switch to "0". If you want to reduce the low-frequency level a bit set the

switch to "-1.5".

● For accurate monitoring set the HIGH TRIM switch to "0". This switch can be set to "-1.5 dB" to attenuate the highs

slightly if you ﬁnd the sound too bright.

60˚

English

MSP7 STUDIO/MSP5 STUDIO/SW10 STUDIO Owner’s Manual

Adding a Subwoofer

Even if you don’t plan to set up a surround system, add-

ing a subwoofer can be a real advantage for stereo mixing.

If you can’t hear the extreme low end there’s not much

you can do to make it sound great. The extended bass

response provided by a good subwoofer can indeed help

you to improve the overall quality of your mixes.

The location of your subwoofer is not as critical as the main

speakers, because frequencies below around 200 Hz — the

region your subwoofer will be working in — aren’t direc-

tional. To say it another way, the ear can’t locate the source

of such low frequencies, so in theory the subwoofer can be

placed anywhere in the room. In reality it’s a good idea to

place the subwoofer on the ﬂoor somewhere between the

main front speakers at the same distance from the listening

position as the main speakers, but it doesn’t have to be

dead center.

Fine-tuning for Stereo + Subwoofer

(MSP7 STUDIO or MSP5 STUDIO x 2, SW10 STUDIO x 1)

● Set the MSP7 STUDIO or MSP5 STUDIO LEVEL control to about 12 o’clock for nominal input level. If you’re using the

MSP7 STUDIO set the SW10 STUDIO LEVEL control to about 12 o’clock, and if you’re using the MSP5 STUDIO set it to

about 10 o’clock. You can then ﬁne-adjust the SW10 STUDIO LEVEL control as required. Another approach would be to

adjust the MSP7 STUDIO/MSP5 STUDIO output level to achieve the desired relative balance with the subwoofer.

● Start with the SW10 STUDIO HIGH CUT control set at its center click position, which corresponds to a HPF frequency of

about 80 Hz. The HIGH CUT frequency can be adjusted later to achieve the smoothest integration with the MSP7 STU-

DIO or MSP5 STUDIO speakers.

● If you are using the MSP7 STUDIO, set the LOW CUT switch to "80".

● úFor accurate monitoring set the MSP7 STUDIO/MSP5 STUDIO LOW TRIM switch to "0". If you want to reduce the

level of the low-frequency range, set the switch to "-1.5".

● For accurate monitoring set the MSP7 STUDIO/MSP5 STUDIO HIGH TRIM switch to "0". This switch can be set to "-1.5

dB" to attenuate the highs slightly if you ﬁnd the sound too bright.

Setting Up for Surround

If you’re going to be mixing for surround, obviously

you’ll need a surround monitoring system. For a 5.1 sur-

round system, for example, you only need to add a center

speaker and two rear speakers to the stereo + subwoofer

system described in the previous section. Let’s see … two

main speakers plus one center speaker plus two rear speak-

ers is a total of ﬁve speakers, and ".1" refers to the sub-

woofer. All present and accounted for!

According to the ITU (International Telecommunications

Union) speciﬁcations for 5.1 surround setup, the main

front speakers are positioned in the 60° equilateral triangle

relationship to the listening position described earlier, and

the rear speakers should be located at the same distance

from the listening position, but at an angle of between

100° and 120°, as shown in the diagram above. The center

speaker should be placed precisely midway between the

main front speakers, at the same distance from the listen-

ing position as the other speakers (which means that ide-

ally it will be a bit behind the main left and right speakers).

SUBWOOFER

English

MSP7 STUDIO/MSP5 STUDIO/SW10 STUDIO Owner’s Manual

As you may have deduced by now, the main left and right,

center, and rear speakers are all located on the circumfer-

ence of a circle with its center at the listening position. An

easy way to get all the distances right is to use a piece of

string cut or marked to the exact distance between the

main left and right speakers. Attach the string to a mic

stand or other convenient object at the listening position

and use it to measure the distance from the listening posi-

tion to each of the speakers. Stretched from the listening

position to the speaker position the string will also provide

a convenient guide for aligning the speakers so that they

point directly at the listening position.

MG-series Mixer Setup

If you’re connecting to a standard mixer that is not speciﬁ-

cally designed for surround production, your main L and R

speakers can be connected to any convenient stereo output

pair via the SW10 STUDIO subwoofer, while the center and rear

speakers will be connected to individual output channels.

Example: MG16/6FX

Digital Mixer Setup

If you’re connecting your MSP-series speakers to a mixing

console that features built-in surround handling capability —

such as the Yamaha DM2000, DM1000, or 02R96 — each

speaker will be connected directly to the console output dedi-

cated to handling that particular surround channel. In this type

of setup you can take full advantage of the console’s advanced

surround mixing and bass management facilities.

DVD

Player

Input Channel

Output

Connector

Speaker

L ➔ Ch1 (ST=ON, PAN ➔ L) ➔ ST OUT (L) ➔ L

R ➔ Ch2 (ST=ON, PAN ➔ R) ➔ ST OUT (R) ➔ R

LS ➔ Ch3 (GRP1-2, PAN ➔ L) ➔ GROUP OUT 1(L) ➔ LS

RS ➔ Ch4 (GRP1-2, PAN ➔ R) ➔ GROUP OUT 2(R) ➔ RS

C ➔ Ch5 (GRP3-4, PAN ➔ L) ➔ GROUP OUT 3 ➔ C

LFE ➔

Ch6 (ST=ON, PAN➔Center,

Fader➔+10 dB Boost)

➔ ST OUT ➔

SUBWOOFER

6 Channel Line

DVD Player

SUBWOOFER

English

MSP7 STUDIO/MSP5 STUDIO/SW10 STUDIO Owner’s Manual

Fine-tuning for Surround

(MSP7 STUDIO or MSP5 STUDIO x 5, SW10 STUDIO x 1)

● Set the MSP7 STUDIO or MSP5 STUDIO LEVEL control to about 12 o’clock for nominal input level. If you’re using the

MSP7 STUDIO set the SW10 STUDIO LEVEL control to about 1 o’clock*, and if you’re using the MSP5 STUDIO set it to

about 11 o’clock*. You can then ﬁne-adjust the SW10 STUDIO LEVEL control as required. Another approach would be

to adjust the MSP7 STUDIO/MSP5 STUDIO output level to achieve the desired relative balance with the subwoofer.

* If you’re using the MSP7 STUDIO with a digital mixer, set the SW10 STUDIO LEVEL control to about 12 o’clock. If you’re

using the MSP5 STUDIO with a digital mixer set the SW10 STUDIO LEVEL control to about 10 o’clock.

● Start with the HIGH CUT control set at about 2:30, which corresponds to a HPF frequency of about 100 Hz*. The HIGH

CUT frequency can be adjusted later to achieve the smoothest integration with the MSP7 STUDIO or MSP5 STUDIO

speakers.

* Set to 80 Hz if you’re using a digital mixer.

● If you are using the MSP7 STUDIO set the LOW CUT switch to "100 Hz"*.

* Set to 80 Hz if you’re using a digital mixer.

● For accurate monitoring set the MSP7 STUDIO/MSP5 STUDIO HIGH TRIM switch to "0". This switch can be set to "-1.5

dB" to attenuate the highs slightly if you ﬁnd the sound too bright.

Maintain a Consistent Monitoring Level

Another difference between listening and monitoring is

that when you’re listening for enjoyment you probably lis-

ten at signiﬁcantly different levels at different times: from

soft and unobtrusive for background music, right though

room-shaking for involved listening or dancing. This is def-

initely not the case for serious monitoring. The response of

your ears changes so drastically according to level, espe-

cially in the soft to medium-loud region, that is essential to

maintain a consistent monitoring level otherwise you sim-

ply won’t get consistent mixing results. You’ll undoubtedly

need to turn up or down a bit at certain points during the

production process when listening for speciﬁc problems or

effects — in fact it is important to listen to your mix at dif-

ferent levels as a ﬁnal checking process, bringing the levels

down very low to check if any elements of the mix disap-

pear and make sure that the vocal continues to maintain its

balance in the mix at very low levels — but in general you

should stay within a fairly small range.

Just what is the best level to monitor at? Although there

is a "standard" monitoring level speciﬁcation,* the answer

for most small studios is "whatever is most comfortable for

you." You need to monitor at a level that’s loud enough so

that you don’t miss any soft details, but not so loud that

your ears become fatigued (or your neighbors complain). If

you ﬁnd yourself turning up the volume after monitoring

for a short while, your ears are probably starting to get

tired and losing sensitivity. This is obviously bad for your

music as well as your ears. So ﬁnd that "comfort zone" and

prepare to make some great music.

*For you techies, the SMPTE RP 200 standard monitoring level is

83 dB SPL (RMS average) at the listening position, or if you’re

mixing for ﬁlm you’ll need to know that the standard Dolby

monitoring level for surround is 85 dB SPL.

English

MSP7 STUDIO/MSP5 STUDIO/SW10 STUDIO Owner’s Manual

Controls and Functions

MSP7 STUDIO, MSP5 STUDIO

1 POWER switch

Tur ns power to the speaker on or off. When the power is

turned on the POWER indicator (8) on the front panel will

light green.

2 AC IN Connector

Connect the supplied power cable here. First connect the

power cord to the speaker, then insert the power cord plug

into the AC outlet.

3 LOW TRIM switch

Adjusts the level of low-frequency range.

MSP7 STUDIO:

With the "+1.5" setting, low frequencies around 45 Hz are

boosted by 1.5 dB. With the "-1.5" and "-3" settings the

same frequency range is cut by 1.5 dB or 3 dB, respec-

tively.

MSP5 STUDIO:

With the "+1.5" setting, low frequencies around 60 Hz are

boosted by 1.5 dB. With the "-1.5" and "-3" settings, the

same frequency range is cut by 1.5 dB and 3 dB, respec-

tively.

4 HIGH TRIM switch

Adjusts the level of high-frequency range.

With the "+1.5" setting, the range around 15 kHz is boosted by

1.5 dB. With the "-1.5" setting, the range around 15 kHz is cut

by 1.5 dB.

5 LOW CUT switch (MSP7 STUDIO)

Cuts the low-frequency range. With the "80 Hz" setting the

range below 80 Hz is cut. With the "100 Hz" setting the range

below 100 Hz is cut.

6 INPUT 1/2 connector

These are balanced XLR-type and unbalanced phone-type

input connectors.

The MSP7 STUDIO only has an XLR-type input connector.

Do NOT use both the XLR and Phone type connector at the

same time. Please connect to only one of these connectors.

7 LEVEL control

Adjusts the overall output level.

8 POWER indicator

When the power is turned on the POWER indicator will light

green. The power indicator will ﬂash red to indicate clipping.

MSP5 STUDIO(Rear Panel)

(Front Panel)

MSP7 STUDIO(Rear Panel)

(Front Panel)

English

MSP7 STUDIO/MSP5 STUDIO/SW10 STUDIO Owner’s Manual

SW10 STUDIO

1 POWER switch

Tur ns power to the speaker on or off. When the power is

turned on the POWER indicator (8) on the front panel will

light green.

2 AC IN Connector

Connect the supplied power cable here. First connect the

power cord to the subwoofer, then insert the power cord plug

into the AC outlet.

3 PHASE switch

Selects a phase of output sound from the SW10 STUDIO.

You will usually set this switch to "NORM". However, the "REV."

setting may improve low-range response, depending on the

type and location of the entire speaker system. Try both set-

tings and select the one that produces the best low-end

sound.

4 HIGH CUT control

Use the HIGH CUT control to set the cutoff frequency of the

signal output from the SW10 STUDIO from 40 Hz to 120 Hz.

5 LEVEL control

Adjusts the overall output level.

6 INPUT L/R/SUBWOOFER connector

These are balanced XLR-type input connectors. Three differ-

ent signals can be simultaneously input via these connectors.

The input signals are mixed before being sent to the sub-

woofer.

7 OUTPUT L/R/SUBWOOFER connector

These XLR-type balanced output connectors output the sig-

nals received at the INPUT L/R/SUBWOOFER connectors,

respectively.

8 POWER indicator

When the power is turned on the POWER indicator will light

green. The power indicator will ﬂash red to indicate clipping.

43 5

SW10 STUDIO

(Rear Panel)

(Front Panel)

FrançaisEspañol EnglishDeutsch

Speciﬁcations

* These speciﬁcations apply to rated power supplies of 100, 120, 230 and 240 V.

MODEL MSP7 STUDIO MSP5 STUDIO SW10 STUDIO

GENERAL

Type Biamp 2-way Powered Speaker Biamp 2-way Powered speaker Powered subwoofer

Crossover Frequency

2.5 kHz

LF: 30 dB/oct, HF: 30 dB/oct

2.5 kHz

LF: 24 dB/oct, HF: 24 dB/oct

—

Overall Frequency Response 45 Hz - 40 kHz (-10 dB) 50 Hz - 40 kHz (-10 dB) 25 Hz - 150 Hz (-10 dB)

Maximum Output Level 106 dB, 1 m on Axis 101 dB, 1 m on Axis 111 dB, 1 m on Axis

Demensions (W x H x D) 218 x 330 x 235 mm 179 x 279 x 208 mm 328 x 459 x 476 mm

Weight 12.2 kg 7.9 kg 26.5 kg

Magnetic Shielding Yes Yes Yes (None covered type)

SPEAKER SECTION

Components

LF 6.5" cone 5" cone

10" cone

HF 1.0" dome 1.0" dome

Enclosure

Type Bass-Reﬂex Bass-Reﬂex Bass-Reﬂex

Material PP PP MDF

AMPLIFIER SECTION

Output Power *

LF: 80 W

THD = 0.05 %, RL = 4

Ω

LF: 40W

THD = 0.02 %, RL = 4

Ω

180W

f = 100 Hz, THD = 1 %, RL = 8

Ω

HF: 50 W

THD = 0.05 %, RL = 6

Ω

HF: 27 W

THD = 0.02 %, RL = 6

Ω

S/N, IHF-A ﬁlter

≧

99 dB, LEVEL = Max

≧

94 dB, LEVEL = Max

≧

100 dB, LEVEL = Max

Input Sensitivity

XLR-3-31

+4 dBu, LEVEL = Center +4 dBu, LEVEL = Center +4 dBu, LEVEL = Center

-6dBu, LEVEL = Max -6 dBu, LEVEL = Max -6 dBu, LEVEL = Max

PHONE

— -10 dBu, LEVEL = Center —

— -20 dBu, LEVEL = Max —

Input Connectors, Impedance XLR-3-31 (balanced), 10 k

Ω

XLR-3-31 (balanced), 10 k

Ω

PHONE (unbalanced), 10 k

Ω

XLR-3-31 x 3 (balanced), 10 k

Ω

Output Connectors — —

XLR-3-32 x 3 (balanced),

Parallel connection with Input

Controls

LEVEL control

31 Positions Detent type VR

(Min = -

∞

Attenuation)

31 Positions Detent type VR

(Min = -

∞

Attenuation)

Center Click VR

(Min = -

∞

Attenuation)

LOW CUT switch

FLAT/

80 Hz (12 dB/oct)/

100 Hz (12 dB/oct)

—

HIGH TRIM +1.5/0/-1.5 dB at 15 kHz +1.5/0/-1.5 dB at 15 kHz —

LOW TRIM +1.5/0/-1.5/-3 dB at 45 Hz +1.5/0/-1.5/-3 dB at 60 Hz —

POWER switch on/off on/off on/off

PHASE switch — — Normal/Reverse

LPF control — — 40-120 Hz, 80 Hz at Center Click

Indicators LED

Green: Power On

Red: Clipping

Green: Power On

Red: Clipping

Green: Power On

Red: Clipping

Power Consumption 100 W 60 W 160 W

AC CORD

Length 2.5 m 2.5 m 2.5 m

English Deutsch Français Español

Dimensions

MSP5 STUDIO

SW10 STUDIO

MSP7 STUDIO

FrançaisEspañol EnglishDeutsch

MSP5 STUDIO

SW10 STUDIO

MSP7 STUDIO

MSP7 STUDIO MSP5 STUDIO SW10 STUDIO

-10

-20

-30

-40

-10

-20

-30

-40

-10

-20

-30

-40

Block Diagram

Performance graph

For details of products, please contact your nearest Yamaha represen-

tative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou

au distributeur le plus proche de vous ﬁgurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana

o el distribuidor autorizado que se lista debajo.

HEAD OFFICE

Yamaha Corporation, Pro Audio Division

Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2441

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de México S.A. de C.V.

Calz. Javier Rojo Gómez #1149,

Col. Guadalupe del Moral

C.P. 09300, México, D.F., México

Tel: 55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,

CEP 04534-013 Sao Paulo, SP. BRAZIL

Tel: 011-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.

Sucursal de Argentina

Olga Cossettini 1553, Piso 4 Norte

Madero Este-C1107CEK

Buenos Aires, Argentina

Tel: 011-4119-7000

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Tel: +507-269-5311

THE UNITED KINGDAM/IRELAND

Yamaha Music Europe GmbH (UK)

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

GERMANY

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH

Branch Switzerland in Zürich

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 044-387-8080

AUSTRIA/BULGARIA

Yamaha Music Europe GmbH Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

CZECH REPUBLIC/HUNGARY/

ROMANIA/SLOVAKIA/SLOVENIA

Yamaha Music Europe GmbH

Branch Austria (Central Eastern Europe Ofﬁce)

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-602039025

POLAND/LITHUANIA/LATVIA/ESTONIA

Yamaha Music Europe GmbH

Branch Sp.z o.o. Oddzial w Polsce

ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland

Tel: 022-500-2925

MARTA

Olimpus Music Ltd.

The Emporium, Level 3, St. Louis Street Msida

MSD06

Tel: 02133-2144

THE NETHERLANDS/

BELGIUM/LUXEMBOURG

Yamaha Music Europe Branch Benelux

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands

Tel: 0347-358 040

FRANCE

Yamaha Music Europe

BP 70-77312 Marne-la-Vallée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Music Europe GmbH, Branch Italy

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha Music Europe GmbH Ibérica, Sucursal

en España

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid), Spain

Tel: +34-902-39-8888

GREECE

Philippos Nakas S.A. The Music House

147 Skiathou Street, 112-55 Athens, Greece

Tel: 01-228 2160

SWEDEN/FINLAND/ICELAND

Yamaha Music Europe GmbH Germany ﬁlial

Scandinavia

J. A. Wettergrens Gata 1, Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

Yamaha Music Europe GmbH, Tyskland – ﬁlial

Denmark

Generatorvej 6A, DK-2730 Herlev, Denmark

Tel: 44 92 49 00

NORWAY

Yamaha Music Europe GmbH Germany -

Norwegian Branch

Grini Næringspark 1, N-1345 Østerås, Norway

Tel: 67 16 77 70

RUSSIA

Yamaha Music (Russia)

Room 37, bld. 7, Kievskaya street, Moscow,

121059, Russia

Tel: 495 626 5005

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

Yamaha Corporation,

Asia-Paciﬁc Sales & Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2303

TURKEY/CYPRUS

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Music Gulf FZE

LOB 16-513, P.O.Box 17328, Jubel Ali,

Dubai, United Arab Emirates

Tel: +971-4-881-5868

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,

Shanghai, China

Tel: 021-6247-2211

INDIA

Yamaha Music India Pvt. Ltd.

5F Ambience Corporate Tower Ambience Mall Complex

Ambience Island, NH-8, Gurgaon-122001, Haryana, India

Tel: 0124-466-5551

INDONESIA

PT. Yamaha Musik Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 021-520-2577

KOREA

Yamaha Music Korea Ltd.

8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,

Kangnam-Gu, Seoul, Korea

Tel: 02-3467-3300

MALAYSIA

Yamaha Music (Malaysia) Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

Petaling Jaya, Selangor, Malaysia

Tel: 03-78030900

SINGAPORE

Yamaha Music (Asia) Pte., Ltd.

#03-11 A-Z Building

140 Paya Lebor Road, Singapore 409015

Tel: 6747-4374

TAIWAN

Yamaha KHS Music Co., Ltd.

3F, #6, Sec.2, Nan Jing E. Rd. Taipei.

Taiwan 104, R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

4, 6, 15 and 16th ﬂoor, Siam Motors Building,

891/1 Rama 1 Road, Wangmai,

Pathumwan, Bangkok 10330, Thailand

Tel: 02-215-2622

OTHER ASIAN COUNTRIES

Yamaha Corporation,

Asia-Paciﬁc Sales & Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2303

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

Asia-Paciﬁc Sales & Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2303

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

PA29

Yamaha Pro Audio global web site http://www.yamahaproaudio.com/

Yamaha Manual Library http://www.yamaha.co.jp/manual/

C.S.G., Pro Audio Division

109 MW-02B0

Printed in China

Yamaha MSP7 STUDIO Le manuel du propriétaire

Marque: Yamaha

Modèle: MSP7 STUDIO

Catégorie: Haut-parleurs

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

italiano: Yamaha MSP7 STUDIO Manuale del proprietario
English: Yamaha MSP7 STUDIO Owner's manual
español: Yamaha MSP7 STUDIO El manual del propietario
Deutsch: Yamaha MSP7 STUDIO Bedienungsanleitung
русский: Yamaha MSP7 STUDIO Инструкция по применению
Nederlands: Yamaha MSP7 STUDIO de handleiding
português: Yamaha MSP7 STUDIO Manual do proprietário
dansk: Yamaha MSP7 STUDIO Brugervejledning
polski: Yamaha MSP7 STUDIO Instrukcja obsługi
čeština: Yamaha MSP7 STUDIO Návod k obsluze
svenska: Yamaha MSP7 STUDIO Bruksanvisning
Türkçe: Yamaha MSP7 STUDIO El kitabı
suomi: Yamaha MSP7 STUDIO Omistajan opas
română: Yamaha MSP7 STUDIO Manualul proprietarului

Documents connexes

Autres documents

Samson RESOLV SE8 Manuel utilisateur