Panasonic Super Dynamic III WV-CS950 Operating Instructions Manual

Printed in Japan

Gedruckt in Japan

Imprimé au Japon

Impreso en Japón

Stampato in Giappone

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

Model Nos. WV-CS950

WV-CS954E

Colour CCTV Camera

Operating Instructions

ENGLISH

DEUTSCH

FRANÇAIS

ESPAÑOL

ITALIANO

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

-2-

The serial number of this product may be found on the

top of the unit.

You should note the serial number of this unit in the

space provided and retain this book as a permanent

record of your purchase to aid identification in the event

of theft.

Model No. WV-CS950, CS954E

Serial No.

WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture.

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as

vases, shall be placed on the apparatus.

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT

CAREFULLY.

WARNING

THIS APPARATUS MUST BE EARTHED

IMPORTANT

The wires in this mains lead are coloured in accordance with the fol-

lowing code.

Green-and-yellow: Earth

Blue: Neutral

Brown: Live

As the colours of the wire in the mains lead of this appliance

may not correspond with the coloured markings identifying the ter-

minals in your plug, proceed as follows.

The wire which is coloured green-and-yellow must be connect-

ed to the terminal in the plug which is marked with the letter E or by

the earth symbol 1 or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the termi-

nal in the plug which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the ter-

minal in the plug which is marked with the letter L or coloured red.

The lightning flash with arrowhead

symbol, within an equilateral triangle,

is intended to alert the user to the

presence of uninsulated "dangerous

voltage" within the product's enclo-

sure that may be of sufficient magni-

tude to constitute a risk of electric

shock to persons.

The exclamation point within an equi-

lateral triangle is intended to alert the

user to the presence of important

operating and maintenance (servic-

ing) instructions in the literature

accompanying the appliance.

Turn the power off at the mains to

disconnect the main power for all

unit.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: An ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorporated

in the electrical installation of the building.

Wij verklaren als enige aansprakelijke, dat het product waarop

deze verklaring betrekking heeft, voldoet aan de volgende nor-

men of andere normatieve documenten, overeenkomstig de

bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC.

Vi erklærer os eneansvarlige for, at dette produkt, som denne

deklaration omhandler, er i overensstemmelse med standarder

eller andre normative dokumenter i følge bestemmelserne i

direktivene 73/23/EEC og 89/336/EEC.

Vi deklarerar härmed värt fulla ansvar för att den produkt till

vilken denna deklaration hänvisar är i överensstämmelse med

standarddokument, eller andra normativa dokument som

framställs i EEC-direktiv nr. 73/23 och 89/336.

Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä

ilmoitus koskee, noudattaa seuraavia standardeja tai muita

ohjeellisia asiakirjoja, jotka noudattavat direktiivien 73/23/EEC

ja 89/336/EE. säädöksiä.

Vi erklærer oss alene ansvarlige for at produktet som denne

erklæringen gjelder for, er i overensstemmelse med følgende

normer eller andre normgivende dokumenter som følger

bestemmelsene i direktivene 73/23/EEC og 89/336/EEC.

We declare under our sole responsibility that the product to

which this declaration relates is in conformity with the stan-

dards or other normative documents following the provisions of

Directives EEC/73/23 and EEC/89/336.

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

-3-

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Do not use near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or

the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the

points where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-overs.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged

in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been

dropped.

S3125A

ENGLISH

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

-4-

LIMITATION OF LIABILITY

THIS PUBLICATION IS PROVIDED “AS IS” WITHOUT

WARRANTY OF ANY KIND, EITHER EXPRESS OR

IMPLIED, INCLUDING BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY, FIT-

NESS FOR ANY PARTICULAR PURPOSE, OR NON-

INFRINGEMENT OF THE THIRD PARTY'S RIGHT.

IN NO EVENT SHALL MATSUSHITA ELECTRIC

INDUSTRIAL CO., LTD. BE LIABLE TO ANY PARTY OR

ANY PERSON, EXCEPT FOR REPLACEMENT OR

REASONABLE MAINTENANCE OF THE PRODUCT,

FOR THE CASES, INCLUDING BUT NOT LIMITED TO

BELOW:

(1) ANY DAMAGE AND LOSS, INCLUDING WITH-

OUT LIMITATION, DIRECT OR INDIRECT, SPE-

CIAL, CONSEQUENTIAL OR EXEMPLARY,

ARISING OUT OF OR RELATING TO THE

PRODUCT;

(2) PERSONAL INJURY OR ANY DAMAGE

CAUSED BY INAPPROPRIATE USE OR NEGLI-

GENT OPERATION OF THE USER;

(3) UNAUTHORIZED DISASSEMBLE, REPAIR OR

MODIFICATION OF THE PRODUCT BY THE

USER;

THIS PUBLICATION COULD INCLUDE TECHNICAL

INACCURACIES OR TYPOGRAPHICAL ERRORS.

CHANGES ARE ADDED TO THE INFORMATION

HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF

THIS PUBLICATION AND/OR THE CORRESPONDING

PRODUCT(S).

DISCLAIMER OF WARRANTY

(4) INCONVENIENCE OR ANY LOSS ARISING

WHEN IMAGES ARE NOT DISPLAYED, DUE TO

ANY REASON OR CAUSE INCLUDING ANY

FAILURE OR PROBLEM OF THE PRODUCT;

(5) ANY PROBLEM, CONSEQUENTIAL INCONVE-

NIENCE, OR LOSS OR DAMAGE, ARISING OUT

OF THE SYSTEM COMBINED BY THE DEVICES

OF THIRD PARTY.

(6) ANY CLAIM OR ACTION FOR DAMAGES,

BROUGHT BY ANY PERSON OR ORGANIZA-

TION BEING PHOTOGENIC SUBJECT, DUE TO

VIOLATION OF PRIVACY WITH THE RESULT OF

THAT SURVEILLANCE-CAMERA's PICTURE,

INCLUDING SAVED DATA, FOR SOME REA-

SON, BECOMES PUBLIC OR IS USED FOR THE

PURPOSE OTHER THAN SURVEILLANCE.

(7) ANY PROBLEM, CONSEQUENTIAL INCONVE-

NIENCE, ANY LOSS OR DAMAGE, ARISING

OUT OF THE IMPROPER DETECTION OR SLIP-

UP IN DETECTION BY VMD (Video Motion

Detector) FUNCTION OF THE PRODUCT.

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

-5-

This Colour CCTV Camera is a video surveillance

device that incorporates a 1/4-type {1/4"} CCD, a 30x

zoom lens, preset and pan and tilt capabilities in a

dome configuration. It also has the following features.

■ Super Dynamic

33

(SUPER-D

33

)

SUPER-D 3 makes it possible to capture clear images

of subjects whose illumination is extremely different

(page 22).

■ New DSP for High Sensitivity

A new noise reduction system lowers minimum illumi-

nance to 0.5 lux in the colour mode and 0.04 lux in the

black and white mode.

■ Auto Night time Switching to Black

and White Mode

The camera can be configured to switch to the black

and white mode automatically under low light condi-

tions for clear images, even at night.

■ Digital Flip

Normally, a camera needs to stop when it points

straight down during a tilt operation. With digital flip,

however, the camera is able to tilt from 0° to 180° in a

single motion. This makes it possible to track subjects

passing directly under the camera more smoothly.

■ Privacy Zone Function

The privacy zone function makes it possible to mask

specific areas of the scene from view.

■ Patrol Function

The patrol function remembers manual camera move-

ment routines for automatic playback when they are

needed. For example, you can teach the camera the

movements of the people you want to monitor, by

replaying the stored parameters complicated move-

ments are done automatically.

■ Camera Position Memory

The system can be configured with up to 256 camera

positions. A particular camera position can be selected

and viewed by entering the applicable preset number

on the system controller 10-key pad.

■ Motion Detection

The system can be configured so any motion on the

monitor screen during surveillance causes output of an

alarm signal.

This function can be used to structure a system with a

VTR that records images of night time intruders.

FEATURES

ACCESSORIES

Operating Instructions (this manual) . . . . . . . . . .1 pc. The following items are for installation.

Decorative Cover . . . . . . . . . . . . . . . . . . . . . . . . .1 pc.

Dust Protection Sheet . . . . . . . . . . . . . . . . . . . . . .1 pc.

8P Alarm Cable . . . . . . . . . . . . . . . . . . . . . . . . . . .1 pc.

4P Alarm Cable . . . . . . . . . . . . . . . . . . . . . . . . . . .1 pc.

Connector for 24 V AC (only for WV-CS954E) . . .1 pc.

Tilting

downwards

The picture is flipped

when the camera is

pointing straight down

(at around 135°).

Tilting upwards.

· · · Digital flip is performed only when the system controller joystick is held downwards.

Digital Flip Operation

OPTIONAL ACCESSORIES

Dome Cover(approx.50 % transparency,smoked type) . . . . . . .WV-CS3SE

Ceiling Mount Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .WV-Q105E/WV-Q116E/WV-Q117E

Wall Mount Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .WV-Q118E

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

PRECAUTIONS

1. Do not attempt to disassemble the camera.

To prevent electric shock, do not remove screws or

covers.

There are no user-serviceable parts inside.

Ask qualified service personnel for servicing.

2. Handle the camera with care.

Do not misuse the camera. Avoid striking, shaking,

etc. The camera could be damaged by improper

handling or storage.

3. Do not expose the camera to rain or moisture,

nor try to operate it in wet areas.

This product is designed for indoor use or locations

where it is protected from rain and moisture.

Turn the power off immediately and ask qualified

service personnel for servicing.

Moisture can damage the camera and also create

the danger of electric shock.

4. Do not use strong or abrasive detergents when

cleaning the camera body.

Use a dry cloth to clean the camera when it is dirty.

When the dirt is hard to remove, use a mild

detergent and wipe gently. Care should be taken

not to scratch the dome cover when wiping it.

Afterwards, wipe off the remaining detergent with a

dry cloth.

5. Never aim the camera at the sun.

Whether or not the camera is in use, never aim it at

the sun or other extremely bright objects.

Otherwise, blooming or smear may be caused.

6. Never aim the camera at strong light sources for

an extended period of time.

A light source such as a spot light causes burn-in

on the display screen. Failure to observe this may

cause the image to become discoloured due to

deterioration of the colour filter in the CCD.

7. Do not install this camera upside down.

This camera is designed for mounting on the ceiling

or wall. Using this camera installed upside down,

for example, mounted on the floor, may cause

malfunction.

8. Do not operate the camera beyond the specified

temperature, humidity or power source ratings.

Do not use the camera in an extreme environment

where high temperature or high humidity exists. Do

not place the camera near heat sources such as

radiators, stoves or other units that produce heat.

Use the camera under conditions where tempera-

ture is between –10 °C - +50 °C, preferably +40 °C

and humidity is below 90 %.

The input power source is 220 V - 240 V AC for WV-

CS950 and 24 V AC for WV-CS954E.

9. Do not install the camera near the air outlet of an

air conditioner.

The lens may become cloudy due to condensation

if the camera is used under the following

conditions.

• Rapid temperature fluctuations by switching the air

conditioner on and off.

• Rapid temperature fluctuations due to frequent door

opening and closing.

• Use in an environment where eyeglasses become

foggy.

• Use in a room filled with cigarette smoke or dust.

If the lens becomes cloudy due to condensation,

remove the dome cover and wipe all moist surfaces

with a soft cloth.

10.Consumables

Parts having contacts such as the lens-drive

motors, cooling fan motor and slip-rings inside the

camera are subject to wear with time. Please ask

the nearest service centre about replacement and

maintenance of such parts.

11.Do not aim the camera at the same object for a

long time.

Burn-in of an image may be caused on the

fluorescent screen of CRT.

12.Self-diagnosis Function

If the camera continues operating abnormally for 30

seconds or more due to such an accident as

external noise, the camera will automatically reset

its power. In the case it happens frequently, check

if there would be any environmental cause.

* Matsushita Electric Industrial Co., Ltd. herewith

declares that it will not be liable for any damage,

whether direct or indirect, caused by using the

product for business transaction or security, or

malfunctioning of this product.

-6-

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

-7-

OPERATING PRECAUTIONS

■ The camera does not have a power switch

Power turns on as soon as the power cord is plugged

into a power outlet. Before cleaning the camera,

unplug the power cord from the power outlet.

■ What to do if OVER HEAT appears on the display

This message indicates that the interior of the camera

has become very hot. Immediately unplug the power

cord from the power outlet, and contact a qualified

service person or system installer.

■ Note the following to ensure long-term trouble-

free operation

Long operation under high temperatures and high

humidity can cause components to deteriorate and

shorten camera life.

The recommended ambient operation temperature is

less than +35 °C.

Make sure the camera is installed in a location where it

is not directly exposed to heat from a radiator, heater,

etc.

■ Avoid use of this camera in a food preparation

area and other locations where there are large

amounts of steam vapour and oil.

■ About the Camera Cleaning Function

Prolonged use can lead to noise on the monitor and

divergence of preset positions.

If such conditions persist even after you perform

camera cleaning (page 35), use the special setup

menu to execute the “REFRESH” operation (page 39).

■ This camera is designed for use in a hanging

configuration only.

Do not use it in an upright configuration on a tabletop,

floor, etc. Such conditions create the risk of

malfunction.

■ CCD colour filter burn-in

Intense light concentrated on one spot for a long

period can cause deterioration of the CCD internal

colour filters, and discoloration of the affected part.

Even if the camera position is changed from a fixed

position, the discoloration at the previous location of

the concentrated light will remain on the screen.

■ Do not point the camera at a strong light source.

Intense light such as that produced by a spotlight

concentrated on one part of the screen can cause

blooming (rainbow around the strong light) or smearing

(vertical stripes above and below the strong light).

■ Do not aim the camera at the same object for a

long time.

Burn-in of an image may be caused on the fluorescent

screen of CRT.

■ Handle the camera carefully.

Do not drop the camera, or subject it to strong impact

or vibration. Such conditions create the risk of

malfunction.

■ Do not allow the camera to become wet.

Make sure that it is not exposed directly to water. Such

conditions create the risk of malfunction.

■ Condensation inside of the dome cover

Remove the dome cover and use a soft cloth to wipe

off the moisture (page 10).

■ Consumables

Parts having contacts such as the lens-drive motors,

cooling fan motor and slip-rings inside the camera are

subject to wear with time. Please ask the nearest

service centre about replacement and maintenance of

such parts.

■ Cleaning the camera

Turn off the camera and wipe it with a soft cloth. If the

camera is very dirty, wipe it off gently with a soft cloth

moistened with a weak solution of water and a neutral

kitchen detergent. Wring all excess liquid from the

cloth before wiping the camera. Next, wipe off all

remaining solution with a soft, dry cloth.

A dirty dome cover or lens causes deterioration of

picture quality. Use lens cleaning paper (like the type

available for cleaning eyeglasses or a camera lens) to

clean the lens.

The dome cover is particularly susceptible to damage.

Gently wipe it with a soft cloth.

Smearing

Bright Subject

Blooming

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

-8-

■ Downloading (saving) or uploading (recovering)

camera setting information

Camera setting information that can be downloaded to

the system controller etc, includes existing preset

position settings and menu settings. However, the

following items are not included.

• Patrol function (page 32)

• Area title function (page 34)

• Blemish compensation pattern (page 39)

• RS485 settings (page 20)

• Password settings (page 42)

Be sure the camera is not moving and aimed at

something that moves very little (like a wall) before

downloading camera preset data to the system

controller etc. or uploading downloaded data to the

camera.

Uploading of WV-CS950 series preset data to other

models (e.g. WV-CS850 series, WV-CS850A series,

WV-CS850B series and WV-NS320 series) may cause

an error and failure of the uploading process.

■ Self-diagnosing Function

If abnormal operation due to external noise or some

other reason continues for more than 30 seconds, the

camera will automatically reset itself and restore

normal operation. Reset operation the same

initialisation routine that is performed when the camera

is turned on. If the reset is required too often, it could

mean that the camera is installed in a location where

there is a large amount of external noise. This can

cause malfunction of the camera, so you should

contact a qualified service person or system installer

as soon as possible.

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

-9-

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

LIMITATION OF LIABILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

DISCLAIMER OF WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

■ Super Dynamic 3 (SUPER-D 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

■ New DSP for High Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

■ Auto Nighttime Switching to Black and White Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

■ Digital Flip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

■ Privacy Zone Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

■ Patrol Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

■ Camera Position Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

■ Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

ACCESORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

OPTIONAL ACCESORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

OPERATING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

CONSTRUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

INSTALLATION PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

DIP SWITCH SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

■ Communication Parameters (DIP Switch 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

■ Unit Number (DIP Switch 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

■ RS485 Communication Parameters (DIP Switch 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

CAMERA INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

■ Preparing the Camera and Decorative Cover for Side Cable Exit . . . . . . . . . . . . . . . . .15

■ Installing the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

UNINSTALLING THE CAMERA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

■ Removing the Decorative Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

■ Uninstalling the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

RS485 SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

USING THE SETUP MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

■ Displaying the Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

■ Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

CAMERA SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

■ Using the Camera Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

PAN/TILT SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

■ Using the Pan/Tilt Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

ALARM SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

■ Using the Alarm Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

SPECIAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

■ Using the Special Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

SCENE SELECT SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

■ Using the Scene Select Setting Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

QUICK MENU SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

■ Displaying the Quick Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

PASSWORD SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

■ Password Lock Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

SHORTCUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

CONSTRUCTION

Ensuring Trouble-free Operation

• This camera uses a “slip ring” for transmission of electrical power and signals. A dirty slip ring can cause

deterioration of picture quality during panning and generation of noise.

In order to ensure trouble-free camera operation, make sure that the cleaning function (page 35) is turned on.

• If cleaning the slip ring does not eliminate poor picture quality and noise, it could mean that the slip ring has

reached the end of its service life. Contact a qualified service person or system installer to have it replaced.

-10-

Power Connector for WV-CS954E

Power Connector for WV-CS950

Video Output Connector

Decorative Cover (provided)

Dome Fix Ring

Safety Wire

Lens

The lens cannot be replaced.

Data Port

Alarm Output Connector

Alarm Input Connector

Camera Mounting Base

Dome Cover

Remove the camera first before removing the

dome cover (page 17).

Rotate the dome fix ring to the left to remove it.

Tighten the dome fix ring securely to prevent it from

coming loose. Securely anchor the camera when

removing the dome cover.

The dome cover is easily damaged,

and should be handled with care.

Camera

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

INSTALLATION PRECAUTIONS

Warning: Discuss the installation location for the

camera with your retailer, and select a place that is

strong enough for the installation. If you install the

camera on a ceiling or wall, except for accidents

caused by fault in the camera, Panasonic holds

absolutely no responsibility for accidents caused by

the camera falling due to unsuitable installation.

Take sufficient care when installing the camera. If

the installation is not strong enough, be sure to

sufficiently reinforce the location and check that it is

safe.

Warning: Always request installation work from a

qualified service person or system installer. Lack of

technical knowledge creates the risk of fire, electric

shock, personal injury, and material damage.

■ Camera Installation Location

• Install the camera on a ceiling (concrete, etc.) at a

location that is sufficiently strong to support it.

• When installing the camera on a ceiling of

insufficient strength (like a drop ceiling), use the

optionally available WV-Q105E Direct Attachment

Ceiling Mounting Bracket or the WV-Q116E

Embedded Ceiling Mount Bracket.

• For ceiling mounting, use the optionally available

WV-Q117E Ceiling Mount Bracket.

• For wall mounting, use the optionally available WV-

Q118E Wall Mount Bracket.

■ This camera is an indoor camera. It is not

designed for outdoor use.

■ This camera is designed for use in a hanging con-

figuration only. Using it in an upright or inclined

configuration can cause malfunction and shorten

the life of the camera.

■ Install the camera in a horizontal configuration,

with the dome pointed downwards.

■ Never install or use the camera in the following

locations.

• Areas directly exposed to rain and water

• Near a swimming pool or other areas where

chemicals are used

• Food preparation areas and other locations where

there are large amounts of steam vapour and oil, in

flammable atmospheres, other special environments

• Areas where radiation, X-rays, strong electric

waves, or magnetism is generated

• At sea, in coastal areas, or in areas where corrosive

gas is being generated

• Areas outside of the allowable ambient operating

temperature range (-10 °C to +50 °C)

• In a motor vehicle, on a boat, or other areas subject

to strong vibration (This camera is not designed for

use in a vehicle.)

• Near an air conditioner outlet, near a door that opens

up to the outdoors, or any other area subjected to

temperature extremes (Such conditions can cause

clouding and condensation formation on the dome

cover.)

■ When wiring the camera, its cables (power, video

output, RS485, alarm in, alarm out) can exit out

the side or the top of the camera.

• When using the top cable exit configuration, drill a

hole in the ceiling to allow passage of the cables.

(See step 3 on page 15.)

• When using the side cable exit configuration,

prepare the cut-out in the die cast case and

decorative cover. (See “Preparing the Camera and

Decorative Cover for Side Cable Exit” on page 15.)

■ Noise interference considerations

When using a power line that is greater than 240 V AC

and wiring that is longer than 1 meter, wiring should be

performed using a separate metal conduit. (The metal

conduit must be earth grounded.)

■ Screws should be ordered separately.

The camera does not come with screws. Make sure

that the materials and structure of the installation

location is strong enough to support the total weight of

the camera.

Important:

• Before setting up the camera for a configuration

where the camera's RS485 data port is used for

camera control (pan, tilt, etc.) by the system

controller, the camera's DIP switches must be

configured to specify the unit number and

communication parameters. (page 12)

If DIP switch setting is not performed, the

system controller control will not be possible

and camera setup will have to be performed

again. Be sure to check the DIP switch settings

before setting up the camera.

-11-

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

-12-

Notes:

• If you need to connect a ground, be sure to do it

before you connect the main power plug. Also,

when removing the ground, be sure to disconnect

the main power plug.

• The camera does not have a power switch, so it

turns on as soon as the power cord is plugged into

a power outlet. A self-cleaning function is activated

(PAN/TILT/ZOOM/FOCUS) when the camera is

turned on.

■ Heat radiation

The surface of the camera radiates heat. Ventilation

holes should be provided when installing the camera in

an enclosed ceiling or confined location where heat

can build up.

■ Beware of high humidity.

If the camera is installed when humidity is very high,

moisture may collect in the camera and cause the

dome to become foggy. If the dome becomes foggy,

remove it when the humidity is low and eliminate the

moisture inside the camera, and then replace the

dome. (page 7, 10)

DIP SWITCH SETTINGS

In a configuration where the camera's RS485 data port is used for camera control (pan, tilt, etc.) by the system

controller, the camera's DIP switches must be configured to specify the unit number and communication parameters.

The camera mounting base needs to be removed to access the DIP switches. See steps 1 and 2 on page 15 for

information about how to remove the camera mounting base.

1234

ON

1234

ON

5678

DIP Switch 1 DIP Switch 2

■ Communication Parameters (DIP Switch 2)

The factory default settings of these DIP switches are all OFF.

Switch 1: Terminator (Internal Termination Resistance)

Set it to ON in the following situations.

• When only one camera is connected.

• When only one camera is connected via a daisy chain over a long

distance.

Switches 2 through 4: Communication Parameters

This setting toggles between 2-line and 4-line communication.

Use these switches to select the communication protocol

being used.

1234

ON

Terminator

Communication

Parameters

1234

ON

4-line Communication

1234

ON

2-line Communication

Ventilation holes

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

-13-

■ Unit Number (DIP Switch 1)

The factory default settings of these DIP switches are all OFF. (Coaxial Multiplex System)

1234

ON

5678

DIP Switch 1

Unit

Number

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

DIP Switch 1

Unit

Number

DIP Switch 1

Unit

Number

1 ~ 96 *

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

56 8

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

56 8

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

7

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

-14-

* When using the Unit Number 1 to 96 setting, the unit number setting needs to be configured using the RS485 SET UP menu. For details

about configuring this setting, see step 2 and page 20.

* Turning on power when this setting is selected causes the RS485 SET UP menu to appear during the initialisation routine.

1234

ON

5678

DIP Switch 1

Unit

Number

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

DIP Switch 1

Unit

Number

DIP Switch 1

Unit

Number

69

70

71

72

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

5678

1234

ON

567

8

■ RS485 Communication Parameters (DIP Switch 1)

Configuring DIP Switch 1 as shown below resets communication parameters to their factory default settings. You can

then change the settings as desired.

1234

ON

5678

DIP Switch 1 Setting Description

1234

ON

5678

1234

ON

5678

1234

ON

5678

This setting resets communication parameters to the factory default settings.

BAUD RATE : 19 200 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit

BAUD RATE : 9 600 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit

BAUD RATE : 4 800 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit

ON

Perform the following steps to use this setting.

(1) Turn off the camera and use DIP Switch 1 to configure RS485 communication parameters as shown above.

(2) Turn on the camera.

This applies the setting you configured in step (1).

(3) Turn off the camera, use DIP Switch 1 to set the unit number (pages 13 and 14), and then turn the camera

back on again.

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

CAMERA INSTALLATION

■ Preparing the Camera and

Decorative Cover for Side Cable

Exit

The camera and decorative cover should be prepared

as shown below when mounting the camera on a

ceiling or wall with its cables (power, video output,

RS485, alarm in, alarm out) exiting from the side.

The camera mounting base needs to be removed in

order to prepare the camera. See steps 1 and 2 below

for information about how to remove the camera

mounting base.

* Prevent the dome cover from being scratched by

placing it on a soft cloth while you are working.

■ Installing the Camera

• Select an installation location that is strong enough

to withstand the total weight of the camera.

Installing the camera at a location that is too weak

can cause it to fall.

• Remove the protective sheet after the installation

work is complete.

• If you are using an optional bracket to install the

camera, install the bracket in accordance with the

instructions that come with it.

1. Remove the fixing screw (M3 × 6) that secures the

camera to the camera mounting base.

Put the screw in a place where it will not become

lost.

2. Rotate the camera mounting base unit in the

direction indicated by the arrow and remove it.

3. Using the camera mounting base as a template,

mark the locations of the four mounting holes on the

ceiling.

If you are using the top cable exit configuration,

mark the location of the cable hole on the ceiling

and drill the hole.

4. Affix the camera mounting base onto the ceiling.

Use screws (M4) at the locations you marked above

to secure the camera mounting base to the ceiling.

If you do not plan to install the camera right away,

affix the dust protection sheet that comes with the

camera to the camera mounting base to keep dust

off of it.

-15-

Break it off

with a pair of

pliers.

Cut it off

with a

razor knife.

Preparing the Camera Die Cast Case*

Preparing the Decorative Cover

After loosening

the screw, press

upwards on the

camera and then

remove it.

Fixing screw

Rotate

Pull the camera

mounting base

up to remove it.

15°

Mark here

Screws

(M4, available separately)

Dust Protection Sheet

(comes with camera)

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

5. Attach the safety wire for securing the camera to

the camera mounting base.

Pull on the safety wire to make sure its ring is

securely connected to the camera mounting base

hook.

If the dust protection sheet that comes with the

camera is affixed to the camera mounting base,

remove it before performing the above step.

Note: The safety wire is designed to allow the

camera to hang from it. Do not apply force greater

than the weight of the camera to the wire.

6. Install the camera onto the camera mounting base.

Aligning with the camera mounting base, press

down on the camera as far as it will go and rotate in

the direction indicated by the arrow.

7. Use the fixing screw you removed in step 1 to

secure the camera to the camera mounting base.

8. Check the installation.

• Is the camera is level and installed securely?

• Is the camera free of looseness?

• Does the fixed part of the camera remain in place

when you try to rotate it?

9. Separate the two parts of the decorative cover

(comes with camera).

Press upwards on the decorative cover at the

points marked (indicated by the arrows, in the

illustration below) to unhook the two parts from

each other.

* When removing the decorative cover, the direction

to press ( ) is shown on the side of the decorative

cover.

Caution: Pressing up on the wrong side of the

decorative cover can damage it.

10.Put the two pieces of the decorative cover on the

left and right side of the camera, and hook them

together.

Align the hooks and press the piece indicated by

the arrow in the illustration below into the other

piece.

11.Slide the decorative cover up to the ceiling.

• In the case of a top cable exit configuration, slide

the decorative cover straight up and press it firmly

against the ceiling.

• In the case of a side cable exit configuration, align

the cut-out in the decorative cover with the cables

as you slide it up, and press it firmly against the

ceiling.

➡

-16-

Safety

wire ring

Camera

Mounting

Base

Rotate

15°

Unhook

Back

Fix securely

Press

Fix securely

Press

Hold

securely

Back

Hold

securely

Align

hook

Press

Top Cable Exit

Configuration

Side Cable Exit

Configuration

Align with

cut-out

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

UNINSTALLING THE CAMERA

Caution: Make sure you perform the steps below

carefully and exactly when uninstalling the camera

and decorative cover. Failure to do so creates the

risk of damage to the camera.

■ Removing the Decorative Cover

Note that you need to separate the two parts of the

decorative cover in order to remove it.

1. Unhook the two parts of the decorative cover.

Press upwards on the decorative cover at the

points marked (indicated by the arrows, in the

illustration below) to unhook the two parts from

each other.

* When removing the decorative cover, the direction

to press ( ) is shown on the side of the decorative

cover.

■ Uninstalling the Camera

The camera and its base unit are secured by screws.

This configuration provides double anchoring, and you

should use the following procedure to uninstall the

camera.

1. Remove the fixing screw that secures the camera to

the camera mounting base.

Put the screw in a place where it will not become

lost.

2. Remove the camera from the camera mounting

base.

Rotate the camera in the direction indicated by the

arrow and remove it.

➡

-17-

Unhook

Back

Fix securely

Press

Fix securely

Press

3. Remove the safety wire from the camera mounting

base.

Camera

Mounting

Base

Fixing screw

Rotate

15°

After loosening

the screw, press

upwards on the

camera and then

remove it.

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

Pin no. Power source

1

2

3

4

24 V AC LIVE

24 V AC NEUTRAL

Ground

Not use

CONNECTIONS

-18-

RS485 Data Port

Alarm Input Connector

Alarm Output Connector

T(B)

T(A)

R(B)

R(A)

Red

Orange

Yellow

Green

Data

Tx

Data

Rx

(RJ-12)

Alarm In 2 (Red)

Alarm In 1 (Black)

GND (Brown)

Alarm In 3 (Yellow)

Alarm In 4 (Blue)

GND (Orange)

GND (

Light Blue or Green

)

GND (Violet)

Alarm Out 2 (Pink)

Alarm Out 1 (Grey)

GND (White)

GND (Light Green

or Light Blue)

Coaxial Cable (5C-2V)*2

220 V - 240 V AC

(WV-CS950)

24 V AC Cable for camera

RS485 Data Port

To VIDEO IN port

(CAMERA IN)

8P Alarm Cable (provided)

PP Alarm Cable (provided)

To sensor, etc.

To buzzer,

display device, etc.

To Matrix Switcher,

etc.

Video Output

Connector

Alarm Input

Connector

Alarm Output

Connector

Twisted Pair Cable*1

(BNC)

(RJ-12)

24 V AC (WV-CS954E)

*1: For twisted pair cable, use shielded low-impedance cable with a thickness of at least AWG#22

(0.33 mm

2

).

*2: Keep the overall length of coaxial cable under 1200 meters (in the case of 5C-2V).

*3: Be sure to connect the grounding cable to ground.

Alarm In/Out Ratings

Alarm In : 5 V DC pull-up input. Drive capacity of at

lease 0.2 mA required.

OFF : 4 V DC minimum 5 V DC maximum,

or open

ON : 1 V DC maximum or short

Alarm Out : Open collector output. 16 V DC, 100 mA

maximum drive capacity

OFF : Open

ON : 100 mA maximum

* When connecting to an external device, set up the

system so the ratings are not exceeded.

Note: Do not turn off camera power within 30 seconds

after turning it on. Doing so can cause pan, tilt, zoom,

or focus to go out of position.

Precautions

• The following connections should be made by qualified service personnel or system installers in accordance

with all local codes.

• See the reverse side of the cover page for main lead connection.

#24

(0.22mm

2

)

Copper wire size

(AWG)

Length

of cable

(approx.)

(m)

(ft)

#22

(0.33mm

2

)

#20

(0.52mm

2

)

#18

(0.83mm

2

)

20 30 45 75

65 100 160 260

• 24 V AC Power Supply Connection

Recommended wire gauge sizes for 24 V AC line

Accessory Connector Information

1

3

2

4

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

-19-

Contact

Insert

Up

A

Approx.

3 mm (0.1 inch)

Insert the wire until A position

and clamp the contacts.

Wire

Up

Contact

Wire

Approx. 3 mm

Insert the wire until A position

and clamp the contacts.

Contact

Up

Wire

How to Assemble the Cable with the Accessory

Connector

Strip back the cable jacket approx. 3 mm and separate

the individual conductors.

Prepare the individual conductors for clamping. Use

MOLEX band tool part number 57027-5000 (for UL-

Style Cable UL1015) or 57026-5000 (for UL-Style

UL1007) for clamping the contacts.

After clamping the contacts, push them into the proper

holes in the accessory connector of this camera until

they snap in place.

Cautions:

• Shrinking the cable-entry seal is a one-time

procedure. Do not shrink the cable-entry seal until

ascertaining that the unit is functioning.

• CONNECT THIS TO 24 V AC CLASS 2 POWER

SUPPLY ONLY.

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

RS485 SETUP

Use the following procedure to configure the RS485

setup when you want to use the system controller to

control the camera (pan, tilt, etc.) via the camera's data

port.

1. Display the setup menu (page 21), move the cursor

to COMMUNICATION O, and then press the CAM

(SET) button.

This will display the RS485 setup menu.

2. Check the unit number. (page 13)

The UNIT NUMBER item shows the unit number

specified by DIP Switch 1. The factory default unit

number is 1.

If DIP Switch 1 specifies 1 to 96 as the unit number,

move the cursor to UNIT NUMBER and then tilt the

joystick left or right to select a unit number (1 to 96).

Note: It is not necessary to configure the RS485

SET UP menu SUB ADDRESS setting.

3. Move the cursor to BAUD RATE, and then tilt the

joystick left or right to select a baud rate setting.

Tilting the joystick cycles through the baud rate

(transmission speed) display in the sequence

shown below. (unit: bits/s) The factory default

setting is 19200.

4. Move the cursor to DATA BIT, and then tilt the

joystick left or right to select a data bit setting (7 or

8).

The factory default setting is 8.

5. Move the cursor to PARITY CHECK, and then tilt the

joystick left or right to select a parity bit setting

(NONE, ODD, EVEN).

The factory default setting is NONE.

6. Move the cursor to STOP BIT, and then tilt the

joystick left or right to select a stop bit setting (1 or

2).

The factory default setting is 1.

7. Move the cursor to XON/XOFF, and then tilt the

joystick left or right to select an XON/XOFF setting.

The factory default setting is NOT USE.

NOT USE: Disables X ON/X OFF data flow control.

USE : Enables X ON/X OFF data flow control.

8. Move the cursor to WAIT TIME, and then tilt the

joystick left or right to select a wait time setting.

The wait time is the time that the camera should

wait before resending data when no receive

acknowledgement (ACK) is returned after data is

sent.

Tilting the joystick cycles through the wait time

display in the sequence shown below. (unit: ms)

The factory default setting is OFF.

9. Move the cursor to ALARM DATA, and then tilt the

joystick left or right to select an alarm data send

mode setting.

POLLING : Sends alarm data in response to a

request by the system controller.

AUTO1 : Sends alarm data each time an alarm

signal is input.

AUTO2 : Sends alarm data at five-second intervals.

This is the factory default setting.

10.Move the cursor to DELAY TIME, and then tilt the

joystick left or right to select a delay time setting.

The delay time is the time is the time the camera

should wait before sending a receive acknowledge

(ACK). The delay time display changes in the

sequence shown below. (unit: ms) The factory

default setting is OFF.

This setting can be configured only when 2-line

configuration is selected by DIP Switch 2. (page 12)

-20-

** RS485 SETUP **

UNIT NUMBER

SUB ADDRESS

BAUD RATE

DATA BIT

PARITY CHECK

STOP BIT

XON/XOFF

WAIT TIME

ALARM DATA

DELAY TIME

RET TOP

1

-----

19200

8

NONE

1

NOT USE

OFF

AUTO2

OFF

2400 4800 9600 19200

OFF ↔ 100MS ↔ 200MS ↔ 400MS ↔ 1000MS

OFF ↔ 100MS

www.absolualarme.com met à la disposition du public, via www.docalarme.com, de la documentation technique dont les références, marques et logos, sont la propriété des détenteurs respectifs

La page charge ...

Panasonic Super Dynamic III WV-CS950 Operating Instructions Manual

Ce manuel convient également à

Panasonic Super Dynamic III WV-CS950 Operating Instructions Manual

dans d''autres langues

Documents connexes

Autres documents