Orbit 24511 Guide d'installation

Marque: Orbit

Modèle: 24511

Catégorie: Minuteries électriques

Taper: Guide d'installation

QUICK START GUIDE

B-HYVE XD BLUETOOTH®

HOSE FAUCET TIMER

FAUCET

CONNECTION

OUTLET

RAINDELAYICON

FILTER

DIAL

LOW

BATTERY

INDICATOR

BLUETOOTH®

ICON

Write down the MAC address: 12 digit alphanumeric

code located on the bottom of the timer.

Timer MAC Address: __ __ :__ __ :__ __ :__ __ :__ __ :__ __

Installing the Batteries

Insert two AA (1.5V) alkaline batteries (not included) and

replace the tray.

Replace batteries when low battery icon appears

on display.

Used up or dead batteries must be removed

from the timer and disposed of properly. Do not

dispose of batteries in fire. Batteries may explode

or leak. Remove batteries when storing timer.

Note: Firmly replace the battery tray to ensure water

resistance and increase battery life. You will know the

battery tray is fully inserted if it does not pull out easily.

Open the B-hyve® App

Log into your B-hyve account and tap “My B-hyve”. Go

to “devices” then “add device”. Select B-hyve XD. The

app will walk you through the rest of the process.

For new users, search apps for “B-hyve” and

download the free Android or iOS app. Create an

account to begin setup.

The Bluetooth® icon on the display should be

flashing indicating the timer is in pairing mode.

If Bluetooth® icon is not flashing, or at any time

you need to re-pair or do a factory reset, turn the

dial so the arrow is pointing to OFF, press and

hold the dial for 5 seconds.

Note: Your display will show lock icon when using

advanced scheduling only found in the B-hyve app.

While watering is in progress, the dial at the

timer will deactivate and will not scroll until the

current watering cycle is finished. To stop active

watering press the dial.

Note: When the display shows a full screen of symbols

release the dial. The display will show 12:00 pm in the

AUTO/MANUAL mode verifying the reset has been

completed. Resetting the timer will erase all programs

and it will need to be reprogrammed to your desired

watering schedule.

PROGRAMMING THE TIMER

AT THE FAUCET

PROGRAMMING THE TIMER

WITH BLUETOOTH®

Set Clock

1. Turn the dial so the arrow is pointing to SET CLOCK.

2. Press the dial to confirm the selection, the hour will

begin to flash.

3. Turn the dial until the current hour is displayed

including the correct AM or PM, then press the dial to

confirm the selection. The minutes will begin to flash

indicating the next step in the process.

4. Turn the dial until the current minutes are displayed,

then press the dial to confirm the selection.

Start Time

1. Turn the dial so the arrow is pointing to START TIME.

2. Press the dial to confirm the selection, the time slot

will begin to flash.

3. Turn the dial until the desired start time hour is

displayed including the correct AM or PM, then press the

dial to confirm the selection. The minutes will begin to

flash, indicating the next step in the process.

4. Turn the dial until the desired minutes are displayed,

then press the dial to confirm the selection.

How Often

1. Turn the dial so the arrow is pointing to HOW OFTEN.

2. Press the dial to confirm the selection, the number slot

will begin to flash.

3. Turn the dial until the desired interval is displayed,

then press the dial to confirm the selection.

Note: 1 day is every day, 2 days is every other day, etc.

Auto Mode

1. Turn the dial so the arrow is pointing to

AUTO/MANUAL.

2. Press the dial to confirm the selection, the arrow will

stop flashing and you are now in AUTO mode.

How Long

1. Turn the dial so the arrow is pointing to HOW LONG.

2. Press the dial to confirm the selection, the time slot

will begin to flash.

3. Turn the dial until the desired number of minutes are

displayed. Press the dial to confirm the selection.

more information on back

Printers are responsible

for meeting print

production requirements.

Any changes must be

approved by Orbit®.

Printed piece must meet

designated specifications

on this form.

This work is the property

of Orbit®, and cannot

be used, reproduced or

distributed in any way

without their express

permission.

Dieline

PMS

0000

Fold

PMS

0000

Product

Coverage

PMS

0000

Dims./

Callout

PMS

0000

∙

Orbit®

1.801.299.5555

orbitonline.com KGlue

Folded Flat Additional Information

PRIN TERS ARE

REQUIRED TO MATCH

ALL SP ECIFIED

PMS COLORS.

DATE: 03/29/2021

DESIGNER: NK MARKETING: CD

SOFTWARE: Adobe Indesign CC

ARTWORK №: 24511-24 rC L:

_._" W:

3.75"

2.75"

18.75"

5.50"

Rain Delay

Rain delay allows you to postpone your watering

schedule for a set period of time. To access the rain

delay feature at the timer, follow the steps below.

1. With the timer in the AUTO mode, press and hold

the dial for 3 seconds.

2. The rain delay icon will appear and the number slot

will begin to flash.

3. Turn the dial until the desired amount of time to

delay watering is displayed, then press the dial to

confirm the selection.

4. The display will flash between the current time and

how long until the rain delay ends.

FCC Statement: FCC ID: ML6-HT31BT

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause

undesired operation.

FCC Warning: Any changes or modifications not expressly approved by

the party responsible for compliance could void the user’s authority to

operate this equipment.

Note: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device meets the FCC and IC requirements for RF exposure in

public or controlled environments. The end user is advised to maintain a

distance 20 cm from the timer and any personnel to ensure compliance

with RF exposure regulations.

IC Statement: IC: 3330A-HT31BT

This device complies with Industry Canada license exempt RSS

standard(s). Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired

operation. This Class B digital apparatus complies with Canadian ICES-

003.

Remarque: cet appareil été testé et déclaré conforme aux limites

d’exposition pour les appareils numériques de classe B, selon la section

15 de la Règlementation de la FCC. Ces limites sont conçus pour fournir

une protection raisonnable contre les interférences nuisibles dans une

installation résidentielle. Cet appareil produit, utilise et peut émettre

de l’énergie radio fréquence et, si elle n’est pas installée et utilisée

conformément aux instructions, peut causer des interférences nuisibles

aux communications radio. Cependant, il n’est pas garantie que des

interférences ne se produisent pas dans une installation particulière. Si cet

appareil cause des interférences gênantes à la réception d’un signal radio

ou de télévision, ce qui peut être déterminé en allumant et en éteignant

l’appareil, l’utilisateur peut corriger les interférences en suivants une des

mesures suivantes :

• Réorientez ou repositionnez l’antenne de réception.

• Augmentez la distance entre l’appareil et le récepteur.

• Branchez l’appareil dans une prise sur un circuit différent du circuit

sur lequel le récepteur est branché.

• Consulter le revendeur ou un technicien radio/TV expérimenté

pour obtenirde l’aide.

Cet appareil est conforme aux exigences de la FCC et de l’IC

concernant l’exposition aux ondes dans un environnement public ou

contrôlé. Il est conseillé à l’utilisateur final de maintenir une distance

de 20 cm du contrôleur pour assurer la conformité aux réglementations

d’exposition RF.

Information de conformité pour le Canada Déclaration de l’IC :

Cet appareil est conforme à la norme RSS d’Industry Canada. Son

fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil

ne doit pas causer d’interférences nuisibles, et (2) cet appareil doit

tolérer toutes les interférences, dont les interférences pouvant causer

un fonctionnementnon désiré. Cet appareil numérique de classe B est

conforme à la norme canadienneICES-003.

PN 24511-24 rC

Need Help?

If you encounter a problem, please

B-hyve to the store.

Scan the QR Code to access the

help page online.

call us

1-800-488-6156

ADDITIONAL FEATURES

Manual/Hand Watering

This feature allows you to water without interrupting

your programmed watering schedule. To access this

feature, follow the steps below.

1. With the timer in AUTO mode, press the dial once

quickly to access the MANUAL feature.

2. Manual will appear on the display and the time slot

will begin to flash.

3. Turn the dial until the desired number of minutes are

displayed, then press the dial to confirm selection.

4. The watering icon will appear on the display and the

display will begin to flash between the current time and

the remaining manual watering minutes.

Note: There may be a slight delay between the time the

dial is pressed and when manual watering begins.

Timer

Range: 150 ft without interference

Pressure Operating Range: 10-100 PSI

Temperature Operating Range:

35°F-122°F (2-50°C)

For Outdoor Use With Cold Water Only

Not For Use With Appliances

To stop manual watering, press the dial. The

watering icon will disappear and your timer will

resume its programmed watering schedule.

If the manual watering feature will overlap a

programmed watering scheduled, the timer will

delay that program until the manual watering

feature is done.

To remove a rain delay, press and hold the

dial for 3 seconds. The rain delay icon

will turn off and your timer will resume its

programmed watering schedule. Purchase the B-hyve Wi-Fi Hub

online or at your local retailer

PN # 21027

You are here

A B-hyve Wi-Fi Hub connection

gives you control from anywhere

Congratulations!

Your timer is now programmed. The display will flash

between the current time and how long until the next

start time.

Orbit 24511 Guide d'installation

Marque: Orbit

Modèle: 24511

Catégorie: Minuteries électriques

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Orbit 24511 Installation guide

Documents connexes

Autres documents

B-hyve b-hyve 57985 XR Smart Indoor-Outdoor Sprinkler Timer Mode d'emploi