Jenn-Air JXW9030WP Le manuel du propriétaire

Marque: Jenn-Air

Modèle: JXW9030WP

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

. I II

IENNAII_ 30', 36, AND 48"(76.2CM, 91.4CM,

AND 121.9CM) COMMERCIALSTYLEWALL-MOUNT

CANOPY RANGEHOOD

HOTIEDECUISINIEREJENN-AII_ POURMONTAGE

M ' 36"ET48" ,

URAL_, (76,2 CM 91,4 CM

ET121,9CM)

InstallationInstructionsand Use&Care Guide

For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-807-6777, or visit our website at www.jennair.ca.

Instructionsd'installationetGuide d'utilisationetd'entretien

Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web & www.jennair.ca.

Table of Contents/Table des matieres ................... 2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISATION RI_SIDENTIELLE UNIQUEMENT.

JENN-AIRo

LI3U NA/W10274316A

TABLEOF CONTENTS

RANGE HOOD SAFETY ................................................................. 3

INSTALLATION REQUIREMENTS ................................................ 5

Tools and Parts ............................................................................ 5

Location Requirements ................................................................ 5

Venting Requirements .................................................................. 6

Electrical Requirements ............................................................... 7

INSTALLATION INSTRUCTIONS .................................................. 8

Prepare Location .......................................................................... 8

Install Range Hood ....................................................................... 9

Install Range Hood Blower Motor ................................................ 9

Make Electrical Connection ....................................................... 10

Complete Installation and Check Operation .............................. 11

RANGE HOOD USE ...................................................................... 11

Range Hood Controls ................................................................ 11

RANGE HOOD CARE ................................................................... 12

Range Hood Lamps ................................................................... 12

Cleaning ...................................................................................... 12

WIRING DIAGRAMS ..................................................................... 13

ASSISTANCE OR SERVICE ......................................................... 15

WAR RANTY .................................................................................. 16

TABLEDESMATIERES

SI_CURITI_ DE LA HOTTE DE CUlSINII_RE ............................... 17

EXIGENCES D'INSTALLATION ................................................... 19

Outillage et pieces ...................................................................... 19

Exigences d'emplacement ......................................................... 19

Exigences concernant I'evacuation ........................................... 20

Specifications electriques .......................................................... 22

INSTRUCTIONS D'INSTALLATION ............................................. 22

Preparation de I'emplacement ................................................... 22

Installation de la hotte ................................................................ 23

Installation du moteur du ventilateur de lahotte ....................... 23

Raccordement electrique ........................................................... 24

Achever I'installation et verifier le fonctionnement .................... 25

UTILISATION DE LA Ho'n'E ....................................................... 25

Commandes de lahotte de cuisiniere ....................................... 25

ENTRETIEN DE LA HOTTE DE CUlSINII_RE ............................. 26

Lampes de lahotte de cuisiniere ............................................... 26

Nettoyage ................................................................................... 27

SCHI_MAS DE C.&,BLAGE............................................................ 28

ASSISTANCE OU SERVICE ......................................................... 30

GARANTIE ..................................................................................... 31

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

m Use this unit only in the manner intended by the

manufacturer. Ifyou have questions, contact the

manufacturer.

m Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

m Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

m Do not operate any fan with a damaged cord or plug.

Discard fan or return to an authorized service facility for

examination and/or repair.

m Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

m When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

m Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

m Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

m Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flamb6).

m Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

m Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING: a

m SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

m NEVER PICK UP A FLAMING PAN - you may be burned.

m DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

m Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you

already know how to operate it.

- The fire is small and contained in the area where it

started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

aBased on "Kitchen Fire Safety Tips" published by NFPA.

m WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

READ AND SAVE THESE INSTRUCTIONS

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Level

• Drill

• 1W' (3 cm) drill bit

• 1/8"(3 ram) drill bit if installing into wood and a %e" (8 ram) drill

bit if installing optional backsplash kit.

• Pencil

• Wire stripper or utility knife

• Tape measure or ruler

• Pliers

• Caulking gun and weatherproof caulking compound

• Vent clamps

• Jigsaw or keyhole saw

• Flat-blade screwdriver

• Metal snips

• Phillips screwdriver

• Scissors

Parts needed

• Home power supply cable

• 1 - 1/2"(12.7 ram) UL listed or CSA approved strain relief

• 3 UL listed wire connectors

• 1 wall or roof cap

• Metal vent system

Parts supplied

Remove parts from packages. Check that all parts are included.

• 2 metal grease filters for 30" (76.2 cm) models

3 metal grease filters for 36" (91.4 cm) models

4 metal grease filters for 48" (121.9 cm) models

• Damper

• Hood canopy with blower and halogen lamps installed.

• 1 - 10" (25.4 cm) square to 10" (25.4 cm) round duct

transition.

• 2 - 175 watt infrared heat lamps

• Wood support

• Grease collectors

• 4- 6 x 80 mm mounting screws

• 4- 3.5 x 9.5 mm screws

• 5- M6 x 16 mm screws

• 5- D6.4 x 11 mm washers

• 2 - D5.3 x 20 mm washers

• 2 - 10 x 50 mm wall anchors

• T-20 TORX®tadapter

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial rating

plate is located inside the range hood on the rear wall of the

range hood.

Canopy range hood location should be away from strong draft

areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

The canopy range hood is factory set for venting through the roof

or through the wall.

All openings in ceiling and wall where canopy range hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local

codes.

Product Dimensions

Front view

18V_?'(45.9 cm) for 48" (121.9 crn) Hood

12V_?'(30.6 cm) for 36" (91.4 cm) Hood

9V_?'(23.0 cm) for 30" (76.2 cm) Hood

(16.5 crn)

(30.5cm)

21/4"

(5.7cm)

30" (76.2 cm)

36" (91.4 crn)

48" (121.9 cm)

(]5.7 cm)

25" (63.5 cm)

• 6-4.2x19mmscrews

1-®TORX is a registered trademark of Acument Intellectual Properties, LLC.

Back view Installation Dimensions

30" (76.2 cm), 36" (91.4 cm)

or 48" (121.9 cm)

cabinet opening width

(If installed between cabinets)

18"

(45.7cm)

12_3/16'' (32.5 cm) for 36" (91.4 cm) Hood

913/16"(24.9 cm) for 30" (76.2 cm) Hood

A. Top of hood

B. Wood support

C. Bottom of hood

D. Home wiring location

E.Knockout into terminal box

Optional Full-Width Duct Cover Installations

12"

(_.5 crn)

12"

(30._ cm)

18"

A. Optional full-width duct cover

B. Vent hood

18" (45.7 cm)

clearance upper

cabinet to countertop

Min. cabinet

opening width

Bottom of canc

to cooking

38"(91.4cm)

countertop height

A B

A. 84" (213.4 cm) minimum for

installations with canopy only.

B. 96" (243.8 cm) minimum for

installations with optional

duct cover.

IM PORTANT:

Minimum distance "X": 30" (76.2 cm)

Suggested maximum distance "X": 36" (91.4 cm)

Vent system must terminate to the outdoors.

Do not terminate the vent system in an attic or other enclosed

area.

• Do not use 4" (10.2 cm) laundry-type wall caps.

• Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

For the most efficient and quiet operation:

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24" (61.0 cm) of straight

vent between the elbows if more than 1 elbow is used.

• Do not install 2 elbows together.

• Use clamps to seal all joints in the vent system.

• The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

• Use caulking to seal exterior wall or roof opening around the

cap.

• The size of the vent should be uniform.

Cold weather installations

An additional back draft damper should be installed to minimize

backward cold air flow and a thermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

Venting Methods

A 10" (25.4 cm) round vent system is needed for installation (not

included). The hood exhaust opening is 10" (25.4 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates

back pressure and air turbulence that greatly reduce

performance.

Vent system can terminate either through the roof or wall.

Roof Venting Wall Venting

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent Piece Equivalent Length

45° elbow 2.5 ft

(0.8m)

90° elbow 5.0 ft

(1.5m)

The maximum equivalent vent lengths are:

10" (25.4 cm) round vents - 60 ft (18.3 m)

Example vent system

90°e,bow1 6. <,.8 .......wa,,cap

The following example falls within the maximum recommended

vent length.

1 - 90° elbow = 5.0 ft (1.5 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Length of system = 13.0 ft (3.9 m)

A. Roof cap A. Wall cap

B. 10" (25.4 cm) B. 10" (25.4 cm)

round vent* round vent*

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest

edition), or CSA Standards C22.1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0mM91 (latest edition) and all local codes

and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batte_march Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

Ifthehousehasaluminumwiring,followtheprocedure

below:

1. Connectasectionofsolidcopperwiretothepigtail

leads.

2. Connectthealuminumwiringtotheaddedsectionof

copperwireusingspecialconnectorsand/ortools

designedandULlistedforjoiningcoppertoaluminum.

Followtheelectricalconnectormanufacturer'srecommended

procedure.Aluminum/copperconnectionmustconformwith

localcodesandindustryacceptedwiringpractices.

• Wiresizesandconnectionsmustconformwiththeratingof

theapplianceasspecifiedonthemodel/serialratingplate.

Themodel/serialplateislocatedbehindthefilterontherear

walloftherangehood.

• WiresizesmustconformtotherequirementsoftheNational

ElectricalCode,ANSl/NFPA70(latestedition),orCSA

StandardsC22.1-94,CanadianElectricalCode,Part1and

C22.2No.0-M91(latestedition)andalllocalcodesand

ordinances.

INSTALLATIONINSTRUCTIONS

• It is recommended that the vent system be installed before

hood is installed.

• If you are installing the optional backsplash with shelves for

heat lamps, follow the instructions included with that product.

• Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

• Check that all installation parts have been removed from the

shipping carton.

1. Disconnect power.

2. Determine which venting method to use: roof or wall exhaust.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift range hood onto covered surface.

A. Wood support

B. Centerline

NOTE: The screws provided for mounting this hood must be

fastened into solid wood, do not fasten into sheet rock only.

Range Hood Mounting Screws Installation

The hood is attached to the wall with the wood support that is

attached to the back of the hood.

1. Determine and mark the centerline on the wall where the

canopy range hood will be installed.

2. Select a mounting height between a minimum of 30"

(76.2 cm) and a suggested maximum of 36" (91.4 cm), above

the cooking surface and the bottom of the range hood and

mark a horizontal reference line on the wall.

3. Remove the wood support from the back of the range hood

by loosening the 2 screws from the inside. Locate and level

the top of the wood support 153/8'' (39.1 cm) above the

marked horizontal line and centered on the vertical centerline.

Using 2 - 4 of the 6 x 80 mm screws, install wood support so

that it is screwed into at least 2 vertical studs.

Optional Duct Cover Installation

1. Attach the full-width duct cover to the top of the range hood

with the screws provided with duct covers. The duct cover

must be attached to the top of the range hood before

mounting the range hood to the wall. For information on

ordering the optional duct cover, see "Accessories" section.

Complete Preparation

1. Determine and make all necessary cuts in the wall for the vent

system. Install the vent system before installing the range

hood. See the "Venting Requirements" section.

2. Determine the location where the power supply cable will be

run through the wall.

3. Drill a 1V4"(3.2 cm) hole at this location.

4. Pull enough power supply cable through the wall to allow for

easy connection to the terminal box.

5. Install the 10" (25.4 cm) square x 10" (25.4 cm) round vent

transition with damper to top of the range hood using

(4) - 3.5 x 9.5 mm screws.

6. Remove terminal box cover and set aside.

7. Remove knockout from the back of the vent hood and install

a UL listed or CSA approved 1/2"strain relief. See "Make

Electrical Connection" section.

8. Place the range hood near its mounting position and run the

power supply cable through the strain relief into terminal box

(enough to make connection).

9. Tighten the strain relief screws.

The hood attaches to the wall by the 2 mounting screws in the

wood support mounted to the wall in the "Range Hood Mounting

Screws Installation" section.

1. Using 2 or more people, hang the range hood on the the wall

by placing the slotted holes in the range hood back over the 2

screws mounted to the wood support mounted to the wall.

NOTE: If your installation uses the optional duct cover, the

vent system needs to be connected to the hood and the duct

cover mounted to the top of the range hood before tightening

the mounting screws. See steps 5 and 6.

Slide the left mounting plate flange under the bracket.

/- .............................

A.Bracket

B.Mounting plate flange

Push the right end of the mounting plate up and snap into

spring tab.

NOTE: The spring tab should be outside of the slot in the

mounting plate.

2. Push the range hood up into the narrow slots, align the

bottom of the hood to the horizontal line, level the hood, and

tighten the 2 mounting screws.

3. Mark 2 lower mounting hole locations. Drill V8" pilot holes if

the holes are located into wood. If holes are not located into

wood, remove the hood and drill two 3/8"pilot holes and insert

10 x 50 mm wall anchors. Remount the hood, level, and

tighten the upper screws. Install 2 - 6 x 80 mm screws into

the lower mounting anchors and tighten.

4. Install 4 - 4.2 x 19 mm screws through the back of the hood

into the wood support and tighten.

5. Connect vent system to hood. Seal all joints with clamps.

6. If your installation uses the optional duct cover, mount it to

the top of the range hood following the instructions supplied

with the duct cover.

csnoe blo Bo Moto

Install the range hood blower motor assembly inside the hood

canopy with the wiring to the left.

A. Blower motor

.................................A

o o

A. Spring tab

4. Align mounting holes and install 5 - 6 x 16 mm screws.

A. Screw

B. Mounting hole

Attach power cord connector to connector on wire box on

blower motor mounting plate.

A. Blower motor mounting plate

B. Wire box connector

C. Power cord

Mc,, <®Eecffc<x Connect on

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Locate junction box inside of the range hood.

A. Terminalbox cover

B.Knockout in canopy

back into terminal box

A. White wires

B. Black wires

C. UL fisted wire connectors

D. Green, Bare or Yellow/Green wires

E. Home power supply

F. UL listed or CSA approved 1/2"strain relief

3. Use UL listed wire connectors and connect black wires (B)

together.

4. Use UL listed wire connectors and connect white wires (A)

together.

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

5. Connect green (or bare) ground wire from home power supply

to the green/yellow ground wire (C) in terminal box using UL

listed wire connectors.

6. Install terminal box cover.

7. Check all light bulbs to make sure they are secure in their

sockets.

8. Reconnect power.

Install Grease Filters. See "Range Hood Care" section.

Install Heat lamps into heat lamp sockets.

Check operation of the range hood blower and lights. See

"Range Hood Use" section.

E D

A. Infrared lamp

B. Grease filter handles

C. Grease filter

D. Blower control switch

E Halogen light switch

F. Halogen lights

G. Infrared lamp controls

4. If range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

Disconnect power supply and check that the wiring is

correct.

NOTE: To get the most efficient use from your new range hood,

read the "Range Hood Use" section.

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after the

cooking is complete to clear all smoke and odors from the

kitchen.

The hood controls are located on the right-hand underside of the

OFF

_"S'_ OFF

range hood.

OFF

A. Infrared lamp switch

B. Halogen light switch

C. Blower control switch

Operating the lights

1. Turn the light switch to the "Night" position to use the range

hood lights as a night light.

2. Turn the light switch to the "High" position to turn the range

hood lights On.

3. Turn the light switch to the "Off" position to turn the range

hood lights Off.

Operating the blower

1. Turn the blower switch to the first position to turn the range

hood on Low.

2. Turn the blower switch to the second position to turn the

range hood on Medium.

3. Turn the blower switch to the third position to turn the range

hood on Medium - High.

4. Turn the blower switch to the High position to turn the range

hood on High.

5. Turn the blower switch to the "Off" position to turn the range

hood blower Off.

Operating the heat lamp

NOTE: Heat lamp bulbs should be rated to a maximum of

175 watts each.

Food Poisoning Hazard

Do not let food sit for more than one hour before or

after cooking.

Doing so can result in food poisoning or sickness.

1. Turn the heat lamp switch to the "High" position to turn the

heat lamps On.

2. Turn the heat lamp switch to the "Off" position to turn the

heat lamps Off.

RANGE HOOD CARE

Replacing a Halogen Lamp

Turn off the range hood and allow the halogen lamp to cool. To

avoid damage or decreasing the life of the new bulb, do not

touch bulb with bare fingers. Replace bulb, using tissue or

wearing cotton gloves to handle bulb.

If new lamps do not operate, make sure the lamps are inserted

correctly before calling service.

1. Disconnect power.

2. Push up on the lens and turn it counterclockwise.

I '

3. Remove the bulb and replace it with a 120-volt, 50-watt

maximum halogen bulb with a GU10 base. Turn it clockwise

to lock it into place.

4. Repeat steps 2-3 for the other bulb if needed.

5. Reconnect power.

Replacing the Infrared Heat Lamps

Turn off the range hood and allow the infrared heat lamp to cool.

To avoid damage or decreasing the life of the new lamp, do not

touch lamp with bare fingers. Replace lamp, using tissue or

wearing cotton gloves to handle lamp.

If new lamps do not operate, make sure the lamps are inserted

correctly before calling service.

1. Disconnect power.

2. Twist lamp counterclockwise to remove.

3. Remove the lamp and replace it with a 120-volt, 175-watt

maximum, PAR38 IR lamp made for E-26 base. Twist lamp

clockwise to screw it into place.

4. Repeat steps 2 - 3 for the other lamp if needed.

5. Reconnect power.

Exterior surfaces:

To avoid damage to the exterior surface,do not use steel wool or

soap-filled scouring pads. Rub in direction of the grain line to

avoid scratching the surface.

Always wipe dry to avoid water marks.

• Stainless Steel Cleaner and Polish.

• Mild liquid detergent and water.

• Wipe with damp soft cloth or nonabrasive sponge, then rinse

with clean water and wipe dry.

Metal Filters and Drip Trays:

Use 2 hands to remove filters. Grasp filter handles, pull toward

the front of range hood and pull down on the rear handle to

remove. Repeat for each filter.

A.Grease filter

Remove grease drip tray.

A. Drip tray

Wash metal filters and grease trays as needed in dishwasher or

hot detergent solution to clean.

Replace grease drip tray.

Reinstall filters, grasp filter handles and place front edge of filter

into the hood. Push up on the back handle and set rear of filter

into the drip tray to secure. Repeat for each filter.

A. Grease filter

Thermal Protector

The range hood is equipped with athermal protector to avoid

overheating conditions. If the range hood shuts off while in use,

move the blower switch to the OFF position. Wait approximately

60 minutes, then move the blower switch to the first position to

restart the range hood.

WIRING DIAGRAMS

30" and 36" (76.2 cm and 91.4 cm) models

L N $

Y/G

' W

SEIXXA

1 Y/G

Y/G

Bw_

.............C

r--Co

--o_.

3--

2 m

--I

/11111

Aut°_ ....

Transformer

Y/G

8@-

e _--

48"(121.9cm)models

N GND

Y/G

' W

Y/G

r--co

",--- _ C 3 _-

SEIXYA

Y/G

_-!-

Y/G

Y/G i[--

w _lw

m @ m

GY Q GY

BK Q BK

BU (Z) I BU

w I_ w

5 m

1 -

(

1 a

_00

--3 o,._,..__.

)

ASSISTANCEOR SERVICE

When calling for assistance or service, please know the purchase

date and the complete model and serial number of your

appliance. This information will help us to better respond to your

request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new appliance. To locate factory

specified replacement parts in your area, call us or your nearest

designated service center.

Call the dealer from whom your appliance was purchased, or call

1-800-JENNAIR (1-800-536-6247) to locate an authorized

service company. When calling, please know the purchase date

and the complete model and serial number of your appliance. Be

sure to retain proof of purchase to verify warranty status.

If the dealer or service company cannot resolve your problem,

write to:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Web address: www.jennair.com

Or call: 1-800-536-6247

U.S. customers using -I-I-Yfor deaf, hearing impaired or speech

impaired, call: 1-800-688-2080 (Monday - Friday, 8:00 a.m. -

8:00 p.m. Eastern Time).

NOTE: When writing or calling about a service problem, please

include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt).

User's guides, service manuals and parts information are

available from Jenn-Air Brand Home Appliances, Customer

eXperience Center.

Full-Width Duct Cover

Order Part Number W10272079 for 30" (76.2 cm) model

Order Part Number W10272080 for 36" (91.4 cm) model

Order Part Number W10272081 for 48" (121.9 cm) model

Backsplash Kit (with shelves)

Order Part Number W10285447 for 30" (76.2 cm) model

Order Part Number W10285448 for 36" (91.4 cm) model

Order Part Number W10285449 for 48" (121.9 cm) model

Call the dealer from whom your appliance was purchased, or call

Jenn-Air at 1-800-807-6777 to locate an authorized service

company. When calling, please know the purchase date and the

complete model and serial number of your appliance. Be sure to

retain proof of purchase to verify warranty status.

If the dealer or service company cannot resolve your problem,

write to:

Jenn-Air Brand Home Appliances

Customer eXperience Centre

1901 Minnesota Court

Mississauga, ON L5N 3A7

Web address: www.jennair.ca

Or call: 1-800-807-6777.

NOTE: When writing or calling about a service problem, please

include the following information:

1. Your name, address and daytime telephone number.

2. Appliance model number and serial number.

3. Name and address of your dealer or servicer.

4. A clear description of the problem you are having.

5. Proof of purchase (sales receipt).

User's guides, service manuals and parts information are

available from Jenn-Air Brand Home Appliances, Customer

eXperience Centre.

JENN-AIR MAJOR APPLIANCEWARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Jenn-Air brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Jenn-Air") will pay for factory

specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Jenn-Air designated

service company. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used

in the country in which it was purchased. Outside the 50 United States and Canada, this limited warranty does not apply. Proof of

original purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use or when it is used in a manner that is

contrary to published user or operator instructions and/or installation instructions.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by Jenn-Air.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Jenn-Air within 30 days from the date of purchase.

6. Any food loss due to refrigerator or freezer product failures.

7. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be

repaired in the home and only in-home service is covered by this warranty.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Jenn-Air servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with published installation instructions.

11. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty

is void if the factory applied serial number has been altered or removed from your major appliance.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. JENN-AIR SHALL NOT BE LIABLE FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

If outside the 50 United States and Canada, contact your authorized Jenn-Air dealer to determine if another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," you may find

additional help by checking the "Assistance or Service" section or by calling Jenn-Air. In the U.S.A., call 1-800-536-6247. In Canada,

call 1-800-807-6777. 6/09

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

SECURITEDELA HOTTEDECUISINIERE

Votre securite et celle des autres est tres importante.

Nous donnons de nombreux messages de s_curit_ importants dans ce manuel et sur votre appareil m_nager. Assurez-vous de

toujours lire tousles messages de s_curit_ et de vous y conformer.

Voici le symbole d'alerte de s_curit&

Ce symbole d'alerte de s_curit_ vous signale les dangers potentiels de d_c_s et de blessures graves &vous

et & d'autres.

Tous les messages de s_curit_ suivront le symbole d'alerte de s_curit_ et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d_cbs ou de blessure grave si vous ne

suivez pas imm_diatement les instructions.

Risque possible de d_cbs ou de blessure grave si vous

ne suivez pas les instructions.

Tousles messages de s_curit_ vous diront quel est le danger potentiel et vous disent comment r_duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

llVIPORTANTES iNSTRUCTiONS DE Sl CURITl

AVERTISSEMENT : POUR REDUIRE LE RISQUE

D'INCENDIE, CHOC ¢:LECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

m Utiliser cet appareil uniquement dans les applications

envisag_es par le fabricant. Pour toute question, contacter

le fabricant.

m Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre I'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour emp6cher tout r_tablissement accidentel de

I'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller le tableau de disjoncteurs, placer sur le tableau

de disjoncteurs une 6tiquette d'avertissement pro6minente

interdisant le r@ablissement de I'alimentation.

m Tout travail d'installation ou c&blage 61ectrique doit @re

r6alis_ par une personne qualifi6e, dans le respect des

prescriptions de tousles codes et normes applicables, y

compris les codes du b&timent et de protection contre les

incendies.

m Ne pas faire fonctionner un ventilateur dont le cordon ou la

fiche est endommag6(e). Jeter le ventilateur ou le retourner

&un centre de service agr66 pour examen et/ou r6paration.

m Une source d'air de d_bit suffisant est n6cessaire pour le

fonctionnement correct de tout appareil a gaz (combustion

et 6vacuation des gaz & combustion par la chemin6e), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de I'_quipement de chauffage et

les prescriptions des normes de s_curit_ - comme celles

publi_es par la National Fire Protection Association (NFPA)

et I'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorit6s r6glementaires locales.

m Lors d'op@ations de d6coupage et de per£age dans un mur

ou un plafond, veiller a ne pas endommager les c&blages

61ectriques ou canalisations qui peuvent s'y trouver.

m Les ventilateurs d'6vacuation doivent toujours d6charger

I'air a I'ext@ieur.

MISE EN GARDE : Cet appareil est congu uniquement

pour la ventilation g6n@ale. Ne pas I'utiliser pour I'extraction

de mati_res ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et 6vacuer ad6quatement les gaz, veiller &acheminer I'air

aspir6 par un conduit jusqu'b, I'ext@ieur - ne pas d6charger

I'air aspir6 dans un espace vide du b&timent comme une

cavit_ murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR REDUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

METALLIQUES.

AVERTISSEMENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINIF:RE :

[] Ne jamais laisser un _16ment de surface fonctionner &

puissance de chauffage maximale sans surveillance. Un

renversement/d6bordement de mati@e graisseuse pourrait

provoquer une inflammation et la g6n@ation de fum_e.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

[] Veiller & toujours faire fonctionner le ventilateur de la hotte

Iors de la cuisson avec une puissance de chauffage _lev_e

ou Iors de la cuisson d'un mets & flamber (& savoir crSpes

Suzette, cerise jubil6e, steak au poivre flamb6).

[] Nettoyer fr6quemment les ventilateurs d'extraction. Veiller &

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

[] Utiliser toujours un ustensile de taille appropri6e. Utiliser

toujours un ustensile adapt_ & la taille de 1'616ment

chauffant.

AVERTISSEMENT : POUR REDUIRE LE RISQUE DE

DOMMAGES CORPORELS APR_:S LE DECLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINI_:RE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :a

[] Placer sur le r6cipient un couvercle bien ajust_,, une t61e &

biscuits ou un plateau m6tallique POUR ETOUFFER LES

FLAMMES, puis @eindre le brt_leur. VEILLER ,_ ¢:VITER

LES BRULURES. Si les flammes ne s'_teignent pas

imm_diatement, CVACUER LA PIECE ET APPELER LES

POMPIERS.

[] NE JAMAIS PRENDRE EN MAIN UN RECIPIENT

ENFLAMMt _ - vous risquez de vous brQler.

[] NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brQlante.

[] Utiliser un extincteur SEULEMENT si :

- II s'agit d'un extincteur de classe ABC, dont on connaft le

fonctionnement.

- II s'agit d'un petit feu encore limit6 & I'endroit oQ il s'est

d6clar&

- Les pompiers ont 6t_ contact,s.

- II est possible de garder le dos orient_ vers une sortie

pendant I'op@ation de lutte contre le feu.

aRecommandations tir_es des conseils de s_curit_ en cas

d'incendie de cuisine publi_s par la NFPA.

[] AVERTISSEMENT : Pour r_duire le risque d'incendie

ou de choc _lectrique, ne pas utiliser ce ventilateur avec un

quelconque dispositif de r_glage de la vitesse &semi-

conducteurs.

LIRE ET CONSERVER CES INSTRUCTIONS

EXlGENCESD'INSTALLATION

Rassembler les outils et pieces necessaires avant de commencer

I'installation. Lire et suivre les instructions fournies avec les outils

indiques ici.

Outils n_cessaires

• Niveau

• Perceuse

• Foret de 11¼"(3 cm)

• Foret de 1/8"(3 mm) en cas d'installation dans du bois et foret

de %6" (8 mm) en cas d'installation de I'ensemble de dosseret

facultatif.

• Crayon

• Pince a denuder ou couteau utilitaire

• Metre-ruban ou regle

• Pince

• Pistolet a calfeutrage et compose de calfeutrage resistant

aux intemperies

• Brides de serrage pour conduit d'evacuation

• Scie sauteuse ou scie a guichet

• Tournevis a lame plate

• Cisaille de ferblantier

• Tournevis Phillips

• Ciseaux

Pi_ces n_cessaires

• C&ble d'alimentation electrique du domicile

• 1 serre-c&ble de 1/2"(12,7 mm) (homologation UL ou CSA)

• 2 connecteurs de fils homologues UL

• 1 bouche de decharge (decharge a travers lemur ou & travers

le toit)

• Conduit d'evacuation metallique

Pi_ces fournies

Retirer les pieces des emballages. Verifier que toutes les pieces

sont presentes.

• 2 filtres a graisse metalliques, pour modele de 30" (76,2 cm)

3 filtres a graisse metalliques, pour modele de 36" (91,4 cm)

4 filtres a graisse metalliques, pour modele de 48" (121,9 cm)

• Clapet

• Auvent de hotte avec ventilateur et lampes a halogene.

• 1 raccord de conduit carre de 10" (25,4 cm) a conduit rond de

10" (25,4 cm).

• 2 lampes a rayons infrarouges de 175 watts.

• Support en bois

• Collecteurs de graisse

• 4 vis de montage de 6 x 80 mm

• 4 vis de 3,5 x 9,5 mm

• 6visde4,2x19mm

• 5visdeM6x16mm

• 5 joints de D6,4 x 11 mm

• 2 joints de D5,3 x 20 mm

• 2 chevilles d'ancrage de 10 x 50 mm

• Adaptateur TORX®tT-20

Ex ge sces eye}em cs

IMPORTANT : Observer les dispositions de tousles codes et

reglements en vigueur.

Confier I'installation de la hotte _ un technicien qualifie. C'est

I'installateur qu'incombe la responsabilite de respecter les

distances de separation specifiees sur la plaque signaletique de

I'appareil. La plaque signaletique est situee a I'interieur de la

hotte, sur la paroi arriere.

On dolt toujours installer la hotte a distance des sources de

courant d'air (fen_tres, portes et bouches de chauffage).

Respecter les dimensions indiquees pour les ouvertures

decouper dans les placards. Ces dimensions tiennent compte

des valeurs minimales des degagements de separation.

Cette hotte a ete configuree & I'usine pour une decharge atravers

le toit ou a travers lemur.

Assurer I'etancheite au niveau de chaque ouverture decoupee

dans le plafond ou lemur pour I'installation de la hotte de

CUlSlnlere.

Installation dans une r_sidence mobile

L'installation de cette hotte dolt satisfaire aux exigences de la

norme Manufactured Home Construction Safety Standards, Titre

24 CFR, partie 328 (anciennement Federal Standard for Mobile

Home Construction and Safety, titre 24, HUD, partie 280); Iorsque

cette norme n'est pas applicable, I'installation dolt satisfaire aux

criteres de la plus recente edition de la norme Manufactured

Home Installation 1982 (Manufactured Home Sites, Communities

and Setups) ANSI A225.1/NFPA 501A*, ou des codes et

reglements Iocaux.

Dimensions du produit

Vue avant

18V_" (45,9 cm) pour hotte de 48" (121,9 cm)

12V_" (30,6 cm) pour hotte 36" (91,4 cm)

9_/_6'' (23,0 cm) pour hotte 30" (76,2 cm)

(16,5 cm)

12" (30,5 crn)

21/4"

30" (76,2 crn)

36" (91,4 cm)

48" (121,9 crn)

"(]5,7 cm)

25" (63,5 crn)

1-®TORX est une marque d6pos&e de Acument Intellectual Properties, LLC.

Vue arri_re Dimensions d'installation

30" (76,2 crn), 36" (91,4 cm)

ou 48" (121,9 cm)

cavite d'encastrement

(en cas d'installation entre des placards)

18"

(45,7cm)

12_3/16'' (32,5 cm) pour hotte de36" (91,4 cm)

913/16"(24,9 cm) pour hotte de 30" (76,2 cm)

A. Haut de la hotte

B. Support en bois

C. Bas de la hotte

D. Emplacement du c#blage de

la maison

E. Qpercule arrachable dans le

boTtier de connexion

Installations alternatives avec cache-conduit pleine

largeur

12"

(_,5 em)

12"

(30,_ cm)

18"

A. Cache-conduit pleine largeur facultatif

B. Hotte

18" (45,7 cm)

de d#gagement minimum

entre le

et le plan de travail

36"(91,4cm)

dehauteur jusqu'au

plan de travail

_ouvercle de 1'6vent

(le cas #cheant)

Cavite d'encastrement

minimum

Dubasdela hotte

ala surfacede

_13" (33,0 cm)

A B

A. 84" (213,4 cm) minimum pour

les installations avec hotte

uniquement.

B. 96" (243,8 cm) minimum pour

les instaflations avec cache-

conduit facultatif ou

ensemble de chemin_e

t_l_scopique.

IMPORTANT :

Valeur minimale de la distance "X" : 30" (76,2 cm)

Valeur maximale sugger6e pour la distance "X" :36"

(91,4 cm)

• Le systeme d'evacuation doit decharger I'air a I'exterieur.

• Ne pas terminer le systeme d'evacuation dans un grenier ou

dans un autre espace ferme.

• Ne pas utiliser une bouche de decharge murale de

4" (10,2 cm) normalement utilisee pour un equipement de

buanderie.

• Utiliser un conduit metallique uniquement. Un conduit en

metal rigide est recommand& Ne pas utiliser un conduit de

plastique ou en feuille metallique.

• La Iongueur du systeme d'evacuation et le nombre de coudes

doit _tre reduit au minimum pour fournir la meilleure

performance.

La page charge ...

Jenn-Air JXW9030WP Le manuel du propriétaire

Marque: Jenn-Air

Modèle: JXW9030WP

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Jenn-Air JXW9030WP Owner's manual

Jenn-Air JXW9030WP Le manuel du propriétaire

Ce manuel convient également à

Jenn-Air JXW9030WP Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents