Bluewave NE4488 Manuel utilisateur

Marque: Bluewave

Modèle: NE4488

Catégorie: Accessoires de piscine hors terre

Taper: Manuel utilisateur

Ce manuel convient également à

VER.1219

bove Ground P

ol Filte

& Pum

Manu

NE4487

NE4488

NE4489

CONGRATULATIONS!

YOU HAVE PURCHASED A HIGH QUALITY FlowXtreme FILTRATIONS

SYSTEM FOR YOUR ABOVE GROUND POOL. YOUR NEW FILTER

SYSTEM HAS BEEN MANUFACTURED AND TESTED TO OFFER MANY

YEARS OF TROUBLE FREE SERVICE.

IMPORTANT – READ THIS MANUAL CAREFULLY

A. Safety Warnings

Read all Warnings and Cautions noted below. Failure to do so could result in serious or fatal injury.

 Prior to installation of this unit, carefully read and adhere to all CAUTION, ATTENTION, and ADVICE

notices located throughout this manual. Failure to comply with these instructions can cause serious injury,

death, or damage to the unit.

 RISK OF SUCTION ENTRAPMENT HAZARD, WHICH, IF NOT AVOIDED CAN RESULT IN

SERIOUS INJURY OR DEATH. Do not block pump suction at the pump or in the pool as this can cause

severe injury or death.

 Electrical wiring MUST be installed by trained professional and adhere to local code and regulations.

 Avoid electric shock. DO NOT USE power extension cords.

 Connect ONLY to a Ground-Fault Circuit Interrupter (GFCI) power outlet. Consult a qualified professional

electrician for safe and proper installation of a qualified electrical outlet.

 Consult and follow all local and national codes related to swimming pools and their equipment.

 Incorrectly installed equipment may fail, causing severe injuries or damage to the pump-filter system.

 Never submerge the filter and/or pump in water.

 Never place the pump or filter in your pool.

 Trapped air in the pump-filter system may cause the TANK COVER to be blown off which can result in

death, serious injury, or damage to the pump-filter system. Ensure all air is out of system before operating.

 Never change the 7 Position Multi-Port Valve while the system is operating. Doing this repeatedly will

damage internal components of the valve and not be covered under warranty.

 ALWAYS unplug the system before changing positions on the control valve.

 Install this product with sufficient safety margin from the pool to prevent children from using the system to

access the pool.

 Never PLUG or UNPLUG this unit from an electrical source while standing in water.

 NEVER service this unit with electrical power cord connected.

 DO NOT operate the system while the pool is being used.

 KEEP CHILDREN AWAY from all electrical equipment.

 NEVER ALLOW CHILDREN TO OPERATE THIS EQUIPMENT.

 The Pool Owner should always exercise caution and common sense when utilizing their swimming pool and

operating equipment.

B. General Information

This manual provides information relating to the installation, utilization and maintenance of our filtration system.

We recommend that you read this manual in its entirety and keep it for future reference,

The pump included with the filtration system is a horizontal, self-priming centrifugal pump. For the pump to

function correctly, the water temperature must not exceed 35℃/95℉. The materials used in the pump have

undergone stringent hydraulic testing and electrical inspections.

The filter tank included in the filtration system consists of high-grade polypropylene (PP). It is manufactured as a

single unit (absolutely corrosion resistant and resistant to commercially available swimming pool chemicals).

(Prerequisite: Compliance with the standard recommended specifications for the pH- and chlorine value). It is

equipped with a tank drainage system, pressure gauge. The filter tank comes ready to attach and is supplied with a

user-friendly 7 Position Multi-Port Valve attached to the tank cover, an approved filter pump with hair and lint

basket, and a plastic base for ready on- site mounting.

Read this manual carefully before installation. The filtration system and pump must be installed in accordance

with all federal and local codes and standards in effect for the area of installation.

We decline all responsibility for the consequences of failure to comply with the installation instructions. We

recommend that you comply with the power source instructions to avoid overloading the pump motor and/or

electric shock.

This filtration system is not intended for use by persons with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge.

Safety notes and information boxes should always be observed.

C. Safety Notes

Your filter pump was constructed and tested and left the manufacturing plant in technically operational condition.

In order to maintain this condition and ensure safe operation, the user should observe the notes and product

information contained in this technical manual. If there is any indication that safe operation is no longer possible,

the device is to be disconnected from the power supply and secured against accidental use.

This is the case when:

 The device has visible damage.

 The device no longer appears functional.

 After long periods of storage in poor conditions.

If the power cord or other parts of this equipment are damaged, they have to be replaced by the manufacturer or its

service agent or a similarly qualified person in order to avoid danger.

D. Damage during delivery

Your filter system has been carefully and professionally packed for delivery. Please check to ensure that the

package is undamaged and that all parts are in the box (see the parts lists at the end of this manual). If you

purchased this product on order and the product was shipped to you, ensure that delivery is complete. Damage to

product as a result of shipping is not the responsibility of the supplier and must be immediately reported to the

shipper. The shipper assumes the liability for damages during delivery, the supplier is not responsible for it.

E. Implied Warranty

The manufacturer warranties safe operation and reliability only under the following conditions:

 The filter system is installed and operated according to the assembly and operating instructions.

 Only original replacement parts are used for repairs or replacements (consumable & expendable parts do no

fall under the warranty).

Expendable parts that do not fall under the warranty include:

 All O-rings

 Pressure gauge

 Mechanical seal, complete

 Hoses and metal hose clamps

F. Resultant Damages

We cannot be responsible for damages to the product if the product is not used in accordance with the instructions

provided.

G. Technical Data and Specifications

 The recommended filter run time is twice a day for 4 to 5 hours; regular backwashing time is 2-3 minutes at

least once a week, and floor vacuum cleaning as needed are the basic pump requirement for maintaining

clean swimming pool water!

 The major components for this model are: (Confirm you have all these components before starting

installation)

The Tank lid with 7-way valve, filter pump, filter tank, 1 1/4’’-1 1/2’’ hose connectors and base plate.

NE4487 NE4488 NE4489

Flow rate: 2100 GPH 2300 GPH 5400 GPH

MAX Operating Pressure: 22 psi 22 psi 22 psi

Related Voltage: 110V AC 60Hz 110V AC 60Hz 110V AC 60Hz

Power 1/2HP 3/4 HP 1 HP

Amount of Sand: Max 35lbs Max 75lbs Max 100lbs

Pool size: Max 4,000 US gallons Max 8,000 US gallons Max 20,000 US gallons

H. Unpacking your filter system

Carefully remove the product and all component parts from the box. Cross reference all parts in the box with the

parts list reference chart to make certain all parts are present before beginning assembly.

NOTE: Some parts may be located within the filter tank. To access these parts, you must remove the tank cover.

Refer to *pages 10-15 for complete EXPLODED VIEW PARTS DIAGRAMS.

I. Power source instructions

1.The Above Ground filter pump system you have purchased is equipped with a standard electrical cord and

plug which should only be connected to a power outlet protected by a 30 Amp

Ground-Fault-Circuit-Interrupter (GFCI) that has been installed by a professional electrician and adheres to

local codes and regulations.

2. To avoid electric shock, power cord extensions should not be used.

J. Positioning your filter system

 For the operation of this filter system with Above Ground pools, you need a skimmer installed in your

pool. Either an integrated skimmer (built into the pool wall) or a suspended floating skimmer (attachment

to the pool wall).

 The installation area must allow an adequate safety margin to the pool wall. Refer to local and national

codes for required distance between the filter system and the pool wall.

 We recommend putting the filter system on a concrete slab or similar. Be sure the

Installation site is level.

 Additional installation accessories such as hoses, hoses clamps, and filter sand

(not included) are available from your pool dealer.

K. Filter-Pump Assembly (Figures 1-3)

1. Filter pump & Base Plate assembly

a. Secure water pump to the base plate with the provided pump mounting hardware. Orient as shown.

(Figure1)

b. Place the base plate and pump in the location where the Pump Filter System will be located for normal

operation and within reach of the pool filter and return hoses but with a sufficient safety margin from the edge

of the pool. Attach the filter tank to the base plate as shown. The feet on the bottom of the filter tank fit within

the holes provided on the base plate (Figure 3).

c. Filling sand chamber with sand (Figure 4-7)

 Position the filter pump assembly to the location you have dedicated for its operation. NOTE: Do this

before you fill the chamber with sand as the unit will become heavy and difficult to move around.

 Check to ensure that the bottom strainer is correctly positioned.

 Check to ensure that the tank separator plate is seated properly.

 Check to ensure that the upper distributor is located under the tank cover.

 Fill the sand chamber half full with water.

 Pour #20 Pool Filter Grade silica sand into the SAND FILTER CHAMBER being careful not to allow any

sand to enter the FILTERED WATER CHAMBER.

NOTE: Installation of sand other than #20 Pool Filter Sand will NOT function properly,

and may void your warranty.

d. Secure the lid/valve to the filter tank (Figure 8)

 Ensure the main tank seal around the top of the filter tank is in good condition and securely seated in the

groove. Be sure groove is free of sand.

 Carefully place the tank cover onto the filter tank. The tank cover should be oriented so that the notch on

the cover is aligned with the matching tab on the filter tank-this ensures proper alignment.

 Secure tank cover and filter tank with the tank cover lock ring assembly and tighten with the knob and

bolt.

2. Pump hose connections (Figure 9-18)

a. Attach the 1¼” / 1½” hose connector & collar onto the intake port of the filter pump. Ensure that the

O-ring is installed between the port and the connector.

b. Skimmers: Connect hose from pool skimmer to the intake fitting on the filter pump. Secure with a hose

clamp.

c. Pressure line: Connect the flexible 1½” hose from the upper discharge point on the top of the filter pump to

the connector with designation “PUMP” on the 7-way valve. (Figures 13&18)

d. Return line: Connect a flexible hose (not included with your system) from the 7-way valve port with the

designation “RETURN” to the return fitting or connection for the pool location. Secure all connections

with hose clamps. (Figures 13 & 18)

If using flexible hose: Lightly lubricate the pool return port on the tank cover with petroleum jelly.

Secure with a hose clamp.

NOTE: Be careful not to secure return hose to the waste/backwash port.

e. Backwash: Connect to “WASTE” using backwash hoses and clamps. Backwash hose and clamps are

available from your local swimming pool retail professional.

f. Connecting the filter system

This Pool filter system is designed to connect to pools with standard 1½” diameter hose connectors. If your

pool has a hose connector size and/or type different than described here, you may need to purchase an adapter

at your local pool supply store or hardware retailer.

Before you begin to connect hoses to the filter and pump, make certain that no water can flow through the

intake or return hoses connected to the pool. Some pools have shut off valves in their intake and return ports,

others do not. If you do not have a shut off valve, block the ports with a removable plug to prevent water

from passing into and through the hoses.

These instructions assume that the pool is already assembled with hoses attached to the water intake and

return ports on the pool.

L. Filter system start up

WARNING – Never rotate the valve handle while the pump is running. You will damage the Diverter

Gasket inside the 7-position multi-port valve. Damage to the Diverter Gasket will not be covered under

warranty.

It is important that you read and follow the instructions on proper power supply sources.

Once the filter system has been properly assembled, the tank filled with sand and the hoses connected as described,

you may begin filtration. However, we recommend that you first clean and prepare the new sand. Cleaning the

sand prior to filtering your pool will remove most of the dust and tiny sand particles that may exist in the sand. If

you move straight to filtering, these particles will end up in your pool. To clean the sand, please follow the

instructions below.

Do not turn on the system until advised to do so.

Note: Do not back wash on initial installation if filter media is Cotton Tails. Follow the use instructions

provided with Cotton Tails.

1. Make certain the pump is not plugged into a power supply.

2. Start with the multi-position valve in the 5 Closed position.

3. If you haven’t done so already, fill your pool with water. Ensure that the water level is at least 1”-2” above the

top of the hose intake (Skimmer) and return ports in the pool.

4. Release the shut off valve at the intake port (Skimmer) in the pool. If you plugged the intake port (Skimmer),

remove the plug to allow the water to flow into the intake hose. You may need to partially open one of the large

clear view port covers to act as an air relief valve to completely fill the tank with water.

5. With the filter-pump system installed in a location level lower than your pool’s water level-water will

automatically flow into the pump-filter system.

6. Allow the filter tank to fill with water.

7. Check for leaks and make any adjustments needed to stop leaks found. It may be necessary to use “Teflon” tape

wrapped around the hose fitting threads. Teflon Tape is available at pool or hardware stores if not included in your

filter package.

8. When you first fill your filter tank with sand it is necessary to clean the small particles and dust from the new

sand. If you do not do this you will blow this dust and small particles into your pool. To properly clean the new

sand follow the backwash process described below:

 Turn off the Motor / Pump at the Power Source.

 Attach backwash hose (not included) to backwash port. Available at a local pool store.

 Place the Multi-Port Valve in the “4 – Backwash” position.

 Turn on the Pump

 Run filter in BACKWASH mode until discharge water is clear.

 Turn off the Motor / Pump at the Power Source.

 Place the Multi-Port Valve in the “2 – RINSE” position.

 Turn on the Pump.

 Allow filter to run for 60 seconds to remove any remaining sand or debris residue from pump and valve

plumbing.

 Turn off the Pump at the Power Source.

 Place the Multi-Port Valve in the “1 – Filtration” position.

 Turn on the Pump.

 Your filtration system is running and ready for further operation.

M. 7-Position Multi-Port Filter Valve Position Operation

Setting Complete water flow/function

Filter

Position 1

Picture 19

Function: Regular pool filter action & vacuuming. This is the setting the filter will be

set to most of the time. In this position, water is directed through the top of the filter

where it compresses and flattens down the sand. Contaminations are trapped by the

sand as water makes it way to the bottom strainer, out of the filter and back to the

pool.

Rinse

Position 2

Picture 20

Function: Use after backwashing to clean the filter bed. This should always be done

immediately after backwashing, new sand addition or filter start-up. In this position,

water is directed to the top of the tank where it flushes the valve while sending water

out the waste line.

Circulation

Position 3

Picture 21

Function: Circulate water after chemical treatment. This position is used during

certain pool cleanups and chemical treatments when you don’t want the water

contaminating the sand. In this position, water is only directed through the valve back

to the pool and does not filter through the sand.

Backwash

Position 4

Picture 22

Function: Clean filter of captured debris. This is the position needed to clean the filter

& the sand. You’ll know it is time to backwash when the pressure gauge shows more

than 10 PSI above what it normally reads when the filter is clean. In this position,

water is directed through the bottom strainer, reversing the flow through the tank.

This causes the sand to separate and lift while releasing trapped debris out the waste

port and backwash hose.

Closed

Position 5

Picture 23

Function: Cleaning the hair and lint strainer. This position stops the flow of water

into the pump and filter.

CAUTION: Do not run pump with valve in this position.

Purge/Drain

Position 6

Picture 24

Function: Bypass the filter. This position is ideal for vacuuming pools with large

amounts of debris or after an algae treatment. In this position, water bypassed the

filter and sends all the water and contaminates out the waste line.

Winterize

Position 7

Picture 25

Function: Winterizing and storage. In this position, the valve lever is between

positions which removes pressure from internal valve components for winter

(off-season) storage.

CAUTION: Do not run pump with valve in this position.

N. Manual Vacuuming the Pool

1. For Above Ground Pools

Vacuuming is done in valve position #1, Filter, on the valve. The pool vacuum is connected by use of a pool

vacuum hose and vacuum plate directly into the skimmer. Do not turn on the pump until the pool vacuum is

connected and ready for operation.

Important: The pool vacuum hose must be fully filled with water so that the pump does not lose prime and fill the

tank with air.

P. Winterize the system in cold weather climates

 Unplug the pump from the power source.

 Close the shut off valves or block the flow of water at the pool inlet and return ports.

 Disconnect the filtration system from the pool, drain the tank and hoses.

 Place the handle on the central valve in position 7- ‘Winterize’ to relieve the tension on the spring and

internal valve components. This prevents the Diverter Gasket from becoming stuck to the gasket seat over

the winter and damaged in the spring start up procedure.

 Store the filter system in a location protected from frost and severely cold temperatures. In a garage or

insulated storage shed is recommended.

Q. Important Do’s & Don’ts

DO’S:

 Be aware and make note of the filter pressure when the sand is clean. Backwash when you see an increase

of 10 PSI on the pressure gauge.

 Backwash long enough to clean the sand bed. Let the system backwash until the water leaving the waste

line is clear. Note that backwashing can remove 50 – 300 gal of water from your pool so pay attention.

Also, be aware of local codes regarding pool water disposal as some communities have rules or codes

regarding pool water drainage.

 Protect bottom strainer while replacing or adding sand. Fill the tank with 8” – 12” (about 1/8 of tank

height) of water. Cover the water chamber to avoid getting sand inside.

 Start filter in Backwash mode for several minutes and then for about 1 minute in the rinse mode before

initial startup or after adding new sand. By doing this you can avoid blowing small particles and

impurities from the new sand into your pool. If some debris from new sand does go into your pool,

vacuum it with the system in purge mode, otherwise you may send it back to the pool.

DON’TS: Observe these cautions carefully or you may cause non-warranty damage to your filter

system.

 Move valve handle while the pump is running. It will damage the valve and possibly other equipment as

well.

 Backwash excessively. Sand filters operate more efficiently during mid-cycle. Some level of debris in the

sand bed actually helps filtration and makes the filter more effective. Too much backwashing will reduce

efficiency.

 Vacuum the pool in backwash mode. You can plug up the strainer at the bottom of the filter which will

result in damage to the bottom strainer or at least inefficient operation. Plus you may have to remove all

of the sand to get it unclogged.

 Let filtration system run dry (without water)! If your pump runs dry too long non-warranty damage to the

pump may occur. Damage to the pump caused by dry running is NOT covered by the warranty.

R. Trouble Shooting - See the expanded FlowXtreme Prime Pump Trouble Shooting section after the

Technical Data at the end of this manual. Additional information is provided in Section W.

Malfunction Cause Solution

Pressure gauge has reading

more than 10 PSI over the

normal filtering pressure

Dirty filter bed Backwash the filter (position 4)

Pressure is too low Hair and lint strainer basket is

dirty; Pump gets too little

water

Clean the hair and lint strainer; check the suction

line and the water level

Air in the pump Poor seal on the intake side of

pump

Tighten hose clamps and connecting fittings

Leaking filter Seal Defective Check the seal, replace if needed

Pump does not run Not plugged in Check the socket and power cord

G.F.C.I./ or main circuit

breaker tripped

Switch on the breaker. If it is immediately

tripped again, there may be a defect in pump,

pump controls, GFCI or the breaker

Pump motor defective Have the electrical system checked by a licensed

electrical professional or replace motor or entire

pump

Sand in Pool If the sand is newly replaced,

the undersized grains are still

present

Backwash several times until the backwash water

is clear (position 4)

Sand in Central Valve (from

backwash)

Purge into drainpipe for 30 seconds (position 6)

Filter bottom strainer is

damaged

Replace the filter bottom strainer

Air in system Loosen, but do not re-move, one of the clear

view port covers on the top of the filter tank to

allow any trapped air to escape. Tighten the

cover once all of the air has escaped.

S. Instal

ation an

Operat

on Illust

ation Fi

ures

T. FlowXtrem 16" AG SYSTEM NE4487/4488/4489 PARTS BREAKDOWN

AND DIAGRAMS

Key Part Name Qty Mnfg. No. B.W. No. For Model#

1 Valve Handle 1 V00152 NEP4289 NE4487/4488/4489

2 Valve Stem Pin 1 V00153 NEP4290 NE4487/4488/4489

3 Valve Cover 1 V00154 NEP4291 NE4487/4488/4489

4 Diverter Stem Spool 1 V00155 NEP4292 NE4487/4488/4489

5 Diverter Stem Gasket 1 V00156 NEP4293 NE4487/4488/4489

6 Diverter Stem Spring 1 V00157 NEP4294 NE4487/4488/4489

7 Diverter 1

V00126

NEP4287 NE4487/4488/4489

8 Diverter Gasket 1 NEP4287 NE4487/4488/4489

9 Valve Cover Seal 1 V00158 NEP4295 NE4487/4488/4489

10 Pressure Gauge 1 G00114 NEP4184 NE4487/4488/4489

11 Tank Cover 1 T00159 NEP4283 NE4487/4488/4489

12 Long INTEX Connector 1 I00160 NEP4233 NE4487/4488/4489

13 Flat Gasket For INTEX Connector 2 I00161 NEP4234 NE4487/4488/4489

14 Short INTEX Connector 1 I00162 NEP4235 NE4487/4488/4489

15 1 1/4" O-Ring For Long INTEX Connector 1 I00163 NEP4236 NE4487/4488/4489

16 View Port Cover 2 T00164 NEP4284 NE4487/4488/4489

17 Gasket For View Port Cover 2 T00165 NEP4285 NE4487/4488/4489

18 Seal Washer For Valve Cover Stems 9 V00166 NEP4296 NE4487/4488/4489

19 Valve Cover Screws 9 V00167 NEP4297 NE4487/4488/4489

20 Tank Seal 1 T00168 NEP4286 NE4487/4488/4489

21 Upper Distributor 1 T00116 NEP4273 NE4487/4488/4489

Lock Ring Pin

TANK COVER LOCK RING ASSEMBLY

1 L00169 NEP4237 NE4487/4488/4489

Left Side Lock Ring

TANK COVER LOCK RING ASSEMBLY

1 L00170 NEP4238 NE4487/4488/4489

Right Side Lock Ring

TANK COVER LOCK RING ASSEMBLY

1 L00171 NEP4239 NE4487/4488/4489

Lock Ring Bolt

TANK COVER LOCK RING ASSEMBLY

1 L00172 NEP4240 NE4487/4488/4489

Lock Ring Knob

TANK COVER LOCK RING ASSEMBLY

1 L00173 NEP4241 NE4487/4488/4489

27 Tank Separator Plate 1025 1 T00117 NEP4274 NE4487

27 Tank Separator Plate 1050 1 T00118 NEP4275 NE4488

27 Tank Separator Plate 1075 1 T00119 NEP4276 NE4489

28 Tank Bottom Strainer 1 T00120 NEP4277 NE4487/4488/4489

29 Filter Tank 1025 1 T00121 NEP4278 NE4487

29 Filter Tank 1050 1 T00122 NEP4279 NE4488

29 Filter Tank 1075 1 T00123 NEP4280 NE4489

30 Drain Cap 1 T00124 NEP4281 NE4487/4488/4489

31 Drain Cap Gasket 1 T00125 NEP4282 NE4487/4488/4489

32 Filter Pump Hose 1025 (W/Screw Head) 1 P00127 NEP4242 NE4487

32 Filter Pump Hose 1050 1 P00128 NEP4243 NE4488

32 Filter Pump Hose 1075 1 P00129 NEP4244 NE4489

33 Hose Clamp 1 P00174 NEP4260 NE4487

33 Hose Clamp 2 P00174 NEP4260 NE4488/4489

Pump Bolt Wing Nut

PUMP MOUNTING HARDWARE

2 P00175 NEP4261 NE4487/4488/4489

Pump Bolt Flat Water

PUMP MOUNTING HARDWARE

2 P00176 NEP4262 NE4487/4488/4489

Pump Bolt Lock Washer

PUMP MOUNTING HARDWARE

2 P00177 NEP4263 NE4487/4488/4489

Pump Bolt Nut

PUMP MOUNTING HARDWARE

2 P00178 NEP4264 NE4487/4488/4489

38 Base Plate 1 B00130 NEP4183 NE4487/4488/4489

39 Stainless Steel Gasket 2 V00185 NEP4298 NE4487/4488/4489

40 Spring Seat 1 V00186 NEP4299 NE4487/4488/4489

Hose Reducer 1 P00179 NEP4090 NE4487

Hose Reducer 2 P00179 NEP4090 NE4488/4489

U. TECHNICAL DATA for FlowXtreme Prime Single Speed Pump

Model #s; NE4523, NEP4268, NEP4269, NE4524, NEP4271

Technical Data

FlowXtreme PRIME, SPS1 Pumps Parts Breakdown & Diagram

Key Part Name Qty Mnfg. No. B.W. No. For Model#

1 Water Pump/ Motor 250 W 1 SPS1A250 NEP4268 NEP4268

1 Water Pump/ Motor 450 W 1 SPS1A450 NEP4269 NEP4269

1 Water Pump/ Motor 550 W 1 SPS1A550 NE4523 NE4523

Transparent Hair & Lint Strainer

Cover

1 P00131 NEP4245 NEP4268/NEP4269/NE4523

3 1 1/4"- 1 1/2" Hose Connector 2 P00132 NEP4246 NEP4268/NEP4269/NE4523

4 O-ring "A"- 2 1/4" 1 P00182 NEP4265 NEP4268/NEP4269/NE4523

5 O-ring "B"- 3" 1 P00183 NEP4266 NEP4268/NEP4269/NE4523

6 O-ring "C"- 1.5" 1 P00184 NEP4267 NEP4268/NEP4269/NE4523

7 Strainer Collar 1 P00133 NEP4247 NEP4268/NEP4269/NE4523

8 Strainer Basket 1 P00134 NEP4248 NEP4268/NEP4269/NE4523

9 Pump Drain Cap 1 P00135 NEP4249 NEP4268/NEP4269/NE4523

10 Drain Valve O-ring 1 P00136 NEP4250 NEP4268/NEP4269/NE4523

11 Motor Pump Seal - 250 1 P00137 NEP4251 NEP4268/NEP4269/NE4523

11 Motor Pump Seal - 450 1 P00138 NEP4252 NEP4268/NEP4269/NE4523

11 Motor Pump Seal - 550 1 P00138 NEP4252 NEP4268/NEP4269/NE4523

12 Impeller Assembly - 250 1 P001392 NEP4253 NEP4268

12 Impeller Assembly - 450 1 P001404 NEP4254 NEP4269

12 Impeller Assembly - 550 1 P001405 NEP20200 NE4523

13 Shaft Seal & Spring Assbly – 250 1 P00141 NEP4255 NEP4268/NEP4269/NE4523

13 Shaft Seal & Spring Assbly - 450 1 P00142 NEP4256 NEP4268/NEP4269/NE4523

13 Shaft Seal & Spring Assbly - 550 1 P00142 NEP4256 NEP4268/NEP4269/NE4523

14 Power Cord With 3 Prong Plug 1 P00143 NEP20201 NEP4268/NEP4269/NE4523

Model HP Voltage Hertz Amps Flow Rate GPM

NE4523 0.75 115 60 5.5 38GPM

NEP4268 0.33 115 60 2.5 24GPM

NEP4269 0.50 115 60 4.5 35GPM

NE4524 1.50 115 60 15.5 115GPM

NEP4271 1.0 115 60 11.0 90GPM

Key

lowXtre

Water Pu

Valve Bod

Connector

Pump Con

Strainer B

O-Sealing

Transpare

Circumgyr

Drain Val

Pump Dra

Basket Co

Power Cor

Motor Pu

Impeller

Shaft Seal

e PRIM

art Name

O-Ring

ecto

ector Nu

ske

ing

t Cove

ate Cove

e O-Ring

n Valve

er Closing T

d with 3 pron

p Seal

ssembly - 11

ssembly - 16

& Spring As

, SPS3

odel #s

;

ol 1

plug 1

0 1

embly 1

umps P

;

NEP42

Mnf

SPS3

3029

3030

3031

3032

3033

3034

3035

3036

3037

3038

3039

3040

3041

3042

3043

3044

rts Brea

1, NE45

No. B.

100

600

down &

. No.

4271

4254

4128

4129

4130

4131

4132

4133

4134

4135

4136

4137

20202

20203

20204

20205

20206

20207

Dia

For Mode

EP427

NE4524

EP4271 & N

EP4271 &

EP4271 & N

NEP4271

NE4524

EP4271 & N

4524

V. Trou

Motor W

Make sure t

for available

1. Impr

Solutio

2. Man

3. If yo

Motor Sh

1. Low

Solutio

2. Mot

Solutio

NOTE

leshooti

ll NOT St

e terminal b

field supply

oper or loose

n: Check all

ally check r

have a time

ts OFF –

voltage at m

n: Contact q

r may be ove

n: Check wa

- Your pump

for an

rt – Chec

ard connecti

oltage (see p

wiring conne

onnections,

tation of mot

, be certain i

heck For

tor or power

alified profe

rheating due

er flow to ins

motor is equ

FlowXt

For:

ns agree wit

mp operatin

tions; open

ircuit breake

r shaft for fr

is working p

drop (freque

sional to che

o direct sunli

re uniform a

pped with an

eme Pri

the wiring d

label).

witches or re

s, and fuses.

e movement

roperly. Byp

tly caused by

k that the wi

ght or low w

mount of wa

“automatic t

e Pum

agram on mo

ays; tripped

eset tripped

and lack of o

ss it if necess

undersized

ing gauge is

ter level in t

er coming to

ermal overlo

or data plate

ircuit breake

breakers or r

struction.

ary.

iring or exte

eavy enough

e pump bask

he pump.

d protector.”

label. Be sur

s, GFCI’s, o

place blown

sion cord us

”

The motor

motor is wir

blown fuses.

fuses.

ill

automatically shut off if power supply drops before heat damage can build up causing windings to burn out. The

“thermal overload protector” will allow the motor to automatically restart once the motor has cooled. It will continue

to shut off until the problem is corrected. Be sure to correct cause of overheating.

Motor Hums, But Does NOT Start – Check For:

1. Impeller jammed with debris.

Solution: Have a qualified repair professional open the pump and remove the debris.

2. Motor is frozen either form months in the carton after manufacturing or from over winter storage.

Solution: Insert a flat bladed screw driver into the slot at the back end of the motor shaft and turn motor shaft until it

moves freely. You may have to remove the protective metal cap from some models to access the motor shaft.

NOTE – All FlowXtreme & FX PRO II pumps are run tested with water before leaving the factory.

Pump Won't Prime - Check For:

1. Empty pump/strainer housing

Solution: Make sure pump/strainer housing is filled with water and cover o-ring is clean. Ensure o-ring is properly

seated in the cover o-ring groove. Ensure o-ring is lubricated and that strainer cover is locked firmly in position.

Lubricant will help to create a tighter seal.

2. Loose connections on suction side.

Solution: Tighten pipe/union connections or hose clamps on flexible hose.

NOTE - Any self-priming pump will not prime if there are suction air leaks. Leaks will result in bubbles emanating

from return fittings on In Ground pool wall.

3. Leaking O-ring on valves.

Solution: Tighten, repair, or replace valves.

4. Strainer basket or skimmer basket loaded with debris.

Solution: Remove strainer housing cover or skimmer cover, clean basket, and refill strainer housing with water.

Tighten cover.

Low Flow – Generally, Check For:

1. Clogged or restricted strainer or suction line.

Solution: Check for visible debris and remove if observed. If the problem continues contact a qualified repair

professional.

2. Undersized pool plumbing.

Solution: Correct plumbing size.

3. Plugged or restricted discharge line of filter, valve partially closed (high gauge reading).

Solution: Sand filters – backwash as per manufacturer’s instructions; D.E. filters – backwash as per manufacturer’s

instructions; Cartridge filters – clean or replace cartridge.

4. Air leak in suction (bubbles issuing from return fittings).

Solution: Re-tighten suction and discharge connections using Teflon tape. Inspect other plumbing connections and

tighten as required.

5. Plugged, restricted, or damaged impeller.

Solution: Contact a qualified repair professional to install a new impeller & seal assembly.

Noisy Pump – Check For:

1. Air leak in suction piping, cavitation caused by restricted or undersized suction line or leak at any joint, low water

level in pool, and unrestricted discharge return lines.

Solution: Correct suction condition or tighten fittings, if practical. Holding hand over return fitting will sometimes

prove this point or putting in a smaller return eyeball fitting.

2. Vibration due to improper mounting, etc.

Solution: Mount the pump on a level surface and secure the pump to the equipment pad.

3. Foreign matter in pump housing. Loose stones/debris hitting impeller will cause noise.

Solution: With the pump turned off or disconnected from the power source clean the pump housing and inspect to

remove any debris visible in the inner portion of the pump by the impeller.

4. Motor bearings noisy from normal wear, rust, overheating, or concentration of chemicals causing seal damage.

This will allow chlorinated water to seep into bearings wiping out the grease resulting in rusting of the motor shaft

and causing the bearing to whine.

Solution: All seal leaks must be replaced at once. Have a qualified pump repair specialist replace the motor shaft

seals and inspect the motor shaft for possible damage. If the motor shaft is damaged replace the motor.

Water Leaks Around Intake and Discharge fittings – Check For

1. Lose union fittings or hose fittings.

Solution: Tighten fittings or remove, apply Teflon tape and reinstall.

2. Lose hose clamps on flexible hose.

Solution: Tighten hose clamps using a nut driver or wrench instead of a screwdriver

3. Leaks that continue after trying the above solutions.

Solution: Inspect union fittings and hose fittings for excess plastic mold flashing that can cause hoses and plumbing

not to seal. If plastic mold flashing is found remove it with a fine tooth file or knife blade and re-assemble. If the

fitting still will not seal replace them and reassemble plumbing with the new fittings.

ATTENTION

DO NOT RETURN THIS PRODUCT TO YOUR RETAILER. IF

YOU ENCOUNTER ANY DIFFICULTIES WITH YOUR NEW

SWIMMING POOL PUMP CONTACT BLUE WAVE CUSTOMER

SERVICE FOR ASSISTANCE.

1-800-759-0977

W. Warranty Information

This product is warranted to the original purchaser to be free from defects in material or workmanship for a

period of one (1) year from the date of the original retail purchase.

This warranty does not cover defects or damage due to improper installation, alteration, accident or any other

event beyond the control of the manufacturer. Defects or damage resulting from misuse, abuse or negligence

will void this warranty. This warranty does not cover scratching or damage that may result from normal usage.

This product is not intended for institutional or commercial use; the manufacturer does not assume any

liability for such use. Institutional or commercial use will void this warranty.

This warranty is nontransferable and is expressly limited to the repair or replacement of the defective product.

During the warranty period, the manufacturer shall repair or replace defective parts at no cost to the purchaser.

Shipping charges and insurance are not covered and are the responsibility of the purchaser. Labor charges and

related expenses for removal, installation or replacement of the product or components are not covered under

this warranty.

The manufacturer reserves the right to make substitutions to warranty claims if parts are unavailable or

obsolete.

The manufacturer shall not be liable for loss of use of the product or other consequential or incidental costs,

expenses or damages incurred by the consumer of any other use. The user assumes all risk of injury resulting

from the use of this product.

This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of

merchantability or fitness for use to the extent permitted by Federal or state law. Neither the manufacturer nor

any of its representatives assumes any other liability in connection with this product.

All warranty claims must include the retailer’s information where the product was originally purchased.

A purchase receipt or other proof of date of purchase will be required to process all warranty claims.

The model number and part numbers found within the assembly instructions will be required when

submitting any parts requests or warranty claims.

For further warranty information or inquiries, please call 1 (800) 759-0977 Or email

warranty@splashnetxpress.com

Blue Wave Products, Inc.

1745 Wallace Ave, Suite B

Saint Charles, IL 60174

La garantie du produit est valide pour l'acheteur original en ce qui a trait aux pièces défectueuses ou à la

main-d’œuvre pour une période de 1 année de la date d’achat.

Cette garantie n’est couvre pas les dommages causés par accident, par modification, par une installation

défectueuse ou tout autre événement hors du contrôle du fabricant. Tout défaut ou dommage résultant de la

négligence ou d’une mauvaise utilisation annule cette garantie. La présente garantie ne couvre pas les

égratignures ou les dommages attribuables à un usage normal.

Ce produit n'est pas destiné à un usage institutionnel ou commercial; le fabricant décline toute responsabilité

pour une telle utilisation. Un usage institutionnel ou commercial annule cette garantie.

Cette garantie est non transférable et est expressément limitée à la réparation ou au remplacement du produit

défectueux. Au cours de la période de garantie, le fabricant s’engage à remplacer et à réparer les pièces

défectueuses sans frais pour l’acheteur. Les frais d’assurance et d'expédition ne sont pas couverts et sont à la

charge de l'acheteur. Les frais de main-d'œuvre et les dépenses liées au déplacement, à l’installation ou au

remplacement du produit ou de ses composantes ne sont pas couverts par cette garantie.

Le fabricant se réserve le droit de faire des substitutions de recours en garantie si la pièce n'est pas disponible

ou obsolète.

Le fabricant décline toute responsabilité liée à la perte d'utilisation ainsi que tous les autres coûts directs ou

indirects, frais ou dommages encourus par le consommateur qui aurait été causés par une autre utilisation.

L'utilisateur assume tous les risques de dommage résultant de l'utilisation de ce produit.

Cette garantie tient lieu expressément de toute autre garantie, exprimée ou implicite, y compris les garanties de

qualité marchande ou d'adaptation à un emploi particulier dans la mesure permise par les lois fédérales ou

provinciales. Ni le fabricant, ni aucun de ses représentants n'assument aucune autre responsabilité en rapport

avec ce produit.

Toute réclamation doit être faite par le détaillant où le produit a été acheté. Une facture ou autre preuve

d'achat est nécessaire pour traiter toutes les réclamations de garantie. Le numéro de modèle et les

numéros de référence figurant dans les instructions d'assemblage seront exigés lors de la soumission de

demande de pièces ou de recours en garantie.

Pour plus d’information ou pour toute question, veuillez téléphoner au 1 (800) 759-0977 ou email

warranty@splashnetxpress.com

Blue Wave Products, Inc.

1745 Wallace Ave, Suite B

Saint Charles, IL 60174

Bluewave NE4488 Manuel utilisateur

Marque: Bluewave

Modèle: NE4488

Catégorie: Accessoires de piscine hors terre

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Bluewave NE4488 User manual

Bluewave NE4488 Manuel utilisateur

Ce manuel convient également à

Bluewave NE4488 Manuel utilisateur

dans d''autres langues

Autres documents