Bestway 58486 Le manuel du propriétaire

Marque: Bestway

Modèle: 58486

Taper: Le manuel du propriétaire

OWNER’S MANUAL

bestwaycorp.com/support

Visit Bestway YouTube channel

58486 Hmax 1.5 m

WE SUGGEST NOT TO RETURN

THE PRODUCT TO THE STORE

QUESTIONS? PROBLEMS?

MISSING PARTS?

For FAQ, Manuals, Videos Or

Spare Parts, Please Visit

bestwaycorp.com/support

WARNING

IMPORTANT SAFETY INSTRUCTIONS - READ AND FOLLOW

ALL SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

When installing and using this electrical equipment, basic safety

precautions should always be followed, including the following:

• The pump is to be supplied by an isolating transformer or supplied

through a residual current device (RCD)having a rated residual

operating current not exceeding 30 mA.

• The power source on the wall of building should keep more than

4m away from pool.

• The appliance must be supplied by earthed power source.

• RISK OF ELECTRIC SHOCK - The pump cannot be using while

people are inside the pool. Forbid the access of the pool in case of

damage of the sand filter.

• DO NOT BURY CORD. Locate cord to minimize abuse from lawn

mowers, hedge trimmers, and other equipment.

• To reduce the risk of electric shock, replace damaged cord immediately.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons in

order to avoid a hazard.

• Extension cords can’t be used.

• Risk of electric shock. Using the sand filter with an unmatched electrical

supply is dangerous and will permanently damage the sand filter.

• Do not remove the grounding prong or modify the plug in anyway.

Do not use adaptor plugs. Consult a qualified electrician for any

questions relating to validity of your plugs or grounding.

• Handle the sand filter with care. Do not pull or carry the sand filter

by the power cord. Never pull a plug from the outlet by yanking the

power cord. Keep cord free from abrasions. Sharp objects, oil,

moving parts, and heat should never be exposed to the sand filter.

• Always unplug this product from the electrical outlet before removing,

cleaning, servicing or making any adjustment to the product.

• Don’t plug or unplug the appliance if hand is wet.

• Always unplug the appliance:

• On raining days

• Before cleaning or other maintenance

• Leave it unattended on holidays

• When the appliance will be not used for long time, such as in the

winter, the pool set should be disassembled and stored indoor.

• CAUTION: Read the instruction before using the appliance and

installation/reassembly every time.

• Safekeeping the instruction. For reconstruction the pool set every

time, please always refer to the instructions.

• If instruction is missed, please contact with Bestway or search it in

website: www.bestwaycorp.com

• Electric installations should follow national wiring rules. Consult a

qualified electrician for any questions.

CAUTION: This sand filter is for use with storable pools only. Do

not use with permanently-installed pools. A storable pool is

constructed so that it is capable of being readily disassembled for

storage and reassembled to its original integrity. A

permanently-installed pool is constructed in or on the ground or in

a building such that it cannot be readily disassembled for storage.

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in

a safe way and understand the hazards involved. Children shall not

play with the appliance. Cleaning and user maintenance shall not

be made by children without supervision.

• Cleaning and user maintenance must be performed by an adult

above 18 years old who is familiar with the risk of electric shock.

NOTES:

• Place the sand filter on solid, level ground. Ensure the sand filter is

at least 3.5 meters away from poolside. Keep distance as far as possible.

• Pay attention to position pool and sand filter so adequate

ventilation, drainage, and access for maintenance is available.

Never place the filter in an area that may accumulate water, or on a

walking path with lots of foot traffic.

• It is necessary to have the plug accessible after

installation of the pool. The plug of the sand

filter shall be at least 3.5m away from the pool.

• Atmospheric conditions may affect the

performance and life span of the sand filter;

take adequate precautions to protect the sand

filter from unnecessary wear and tear that may

occur during periods of cold or hot weather

and/or exposure to sun.

• Please examine and verify all sand filter components are present

before use. Notify Bestway at the customer service address listed on

this manual for any damaged or missing parts at the time of purchase.

• It is imperative to change as soon as possible all deteriorated

parts. Only use parts approved by the manufacturer.

• Do not allow children or adults to lean or sit on the apparatus.

• Do not add chemicals to the sand filter.

• When chemical products are used to clean the pool water, it is

recommended to respect a minimum filtration time to preserve the

health of swimmers which depends on compliance of health regulation.

• Only the media provided or specified by the manufacturer is to be

used with product installation.

• It is essential to check that the suction openings are not obstructed.

• It is advisable to stop the filtration during maintenance operations

on the filtration system.

• Regularly monitor the filter clogging level.

• A weekly check is recommended for backwashing or cleaning.

Minimum daily filtration operating time of 8 hours is recommended

to ensure clear pool water.

• It is essential to change any damaged element or set of elements

as soon as possible. Use only parts approved by person

responsible for placing the product on the market.

• All filters and filter media shall be inspected regularly to ensure that

there is not a build-up of detritus thus preventing good filtration.

The disposal of any used filter media should also be in accordance

with applicable regulations/legislation.

• Mind all the safety requirements and recommendations described

in the manual. In case of doubt on the pump or any circulation

devices, contact a qualified installer, or the

manufacturer/importer/distributor. The water circulation installation

shall comply with the European as well as national/local

regulations, especially when dealing with electrical issues. Any

change of valve position, pump size, grille size can cause a change

of the flow and the suction velocity can be increased.

• This product is not intended for commercial use.

PLEASE READ THE INSTRUCTION MANUAL CAREFULLY AND

KEEP IT FOR FUTURE REFERENCE.

SAVE THESE INSTRUCTIONS

RCD WARNING

WARNING: Before inserting plug into a power outlet, make

sure the current rate of the power outlet is suitable for the sand

filter.

WARNING: Risk of electric shock. The RCD plug must be

tested before each use.

WARNING: Insert the RCD plug into a residual current device

(RCD) having a rated residual operating not exceeding 30 mA.

WARNING: Do not use the sand filter if this test fails. For

assistance, please visit the support section on our website,

www.bestwaycorp.com.

SAND FILTER

OWNER’S MANUAL

WE SUGGEST NOT TO RETURN

THE PRODUCT TO THE STORE

QUESTIONS? PROBLEMS?

MISSING PARTS?

For FAQ, Manuals, Videos Or

Spare Parts, Please Visit

bestwaycorp.com/support

SAFETY INSTRUCTIONS

Visit Bestway YouTube

channel

WARNING

IMPORTANT SAFETY INSTRUCTIONS - READ AND FOLLOW

ALL SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

When installing and using this electrical equipment, basic safety

precautions should always be followed, including the following:

• The pump is to be supplied by an isolating transformer or supplied

through a residual current device (RCD)having a rated residual

operating current not exceeding 30 mA.

• The power source on the wall of building should keep more than

4m away from pool.

• The appliance must be supplied by earthed power source.

• RISK OF ELECTRIC SHOCK - The pump cannot be using while

people are inside the pool. Forbid the access of the pool in case of

damage of the sand filter.

• DO NOT BURY CORD. Locate cord to minimize abuse from lawn

mowers, hedge trimmers, and other equipment.

• To reduce the risk of electric shock, replace damaged cord immediately.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons in

order to avoid a hazard.

• Extension cords can’t be used.

• Risk of electric shock. Using the sand filter with an unmatched electrical

supply is dangerous and will permanently damage the sand filter.

• Do not remove the grounding prong or modify the plug in anyway.

Do not use adaptor plugs. Consult a qualified electrician for any

questions relating to validity of your plugs or grounding.

• Handle the sand filter with care. Do not pull or carry the sand filter

by the power cord. Never pull a plug from the outlet by yanking the

power cord. Keep cord free from abrasions. Sharp objects, oil,

moving parts, and heat should never be exposed to the sand filter.

• Always unplug this product from the electrical outlet before removing,

cleaning, servicing or making any adjustment to the product.

• Don’t plug or unplug the appliance if hand is wet.

• Always unplug the appliance:

• On raining days

• Before cleaning or other maintenance

• Leave it unattended on holidays

• When the appliance will be not used for long time, such as in the

winter, the pool set should be disassembled and stored indoor.

• CAUTION: Read the instruction before using the appliance and

installation/reassembly every time.

• Safekeeping the instruction. For reconstruction the pool set every

time, please always refer to the instructions.

• If instruction is missed, please contact with Bestway or search it in

website: www.bestwaycorp.com

• Electric installations should follow national wiring rules. Consult a

qualified electrician for any questions.

CAUTION: This sand filter is for use with storable pools only. Do

not use with permanently-installed pools. A storable pool is

constructed so that it is capable of being readily disassembled for

storage and reassembled to its original integrity. A

permanently-installed pool is constructed in or on the ground or in

a building such that it cannot be readily disassembled for storage.

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in

a safe way and understand the hazards involved. Children shall not

play with the appliance. Cleaning and user maintenance shall not

be made by children without supervision.

• Cleaning and user maintenance must be performed by an adult

above 18 years old who is familiar with the risk of electric shock.

NOTES:

• Place the sand filter on solid, level ground. Ensure the sand filter is

at least 3.5 meters away from poolside. Keep distance as far as possible.

• Pay attention to position pool and sand filter so adequate

ventilation, drainage, and access for maintenance is available.

Never place the filter in an area that may accumulate water, or on a

walking path with lots of foot traffic.

• It is necessary to have the plug accessible after

installation of the pool. The plug of the sand

filter shall be at least 3.5m away from the pool.

• Atmospheric conditions may affect the

performance and life span of the sand filter;

take adequate precautions to protect the sand

filter from unnecessary wear and tear that may

occur during periods of cold or hot weather

and/or exposure to sun.

• Please examine and verify all sand filter components are present

before use. Notify Bestway at the customer service address listed on

this manual for any damaged or missing parts at the time of purchase.

• It is imperative to change as soon as possible all deteriorated

parts. Only use parts approved by the manufacturer.

• Do not allow children or adults to lean or sit on the apparatus.

• Do not add chemicals to the sand filter.

• When chemical products are used to clean the pool water, it is

recommended to respect a minimum filtration time to preserve the

health of swimmers which depends on compliance of health regulation.

• Only the media provided or specified by the manufacturer is to be

used with product installation.

• It is essential to check that the suction openings are not obstructed.

• It is advisable to stop the filtration during maintenance operations

on the filtration system.

• Regularly monitor the filter clogging level.

• A weekly check is recommended for backwashing or cleaning.

Minimum daily filtration operating time of 8 hours is recommended

to ensure clear pool water.

• It is essential to change any damaged element or set of elements

as soon as possible. Use only parts approved by person

responsible for placing the product on the market.

• All filters and filter media shall be inspected regularly to ensure that

there is not a build-up of detritus thus preventing good filtration.

The disposal of any used filter media should also be in accordance

with applicable regulations/legislation.

• Mind all the safety requirements and recommendations described

in the manual. In case of doubt on the pump or any circulation

devices, contact a qualified installer, or the

manufacturer/importer/distributor. The water circulation installation

shall comply with the European as well as national/local

regulations, especially when dealing with electrical issues. Any

change of valve position, pump size, grille size can cause a change

of the flow and the suction velocity can be increased.

• This product is not intended for commercial use.

PLEASE READ THE INSTRUCTION MANUAL CAREFULLY AND

KEEP IT FOR FUTURE REFERENCE.

SAVE THESE INSTRUCTIONS

RCD WARNING

WARNING: Before inserting plug into a power outlet, make

sure the current rate of the power outlet is suitable for the sand

filter.

WARNING: Risk of electric shock. The RCD plug must be

tested before each use.

WARNING: Insert the RCD plug into a residual current device

(RCD) having a rated residual operating not exceeding 30 mA.

WARNING: Do not use the sand filter if this test fails. For

assistance, please visit the support section on our website,

www.bestwaycorp.com.

WARNING

IMPORTANT SAFETY INSTRUCTIONS - READ AND FOLLOW

ALL SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

When installing and using this electrical equipment, basic safety

precautions should always be followed, including the following:

• The pump is to be supplied by an isolating transformer or supplied

through a residual current device (RCD)having a rated residual

operating current not exceeding 30 mA.

• The power source on the wall of building should keep more than

4m away from pool.

• The appliance must be supplied by earthed power source.

• RISK OF ELECTRIC SHOCK - The pump cannot be using while

people are inside the pool. Forbid the access of the pool in case of

damage of the sand filter.

• DO NOT BURY CORD. Locate cord to minimize abuse from lawn

mowers, hedge trimmers, and other equipment.

• To reduce the risk of electric shock, replace damaged cord immediately.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons in

order to avoid a hazard.

• Extension cords can’t be used.

• Risk of electric shock. Using the sand filter with an unmatched electrical

supply is dangerous and will permanently damage the sand filter.

• Do not remove the grounding prong or modify the plug in anyway.

Do not use adaptor plugs. Consult a qualified electrician for any

questions relating to validity of your plugs or grounding.

• Handle the sand filter with care. Do not pull or carry the sand filter

by the power cord. Never pull a plug from the outlet by yanking the

power cord. Keep cord free from abrasions. Sharp objects, oil,

moving parts, and heat should never be exposed to the sand filter.

• Always unplug this product from the electrical outlet before removing,

cleaning, servicing or making any adjustment to the product.

• Don’t plug or unplug the appliance if hand is wet.

• Always unplug the appliance:

• On raining days

• Before cleaning or other maintenance

• Leave it unattended on holidays

• When the appliance will be not used for long time, such as in the

winter, the pool set should be disassembled and stored indoor.

• CAUTION: Read the instruction before using the appliance and

installation/reassembly every time.

• Safekeeping the instruction. For reconstruction the pool set every

time, please always refer to the instructions.

• If instruction is missed, please contact with Bestway or search it in

website: www.bestwaycorp.com

• Electric installations should follow national wiring rules. Consult a

qualified electrician for any questions.

CAUTION: This sand filter is for use with storable pools only. Do

not use with permanently-installed pools. A storable pool is

constructed so that it is capable of being readily disassembled for

storage and reassembled to its original integrity. A

permanently-installed pool is constructed in or on the ground or in

a building such that it cannot be readily disassembled for storage.

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in

a safe way and understand the hazards involved. Children shall not

play with the appliance. Cleaning and user maintenance shall not

be made by children without supervision.

• Cleaning and user maintenance must be performed by an adult

above 18 years old who is familiar with the risk of electric shock.

NOTES:

• Place the sand filter on solid, level ground. Ensure the sand filter is

at least 3.5 meters away from poolside. Keep distance as far as possible.

• Pay attention to position pool and sand filter so adequate

ventilation, drainage, and access for maintenance is available.

Never place the filter in an area that may accumulate water, or on a

walking path with lots of foot traffic.

• It is necessary to have the plug accessible after

installation of the pool. The plug of the sand

filter shall be at least 3.5m away from the pool.

• Atmospheric conditions may affect the

performance and life span of the sand filter;

take adequate precautions to protect the sand

filter from unnecessary wear and tear that may

occur during periods of cold or hot weather

and/or exposure to sun.

• Please examine and verify all sand filter components are present

before use. Notify Bestway at the customer service address listed on

this manual for any damaged or missing parts at the time of purchase.

• It is imperative to change as soon as possible all deteriorated

parts. Only use parts approved by the manufacturer.

• Do not allow children or adults to lean or sit on the apparatus.

• Do not add chemicals to the sand filter.

• When chemical products are used to clean the pool water, it is

recommended to respect a minimum filtration time to preserve the

health of swimmers which depends on compliance of health regulation.

• Only the media provided or specified by the manufacturer is to be

used with product installation.

• It is essential to check that the suction openings are not obstructed.

• It is advisable to stop the filtration during maintenance operations

on the filtration system.

• Regularly monitor the filter clogging level.

• A weekly check is recommended for backwashing or cleaning.

Minimum daily filtration operating time of 8 hours is recommended

to ensure clear pool water.

• It is essential to change any damaged element or set of elements

as soon as possible. Use only parts approved by person

responsible for placing the product on the market.

• All filters and filter media shall be inspected regularly to ensure that

there is not a build-up of detritus thus preventing good filtration.

>3.5 m

POOL

The disposal of any used filter media should also be in accordance

with applicable regulations/legislation.

• Mind all the safety requirements and recommendations described

in the manual. In case of doubt on the pump or any circulation

devices, contact a qualified installer, or the

manufacturer/importer/distributor. The water circulation installation

shall comply with the European as well as national/local

regulations, especially when dealing with electrical issues. Any

change of valve position, pump size, grille size can cause a change

of the flow and the suction velocity can be increased.

• This product is not intended for commercial use.

PLEASE READ THE INSTRUCTION MANUAL CAREFULLY AND

KEEP IT FOR FUTURE REFERENCE.

SAVE THESE INSTRUCTIONS

RCD WARNING

WARNING: Before inserting plug into a power outlet, make

sure the current rate of the power outlet is suitable for the sand

filter.

WARNING: Risk of electric shock. The RCD plug must be

tested before each use.

WARNING: Insert the RCD plug into a residual current device

(RCD) having a rated residual operating not exceeding 30 mA.

WARNING: Do not use the sand filter if this test fails. For

assistance, please visit the support section on our website,

www.bestwaycorp.com.

WARNING

IMPORTANT SAFETY INSTRUCTIONS - READ AND FOLLOW

ALL SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

When installing and using this electrical equipment, basic safety

precautions should always be followed, including the following:

• The pump is to be supplied by an isolating transformer or supplied

through a residual current device (RCD)having a rated residual

operating current not exceeding 30 mA.

• The power source on the wall of building should keep more than

4m away from pool.

• The appliance must be supplied by earthed power source.

• RISK OF ELECTRIC SHOCK - The pump cannot be using while

people are inside the pool. Forbid the access of the pool in case of

damage of the sand filter.

• DO NOT BURY CORD. Locate cord to minimize abuse from lawn

mowers, hedge trimmers, and other equipment.

• To reduce the risk of electric shock, replace damaged cord immediately.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons in

order to avoid a hazard.

• Extension cords can’t be used.

• Risk of electric shock. Using the sand filter with an unmatched electrical

supply is dangerous and will permanently damage the sand filter.

• Do not remove the grounding prong or modify the plug in anyway.

Do not use adaptor plugs. Consult a qualified electrician for any

questions relating to validity of your plugs or grounding.

• Handle the sand filter with care. Do not pull or carry the sand filter

by the power cord. Never pull a plug from the outlet by yanking the

power cord. Keep cord free from abrasions. Sharp objects, oil,

moving parts, and heat should never be exposed to the sand filter.

• Always unplug this product from the electrical outlet before removing,

cleaning, servicing or making any adjustment to the product.

• Don’t plug or unplug the appliance if hand is wet.

• Always unplug the appliance:

• On raining days

• Before cleaning or other maintenance

• Leave it unattended on holidays

• When the appliance will be not used for long time, such as in the

winter, the pool set should be disassembled and stored indoor.

• CAUTION: Read the instruction before using the appliance and

installation/reassembly every time.

• Safekeeping the instruction. For reconstruction the pool set every

time, please always refer to the instructions.

• If instruction is missed, please contact with Bestway or search it in

website: www.bestwaycorp.com

• Electric installations should follow national wiring rules. Consult a

qualified electrician for any questions.

CAUTION: This sand filter is for use with storable pools only. Do

not use with permanently-installed pools. A storable pool is

constructed so that it is capable of being readily disassembled for

storage and reassembled to its original integrity. A

permanently-installed pool is constructed in or on the ground or in

a building such that it cannot be readily disassembled for storage.

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance in

a safe way and understand the hazards involved. Children shall not

play with the appliance. Cleaning and user maintenance shall not

be made by children without supervision.

• Cleaning and user maintenance must be performed by an adult

above 18 years old who is familiar with the risk of electric shock.

NOTES:

• Place the sand filter on solid, level ground. Ensure the sand filter is

at least 3.5 meters away from poolside. Keep distance as far as possible.

• Pay attention to position pool and sand filter so adequate

ventilation, drainage, and access for maintenance is available.

Never place the filter in an area that may accumulate water, or on a

walking path with lots of foot traffic.

• It is necessary to have the plug accessible after

installation of the pool. The plug of the sand

filter shall be at least 3.5m away from the pool.

• Atmospheric conditions may affect the

performance and life span of the sand filter;

take adequate precautions to protect the sand

filter from unnecessary wear and tear that may

occur during periods of cold or hot weather

and/or exposure to sun.

• Please examine and verify all sand filter components are present

before use. Notify Bestway at the customer service address listed on

this manual for any damaged or missing parts at the time of purchase.

• It is imperative to change as soon as possible all deteriorated

parts. Only use parts approved by the manufacturer.

• Do not allow children or adults to lean or sit on the apparatus.

• Do not add chemicals to the sand filter.

• When chemical products are used to clean the pool water, it is

recommended to respect a minimum filtration time to preserve the

health of swimmers which depends on compliance of health regulation.

• Only the media provided or specified by the manufacturer is to be

used with product installation.

• It is essential to check that the suction openings are not obstructed.

• It is advisable to stop the filtration during maintenance operations

on the filtration system.

• Regularly monitor the filter clogging level.

• A weekly check is recommended for backwashing or cleaning.

Minimum daily filtration operating time of 8 hours is recommended

to ensure clear pool water.

• It is essential to change any damaged element or set of elements

as soon as possible. Use only parts approved by person

responsible for placing the product on the market.

• All filters and filter media shall be inspected regularly to ensure that

there is not a build-up of detritus thus preventing good filtration.

Meaning of crossed-out wheeled dustbin:

Waste electrical products should not be disposed of with

household waste. Please recycle where facilities exist. Check with

your local authority or retailer for recycling advice.

The disposal of any used filter media should also be in accordance

with applicable regulations/legislation.

• Mind all the safety requirements and recommendations described

in the manual. In case of doubt on the pump or any circulation

devices, contact a qualified installer, or the

manufacturer/importer/distributor. The water circulation installation

shall comply with the European as well as national/local

regulations, especially when dealing with electrical issues. Any

change of valve position, pump size, grille size can cause a change

of the flow and the suction velocity can be increased.

• This product is not intended for commercial use.

PLEASE READ THE INSTRUCTION MANUAL CAREFULLY AND

KEEP IT FOR FUTURE REFERENCE.

SAVE THESE INSTRUCTIONS

RCD WARNING

WARNING: Before inserting plug into a power outlet, make

sure the current rate of the power outlet is suitable for the sand

filter.

WARNING: Risk of electric shock. The RCD plug must be

tested before each use.

WARNING: Insert the RCD plug into a residual current device

(RCD) having a rated residual operating not exceeding 30 mA.

WARNING: Do not use the sand filter if this test fails. For

assistance, please visit the support section on our website,

www.bestwaycorp.com.

PUMP DISPOSAL

Before assembling the sand filter, take a few minutes to

become familiar with all the sand filter parts.

Filter Diameter:

Effective Filter Area:

Max. Operating Pressure:

Working sand filter pressure:

Max. Water Temperature:

Sand:

Sand Size:

Sand Capacity:

480 mm

0.181 m2 (1.95 ft2 )

1.59 Bar (23 PSI)

<0.55 Bar (8 PSI)

35°C

Not included

#20 silica sand,0.45-0.85 mm

Approximately 55 kg

480 mm

690 mm

745 mm

SPECIFICATIONS

PARTS REFERENCE OVERVIEW

P03831

P61138ASS16

P03832

P61209ASS16

P03819

P03820

P61211ASS16

P6581ASS16

P6580ASS16

P03818

P6614ASS16

P6029ASS16

P03830

P61214ASS16

P61210ASS16

P03829

P6916ASS16

P6124ASS16

P6561ASS16

P6562ASS16

P6563ASS16

P03815

P03849

P6028FRASS16

P61322ASS16

P61318ASS16

P6643ASS16

REF.NO

SPARE PART NO.

P61322ASS16 P61318ASS16

(You will need a screwdriver.)

1.Carefully remove all components from the package and check

to ensure nothing is damaged. If equipment

is damaged, immediately notify the retailer

from where the equipment was purchased.

2.The sand filter should be placed on solid, level

ground, preferably a concrete slab. Position

the sand filter so the Ports and Control Valve are acces sible for

operation, servicing and winterizing.

3.EN60335-2-41 TEST standard requires the sand filter must

be vertically fixed on ground or a certain pedestal made of

wood or concrete before use to prevent the sand filter from

accidental falling. Fully assembled sand filter will exceed

18 kg. The mounting holes should be 8 mm in diameter and

spaced 86 mm apart. Use two bolts and nuts with a maximum

of 8 mm in diameter to fasten the sand filter to the pedestal.

LOAD POOL-GRADE FILTER SAND/FLOWCLEAR™

POLYSPHERE.

NOTE: Use only special pool-grade filter sand, free of all

limestone or clay: #20 Silica sand 0.45-0.85 mm,

approximately one 55 kg bag should suffice. If you do not use

the recommended size of filter sand, filtering performance will

be reduced and the sand filter may damaged, thereby voiding

the warranty.

NOTE: To avoid damaging the Skimmer when adding sand,

pour some water into the Bottom Tank to submerse the

Skimmer on the Hub.

NOTE: Sand/Flowclear™ Polysphere not included.

NOTE: Use 28 g (0.06 lbs) Flowclear™ Polysphere to replace

1 kg (2.20 lbs) sand.

Ф8 mm

86 mm

ASSEMBLY

MAX.

MIN .

#20

0.45-0.85 mm

MAX

MIN

FOR POOL WITH 32 MM VALVES

Before switching on, please read the manual carefully.

STOP

CONNECT TO THE POOL

Garden hose (not included)

For Drain, Backwash,

Rinse function

P61318ASS16 P61322ASS16

P6916ASS16

TIMER

1.Plug into power source, adjust power switch to “ON” (-)

position. The sand filter will begin working immediately.

2.Adjust power switch to “OFF” (0) position. The sand filter

will stop working immediately.

3.After turning on, you can adjust work time, rest time and

cycle time by turning the knob to desired position. See the

table below for more details.

4.When the timer knob is moved into new position, the filter’s

previous cycle

automatically cancels so

new cycle can begin.

5.Each time the filter is

powered on or restarted,

a new cycle will begin

based on timer knob

position.

NOTE: If the knob is

adjusted to the 24-hour

position (24), the sand filter will work continuously without any

rest period.

1 2 3 4

RCD TEST

OPERATION

Knob Position Working time(H) Rest time(H) Cycle period(H)

CONTROL VALVE OVERVIEW

WARNING: To prevent equipment

damage and possible injury, always

switch off sand filter before

changing the Control Valve function.

Changing valve positions while the

pump is running can damage the

Control Valve, which may cause

personal injury or property damage.

How to Use the Control Valve:

Press down on the Control Valve handle and rotate to desired

function.

NOTE:

• Be sure all provisions for wastewater disposal meet

applicable local, state or national codes. Do not discharge

water where it will cause flooding or damage.

Backwash: This function is used to clean the

sand bed; water is pumped down through the

Collector Hub, upwards through the sand bed,

and deposited out of Port D.

Rinse: This function for initial startup, cleaning,

and sand bed leveling after Backwash; water is

pumped downwards through the sand bed, up

through the Collector Hub and deposited out of

the valve Port D.

Circulate: This function circulates pool water

bypassing the sand filter; use this function if the

filter is broken to collect debris in the Debris

Screens.

Drain: This function drains water from the pool;

another filter bypass setting, water is pumped

and deposited out of Port D, instead of returning

it to the pool.

Closed: This function stops water flowing

between the sand filter and the pool.

Filter: This function is used to filter pool water

and should be positioned here 99% of the time.

Water is pumped through the sand filter, where it

is cleaned and returned to the pool.

• When the Control Valve is set to the Backwash, Rinse, or

Drain position, water will discharge from Port D on the

Control Valve.

• Do not switch on or operate the sand filter with the Control

Valve set to the Closed function or it will seriously damage

the sand filter.

• Do not set the Control Valve between two functions, or it will

lead to leaking.

• To avoid water leakage, screw the Port D Cap onto the

Control Valve Port D before operating the filter or circulate

function.

AIR RELEASE

Press down the control valve handle and wait untill the water flow

from Port D to release the air.

NOTE: It is important to repeat this operation

every time you start the pump after

winterizing, maintenance and backwashing

the sand bed.

FIRST TIME USE INSTRUCTIONS

Backwash and Rinsing must be performed to prepare the pump for its

first use and to wash the sand.

CAUTION: DO NOT DRY RUN THE SAND FILTER

1. Press down on the Control Valve handle and rotate to the Backwash

function.

2. Plug in and run the sand filter for 3-5 minutes, or until the water runs

clear.

3. Switch off the sand filter and set the Control Valve to the Rinse function.

4. Switch on the sand filter and run the sand filter for 1 min. This circulates

water backwards through the sand filter and drains water out Port D.

5. Switch off the sand filter. Set the Control Valve to the Closed function.

6. Top up pool water if required.

IMPORTANT: This procedure removes water from the pool, which you’ll

need to replace.

Switch off the sand filter immediately if water levels near the pool’s Inlet

and Outlet valves.

Backwash Rinsing

NOTE:

• Be sure all provisions for wastewater disposal meet

applicable local, state or national codes. Do not discharge

water where it will cause flooding or damage.

• When the Control Valve is set to the Backwash, Rinse, or

Drain position, water will discharge from Port D on the

Control Valve.

• Do not switch on or operate the sand filter with the Control

Valve set to the Closed function or it will seriously damage

the sand filter.

• Do not set the Control Valve between two functions, or it will

lead to leaking.

• To avoid water leakage, screw the Port D Cap onto the

Control Valve Port D before operating the filter or circulate

function.

1. Now the sand filter is ready for use. Set the Control Valve

to the Filter function.

NOTE: To prevent the risk of electrical shock dry any excess

water from yourself and the sand filter.

IMPORTANT: Before operation, make sure the tank is placed

steadily on its base and connected correctly to the pump.

2. Switch on the sand filter to run it.

NOTE: The sand filter has now started its

filtering cycle. Check that water is returning

to the pool and take note of the filter

pressure on Pressure Gauge. Generally,

the recommended sand filter pressure is

less than 0.56 Bar (8.0 PSI) when it is

running.

CAUTION: You must ensure the sand

filter is switched off and unplugged

before any maintenance begins or

severe risk of injury or death exists. As

dirt builds up in the sand filter, the

pressure reading on Pressure Gauge will

increase. When the Pressure Gauge is

0.62 Bar (9.0 PSI) or higher, or water flow to the pool is too

low, it is time to clean the sand. To clean the sand bed, follow

all instructions outlined previously in: Backwash and

Rinsing.

NOTE:

The Pressure Gauge is just used for measuring the water

pressure, not used for precision measurement.

2. We recommend you clean the sand bed once a month or

less regularly depending on how often the pool is used. Do

not clean the sand too frequently.

1.6

10 15

1.4

1.2

0.8

0.6

0.4

0.2

psi

bar

SAND FILTER MAINTENANCE

1. Switch off the sand filter and set the Control Valve to the

Closed function.

2. Close the connection valves.

3. Remove the Strainer Cover by

unscrewing it.

4. Take out the Strainer, remove any debris.

5. Put the Strainer back into position.

Ensure the hole in the strainer is aligned.

6. Ensure the Seal Ring is in place. Secure

the Strainer Cover back.

7. Open the connection valves.

NOTE: The Strainer must be emptied and

cleaned periodically. A dirty or blocked

strainer will reduce the performance of the

sand filter.

1. Switch off the sand filter and set Control Valve to the Drain

function.

2. Detach the Hose from the pool’s Port A and sand filter Port

A and attach to Port D.

3. Switch on the sand filter and press the “RESET” button to

run the filter and remove the pool water.

WARNING: DO NOT DRY RUN THE SAND FILTER.

CLEANING THE STRAINER

LOWERING OR DRAINING POOL WATER

In areas that have freezing winter temperatures, pool

equipment must be winterized to protect against damage.

Allowing water to freeze will damage the sand filter and void

warranty.

1. Backwash the sand filter.

2. Drain the pool according to the pool owner’s manual.

3. Unscrew the drain valve cap at the bottom of the tank and

STORAGE

release the remaining water.

4. Disconnect the two Hoses from the pool and the sand filter.

5. Completely spill the sand out of the tank and dry all

components.

6. Move away sand filter from pool area, store the sand filter

in a dry indoor location out of child’s reach.

Problems Probable Causes Solutions

Sand is flowing

to the pool

No water flow

Excessive filter

pressure

Control Valve leaks

from the port D

Connectors leak

- Sand is too small

- Move the control valve from the

backwash to the filter function without

stop the sand filter

- The level of the sand is too high

- The skimmer is broken

- Stopper plugs were not removed

- Air was not released

- The control valve is set to Closed

- The strainer is blocked

- Sand filter broken

- Dirty filter

- Calcified sand bed

- Insufficient backwashing

- The pressure gauge is broken

- Control Valve is set between two

functions

- The gasket is broken

Washer of the connectors not in place

- Washer of the connectors broken

- Loose Hoses

- Recommend 0.45 mm to 0.85 mm #20

silica sand

- Stop the sand filter every time set the

control valve

- Check if the level of the sand is between

the marked “MAX” and “ MIN” on the

collector hub

- Replace the skimmer

- Remove the stopper plugs and insert the

debris screens

- Release the air

- Set to filter function

- Clean the strainer

- Call for service

- Backwash

- Inspect sand and change if necessary

- Backwash until water runs clear

- Replace the pressure gauge

- Set to one function

- Replace the gasket

- Reposition the washer

- Replace the washer

- Tighten them

In areas that have freezing winter temperatures, pool

equipment must be winterized to protect against damage.

Allowing water to freeze will damage the sand filter and void

warranty.

1. Backwash the sand filter.

2. Drain the pool according to the pool owner’s manual.

3. Unscrew the drain valve cap at the bottom of the tank and

release the remaining water.

4. Disconnect the two Hoses from the pool and the sand filter.

5. Completely spill the sand out of the tank and dry all

components.

6. Move away sand filter from pool area, store the sand filter

in a dry indoor location out of child’s reach.

TROUBLESHOOTING

ACHTUNG

WICHTIGE SICHERHEITSANWEISUNGEN BITTE LESEN UND BEACHTEN

SIE ALLE SICHERHEITSBESTIMMUNGEN.

Bei der Installation und der Benutzung von elektrischen Geräten müssen die

grundlegenden Sicherheitsbestimmungen einschließlich der folgenden immer

beachtet werden:

• Die Pumpe muss über einen Trenntransformator oder über eine

Fehlerstrom-Schutzeinrichtung (RCD) mit einem Ansprechdifferenzstrom von

nicht mehr als 30mA versorgt werden.

• Die Stromquelle muss mindestens 4 m vom Pool entfernt sein.

• Das Gerät muss von einer geerdete Stromquelle mit Spannung versorgt werden

• ELEKTROSCHOCKGEFAHR - Die Pumpe darf nicht betrieben werden, wenn

sich Personen im Pool aufhalten. Bei defektem Sandfilter darf der Pool nicht

genutzt werden.

• VERGRABEN SIE KEINE KABEL. Verlegen Sie die Kabel so, dass die Gefahr

einer Beschädigung durch Rasenmäher, Heckenscheren usw. vermieden wird.

• Ersetzen Sie beschädigte Kabel sofort, um jede Gefahr von elektrischen

Schlägen zu vermeiden.

• Falls das Netzkabel beschädigt ist, muss es durch den Hersteller, den

Kundendienst oder in entsprechender Weise qualifizierte Person ausgewechselt

werden, um die Gefahr von Stromschlägen zu vermeiden.

• Es können keine Verlängerungskabel verwendet werden.

• Elektroschlaggefahr. Der Einsatz des Sandfilters mit einer ungeeigneten

Stromversorgung ist gefährlich und kann zu schweren Funktionsstörungen des

Sandfilters führen.

• Entfernen Sie den Erdungsleiter nicht und nehmen Sie keine Änderungen am

Stecker vor. Verwenden Sie keine Adapterstecker. Lassen Sie die Erdung Ihrer

Steckdosen von einem qualifizierten Elektriker überprüfen.

• Behandeln Sie den Sandfilter vorsichtig. Ziehen oder tragen Sie den Sandfilter nicht

am Netzkabel. Ziehen Sie den Stecker nie mit dem Netzkabel aus der Steckdose.

Schützen Sie das Kabel vor Beschädigungen. Der Sandfilter muss vor

scharfkantigen Gegenständen, Öl, beweglichen Teilen und Hitze geschützt werden.

• Trennen Sie dieses Produkt immer von der Stromversorgung, bevor Sie es

ausbauen, reinigen, warten oder Einstellungen daran vornehmen.

• Stecken Sie das Gerät nicht mit nassen Händen ein oder aus.

• Stecken Sie das Gerät immer aus:

• An Regentagen

• Bevor Reinigungs- oder Wartungsarbeiten durchgeführt werden.

• wenn Sie das Produkt für einen längeren Zeitraum unbeaufsichtigt lassen

(z. B. während des Urlaubs)

• Wird das Gerät für einen längeren Zeitraum nicht benutzt (z. B. im Winter),

muss das Poolset demontiert und in Innenräumen gelagert werden.

• Vorsicht: Bitte lesen Sie diese Anweisungen jedes Mal sorgfältig durch, bevor

Sie das Gerät benutzen und installieren/montieren.

• Bewahren Sie diese Anweisungen sorgfältig auf. Beachten Sie bei jedem

erneuten Aufbau des Pools diese Anweisungen.

• Sollten diese Anweisungen verloren gehen, kontaktieren Sie Bestway oder

suchen Sie das Dokument auf unserer Website: www.bestwaycorp.com

• Elektrische Installationen sollten die nationalen Anschlussvorschriften beachten.

Lassen Sie sich von einem qualifizierten Elektriker in allen Fragen beraten.

ACHTUNG: Dieser Sandfilter wurde ausschließlich für die Benutzung in

lagerbaren Pools konzipiert. Nicht in fest installierten Pools benutzen. Ein

lagerbarer Pool ist so konstruiert, dass es zur Lagerung abgebaut und

anschließend wieder aufgebaut werden kann. Ein fest installierter Pool ist so

konstruiert, dass es nicht für die Lagerung abgebaut werden kann.

• Dieses Gerät kann von Kindern ab 8 Jahren oder älter sowie von Personen mit

physischen, sensorischen oder mentalen Einschränkungen oder mangelnder

Erfahrung und mangelnden Kenntnissen benutzt werden, sofern sie

entsprechend beaufsichtigt oder mit der Bedienung des Gerätes und den damit

verbundenen Gefahren vertraut gemacht wurden. Kinder dürfen nicht mit dem

Gerät spielen. Die Reinigung und Wartung durch den Benutzer darf von Kindern

nicht ohne Beaufsichtigung durchgeführt werden.

• Reinigung und Wartung durch den Benutzer müssen von einem mindestens 18

Jahre alten Erwachsenen durchgeführt werden, der mit den Gefahren eines

elektrischen Schlages vertraut ist.

HINWEIS:

• Setzen Sie den Sandfilter auf eine feste und ebene Unterlage. Bitte stellen Sie

sicher, dass sich der Sandfilter zumindest 3.5m vom

Rand des Pools entfernt befindet. Halten Sie so viel

Abstand wie möglich.

• Achten Sie darauf, dass die Position des Pools und des

Sandfilters eine angemessene Lüftung, die Dränage

und den Zugang für die Wartung gewährleistet.

Positionieren Sie den Sandfilter nie an einer Stelle, an

der sich Wasser ansammeln kann oder wo er den

Verkehr stört.

• Die Steckdose muss nach der Installation des Pools zugänglich sein. Die

Steckdose des Sandfilters sollte zumindest 3,5m vom Pool entfernt sein.

• Die Witterungsbedingungen können sich auf die Leistung und die Lebensdauer

des Sandfilters auswirken; schützen Sie den Sandfilter in geeigneter Weise vor

unnötigem Verschleiß bei kalter oder heißer Witterung und/oder

Sonnenaussetzung.

• Bitte prüfen Sie alle Komponenten des Sandfilters vor der Benutzung. Bitte

wenden Sie sich an den Bestway-Kundendienst unter der im Handbuch

angegebene Adresse, falls beim Kauf Teile fehlen oder beschädigt sind.

• Defekte Teile müssen unverzüglich ausgetauscht werden. Verwenden Sie

ausschließlich vom Hersteller empfohlene und zugelassene Teile.

• Stellen Sie sicher, dass sich niemand gegen das Gerät lehnt oder darauf setzt.

• Füllen Sie keine Chemikalien in den Sandfilter ein.

• Wenn Chemikalien zum Reinigen des Poolwassers eingesetzt werden,

empfehlen wir aus gesundheitlichen Gründen und zur Einhaltung von

Vorschriften die Einhaltung einer minimalen Filtrierungszeit.

• Bei der Produktinstallation sind nur die vom Hersteller gelieferten oder

angegebenen Medien zu verwenden.

• Es ist unbedingt notwendig zu prüfen, dass die Ansaugöffnungen nicht blockiert

sind.

• Es ist empfehlenswert, die Filterung während der Wartungseingriffe auf dem

Filtersystem zu stoppen.

• Regelmäßig das Verstopfen des Filters überwachen.

• Es wird eine wöchentliche Kontrolle für Rückspülen oder Reinigung empfohlen.

Die tägliche Mindestfilterbetriebsdauer von acht Stunden wird empfohlen, um

sauberes Poolwasser zu garantieren.

• Es ist unbedingt notwendig, jegliche beschädigten Elemente oder

Elementgruppen so schnell wie möglich zu ersetzen. Verwenden Sie nur von

der Person, die das Produkt auf den Markt gebracht hat, empfohlen Teile.

• Alle Filter und Filtermedien müssen regelmäßig untersucht werden, um

sicherzustellen, dass keine Schmutzansammlungen vorliegen, die eine korrekte

Filterung verhindern. Die Entsorgung jeglicher gebrauchten Filtermeiden muss in

Einklang mit den geltenden Vorschriften/Gesetzen erfolgen.

• Beachten Sie alle im Handbuch beschriebenen Sicherheitsvorschriften und

Empfehlungen. Im Fall von Zweifeln hinsichtlich der Pumpe oder

Umwälzvorrichtungen wenden Sie sich bitten an einen Installationsfachmann

oder an den Hersteller/Importeur/Händler. Die Installation der Wasserzirkulation

muss im Einklang mit den europäischen sowie den nationalen/lokalen

Bestimmungen erfolgen, insbesondere wenn es sich um elektrische Fragen

handelt. Jegliche Änderungen der Ventilposition, Pumpen-oder Gittergröße

kann zu einer Änderung des Durchflusses und einer Erhöhung der

Ansauggeschwindigkeit führen.

• Dieses Produkt darf nicht für kommerzielle Zwecke benutzt werden.

BITTE LESEN SIE DAS HANDBUCH SORGFÄLTIG DURCH UND

BEWAHREN SIE ES ALS KÜNFTIGE REFERENZ AUF.

BEWAHREN SIE DIESE ANWEISUNGEN AUF

RCD WARNHINWEISE

WARNUNG: Vergewissern Sie sich, dass die Netzspannung der Steckdose für

die Pumpe geeignet ist, bevor Sie den Netzstecker in dieSteckdose einstecken.

WARNUNG: Gefahr eines elektrischen schlags. Der RCD-Anschluss muss vor

jeder Benutzung getestet werden.

WARNUNG: Schließen Sie den RCD-Stecker an eine

Fehlerstrom-Schutzeinrichtung an, deren Ansprechdifferenzstrom mehr 30mA

nicht übersteigt.

WARNUNG: Verwenden Sie die Pumpe nicht, wenn dieser Test scheitert. Wenn

Sie Hilfe benötigen, besuchen Sie bitte den Supportbereich auf unserer Website

www.bestwaycorp.com

Besuchen Sie den YouTube-Kanal

von Bestway

SICHERHEITSANWEISUNGEN

SANDFILTERANLAGE

GEBRAUCHSANLEITUNG

WIR EMPFEHLEN, DAS PRODUKT NICHT

BEIM VERKÄUFER ZURÜCKZUGEBEN

FRAGEN? PROBLEME?

FEHLENDE ERSATZTEILE?

Für FAQs, Handbücher, Aufbauvideos

und Ersatzteile gehen Sie auf

bestwaycorp.com/support