Bestway 58497 Le manuel du propriétaire

Marque: Bestway

Modèle: 58497

Taper: Le manuel du propriétaire

WE SUGGEST NOT TO RETURN

THE PRODUCT TO THE STORE

QUESTIONS? PROBLEMS?

MISSING PARTS?

For FAQ, Manuals, Videos Or

Spare Parts, Please Visit

bestwaycorp.com/support

58497 Hmax 1.5 m

OWNER’S MANUAL

bestwaycorp.com/support

Visit Bestway YouTube channel

SAND FILTER

OWNER’S MANUAL

Visit Bestway YouTube

channel

SAFETY INSTRUCTIONS

WARNING

IMPORTANT SAFETY INSTRUCTIONS -

READ AND FOLLOW ALL SAFETY INSTRUCTIONS -

SAVE THESE INSTRUCTIONS

When installing and using this electrical equipment, basic safety

precautions should always be followed, including the following:

• The pump is to be supplied by an isolating transformer or supplied

through a residual current device (RCD)having a rated residual

operating current not exceeding 30 mA.

• The power source on the wall of building should keep more than 4m

away from pool.

• The appliance must be supplied by earthed power source.

• RISK OF ELECTRIC SHOCK - The pump cannot be using while

people are inside the pool. Forbid the access of the pool in case of

damage of the sand filter.

• DO NOT BURY CORD. Locate cord to minimize abuse from lawn

mowers, hedge trimmers, and other equipment.

• To reduce the risk of electric shock, replace damaged cord immediately.

• If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similarly qualified persons in order to avoid a hazard.

• Extension cords can’t be used.

• Risk of electric shock. Using the sand filter with an unmatched electrical

supply is dangerous and will permanently damage the sand filter.

• Do not remove the grounding prong or modify the plug in anyway. Do

not use adaptor plugs. Consult a qualified electrician for any

questions relating to validity of your plugs or grounding.

• Handle the sand filter with care. Do not pull or carry the sand filter by

the power cord. Never pull a plug from the outlet by yanking the

power cord. Keep cord free from abrasions. Sharp objects, oil,

moving parts, and heat should never be exposed to the sand filter.

• Always unplug this product from the electrical outlet before removing,

cleaning, servicing or making any adjustment to the product.

• Don’t plug or unplug the appliance if hand is wet

• Always unplug the appliance:

• On raining days

• Before cleaning or other maintenance

• Leave it unattended on holidays

• When the appliance will be not used for long time, such as in the

winter, the pool set should be disassembled and stored indoor.

• CAUTION: Read the instruction before using the appliance and

installation/reassembly every time.

• Safekeeping the instruction. For reconstruction the pool set every

time, please always refer to the instructions.

• If instruction is missed, please contact with Bestway or search it in

website: www.bestwaycorp.com

• Electric installations should follow national wiring rules. Consult a

qualified electrician for any questions.

CAUTION: This sand filter is for use with storable pools only. Do not

use with permanently-installed pools. A storable pool is constructed so

that it is capable of being readily disassembled for storage and

reassembled to its original integrity. A permanently-installed pool is

constructed in or on the ground or in a building such that it cannot be

readily disassembled for storage.

• This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervi-

sion or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by

children without supervision.

• Cleaning and user maintenance must be performed by an adult

above18 years old who is familiar with the risk of electric shock.

NOTES:

• Place the sand filter on solid, level ground. Ensure the sand filter is at

least 3.5 meters away from poolside. Keep distance as far as possible.

• Pay attention to position pool and sand filter so adequate ventilation,

drainage, and access for maintenance is available. Never place the

sand filter in an area that may accumulate water, or on a walking path

with lots of foot traffic.

• It is necessary to have the plug accessible

after installation of the pool. The plug of

the sand filter shall be at least 3.5m away

from the pool.

• Atmospheric conditions may affect the

performance and life span of the sand

filter; take adequate precautions to protect

the sand filter from unnecessary wear and

tear that may occur during periods of cold

or hot weather and/or exposure to sun.

• Please examine and verify all sand filter components are present

before use. Notify Bestway at the customer service address listed on

this manual for any damaged or missing parts at the time of purchase.

• It is imperative to change as soon as possible all deteriorated parts.

Only use parts approved by the manufacturer.

• Do not allow children or adults to lean or sit on the apparatus.

• Do not add chemicals to the sand filter.

• When chemical products are used to clean the pool water, it is

recommended to respect a minimum filtration time to preserve the

health of swimmers which depends on compliance of health regulation.

• Only the media provided or specified by the manufacturer is to be

used with product installation.

• It is essential to check that the suction openings are not obstructed.

• It is advisable to stop the filtration during maintenance operations on

the filtration system.

• Regularly monitor the filter clogging level.

• A weekly check is recommended for backwashing or cleaning.

Minimum daily filtration operating time of 8 hours is recommended to

ensure clear pool water.

• It is essential to change any damaged element or set of elements as

soon as possible. Use only parts approved by person responsible for

placing the product on the market.

• All filters and filter media shall be inspected regularly to ensure that

there is not a build-up of detritus thus preventing good filtration. The

disposal of any used filter media should also be in accordance with

applicable regulations/legislation.

• Mind all the safety requirements and recommendations described in

the manual. In case of doubt on the pump or any circulation devices,

contact a qualified installer, or the manufacturer/importer/distributor.

The water circulation installation shall comply with the European as

well as national/local regulations, especially when dealing with electrical

issues. Any change of valve position, pump size, grille size can cause

a change of the flow and the suction velocity can be increased.

• This product is not intended for commercial use.

PLEASE READ THE INSTRUCTION MANUAL CAREFULLY

AND KEEP IT FOR FUTURE REFERENCE.

SAVE THESE INSTRUCTIONS

RCD WARNING

WARNING: Before inserting plug into a power outlet, make sure the

current rate of the power outlet is suitable for the sand filter.

WARNING: Risk of electric shock. The RCD plug must be tested before

each use.

WARNING: Insert the RCD plug into a residual current device (RCD)

having a rated residual operating not exceeding 30 mA.

WARNING: Do not use the sand filter if this test fails. For assistance,

please visit the support section on our website, www.bestwaycorp.com.

WE SUGGEST NOT TO RETURN

THE PRODUCT TO THE STORE

QUESTIONS? PROBLEMS?

MISSING PARTS?

For FAQ, Manuals, Videos Or

Spare Parts, Please Visit

bestwaycorp.com/support

WARNING

IMPORTANT SAFETY INSTRUCTIONS -

READ AND FOLLOW ALL SAFETY INSTRUCTIONS -

SAVE THESE INSTRUCTIONS

When installing and using this electrical equipment, basic safety

precautions should always be followed, including the following:

• The pump is to be supplied by an isolating transformer or supplied

through a residual current device (RCD)having a rated residual

operating current not exceeding 30 mA.

• The power source on the wall of building should keep more than 4m

away from pool.

• The appliance must be supplied by earthed power source.

• RISK OF ELECTRIC SHOCK - The pump cannot be using while

people are inside the pool. Forbid the access of the pool in case of

damage of the sand filter.

• DO NOT BURY CORD. Locate cord to minimize abuse from lawn

mowers, hedge trimmers, and other equipment.

• To reduce the risk of electric shock, replace damaged cord immediately.

• If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similarly qualified persons in order to avoid a hazard.

• Extension cords can’t be used.

• Risk of electric shock. Using the sand filter with an unmatched electrical

supply is dangerous and will permanently damage the sand filter.

• Do not remove the grounding prong or modify the plug in anyway. Do

not use adaptor plugs. Consult a qualified electrician for any

questions relating to validity of your plugs or grounding.

• Handle the sand filter with care. Do not pull or carry the sand filter by

the power cord. Never pull a plug from the outlet by yanking the

power cord. Keep cord free from abrasions. Sharp objects, oil,

moving parts, and heat should never be exposed to the sand filter.

• Always unplug this product from the electrical outlet before removing,

cleaning, servicing or making any adjustment to the product.

• Don’t plug or unplug the appliance if hand is wet

• Always unplug the appliance:

• On raining days

• Before cleaning or other maintenance

• Leave it unattended on holidays

• When the appliance will be not used for long time, such as in the

winter, the pool set should be disassembled and stored indoor.

• CAUTION: Read the instruction before using the appliance and

installation/reassembly every time.

• Safekeeping the instruction. For reconstruction the pool set every

time, please always refer to the instructions.

• If instruction is missed, please contact with Bestway or search it in

website: www.bestwaycorp.com

• Electric installations should follow national wiring rules. Consult a

qualified electrician for any questions.

CAUTION: This sand filter is for use with storable pools only. Do not

use with permanently-installed pools. A storable pool is constructed so

that it is capable of being readily disassembled for storage and

reassembled to its original integrity. A permanently-installed pool is

constructed in or on the ground or in a building such that it cannot be

readily disassembled for storage.

• This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervi-

sion or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by

children without supervision.

• Cleaning and user maintenance must be performed by an adult

above18 years old who is familiar with the risk of electric shock.

NOTES:

• Place the sand filter on solid, level ground. Ensure the sand filter is at

least 3.5 meters away from poolside. Keep distance as far as possible.

• Pay attention to position pool and sand filter so adequate ventilation,

drainage, and access for maintenance is available. Never place the

sand filter in an area that may accumulate water, or on a walking path

with lots of foot traffic.

• It is necessary to have the plug accessible

after installation of the pool. The plug of

the sand filter shall be at least 3.5m away

from the pool.

• Atmospheric conditions may affect the

performance and life span of the sand

filter; take adequate precautions to protect

the sand filter from unnecessary wear and

tear that may occur during periods of cold

or hot weather and/or exposure to sun.

• Please examine and verify all sand filter components are present

before use. Notify Bestway at the customer service address listed on

this manual for any damaged or missing parts at the time of purchase.

• It is imperative to change as soon as possible all deteriorated parts.

Only use parts approved by the manufacturer.

• Do not allow children or adults to lean or sit on the apparatus.

• Do not add chemicals to the sand filter.

• When chemical products are used to clean the pool water, it is

recommended to respect a minimum filtration time to preserve the

health of swimmers which depends on compliance of health regulation.

• Only the media provided or specified by the manufacturer is to be

used with product installation.

• It is essential to check that the suction openings are not obstructed.

• It is advisable to stop the filtration during maintenance operations on

the filtration system.

• Regularly monitor the filter clogging level.

• A weekly check is recommended for backwashing or cleaning.

Minimum daily filtration operating time of 8 hours is recommended to

ensure clear pool water.

• It is essential to change any damaged element or set of elements as

soon as possible. Use only parts approved by person responsible for

placing the product on the market.

• All filters and filter media shall be inspected regularly to ensure that

there is not a build-up of detritus thus preventing good filtration. The

disposal of any used filter media should also be in accordance with

applicable regulations/legislation.

• Mind all the safety requirements and recommendations described in

the manual. In case of doubt on the pump or any circulation devices,

contact a qualified installer, or the manufacturer/importer/distributor.

The water circulation installation shall comply with the European as

well as national/local regulations, especially when dealing with electrical

issues. Any change of valve position, pump size, grille size can cause

a change of the flow and the suction velocity can be increased.

• This product is not intended for commercial use.

PLEASE READ THE INSTRUCTION MANUAL CAREFULLY

AND KEEP IT FOR FUTURE REFERENCE.

SAVE THESE INSTRUCTIONS

RCD WARNING

WARNING: Before inserting plug into a power outlet, make sure the

current rate of the power outlet is suitable for the sand filter.

WARNING: Risk of electric shock. The RCD plug must be tested before

each use.

WARNING: Insert the RCD plug into a residual current device (RCD)

having a rated residual operating not exceeding 30 mA.

WARNING: Do not use the sand filter if this test fails. For assistance,

please visit the support section on our website, www.bestwaycorp.com.

WARNING

IMPORTANT SAFETY INSTRUCTIONS -

READ AND FOLLOW ALL SAFETY INSTRUCTIONS -

SAVE THESE INSTRUCTIONS

When installing and using this electrical equipment, basic safety

precautions should always be followed, including the following:

• The pump is to be supplied by an isolating transformer or supplied

through a residual current device (RCD)having a rated residual

operating current not exceeding 30 mA.

• The power source on the wall of building should keep more than 4m

away from pool.

• The appliance must be supplied by earthed power source.

• RISK OF ELECTRIC SHOCK - The pump cannot be using while

people are inside the pool. Forbid the access of the pool in case of

damage of the sand filter.

• DO NOT BURY CORD. Locate cord to minimize abuse from lawn

mowers, hedge trimmers, and other equipment.

• To reduce the risk of electric shock, replace damaged cord immediately.

• If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similarly qualified persons in order to avoid a hazard.

• Extension cords can’t be used.

• Risk of electric shock. Using the sand filter with an unmatched electrical

supply is dangerous and will permanently damage the sand filter.

• Do not remove the grounding prong or modify the plug in anyway. Do

not use adaptor plugs. Consult a qualified electrician for any

questions relating to validity of your plugs or grounding.

• Handle the sand filter with care. Do not pull or carry the sand filter by

the power cord. Never pull a plug from the outlet by yanking the

power cord. Keep cord free from abrasions. Sharp objects, oil,

moving parts, and heat should never be exposed to the sand filter.

• Always unplug this product from the electrical outlet before removing,

cleaning, servicing or making any adjustment to the product.

• Don’t plug or unplug the appliance if hand is wet

• Always unplug the appliance:

• On raining days

• Before cleaning or other maintenance

• Leave it unattended on holidays

• When the appliance will be not used for long time, such as in the

winter, the pool set should be disassembled and stored indoor.

• CAUTION: Read the instruction before using the appliance and

installation/reassembly every time.

• Safekeeping the instruction. For reconstruction the pool set every

time, please always refer to the instructions.

• If instruction is missed, please contact with Bestway or search it in

website: www.bestwaycorp.com

• Electric installations should follow national wiring rules. Consult a

qualified electrician for any questions.

CAUTION: This sand filter is for use with storable pools only. Do not

use with permanently-installed pools. A storable pool is constructed so

that it is capable of being readily disassembled for storage and

reassembled to its original integrity. A permanently-installed pool is

constructed in or on the ground or in a building such that it cannot be

readily disassembled for storage.

• This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervi-

sion or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by

children without supervision.

• Cleaning and user maintenance must be performed by an adult

above18 years old who is familiar with the risk of electric shock.

NOTES:

• Place the sand filter on solid, level ground. Ensure the sand filter is at

least 3.5 meters away from poolside. Keep distance as far as possible.

• Pay attention to position pool and sand filter so adequate ventilation,

drainage, and access for maintenance is available. Never place the

sand filter in an area that may accumulate water, or on a walking path

with lots of foot traffic.

• It is necessary to have the plug accessible

after installation of the pool. The plug of

the sand filter shall be at least 3.5m away

from the pool.

• Atmospheric conditions may affect the

performance and life span of the sand

filter; take adequate precautions to protect

the sand filter from unnecessary wear and

tear that may occur during periods of cold

or hot weather and/or exposure to sun.

• Please examine and verify all sand filter components are present

before use. Notify Bestway at the customer service address listed on

this manual for any damaged or missing parts at the time of purchase.

• It is imperative to change as soon as possible all deteriorated parts.

Only use parts approved by the manufacturer.

• Do not allow children or adults to lean or sit on the apparatus.

• Do not add chemicals to the sand filter.

• When chemical products are used to clean the pool water, it is

recommended to respect a minimum filtration time to preserve the

health of swimmers which depends on compliance of health regulation.

• Only the media provided or specified by the manufacturer is to be

used with product installation.

• It is essential to check that the suction openings are not obstructed.

• It is advisable to stop the filtration during maintenance operations on

the filtration system.

• Regularly monitor the filter clogging level.

• A weekly check is recommended for backwashing or cleaning.

Minimum daily filtration operating time of 8 hours is recommended to

ensure clear pool water.

• It is essential to change any damaged element or set of elements as

soon as possible. Use only parts approved by person responsible for

placing the product on the market.

• All filters and filter media shall be inspected regularly to ensure that

there is not a build-up of detritus thus preventing good filtration. The

disposal of any used filter media should also be in accordance with

applicable regulations/legislation.

• Mind all the safety requirements and recommendations described in

the manual. In case of doubt on the pump or any circulation devices,

contact a qualified installer, or the manufacturer/importer/distributor.

The water circulation installation shall comply with the European as

well as national/local regulations, especially when dealing with electrical

issues. Any change of valve position, pump size, grille size can cause

a change of the flow and the suction velocity can be increased.

• This product is not intended for commercial use.

PLEASE READ THE INSTRUCTION MANUAL CAREFULLY

AND KEEP IT FOR FUTURE REFERENCE.

SAVE THESE INSTRUCTIONS

RCD WARNING

WARNING: Before inserting plug into a power outlet, make sure the

current rate of the power outlet is suitable for the sand filter.

WARNING: Risk of electric shock. The RCD plug must be tested before

each use.

WARNING: Insert the RCD plug into a residual current device (RCD)

having a rated residual operating not exceeding 30 mA.

WARNING: Do not use the sand filter if this test fails. For assistance,

please visit the support section on our website, www.bestwaycorp.com.

>3.5 m

POOL

Filter Diameter:

Effective Fiter Area:

Max. Operating Pressure:

Working sand filter pressure:

Max. Water Temperature:

Sand:

Sand Size:

Sand Capacity:

385 mm

0.11 m2(1.18 ft2)

0.83 Bar(12 PSI)

<0.45 Bar(6.5 PSI)

35°C

Not included

#20 silica sand,0.45-0.85 mm

Approximately 36 kg

385 mm

640 mm

650 mm

WARNING

IMPORTANT SAFETY INSTRUCTIONS -

READ AND FOLLOW ALL SAFETY INSTRUCTIONS -

SAVE THESE INSTRUCTIONS

When installing and using this electrical equipment, basic safety

precautions should always be followed, including the following:

• The pump is to be supplied by an isolating transformer or supplied

through a residual current device (RCD)having a rated residual

operating current not exceeding 30 mA.

• The power source on the wall of building should keep more than 4m

away from pool.

• The appliance must be supplied by earthed power source.

• RISK OF ELECTRIC SHOCK - The pump cannot be using while

people are inside the pool. Forbid the access of the pool in case of

damage of the sand filter.

• DO NOT BURY CORD. Locate cord to minimize abuse from lawn

mowers, hedge trimmers, and other equipment.

• To reduce the risk of electric shock, replace damaged cord immediately.

• If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similarly qualified persons in order to avoid a hazard.

• Extension cords can’t be used.

• Risk of electric shock. Using the sand filter with an unmatched electrical

supply is dangerous and will permanently damage the sand filter.

• Do not remove the grounding prong or modify the plug in anyway. Do

not use adaptor plugs. Consult a qualified electrician for any

questions relating to validity of your plugs or grounding.

• Handle the sand filter with care. Do not pull or carry the sand filter by

the power cord. Never pull a plug from the outlet by yanking the

power cord. Keep cord free from abrasions. Sharp objects, oil,

moving parts, and heat should never be exposed to the sand filter.

• Always unplug this product from the electrical outlet before removing,

cleaning, servicing or making any adjustment to the product.

• Don’t plug or unplug the appliance if hand is wet

• Always unplug the appliance:

• On raining days

• Before cleaning or other maintenance

• Leave it unattended on holidays

• When the appliance will be not used for long time, such as in the

winter, the pool set should be disassembled and stored indoor.

• CAUTION: Read the instruction before using the appliance and

installation/reassembly every time.

• Safekeeping the instruction. For reconstruction the pool set every

time, please always refer to the instructions.

• If instruction is missed, please contact with Bestway or search it in

website: www.bestwaycorp.com

• Electric installations should follow national wiring rules. Consult a

qualified electrician for any questions.

CAUTION: This sand filter is for use with storable pools only. Do not

use with permanently-installed pools. A storable pool is constructed so

that it is capable of being readily disassembled for storage and

reassembled to its original integrity. A permanently-installed pool is

constructed in or on the ground or in a building such that it cannot be

readily disassembled for storage.

• This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervi-

sion or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by

children without supervision.

• Cleaning and user maintenance must be performed by an adult

above18 years old who is familiar with the risk of electric shock.

NOTES:

• Place the sand filter on solid, level ground. Ensure the sand filter is at

least 3.5 meters away from poolside. Keep distance as far as possible.

• Pay attention to position pool and sand filter so adequate ventilation,

drainage, and access for maintenance is available. Never place the

sand filter in an area that may accumulate water, or on a walking path

with lots of foot traffic.

• It is necessary to have the plug accessible

after installation of the pool. The plug of

the sand filter shall be at least 3.5m away

from the pool.

• Atmospheric conditions may affect the

performance and life span of the sand

filter; take adequate precautions to protect

the sand filter from unnecessary wear and

tear that may occur during periods of cold

or hot weather and/or exposure to sun.

• Please examine and verify all sand filter components are present

before use. Notify Bestway at the customer service address listed on

this manual for any damaged or missing parts at the time of purchase.

• It is imperative to change as soon as possible all deteriorated parts.

Only use parts approved by the manufacturer.

• Do not allow children or adults to lean or sit on the apparatus.

• Do not add chemicals to the sand filter.

• When chemical products are used to clean the pool water, it is

recommended to respect a minimum filtration time to preserve the

health of swimmers which depends on compliance of health regulation.

• Only the media provided or specified by the manufacturer is to be

used with product installation.

• It is essential to check that the suction openings are not obstructed.

• It is advisable to stop the filtration during maintenance operations on

the filtration system.

• Regularly monitor the filter clogging level.

• A weekly check is recommended for backwashing or cleaning.

Minimum daily filtration operating time of 8 hours is recommended to

ensure clear pool water.

• It is essential to change any damaged element or set of elements as

soon as possible. Use only parts approved by person responsible for

placing the product on the market.

• All filters and filter media shall be inspected regularly to ensure that

there is not a build-up of detritus thus preventing good filtration. The

disposal of any used filter media should also be in accordance with

applicable regulations/legislation.

• Mind all the safety requirements and recommendations described in

the manual. In case of doubt on the pump or any circulation devices,

contact a qualified installer, or the manufacturer/importer/distributor.

The water circulation installation shall comply with the European as

well as national/local regulations, especially when dealing with electrical

issues. Any change of valve position, pump size, grille size can cause

a change of the flow and the suction velocity can be increased.

• This product is not intended for commercial use.

PLEASE READ THE INSTRUCTION MANUAL CAREFULLY

AND KEEP IT FOR FUTURE REFERENCE.

SAVE THESE INSTRUCTIONS

RCD WARNING

WARNING: Before inserting plug into a power outlet, make sure the

current rate of the power outlet is suitable for the sand filter.

WARNING: Risk of electric shock. The RCD plug must be tested before

each use.

WARNING: Insert the RCD plug into a residual current device (RCD)

having a rated residual operating not exceeding 30 mA.

WARNING: Do not use the sand filter if this test fails. For assistance,

please visit the support section on our website, www.bestwaycorp.com.

Meaning of crossed-out wheeled dustbin:

Waste electrical products should not be disposed of with

household waste. Please recycle where facilities exist.

Check with your local authority or retailer for recyclingadvice.

SPECIFICATIONS

PUMP DISPOSAL

Before assembling the sand filter, take a few minutes to become

familiar with all the sand filter parts.

REF.NO

SPARE PART NO.

P03831

P61138ASS16

P03832

P61209ASS16

P03843

P03844

P61211ASS16

P6581ASS16

P6580ASS16

P03845

P6614ASS16

P6029ASS16

P03830

P61214ASS16

P61210ASS16

P03829

P6916ASS16

P6124ASS16

P6561ASS16

P6562ASS16

P6563ASS16

P00561

P03840

P6028FRASS16

P61322ASS16

P61318ASS16

P6643ASS16

(You will need a screwdriver.)

1. Carefully remove all components

from the package and check to

ensure nothing is damaged. If

equipment is damaged, immediately

notify the retailer from where the

equipment was purchased.

2. The sand filter should be placed on

solid, level ground, preferably a

concrete slab. Position the sand filter

P61322ASS16 P61318ASS16

Ф8 mm

86 mm

PARTS REFERENCE OVERVIEW

ASSEMBLY

so the Ports and Control Valve are accessible for

operation, servicing and winterizing.

3. EN60335-2-41 TEST standard requires the sand filter to

be vertically fixed on ground or a certain pedestal made

of wood or concrete before use to prevent the sand filter

from accidentally falling. Fully assembled sand filter will

exceed 18 kg. The mounting holes should be 8 mm in

diameter and spaced 86 mm apart. Use two bolts and

nuts with a maximum of 8 mm in diameter to fasten the

sand filter to the pedestal.

CX2 X1 X1

BX2

LOAD POOL-GRADE FILTER SAND/FLOWCLEAR™ POLYSPHERE.

NOTE: Use only special pool-grade filter sand, free of all limestone

or clay: #20 Silica sand 0.45-0.85 mm, approximately one 36 kg bag

should suffice. If you do not use the recommended size filter sand,

filtering performance will be reduced and the sand filter may

damaged, thereby voiding warranty.

IMPORTANT: We suggest using #20 silica sand with your pool sand

filter. It is specially graded to trap particles in the 20 - 100 micron

range.

Some small debris can pass throw the sand and back into the pool.

This is normal, especially if the debris is fine or silt.

To limit this, it is better to follow the maintenance instructions, and

backwash and rinse when necessary.

We also suggest contacting your pool dealer for the chemical

product specifically made to clean the sand. The correct

maintenance of the sand will optimize the cleaning efficiency and

avoid accumulation of oils or scale.

When you are vacuuming the bottom of the pool that has a large

amount of debris, we suggest to backwash the sand when you finish

cleaning half of the pool.

Remember to backwash and rinse the sand after vacuuming the

bottom of the pool each time.

NOTE: To avoid damaging the Skimmer when adding sand, pour

some water into the Bottom Tank to submerse the Skimmer on the

Collector Hub.

NOTE: Sand/Flowclear™ Polysphere not included.

NOTE: Use 28 g (0.06 lbs) Flowclear™ Polysphere to replace

1 kg (2.20 lbs) sand.

(You will need a screwdriver.)

1. Carefully remove all components

from the package and check to

ensure nothing is damaged. If

equipment is damaged, immediately

notify the retailer from where the

equipment was purchased.

2. The sand filter should be placed on

solid, level ground, preferably a

concrete slab. Position the sand filter

so the Ports and Control Valve are accessible for

operation, servicing and winterizing.

3. EN60335-2-41 TEST standard requires the sand filter to

be vertically fixed on ground or a certain pedestal made

of wood or concrete before use to prevent the sand filter

from accidentally falling. Fully assembled sand filter will

exceed 18 kg. The mounting holes should be 8 mm in

diameter and spaced 86 mm apart. Use two bolts and

nuts with a maximum of 8 mm in diameter to fasten the

sand filter to the pedestal.

MAX.

MIN .

#20

0.45-0.85 mm

MAX

MIN

CONNECT TO THE POOL

TIMER

1.Plug into power source, adjust power switch to “ON” (-) position.

The sand filter will begin working immediately.

2.Adjust power switch to “OFF” (0) position. The sand filter will

FOR POOL WITH 32 MM (1.25 IN.) VALVE

STOP Before switching on, please read the manual carefully.

Garden hose (not included)

For Drain, Backwash,

Rinse function

1 2 3 4

RCD TEST

OPERATION

stop working

immediately.

3.After turning on, you

can adjust work time,

rest time and cycle

time by turning the

knob to desired

position. See the table

below for more details.

When the timer knob is

moved into new

position, the filter’s previous cycle automatically cancels so new

cycle can begin.

5.Each time the filter is powered on or restarted, a new cycle will

begin based on timer knob position.

NOTE: If the knob is adjusted to the 24-hour position (24), the

sand filter will work continuously without any rest period.

P61318ASS16 P61322ASS16

P6916ASS16

TIMER

1.Plug into power source, adjust power switch to “ON” (-) position.

The sand filter will begin working immediately.

2.Adjust power switch to “OFF” (0) position. The sand filter will

Knob Position Working time(H) Rest time(H) Cycle period(H)

4 4 20 24

6 6 18 24

8 8 16 24

10 10 14 24

12 12 12 24

24 24 0 24

P4 4 4 8

P6 6 6 12

P8 8 8 16

stop working

immediately.

3.After turning on, you

can adjust work time,

rest time and cycle

time by turning the

knob to desired

position. See the table

below for more details.

When the timer knob is

moved into new

position, the filter’s previous cycle automatically cancels so new

cycle can begin.

5.Each time the filter is powered on or restarted, a new cycle will

begin based on timer knob position.

NOTE: If the knob is adjusted to the 24-hour position (24), the

sand filter will work continuously without any rest period.

CONTROL VALVE OVERVIEW

WARNING: To prevent

equipment damage and

possible injury, always switch

off sand filter before changing

the Control Valve function.

Changing valve positions while

the pump is running can

damage the Control Valve, which may cause personal injury

or property damage.

How to Use the Control Valve:

Press down on the Control Valve handle and rotate to desired

function.

CONTROL VALVE FUNCTIONS

The Control valve is used to select 6 different filter functions:

Filter, Closed, Backwash, Rinse, Drain and Circulate.

CONTROL VALVE OVERVIEW

WARNING: To prevent

equipment damage and

possible injury, always switch

off sand filter before changing

the Control Valve function.

Changing valve positions while

the pump is running can

damage the Control Valve, which may cause personal injury

or property damage.

How to Use the Control Valve:

Press down on the Control Valve handle and rotate to desired

function.

CONTROL VALVE FUNCTIONS

The Control valve is used to select 6 different filter functions:

Filter, Closed, Backwash, Rinse, Drain and Circulate.

Filter: This function is used to filter pool water

and should be positioned here 99% of the time.

Water is pumped through the sand filter, where

it is cleaned and returned to the pool.

Closed: This function stops water

flowing between the sand filter and the

pool.

Backwash: This function is used to

clean the sand bed; water is pumped

down through the Collector Hub, upwards

through the sand bed, and deposited out

of Port D.

Rinse: This function for initial startup,

cleaning, and sand bed leveling after Backwash;

water is pumped downwards through the sand

bed, up through the Collector Hub and

deposited out of the valve Port D.

NOTE:

• Be sure all provisions for wastewater disposal meet applicable local, state or

national codes. Do not discharge water where it will

cause flooding or damage.

• When the Control Valve is set to the Backwash, Rinse, or Drain position, water

will discharge from Port D on the Control Valve.

• Do not switch on or operate the sand filter with the Control Valve set to the

Closed function or it will seriously damage the sand filter.

• Do not set the Control Valve between two functions, or it will lead to leaking.

• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D

before operating the sand filter.

AIR RELEASE

Press down the control valve handle and wait untill the water

flow from Port D to release the air.

NOTE: It is important to repeat this operation every time you

start the pump after winterizing, maintenance and backwashing

the sand bed.

Drain: This function drains water from the

pool; another filter bypass setting, water is

pumped and deposited out of Port D, instead of

returning it to the pool.

Circulate: This function circulates pool

water by passing the sand filter; use this

function if the filter is broken to collect debris

in the Debris Screens.

FIRST TIME USE INSTRUCTIONS

Backwash and Rinsing must be performed to prepare the pump for its first

use and to wash the sand.

CAUTION: DO NOT DRY RUN THE SAND FILTER

1. Press down on the Control Valve handle and rotate to the Backwash

function.

2. Plug in and run the sand filter for 3-5 minutes, or until the water runs clear.

3. Switch off the sand filter and set the Control Valve to the Rinse function.

4. Switch on the sand filter and run the sand filter for 1 min. This circulates

water backwards through the sand

filter and drains water out Port D.

5. Switch off the sand filter. Set the

Control Valve to the Closed function.

6. Top up pool water if required.

IMPORTANT: This procedure

removes water from the pool, which you’ll need to replace.

Switch off the sand filter immediately if water levels near the pool’s Inlet and

Outlet valves.

1. Now the sand filter is ready for use. Set

the Control Valve to the Filter function.

NOTE: To prevent the risk of electrical

shock dry any excess water from yourself

and the sand filter.

2. Switch on the sand filter to run it.

NOTE: The sand filter has now started its

filtering cycle. Check that water is returning

to the pool and take note of the filter pressure on Pressure

Gauge. Generally, the recommended sand filter pressure is

less than 0.45 Bar (6.5 PSI) when it is running.

CAUTION: You must ensure the sand

filter is switched off and unplugged

before any maintenance begins or

severe risk of injury or death exists. As

dirt builds up in the sand filter, the

pressure reading on Pressure Gauge

will increase. When the Pressure

Gauge is 0.45 Bar (6.5 PSI) or higher, or water flow to the

pool is too low, it is time to clean the sand. To clean the sand

bed, follow all instructions outlined previously in: Backwash

and Rinsing.

Backwash Rinsing

FIRST TIME USE INSTRUCTIONS

Backwash and Rinsing must be performed to prepare the pump for its first

use and to wash the sand.

CAUTION: DO NOT DRY RUN THE SAND FILTER

1. Press down on the Control Valve handle and rotate to the Backwash

function.

2. Plug in and run the sand filter for 3-5 minutes, or until the water runs clear.

3. Switch off the sand filter and set the Control Valve to the Rinse function.

4. Switch on the sand filter and run the sand filter for 1 min. This circulates

water backwards through the sand

filter and drains water out Port D.

5. Switch off the sand filter. Set the

Control Valve to the Closed function.

6. Top up pool water if required.

IMPORTANT: This procedure

removes water from the pool, which you’ll need to replace.

Switch off the sand filter immediately if water levels near the pool’s Inlet and

Outlet valves.

SAND FILTER MAINTENANCE

1.6

10 15

1.4

1.2

0.8

0.6

0.4

0.2

psi

bar

1. Switch off the sand filter and set the

Control Valve to the Closed function.

2. Close the connection valves.

3. Remove the Strainer Cover by

unscrewing it.

4. Take out the Strainer, remove any

debris.

5. Put the Strainer back into position.

Ensure the hole in the strainer is

aligned.

6. Ensure the Seal Ring is in place.

Secure the Strainer Cover back.

7. Open the connection valves.

NOTE: The Strainer must be emptied

and cleaned periodically. A dirty or blocked strainer will

reduce the performance of the sand filter.

1. Switch off the sand filter and set Control Valve to the Drain

function.

2. Detach the Hose from the pool’s Port A and sand filter Port

A and attach to Port D.

3. Switch on the sand filter and press the “RESET” button to

run the filter and remove the pool water.

WARNING: DO NOT DRY RUN THE SAND FILTER.

NOTE: Pressure gauge is for maintenance purpose only, and

the pressure gauge value is just for reference, it should not

be used as a precision instrument.

NOTE: We recommend you clean the sand bed once a

month or less regularly depending on how often the pool is

used. Do not clean the sand too frequently.

CLEANING THE STRAINER

LOWERING OR DRAINING POOL WATER

Problems Probable Causes Solutions

Sand is flowing to

the pool

No water flow

Excessive filter

pressure

Control Valve leaks

from the port D

Connectors leak

- Sand is too small

- Move the control valve from the

backwash to the filter function without

stop the sand filter

- The level of the sand is too high

- The skimmer is broken

- Stopper plugs were not removed

- Air was not released

- The control valve is set to Closed

- The strainer is blocked

- Sand filter broken

- Dirty filter

- Calcified sand bed

- Insufficient backwashing

- The pressure gauge is broken

- Control Valve is set between two

functions

- The gasket is broken

- Washer of the connectors not in place

- Washer of the connectors broken

- Loose Hoses

- Recommend 0.45 mm to 0.85 mm #20 silica

sand

- Stop the sand filter every time set the control

valve

- Check if the level of the sand is between the

marked “MAX” and “ MIN” on the collector hub

- Replace the skimmer

- Remove the stopper plugs and insert the

debris screens

- Release the air

- Set to filter function

- Clean the strainer

- Call for service

- Backwash

- Inspect sand and change if necessary

- Backwash until water runs clear

- Replace the pressure gauge

- Set to one function

- Replace the gasket

- Reposition the washer

- Replace the washer

- Tighten them

TROUBLESHOOTING

In areas that have freezing winter temperatures, pool

equipment must be winterized to protect against damage.

Allowing water to freeze will damage the sand filter and void

warranty.

1. Backwash the sand filter.

2. Drain the pool according to the pool owner’s manual.

3. Unscrew the drain valve cap at the bottom of the tank and

release the remaining water.

4. Disconnect the two Hoses from the pool and the sand filter.

5. Completely pour the sand out of the tank and dry all

components.

6. Store the sand filter in a dry location out of child’s reach.

STORAGE

SANDFILTERANLAGE

GEBRAUCHSANLEITUNG

Besuchen Sie den YouTube-Kanal

von Bestway

SICHERHEITSANWEISUNGEN

WARNUNG

WICHTIGE SICHERHEITSANWEISUNGEN BITTE LESEN UND BEACHTEN SIE ALLE

SICHERHEITSBESTIMMUNGEN.

Bei der Installation und der Benutzung von elektrischen Geräten müssen die grundlegenden

Sicherheitsbestimmungen einschließlich der folgenden immer beachtet werden:

• Die Pumpe muss über einen Trenntransformator oder über eine

Fehlerstrom-Schutzeinrichtung (RCD) mit einem Ansprechdifferenzstrom von nicht mehr

als 30mA versorgt werden.

• Die Stromquelle muss mindestens 4 m vom Pool entfernt sein.

• Das Gerät muss von einer geerdete Stromquelle mit Spannung versorgt werden

• ELEKTROSCHOCKGEFAHR - Die Pumpe darf nicht betrieben werden, wenn sich

Personen im Pool aufhalten. Bei defektem Sandfilter darf der Pool nicht genutzt werden.

• VERGRABEN SIE KEINE KABEL. Verlegen Sie die Kabel so, dass die Gefahr einer

Beschädigung durch Rasenmäher, Heckenscheren usw. vermieden wird.

• Ersetzen Sie beschädigte Kabel sofort, um jede Gefahr von elektrischen Schlägen zu

vermeiden.

• Falls das Netzkabel beschädigt ist, muss es durch den Hersteller, den Kundendienst oder

in entsprechender Weise qualifizierte Person ausgewechselt werden, um die Gefahr von

Stromschlägen zu vermeiden.

• Es können keine Verlängerungskabel verwendet werden.

• Elektroschlaggefahr. Der Einsatz des Sandfilters mit einer ungeeigneten Stromversorgung

ist gefährlich und kann zu schweren Funktionsstörungen des Sandfilters führen.

• Entfernen Sie den Erdungsleiter nicht und nehmen Sie keine Änderungen am Stecker vor.

Verwenden Sie keine Adapterstecker. Lassen Sie die Erdung Ihrer Steckdosen von einem

qualifizierten Elektriker überprüfen.

• Behandeln Sie den Sandfilter vorsichtig. Ziehen oder tragen Sie den Sandfilter nicht am

Netzkabel. Ziehen Sie den Stecker nie mit dem Netzkabel aus der Steckdose. Schützen Sie

das Kabel vor Beschädigungen. Der Sandfilter muss vor scharfkantigen Gegenständen, Öl,

beweglichen Teilen und Hitze geschützt werden.

• Trennen Sie dieses Produkt immer von der Stromversorgung, bevor Sie es ausbauen,

reinigen, warten oder Einstellungen daran vornehmen.

• Stecken Sie das Gerät nicht mit nassen Händen ein oder aus.

• Stecken Sie das Gerät immer aus:

• An Regentagen

• Bevor Reinigungs- oder Wartungsarbeiten durchgeführt werden.

• wenn Sie das Produkt für einen längeren Zeitraum unbeaufsichtigt lassen

(z. B. während des Urlaubs)

• Wird das Gerät für einen längeren Zeitraum nicht benutzt (z. B. im Winter), muss das

Poolset demontiert und in Innenräumen gelagert werden.

• Vorsicht: Bitte lesen Sie diese Anweisungen jedes Mal sorgfältig durch, bevor Sie das

Gerät benutzen und installieren/montieren.

• Bewahren Sie diese Anweisungen sorgfältig auf. Beachten Sie bei jedem erneuten Aufbau

des Pools diese Anweisungen.

• Sollten diese Anweisungen verloren gehen, kontaktieren Sie Bestway oder suchen Sie das

Dokument auf unserer Website: www.bestwaycorp.com

• Elektrische Installationen sollten die nationalen Anschlussvorschriften beachten. Lassen

Sie sich von einem qualifizierten Elektriker in allen Fragen beraten.

ACHTUNG: Dieser Sandfilter wurde ausschließlich für die Benutzung in lagerbaren Pools

konzipiert. Nicht in fest installierten Pools benutzen. Ein lagerbarer Pool ist so konstruiert,

dass es zur Lagerung abgebaut und anschließend wieder aufgebaut werden kann. Ein fest

installierter Pool ist so konstruiert, dass es nicht für die Lagerung abgebaut werden kann.

• Dieses Gerät kann von Kindern ab 8 Jahren oder älter sowie von Personen mit

physischen, sensorischen oder mentalen Einschränkungen oder mangelnder Erfahrung

und mangelnden Kenntnissen benutzt werden, sofern sie entsprechend beaufsichtigt oder

mit der Bedienung des Gerätes und den damit verbundenen Gefahren vertraut gemacht

wurden. Kinder dürfen nicht mit dem Gerät spielen. Die Reinigung und Wartung durch den

Benutzer darf von Kindern nicht ohne Beaufsichtigung durchgeführt werden.

• Reinigung und Wartung durch den Benutzer müssen von einem mindestens 18 Jahre

alten Erwachsenen durchgeführt werden, der mit den Gefahren eines elektrischen

Schlages vertraut ist.

HINWEIS:

• Setzen Sie den Sandfilter auf eine feste und ebene Unterlage. Bitte stellen Sie sicher,

dass sich der Sandfilter zumindest 3.5m vom Rand des Pools entfernt befindet. Halten Sie

so viel Abstand wie möglich.

• Achten Sie darauf, dass die Position des Pools und des Sandfilters eine angemessene

Lüftung, die Dränage und den Zugang für die Wartung gewährleistet. Positionieren Sie den

Sandfilter nie an einer Stelle, an der sich Wasser ansammeln kann oder wo er den Verkehr

stört.

• Die Steckdose muss nach der Installation des Pools

zugänglich sein. Die Steckdose des Sandfilters sollte

zumindest 3,5m vom Pool entfernt sein.

• Die Witterungsbedingungen können sich auf die

Leistung und die Lebensdauer des Sandfilters

auswirken; schützen Sie den Sandfilter in geeigneter

Weise vor unnötigem Verschleiß bei kalter oder heißer

Witterung und/oder Sonnenaussetzung.

• Bitte prüfen Sie alle Komponenten des Sandfilters vor

der Benutzung. Bitte wenden Sie sich an den

Bestway-Kundendienst unter der im Handbuch

angegebene Adresse, falls beim Kauf Teile fehlen oder beschädigt sind.

• Defekte Teile müssen unverzüglich ausgetauscht werden. Verwenden Sie ausschließlich

vom Hersteller empfohlene und zugelassene Teile.

• Stellen Sie sicher, dass sich niemand gegen das Gerät lehnt oder darauf setzt.

• Füllen Sie keine Chemikalien in den Sandfilter ein.

• Wenn Chemikalien zum Reinigen des Poolwassers eingesetzt werden, empfehlen wir aus

gesundheitlichen Gründen und zur Einhaltung von Vorschriften die Einhaltung einer

minimalen Filtrierungszeit.

• Bei der Produktinstallation sind nur die vom Hersteller gelieferten oder angegebenen

Medien zu verwenden.

• Es ist unbedingt notwendig zu prüfen, dass die Ansaugöffnungen nicht blockiert sind.

• Es ist empfehlenswert, die Filterung während der Wartungseingriffe auf dem Filtersystem

zu stoppen.

• Regelmäßig das Verstopfen des Filters überwachen.

• Es wird eine wöchentliche Kontrolle für Rückspülen oder Reinigung empfohlen. Die

tägliche Mindestfilterbetriebsdauer von acht Stunden wird empfohlen, um sauberes

Poolwasser zu garantieren.

• Es ist unbedingt notwendig, jegliche beschädigten Elemente oder Elementgruppen so

schnell wie möglich zu ersetzen. Verwenden Sie nur von der Person, die das Produkt auf

den Markt gebracht hat, empfohlen Teile.

• Alle Filter und Filtermedien müssen regelmäßig untersucht werden, um sicherzustellen,

dass keine Schmutzansammlungen vorliegen, die eine korrekte Filterung verhindern. Die

Entsorgung jeglicher gebrauchten Filtermeiden muss in Einklang mit den geltenden

Vorschriften/Gesetzen erfolgen.

• Beachten Sie alle im Handbuch beschriebenen Sicherheitsvorschriften und Empfehlungen.

Im Fall von Zweifeln hinsichtlich der Pumpe oder Umwälzvorrichtungen wenden Sie sich

bitten an einen Installationsfachmann oder an den Hersteller/Importeur/Händler. Die

Installation der Wasserzirkulation muss im Einklang mit den europäischen sowie den

nationalen/lokalen Bestimmungen erfolgen, insbesondere wenn es sich um elektrische

Fragen handelt. Jegliche Änderungen der Ventilposition, Pumpen-oder Gittergröße kann zu

einer Änderung des Durchflusses und einer Erhöhung der Ansauggeschwindigkeit führen.

• Dieses Produkt darf nicht für kommerzielle Zwecke benutzt werden.

BITTE LESEN SIE DAS HANDBUCH SORGFÄLTIG DURCH UND BEWAHREN SIE ES

ALS KÜNFTIGE REFERENZ AUF.

BEWAHREN SIE DIESE ANWEISUNGEN AUF

RCD WARNHINWEISE

WARNUNG: Vergewissern Sie sich, dass die Netzspannung der Steckdose für die Pumpe

geeignet ist, bevor Sie den Netzstecker in dieSteckdose einstecken.

WARNUNG: Gefahr eines elektrischen schlags. Der RCD-Anschluss muss vor jeder

Benutzung getestet werden.

WARNUNG: Schließen Sie den RCD-Stecker an eine Fehlerstrom-Schutzeinrichtung an,

deren Ansprechdifferenzstrom mehr 30mA nicht übersteigt.

WARNUNG: Verwenden Sie die Pumpe nicht, wenn dieser Test scheitert. Wenn Sie Hilfe

benötigen, besuchen Sie bitte den Supportbereich auf unserer Website

www.bestwaycorp.com

WIR EMPFEHLEN, DAS PRODUKT NICHT

BEIM VERKÄUFER ZURÜCKZUGEBEN

FRAGEN? PROBLEME?

FEHLENDE ERSATZTEILE?

Für FAQs, Handbücher, Aufbauvideos

und Ersatzteile gehen Sie auf

bestwaycorp.com/support