LG ABNW12GL5S1 Guide d'installation

P/NO.:MFL68065212

REV.00_190117

www.lg.com

INSTALLATION MANUAL

Ceiling Concealed Duct

AIR

CONDITIONER

Please read this installation manual completely before installing the product.

Installation work must be performed in accordance with the national wiring

standards by authorized personnel only.

Please retain this installation manual for future reference after reading it

thoroughly.

ENGLISH

FRANÇAIS

1,MFL67939925,영어 2017. 7. 17. 오후 2:33 페이지 1

• Do not cool excessively indoors. This may be harmful for your health and may consume more

electricity.

• Block sunlight with blinds or curtains while you are operating the air conditioner.

• Keep doors or windows closed tightly while you are operating the air conditioner.

• Adjust the direction of the air flow vertically or horizontally to circulate indoor air.

• Speed up the fan to cool or warm indoor air quickly, in a short period of time.

• Open windows regularly for ventilation as the indoor air quality may deteriorate if the air condition-

er is used for many hours.

• Clean the air filter once every 2 weeks. Dust and impurities collected in the air filter may block the

air flow or weaken the cooling / dehumidifying functions.

For your records

Staple your receipt to this page in case you need it to prove the date of purchase or for warranty

purposes. Write the model number and the serial number here:

Model number :

Serial number :

You can find them on a label on the side of each unit.

Dealer’s name :

Date of purchase :

Here are some tips that will help you minimize the power consumption when you use the air

conditioner. You can use your air conditioner more efficiently by referring to the instructions

below:

TIPS FOR SAVING ENERGY

ENGLISH

TIPS FOR SAVING ENERGY

2

1,MFL67939925,영어 2017. 7. 17. 오후 2:33 페이지 2

3

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

Always comply with the following precautions to avoid dangerous situations and ensure peak

performance of your product

WARNING

It can result in serious injury or death when the directions are ignored

CAUTION

It can result in minor injury or product damage when the directions are ignored

WARNING

• Installation or repairs made by unqualified persons can result in hazards to you and others.

• Installation of all field wiring and components MUST conform with local building codes or, in

the absence of local codes, with the National Electrical Code 70 and the National Building

Construction and Safety Code or Canadian Electrical code and National Building Code of

Canada.

• The information contained in the manual is intended for use by a qualified service technician

familiar with safety procedures and equipped with the proper tools and test instruments.

• Failure to carefully read and follow all instructions in this manual can result in equipment

malfunction, property damage, personal injury and/or death.

Installation

• Always perform grounding. - Otherwise, it may cause electrical shock.

• For installation of the product, always contact the service center or a professional installation

agency. - Otherwise, it may cause a fire, electrical shock, explosion or injury.

• Securely attach the electrical part cover to the indoor unit and the service panel to the outdoor unit.

- If the electrical part cover of the indoor unit and the service panel of the outdoor unit are not

attached securely, it could result in a fire or electric shock due to dust, water, etc.

• Always install an earth leakage circuit breaker and a dedicated switching board. - No installation may

cause a fire and electrical shock.

• Do not keep or use flammable gases or combustibles near the air conditioner. - Otherwise, it may

cause a fire or the failure of product.

• Ensure that an installation frame of the outdoor unit is not damaged due to use for a long time.

- It may cause injury or an accident.

• Do not disassemble or repair the product randomly. - It will cause a fire or electrical shock.

• Do not install the product at a place that there is concern of falling down. - Otherwise, it may result

in personal injury.

• Use caution when unpacking and installing. - Sharp edges may cause injury.

• Use a vacuum pump or Inert (nitrogen) gas when doing leakage test or air purge. Do not compress

air or Oxygen and Do not use Flammable gases. Otherwise, it may cause fire or explosion. There is

the risk of death, injury, fire or explosion.

• Consult your lacal dealer regarding what to do in case of refrigerant leakage.

When the air conditioner is to be installed in a small room, it is necessary to take proper measures

so that the amount of any leaked refrigerant does not exceed the concentration limit in the event of

a leakage. Otherwise, this may lead to an accident due to oxygen depletion.

• Carry out the specified installation work after taking into account earthquakes.

Failure to do so during installation work may result in the unit falling and causing accidents.

!

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

1,MFL67939925,영어 2017. 7. 17. 오후 2:33 페이지 3

• Make sure that a sekparate power supply circuit is provided for this unit and that all electrical work is

carried out by qualified personnel according to local laws and regulations and this installation manual.

An insufficient power supply capacity or improper electrical construction may lead to electric shocks or fire.

• Be sure to switch off the unit before touching any electrical parts.

• Make sure that all wiring is secured, the specified wires are used, and that there is no strain on the

terminal connections or wires.

• If refrigerant gas leaks during installation, ventilate the area immediately.

Toxic gas may be produced if the refrigerant gas comes into contact with fire.

Operation

• Turn off the unit if strange sounds, smell, or smoke comes from it. - Otherwise, it may cause

electrical shock or a fire.

• Keep the flames away. - Otherwise, it may cause a fire.

• Do not touch the power cable with wet hands when it taking out . – Otherwise, it may cause a fire

or electrical shock.

• Do not open the suction inlet of the indoor/outdoor unit during operation. - Otherwise, it may

electrical shock and failure.

• Do not allow water to run into electrical parts. - Otherwise, it may cause the failure of machine or

electrical shock.

• Never touch the metal parts of the unit when removing the filter. - They are sharp and may cause

injury.

• Do not step on the indoor/outdoor unit and do not put anything on it. - It may cause an injury through

dropping of the unit or falling down.

• When the product is submerged into water, always contact the service center. - Otherwise, it may

cause a fire or electrical shock.

• Take care so that children may not step on the outdoor unit. - Otherwise, children may be seriously

injured due to falling down.

CAUTION

Installation

• Install the drain hose to ensure that drain can be securely done. - Otherwise, it may cause water

leakage.

• Install the product so that the noise or hot wind from the outdoor unit may not cause any damage to

the neighbors. - Otherwise, it may cause dispute with the neighbors.

• Always inspect gas leakage after the installation and repair of product. - Otherwise, it may cause the

failure of product.

• Keep level parallel in installing the product. - Otherwise, it may cause vibration or water leakage.

Operation

• Avoid excessive cooling and perform ventilation sometimes. - Otherwise, it may do harm to your

health.

• Use a soft cloth to clean. Do not use wax, thinner, or a strong detergent. - The appearance of the air

conditioner may deteriorate, change color, or develop surface flaws.

• Do not use an appliance for special purposes such as preserving animals vegetables, precision

machine, or art articles. - Otherwise, it may damage your properties.

• Do not place obstacles around the flow inlet or outlet. - Otherwise, it may cause the failure of

appliance or an accident.

• Do not turn on the breaker or power under condition that front panel, cabinet, top cover, control box

cover are removed or opened.

!

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

4

1,MFL67939925,영어 2017. 7. 17. 오후 2:33 페이지 4

TABLE OF CONTENTS

ENGLISH

5

2 TIPS FOR SAVING

ENERGY

3 IMPORTANT SAFETY

INSTRUCTIONS

6 INTRODUCTION

6 Features

7 INSTALLATION OF

INDOOR

7 Selection of the best location

7 Installation of Unit

10 Indoor Unit Drain Piping

10 Drain test

11 Thermal insulator

11 Wiring Connection

13 INSTALLATION

INSTRUCTION

15 Remote controller installation

16 Group control

17 Installer Setting - How to enter installer

setting mode

18 Installer Setting - Test Run Mode

19 Installer Setting - Setting Address of

Central Control

20 Installer Setting -E.S.P.

21 Installer Setting -Thermistor

22 Installer Setting-Remote Controller

Master/Slave Setup

23 Installer Setting-Celsius / Fahrenheit

Switching

24 Installer Setting - Static Pressure Step

Setting

27 DIP SWITCH SETTING

TABLE OF CONTENTS

1,MFL67939925,영어 2017. 7. 17. 오후 2:33 페이지 5

6

INTRODUCTION

ENGLISH

Features

INTRODUCTION

TEMP

FAN

SPEED

OPER

MODE

Remote

Controller

Air inlet vents

Air outlet

vents

1,MFL67939925,영어 2017. 7. 17. 오후 2:33 페이지 6

INSTALLATION OF INDOOR

ENGLISH

7

Selection of the best location

- The place shall easily bear a load exceeding

four times the indoor unit’s weight.

- The place shall be able to inspect the unit as

the ﬁgure.

- The place where the unit shall be leveled.

- The place shall allow easy water

drainage.(Suitable dimension “H” is neces-

sary to get a slope to drain as ﬁgure.)

- The place shall easily connect with the out-

door unit.

- The place where the unit is not affected by

an electrical noise.

- The place where air circulation in the room

will be good .

- There should not be any heat source or

steam near the unit

- Conﬁrm the positional relationship between

the unit and suspension bolts.

- Thermal insulator the ceiling opening to clean

the ﬁlter or service under the product.

Installation of Unit

Install the unit above the ceiling correctly.

Position of suspension Bolt

- Apply a joint-canvas between the unit and

duct to absorb unnecessary vibration.

- Apply a ﬁlter Accessory at air return hole.

CASE 1

INSTALLATION OF INDOOR

Top view

Unit: mm

Front view

Unit: mm

Front

Inspection hole

600 x 600

Control box

1000

20 or more

Air outlet vents

Air inlet vents

600

(Unit:mm)

A B C D E F G H I J

Dimension

Capacity

(kw)

Drain hole

A

B

J

CD

E

G

F

I

H

ABNW12GL5S1 933 972 388 460 36 190 20 860 148 900

1,MFL67939925,영어 2017. 7. 17. 오후 2:34 페이지 7

8

INSTALLATION OF INDOOR

ENGLISH

- Install the unit leaning to a drainage hole side

as a ﬁgure for easy water drainage.

P

osition of console Bolt

- A place where the unit will be leveled and

that can support the weight of the unit.

- A place where the unit can withstand its

vibration.

- A place where service can be easily per-

formed.

- Select and mark the position for ﬁxing bolts.

- Drill the hole for set anchor on the face of

ceiling.

- Insert the set anchor and washer onto the

suspension bolts for locking the suspension

bolts on the ceiling.

- Mount the suspension bolts to the set

anchor ﬁrmly.

- Secure the installation plates onto the sus-

pension bolts (adjust level roughly) using

nuts, washers and spring washers.

CASE 2

1 Set anchor

Old building New building

2 Plate washer

3 Spring washer

4 Nut

5 Suspension

bolts

CAUTION

Tighten the nut and bolt to prevent unit

falling.

!

M10 Nut

M10 SP. washer

M10 washer

X 4

(Local

supply)

X 4

M10 Nut

M10 SP. washer

M10 washer

X 4

(Local

supply)

X 4

1,MFL67939925,영어 2017. 7. 17. 오후 2:34 페이지 8

INSTALLATION OF INDOOR

ENGLISH

9

CAUTION

• Install declination of the indoor unit is very important for the drain of the duct type air condi-

tioner.

• Minimum thickness of the insulation for the connecting pipe shall be 5mm.

Front of view

• The unit must be declined to the drain hose connected when ﬁnished installation.

!

Drainage hole

U-Trap

B

C

A ≥ 70 mm

B ≥ 2C

C ≥ 2 x SP

SP = External Pressure

(mmAq)

Ex) External Pressure

= 10 mmAq

A ≥ 70 mm

B ≥ 40 mm

C ≥ 20 mm

A

Make sure to be closed.

Unit

Drainage pipe

(Local supply)

Thermal insulator

(Local supply)

• Always lay the drain with downward

inclination (1/100 to 1/50).

Prevent any upward ﬂow or reverse ﬂow

in any part.

• 10 mm or thicker formed thermal insulator

shall always be provided for the drain

pipe.

• Install the P-Trap (or U-Trap) to prevent

a water leakage caused by the blocking

oﬁ ntake air ﬁlter.

Applied U-Trap Dimension

CORRECT

INCORRECT

• Upward routing not

allowed

Caution for gradient of unit and drain piping

Lay the drain hose with a downward inclination so water will drain out.

1,MFL67939925,영어 2017. 7. 17. 오후 2:34 페이지 9

Drainage hole

CORRECT

INCORRECT

1/100~1/50

Ceiling

10

INSTALLATION OF INDOOR

ENGLISH

Maintenance

drain port

Upward

routing

not allowed

Pipe clamp

Indoor unit

Indoor Unit Drain Piping

- Drain piping must have down-slope (1/50 to

1/100): be sure not to provide up-and-down

slope to prevent reversal ﬂow.

- During drain piping connection, be careful

not to exert extra force on the drain port on

the indoor unit.

- The outside diameter of the drain connection

on the indoor unit is 32 mm.

Piping material: Polyvinyl chloride pipe VP-25

and pipe fittings

- Be sure to execute thermal insulator on the

drain piping.

- Install the drain raising pipes at a right

angle to the indoor unit and no more than

300 mm from the unit.

T

hermal insulator material: Polyethylene foam

w ith thickness more than 8 mm.

Drain test

- Connect the main drain pipe to the exterior

and leave it provisionally until the test comes

to an end.

- Feed water to the ﬂexible drain hose and

check the piping for leakage.

- When the test is complete, connect the ﬂexi-

ble drain hose to the drain port on the indoor

unit.

1 Remove the air ﬁlter.

2 Check the drain.

- Spray one or two glasses of water upon

the evaporator.

- Ensure that water ﬂows drain hose of

indoor unit without any leakage.

Feed water

Flexible drain hose

(accessory)

Main

drain pipe

Glue the join

t

Air ﬁlters

1,MFL67939925,영어 2017. 7. 17. 오후 2:34 페이지 10

INSTALLATION OF INDOOR

ENGLISH

11

Thermal insulator

1 Use the thermal insulator material for the

refrigerant piping which has an excellent

heat-resistance (over 120 °C).

2 If this air conditioner is operated for a long

time in high humid atmosphere (dew point

temperature: more than 23 °C), water

drops are liable to fall. In this case, add

thermal insulator material according to the

following procedure:

- Thermal insulation material to be pre-

pared... Adiabatic glass wool with thick-

ness 10 to 20 mm.

- Stick glass wool on all air conditioners

that are located in ceiling atmosphere.

Wiring Connection

- Open the control box cover and connect the

Remote controller cable and Indoor power

wires.

- Remove the control box cover for electrical

connection between the indoor and outdoor

unit. (Remove screws ①.)

- Use the cord clamper to ﬁx the cable.

Control box

Control terminal board

Remote controler cable

Connection cable between

the indoor unit and

the outdoor unit

Indoor unit

Outdoor unit

POWER SUPPLY

1(L) 2(N) 3

1(L) 2(N) 31(L) 2(N)

CAUTION

• The connecting cable connected to the

indoor and outdoor unit should be com-

plied with the following speciﬁcations

(Rubber insulation, type H05RN-F

approved by HAR or SAA).

• If the supply cable is damaged, it must

be replaced by a special cable or assem-

bly available from the manufacturer of

its service agent. When the connection

line between the indoor unit and out-

dooor unit and outdoor unit is over 40 m,

connect the telecommunication line and

power line separately.

!

20 mm

GN/YL

NORMFAL

CROSS-SECTIONAL

AREA :

1 Phase Model : 0.75mm

2

Indoor unit

Thermal insulator

(accessory)

Fastening band

(accessory)

Refrigerant

piping

Control box cover

(On which the Electric

Wiring Connection is put)

1

1,MFL67939925,영어 2017. 7. 17. 오후 2:34 페이지 11

12

INSTALLATION OF INDOOR

ENGLISH

CAUTION

Precautions when laying power wiring

Use round pressure terminals for connec-

tions to the power terminal block.

When none are available, follow the

instructions below.

• Do not connect wiring of different thick-

nesses to the power terminal block.

(Slack in the power wiring may cause

abnormal heat.)

• When connecting wiring which is the

same thickness, do as shown in the fig-

ure below.

• For wiring, use the designated power

wire and connect firmly, then secure to

prevent outside pressure being exerted

on the terminal block.

• Use an appropriate screwdriver for tight-

ening the terinal screws. A screwdriver

with a small head will strip the head and

make proper tighterning impossible.

• Over-tightening the terminal screws

may break them.

!

Round pressure terminal

Power wiring

1,MFL67939925,영어 2017. 7. 17. 오후 2:34 페이지 12

INSTALLATION INSTRUCTION

ENGLISH

13

INSTALLATION INSTRUCTION

1 Please fix tightly using provided screw

after placing remote controller setup board

on the place where you like to setup.

- Please set it up not to bend because poor

setup could take place if setup board

bends.

Please set up remote controller board fit

to the reclamation box if there is a recla-

mation box.

2 Can set up wired remote controller cable

into three directions.

- Set up direction: the surface of wall recla-

mation, upper, right

- If setting up remote controller cable into

upper and right side, please set up after

removing remote controller cable guide

groove.

* Remove guide groove with long nose.

① Reclamation to the surface of the wall

② Upper part guide groove

③ Right part guide groove

1,MFL67939925,영어 2017. 7. 17. 오후 2:34 페이지 13

14

INSTALLATION INSTRUCTION

ENGLISH

CAUTION

• When installing the wired remote con-

troller, do not bury it in the wall. (It can

cause damage in the temperature sen-

sor.)

• Do not install the cable to be 50 m(164 ft)

or longer. (It can cause communication

error.)

!

3 Please fix remote controller upper part into

the backplate attached to the surface of

the wall, as the picture below, and then,

connect with backplate by pressing lower

part.

- Please make sure to leave no gaps on the

top, bottom, left or right sides between

the remote controller and backplate.

- Before assembly with the backplate,

arrange the Cable not to interfere with cir-

cuit parts.

Remove remote controller by inserting a

screwdriver into the lower separating holes

and twisting to release the controller from

backplate.

- There are two separating holes. Please

individually separate one at a time.

- Please be careful not to damage the

inside components when separating.

4 Please refer to the following directions

when connecting the indoor unit and the

wired remote controller together.

- Please connect the cables as shown in

the figure below when connecting the

plug type cable from the indoor unit’s

C/BOX and the housing type of the exten-

sion cable.

5

Please use an extension cable if the distance

between the wired remote controller and the

indoor unit is longer than 10 m(32 ft).

Wall

Side

Wall

Side

Please check if the connectors

are connected properly.

C/BOX Cable (Plug type)

Extension cable(housing type)

Indoor

Unit side

TEMP

FAN

SPEED

OPER

MODE

Wall

Side

Wall

Side

CAUTION

• Specification of LG supplied extension

cable: AWG#22, 3 core shielded.

(Model : PZCWRC1)

* Apply enclosed noncombustible con-

duit(metal raceway) totally or use FT-6

rated cable or above level in case of local

electric & building code that requires

plenum (CMP) cable usage.

• AWG#22, 3 core shielded is recom-

mended when using the large hole in the

center of the back plate.

• AWG#24, 3 core shielded is recom-

mended when using the side or top

knock-out of the back plate.

!

Signal Yellow

12 V Red

GND Black

1,MFL67939925,영어 2017. 7. 17. 오후 2:34 페이지 14

INSTALLATION INSTRUCTION

ENGLISH

15

Remote controller installation

Since the room temperature sensor is in the remote controller, the remote controller box should

be installed in a place away from direct sunlight, high humidity and direct supply of cold air to

maintain proper space temperature. Install the remote controller about 5 ft(1.5 m) above the floor

in an area with good air circulation at an average temperature.

Do not install the remote controller where it can be affected by:

- Drafts, or dead spots behind doors and in corners.

- Hot or cold air from ducts.

- Radiant heat from sun or appliances.

- Concealed pipes and chimneys.

- Uncontrolled areas such as an outside wall behind the remote controller.

- This remote controller is equipped with LCD. display. For proper display of the remote controller

LCD's, the remote controller should be installed properly as shown in Fig.1.

(The standard height is 4~5 ft (1.2~1.5 m) from floor level.)

TEMP

FAN

SPEED

OPER

MODE

TEMP

FAN

SPEED

OPER

MODE

TEMP

FAN

SPEED

OPER

MODE

TEMP

FAN

SPEED

OPER

MODE

5 ft

(1.5 m)

(Fig. 1)

Direct

Sun ray contact area

no

yes

1,MFL67939925,영어 2017. 7. 17. 오후 2:34 페이지 15

16

INSTALLATION INSTRUCTION

ENGLISH

Group control

1 When installing more than 2 units of air

conditioner to one wired remote controller,

please connect as the right figure.

- If it is not event communication indoor

unit, set the unit as slave.

- Check for event communication through

the product manual.

When controlling multiple indoor units with

event communication function with one

remote controller, you must change the

master/slave setting from the indoor unit.

Indoor units, the master/slave configura-

tion of the product after completion of

indoor unit power ‘OFF’ and then ‘ON’ the

power after 1 minutes elapsed sign up.

- For ceiling type cassette and duct product

group, change the switch setting of the

indoor PCB.

- For wall-mount type and stand type prod-

uct, change the master/slave setting with

the wireless remote controller. (Refer to

wireless remote controller manual for

detail)

* When installing 2 remote controllers to

one indoor unit with event communica-

tion function, set the master/slave of the

remote controller. (Refer to remote con-

troller master/slave selection)

When controlling the group, some func-

tions excluding basic operation setting, fan

level Min/Mid/Max, remote controller lock

setting and time setting may be limited.

2 When installing more than 2 wired remote

controllers to one air conditioner, please

connect as the right picture.

- When installing more than 2 units of

wired remote controller to one air condi-

tioner, set one wired remote controller as

master and the others all as slaves, as

shown in the right picture.

- You cannot control the group as shown in

the right for some products.

- Refer to the product manual for more

detail.

- When controlling in groups, set the mas-

ter/slave of the remote controller.

Refer to Installer setting section on how

to set master/slave for more detail.

GND

12V

Signal wire

TEMP

FAN

SPEED

ROOM

TEMP

GND

12V

B Y R B Y R

MASTER SLAVE

Signal wire

GND

12V

Signal wire

TEMP

FAN

SPEED

ROOM

TEMP

FAN

SPEED

ROOM

TEMP

#3 switch OFF: Master

(Factory default setting)

#3 switch ON: Slave

1,MFL67939925,영어 2017. 7. 17. 오후 2:34 페이지 16

INSTALLATION INSTRUCTION

ENGLISH

17

Installer Setting - How to enter installer setting mode

CAUTION

Installer setting mode is to set the detail function of the remote controller.

If the installer setting mode is not set correctly, it can cause problems to the product, user

injury or property damage. This must be set by an certificated installer, and any installation

or change that is carried out by a non-certificated person should be responsible for the

results. In this case, free service cannot be provided.

!

TEMP

FAN

SPEED

OPER

MODE

Function Code

Value

If you want to set installer setting mode,

Press the Temperature up button and the oper

mode button same time for five seconds.

1

When you enter the setting mode

Initially. Function code is displayed

on the LCD screen.

2

General air-conditioner product

No. Function Code Value

1 Test Run 01 01:Set

2 Address Setting 02 00~FF : Address

01:VeryLow 0 ~ 255

02:Low

3 E.S.P. Value 03

03:Med

04:High

05:Very High

01:Remo

4 Thermistor 04 02:Indoor

03:2TH

01:Med

02:Low

5 Ceiling Height 05

03:High

04:Very High

01:V-H

02:F-H

6 Static Pressure 06

03:V-L

04:F-L

7 Master Setting 07

00:Slave

01:Master

8

Celsius

12

00:Celsius

(Optimized only for U.S.A)

Fahrenheit Switching 01:Fahrenheit

9

Static Pressure

32

00: use static pressure (code 06) set value

Step 01~ 11: static pressure step (code 32) set value

Function Code ESP valueESP step

* Some contents may not be displayed depending on the product function

1,MFL67939925,영어 2017. 7. 17. 오후 2:34 페이지 17

18

INSTALLATION INSTRUCTION

ENGLISH

Installer Setting - Test Run Mode

After installing the product, you must run a Test Run mode.

For details related to this operation, refer to the product manual.

TEMP

FAN

SPEED

OPER

MODE

When pressing the button and

button simultaneously for more than 3

seconds, the system will be entered

into the installer setting mode.

- After entering into the installer setting

mode, select the test run mode code

value by pressing the button.

* Test run mode code value : 01

1

When pressing the button, the test

operation mode will be performed, and it

is displayed as shown in the left figure.

2

When pressing the button and

button simultaneously for more than 3

seconds after the setting has been

completed, the setting mode will be

released.

- If there isn’t any button input for

more than 25 seconds, the installer

setting mode will also be released.

3

When approx. 18 minutes are elapsed

after starting of the test oper-mode, the

system will be stopped automatically

and converted to the standby state.

- If any button is inputted during the

test run mode, the test run mode will

be forced to be relreased.

4

OPER

MODE

OPER

MODE

OPER

MODE

OPER

MODE

What is the test run mode?

- This means the operation of the product under the cooling, strong wind, and Comp on state

without performing room temperature control in order to confirm the installed state during the

product installation.

1,MFL67939925,영어 2017. 7. 17. 오후 2:34 페이지 18

INSTALLATION INSTRUCTION

ENGLISH

19

Installer Setting - Setting Address of Central Control

It's the function to use for connecting central control.

Please refer to central controller manual for the details

TEMP

FAN

SPEED

OPER

MODE

When pressing the button and

button simultaneously for more than 3

seconds, the system will be entered into the

installer setting mode.

-

After entering into the installer setting mode,

select the central control address setting

code value by pressing the button.

* Setting address of central control code

value : 02

1

When pressing the button, the system

will be set up with the address value which

has been established at present.

3

When pressing the button and

button simultaneously for more than 3

seconds after the setting has been completed,

the setting mode will be released.

- If there isn’t any button input for more than

25 seconds, the installer setting mode will

also be released.

4

Set up the group number and indoor unit with

the temperature adjustment(▲,▼) buttons.

For example, when setting as

[ Group number=2 Indoor number=3 ]

it will be displayed as shown in the left figure.

2

OPER

MODE

OPER

MODE

TEMP

Group number

Indoor unit number

OPER

MODE

- If you connect the indoor unit to the central controller, you should set the network address of

the indoor unit so that the central controller could recognize it.

- The center-control address is composed of the group number and the indoor-unit number.

NOTE

!

The remote controller displays 'HL' if central controller has locked the remote controller .

In the case when the lock is set up at the central controller, ‘HL’ will be indicated on the dis-

play window of the wired remote controller and the indoor unit will not be controlled by the

remote controller.

1,MFL67939925,영어 2017. 7. 17. 오후 2:34 페이지 19

20

INSTALLATION INSTRUCTION

ENGLISH

Installer Setting -E.S.P.

This is the function that decides the strength of the wind for each wind level and because this

function is to make the installation easier.

- If you set ESP incorrectly, the air conditioner may malfunction.

- This setting must be carried out by a certificated-technician.

TEMP

FAN

SPEED

OPER

MODE

When pressing the button and

button simultaneously for more than 3

seconds, the system will be entered into

the installer setting mode.

- After entering into the installer setting

mode, select the E.S.P code value by

pressing the button.

* E.S.P code value : 03

1

Select the desired air flow rate with

the button. Whenever pressing

the button, [Lo→Med→Hi] will be

indicated.

2

Select the desired air flow rate value with

the temperature up(▲), down(▼) button.

* E.S.P value range : 0~255

- E.S.P value will be indicated at the upper

right section of the display window.

3

When pressing the button, currently

established E.S.P value will be set up.

4

When pressing the button and

button simultaneously for more than 3

seconds after the setting has been

completed, the setting mode will be

released.

- If there isn’t any button input for more

than 25 seconds, the installer setting

mode will also be released.

5

OPER

MODE

OPER

MODE

FAN

SPEED

FAN

SPEED

OPER

MODE

- Precaution shall be taken not to alter the E.S.P value corresponded to each air flow section.

- E.S.P value can be varied according to the products.

- In the case of going to the next air flow rate stage by pressing the fan-speed button during the

setup of the E.S.P value, the E.S.P value of previous air flow rate will be maintained by remem-

bering the E.S.P value prior to the shift.

1,MFL67939925,영어 2017. 7. 17. 오후 2:34 페이지 20

La page charge ...

LG ABNW12GL5S1 Guide d'installation

Ce manuel convient également à

LG ABNW12GL5S1 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents