Bolens 31AM2P5B565 Le manuel du propriétaire

Marque: Bolens

Modèle: 31AM2P5B565

Catégorie: Accessoires pour véhicules automobiles

Taper: Le manuel du propriétaire

Ce manuel convient également à

Safety • Operation • Maintenance • Storage • Troubleshooting

READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION

IMPORTANT:

PRINTED IN U.S.A. MTD Products Ltd., P. O. Box 1386, KITCHENER, ONTARIO N2G 4J1

179cc and 208cc

Horizontal Shaft OHV Snow Engines

11 / 5 / 20 0 7

769-03333A

OPERATOR’S MANUAL

Table of Contents

This manual covers the operation and maintenance of your

engine. All information in this publication is based on the latest

product information available at the time of printing.

No part of this publication may be reproduced without written

permission.

This manual should be considered a permanent part of the

engine and should remain with it if it is resold.

This Operator’s Manual is an important part of your new engine. It will help you prepare and maintain the unit for best

performance. Please read and understand what it says.

Safe Operation Practices .........................................4

Operating the Engine ...............................................6

Maintaining the Engine ...........................................10

Troubleshooting ................................................. ....13

Emission Control System Warranty Statement ......14

Pay special attention to safety messages and notes printed in

this manual and on the engine itself. A safety message alerts

you to potential hazards that could hurt you or others.

WARNING: Indicates a strong possibility of

severe personal injury or death if instructions

are not followed. Each safety message is

preceded by a safety symbol.

NOTE: Gives helpful information.

IMPORTANT: Indicates a possibility of equip-

ment or property damage if instructions are

not followed.

WARNING: The engine is designed to give safe and dependable service if operated according to instructions. Read

and understand the Operator’s Manual before operating the engine. Failure to do so could result in personal injury or

equipment damage.

This Operator’s Manual may cover a range of engine models. Characteristics and features discussed and/or illustrated in this manual may not be

applicable to all engine models. MTD LLC reserves the right to change product specifications, designs, and equipment without notice and without

incurring obligation.

Visit www.mtdcanada.ca or call a Customer Support Representative at 1-800-668-1238.

Customer Support

Engine

Safe

Operation

Practices

Gasoline and its vapors are

extremely flammable and

explosive. Fire or explosion can

cause severe burns or death. If

gasoline is spilled on yourself

or your clothes, wash your skin

and change clothes immediately.

• When adding fuel, turn engine OFF and let engine

cool at least 2 minutes before removing gas cap.

• Fill fuel tank outdoors or in well ventilated area.

• Use only an approved gasoline container.

• Never fill containers inside a vehicle or on a truck or

trailer bed with a plastic liner. Always place contain-

ers on the ground away from your vehicle before

filling.

• If possible, remove gas-powered equipment from the

truck or trailer and refuel it on the ground. If this is

not possible, then refuel such equipment on a trailer

with a portable container, rather than from a gasoline

dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel

tank or container opening at all times until fueling is

complete. Do not use a nozzle lock-open device.

• Do not overfill fuel tank. Fill tank to approximately

2 cm below lowest portion of neck to allow for fuel

expansion.

• Keep gasoline away from sparks, open flames, pilot

lights, heat, and other ignition sources.

• Never fuel equipment indoors because flammable

vapors will accumulate in the area.

• Extinguish all cigarettes, cigars, pipes, and other

sources of ignition.

• Check fuel line, tank, cap, and fittings frequently for

cracks or leaks. Replace if necessary.

• When starting engine, make sure spark plug, muffler,

fuel cap and air cleaner are in place.

• Do not crank engine with spark plug removed.

• If fuel spills, wait until it evaporates before starting

engine.

• When operating equipment, do not tip engine or

equipment at angle which causes gasoline to spill.

• Do not choke carburetor to stop engine.

• When transporting equipment, transport with fuel tank

EMPTY.

• When storing gasoline or equipment with fuel in tank,

store away from furnaces, stoves, water heaters or

other appliances that have pilot light or other ignition

source because they can ignite gasoline vapors.

Starting engine creates spark-

ing. Sparking can ignite nearby

flammable gases. Explosion and

fire could result.

• If there is a natural or LP gas leakage in area, do not

start engine.

• Do not use pressurized starting fluids because vapors

are flammable.

Engines give off carbon mon-

oxide, an odorless, colorless,

poisonous gas. Breathing carbon

monoxide can cause nausea,

fainting, or death.

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if

doors or windows are open.

Unintentional sparking can result

in fire or electric shock. Unin-

tentional start-up can result in

entanglement, traumatic amputa-

tion, or laceration.

• Before peforming adjustments or repairs, disconnect

spark plug wire and keep it away from spark plug.

• When testing for spark, use approved spark plug

tester.

• Do not check for spark with spark plug removed.

WARNING: Gasoline and its vapors are extremely flammable and explosive. Fire or

explosion can cause severe burns or death. If gasoline is spilled on yourself or your

clothes, wash your skin and change clothes immediately.

WARNING

Gasoline and its vapors

are extremely flam-

mable and explosive.

Fire or explosion can

cause severe burns

or death. If gasoline is

spilled on yourself or

your clothes, wash your

skin and change clothes

immediately.

Starting engine creates

sparking. Sparking can

ignite nearby flamma-

ble gases. Explosion

and fire could result.

Unintentional sparking

can result in fire or

electric shock. Unin-

tentional start-up can

result in entanglement,

traumatic amputation,

or laceration.

Running engine produces heat.

Engine parts, especially muffler,

become extremely hot. Severe

thermal burns can occur on

contact. Combustible debris,

such as leaves, grass, brush, etc.,

can catch fire.

• Allow muffler, engine cylinder, and fins to cool before

touching.

• Keep children away from hot or running engines. They

can suffer burns from a hot muffler.

• Remove accumulated combustibles from muffler and

cylinder area.

Rotating engine parts can

contact or entangle hands, feet,

hair, clothing, or accessories.

Traumatic amputation or severe

laceration can result.

• Operate equipment with guards in place.

• Keep hands and feet away from rotating parts.

• Tie up long hair and remove jewelry.

• Do not wear loose-fitting clothing, dangling draw

strings or items that could become caught.

Rapid retraction of starter cord

(kickback) will pull hand and

arm toward engine faster than

you can let go. Broken bones,

fractures, bruises or sprains

could result.

• When starting engine, pull cord slowly until resis-

tance is felt, then pull rapidly.

• Remove all external equipment/engine loads before

starting engine.

• Direct coupled equipment components such as, but

not limited to blades, impellers, pulleys, sprockets,

etc., must be securely attached.

Safety Label Location

This label warns you of potential hazards that can cause

serious injury. Read it carefully. See Figure 8-1 for

explanation of symbols.

If the label comes off or becomes hard to read, contact

the dealer for replacement.

Engine

Safe

Operation

Practices

WARNING

Running engine

produces heat. Engine

parts, especially muf-

fler, become extremely

hot. Severe thermal

burns can occur on

contact. Combustible

debris, such as leaves,

grass, brush, etc., can

catch fire.

Rotating engine parts

can contact or entangle

hands, feet, hair, cloth-

ing, or accessories.

Traumatic amputation

or severe laceration

can result.

Rapid retraction of

starter cord (kickback)

will pull hand and

arm toward engine

faster than you can

let go. Broken bones,

fractures, bruises or

sprains could result.

2UN

3TART

4OXIC&UMES

(OT3URFACE

3AFETY!LERT

5NLEADED&UEL

-ANUAL

2EAD/WNERS

'ASOLINE)S

&LAMMABLE

0 "

International Symbols and Meanings

Figure 8-1

Primer

Depressing primer forces fuel directly into

engine’s carburetor to aid in cold-weather

starting.

Ignition Key

The ignition key is a safety device.

Insert key and snap in place; do not

turn ignition key. Pull the key out

halfway to stop the engine. Remove

key when the unit is not in use.

Throttle

The throttle control regulates the speed of the engine

and will shut off the engine when moved into the STOP

position.

Choke

Activating the choke closes the choke

plate on the carburetor and aids in

starting the engine. For information

on choke usage, see “Starting The

Engine.”

Starter Handle

This motor is fitted with a recoil action pull start and a

mitten grip handle for easy access while wearing gloves

or mittens.

Engine Components

Oil Drain

Removing the oil drain plug will drain the oil from the

engine. Refer to the Maintenance section in this manual

for instructions on changing the oil.

Oil Filler Cap/Dipstick

Remove oil cap to check oil level. Refer to “Pre-Operation

Check” section for checking oil and “Maintaining Your

Engine” section for adding oil instructions.

Fuel Fill Cap

Remove gas cap to add fuel. Unit runs on automotive

unleaded gas.

Electric Start (if equipped)

Electric Switch Box

Requires the use of a three-prong outdoor extension cord

and a 120V power source/wall outlet.

Electric Start Button

Pressing the electric starter button engages the engine’s

electric starter when plugged into a 120V power source.

Read this section before starting the engine. It is important to familiarize yourself with the controls on the engine. Refer

to “Starting the Engine” section for detailed operating instructions.

Operating

the

Engine

IMPORTANT: This engine

is shipped without gaso-

line or oil in the engine.

Running the engine with

insufficient oil can cause

serious engine damage

and void the engine

warranty.

Specifications are

subject to change without

notification or obligation.

Images my not reflect your

exact model and are for

reference purposes only.

Figure 2-1: Front and rear views of the engine.

* Optional

PRIMER

Spark Plug

Starter Handle

Oil Drain

Mufﬂer

Oil Filler Cap/Dipstick

Electric start button*

Electric Switch Box*

Fuel Fill Cap

Primer

Ignition Key

Throttle

Choke

Checking the Fuel Level

IMPORTANT: Before refueling, allow engine to cool

two minutes.

Clean around fuel fill before removing cap to fuel.

A fuel level indicator is located in the fuel tank. Fill

tank until fuel reaches the fuel level indictor, Figure

2-4. Be careful not to overfill.

Pre-Operation Check

IMPORTANT: This engine is shipped without gaso-

line or oil in the engine. Running the engine with

insufficient oil can cause serious engine damage

and void the engine warranty.

Oil Recommendations

Before starting engine, fill with oil, refer to viscosity

chart in Figure 2-2. Engine oil capacity is 600 ml. Do not

over-fill. Use a 4-stroke, or an equivalent high detergent,

premium quality motor oil certified to meet or exceed

U.S. automobile manufacturer’s requirements for service

classification SG, SF. Motor oils classified SG, SF will

show this designation on the container.

IMPORTANT: DO NOT use nondetergent oil or

2-stroke engine oil. It could shorten the engine’s

service life.

Checking Oil Level

IMPORTANT: Be sure to check the engine on a level

surface with the engine stopped.

Remove the oil filler cap/dipstick and wipe the

dipstick clean, Figure 2-3.

Insert the cap/dipstick into the oil filler neck, but do

not screw it in.

Remove the oil filler cap/dipstick. If the level is low,

slowly add oil until oil level registers between high

(H) and low (L), Figure 2-3.

Replace and tighten cap/dipstick firmly before

starting engine.

IMPORTANT: Do not overfill. Overfilling with oil may

cause smoking, hard starting, or spark plug fouling.

Fuel Recommendations

Use automotive gasoline (unleaded or low leaded to

minimize combustion chamber deposits) with a minimum

of 87 octane. Gasoline with up to 10% ethanol or 15%

MTBE (Methyl Tertiary Butyl Ether) can be used. Never

use an oil/gasoline mixture or dirty gasoline. Avoid

getting dirt, dust, or water in the fuel tank. DO NOT use

E85 gasoline.

WARNING: Gasoline is extremely flam-

mable and is explosive under certain

conditions.

Refuel in a well-ventilated area with the engine

stopped. Do not smoke or allow flames or sparks

in the area where the engine is refueled or where

gasoline is stored.

Do not overfill the fuel tank. After refueling, make

sure the tank cap is closed properly and securely.

Be careful not to spill fuel when refueling. Spilled

fuel or fuel vapor may ignite. If any fuel is spilled,

make sure the area is dry before starting the engine.

Avoid repeated or prolonged contact with skin or

breathing of vapor.

•

Operating

the

Engine

WARNING

WARNING: Gasoline is

extremely flammable and

is explosive under certain

conditions.

WARNING: Always keep

hands and feet clear of

equipment moving parts.

Do not use a pressurized

starting fluid. Vapors are

flammable.

Figure 2-3: Checking the oil level.

Figure 2-4: The fuel level indicator

Fuel Level Indicator

Top View

Fill

between

high

and low

marks

Figure 2-2: Oil Viscosity Chart

-30º -20º -10º 0º

0º 20º 40º-20º

5W-30

0W-30

-40º

Synthetic

Operating

the

Engine

IMPORTANT: This engine

is shipped without gaso-

line or oil in the engine.

Running the engine with

insufficient oil can cause

serious engine damage and

void the engine warranty.

WARNING: The optional

electric starter is equipped

with a grounded three-wire

power cord and plug, and is

designed to operate on 120

volt AC household current.

It must be used with a prop-

erly grounded three-prong

receptacle at all times to

avoid the possibility of

electric shock.

WARNING

Starting the Engine

WARNING: Always keep hands and

feet clear of moving parts. Do not use

a pressurized starting fluid. Vapors are

flammable.

NOTE: Allow the engine to warm up for a few min-

utes after starting. The engine will not develop full

power until it reaches operating temperatures.

Engines with Electric Starters

WARNING: The electric starter is

equipped with a grounded three-wire

power cord and plug, and is designed

to operate on 120 volt AC household

current. It must be used with a properly grounded

three-prong receptacle at all times to avoid the

possibility of electric shock. Follow all instructions

carefully prior to operating the electric starter.

WARNING: DO NOT use electric starter

in rain.

Determine that your home’s wiring is a three-wire

grounded system. Ask a licensed electrician if you

are unsure. If you have a grounded three-prong

receptacle, proceed as follows. If you do not have

the proper house wiring, DO NOT use the electric

starter under any conditions.

Insert ignition key fully into slot, Figure 2-5. Make

sure it snaps into place. DO NOT turn ignition

key. The engine cannot start unless the key is

inserted into ignition switch.

Plug the extension cord into the electric switch box

located on the engine, Figure 2-6. Plug the other

end of extension cord into a three-prong 120-volt,

grounded, AC outlet in a well-ventilated area.

Move throttle control, Figure 2-1, to FAST (rabbit)

position.

Move choke to the ON position (cold engine start).

If engine is warm, place choke in OFF position,

Figure 2-1.

Push primer three to five (3-5) times, making sure

to cover vent hole when pushing, Figure 2-1. If

engine is warm, push primer only once. Always

cover vent hole when pushing. Cool weather may

require priming to be repeated.

Push starter button to start engine, Figure 2-1.

Once the engine starts, immediately release

starter button. Electric starter is equipped with

thermal overload protection; system will temporarily

shut-down to allow starter to cool if electric starter

becomes overloaded.

Figure 2-5: The ignition key is a safety device.

Figure 2-6: Plug cord into electric switch box on engine.

As the engine warms, slowly rotate the choke control

to OFF position. If the engine falters, restart engine

and run with choke at half-choke position for a short

period of time, and then slowly rotate the choke into

OFF position.

After engine is running, disconnect power cord from

electric starter. When disconnecting, always unplug

the end at the wall outlet before unplugging the

opposite end from the engine.

Engines with Starter Handle

(non-electric start)

IMPORTANT: Do not pull the starter handle with

engine running.

Insert ignition key fully into slot, Figure 2-4. Make

sure it snaps into place. DO NOT turn ignition key.

The engine cannot start unless the key is inserted

into ignition switch.

Move throttle, Figure 2-1, control to FAST (rabbit)

position.

Move choke, Figure 2-1, to the ON position (cold

engine start). If engine is warm, place choke in OFF

position.

Push primer three to five (3-5) times, making sure to

cover vent hole when pushing, Figure 2-1. If engine

is warm, push primer only once. Always cover vent

hole when pushing. Cool weather may require

priming to be repeated.

Pull gently on the starter handle until it begins to

resist, then pull quickly and forcefully to overcome

the compression. Do not release the handle and al-

low it to snap back. Return rope SLOWLY to original

position. If required, repeat this step.

As the engine warms, slowly rotate the choke

control to OFF position. If the engine falters, restart

engine and run with choke at half-choke position

for a short period of time, and then slowly rotate the

choke into OFF position.

Stopping the Engine

WARNING: To avoid unsupervised en-

gine operation, never leave the engine

unattended while running. Turn the

engine off after use and remove ignition key

Run engine for a few minutes before stopping to help dry

off any moisture on the engine.

Move throttle control to STOP position.

Remove the ignition key. Removing the key will

reduce the possibility of unauthorized starting of the

engine while equipment is not in use. Keep the key

in a safe place. The engine cannot start without

the ignition key.

Wipe any moisture away from the controls on the

engine.

Operating

the

Engine

WARNING: To avoid

unsupervised engine

operation, never leave the

engine unattended while

running. Turn the engine

off after use and remove

ignition key

WARNING

IMPORTANT: Do not allow

the starter handle to snap

back against the engine.

Return it gently to prevent

damage to the starter.

Tasks First 5

Hrs.

Each Use or

Every 5 Hrs.

Every Season

or 25 Hrs.

Every Season

or 50 Hrs.

Every Season

or 100 Hrs.

Service Dates

Check engine oil

Change engine oil

Check spark plug

Service spark plug

Clean exhaust area

NOTE: Please dispose of used motor oil in a manner

that is compatible with the environment. We suggest

you take it in a sealed container to your local service

station for reclamation. Do not throw it in the trash or

pour it on the ground.

Oil Service

Check oil level regularly.

Be sure correct oil level is maintained. Check every

five hours or daily before starting engine. See oil

checking procedure in the Operation section.

Oil Change

IMPORTANT: Be sure to check engine on a level

surface with the engine stopped. Drain the oil while

the engine is still warm to assure rapid and complete

draining.

Drain fuel from tank by running engine until the fuel

tank is empty. Be sure fuel fill cap is secure.

Place suitable oil collection container under oil drain

plug.

Remove oil drain plug, Figure 3-1.

Tip engine to drain oil into the container. Used oil

must be disposed of at a proper collection center.

Reinstall the drain plug and tighten it securely.

Refill with the recommended oil and check the oil

level, refer to Operation section for instructions.

Reinstall the oil filler cap/dipstick securely.

IMPORTANT: Used motor oil may cause skin cancer

if repeatedly left in contact with the skin for pro-

longed periods. Although this is unlikely unless you

handle used oil on a daily basis, it is still advisable

to thoroughly wash your hands with soap and water

as soon as possible after handling used oil.

•

WARNING: Shut off the engine before

performing any type of maintenance.

To prevent accidental start-up, discon-

nect the spark plug boot.

IMPORTANT: If engine must be tipped to transport

equipment or to inspect, keep spark plug side of en-

gine up. Transporting or tipping engine with spark

plug down may cause smoking, hard starting, spark

plug fouling, or oil saturation of air cleaner.

Periodic inspection and adjustment of the engine is

essential if high level performance is to be maintained.

Regular maintenance will also ensure a long service life.

The required service intervals and the type of mainte-

nance to be performed are described in the table below.

Follow the hourly or calendar intervals, whichever occur

first. More frequent service is required when operating in

adverse conditions.

Maintenance Schedule

Maintaining

the

Engine

WARNING

WARNING: Shut off the

engine before performing

any type of maintenance.

To prevent accidental

start-up, disconnect the

spark plug boot.

Before tipping engine or

equipment to drain oil,

drain fuel from tank by

running engine until fuel

tank is empty.

IMPORTANT: Be sure to

check engine on a level

surface with the engine

stopped. Drain the oil

while the engine is still

warm to assure rapid and

complete draining.

Figure 3-1: Remove the oil drain plug to drain oil from engine.

Oil Drain

Oil

Drain

Plug

Spark Plug Service

WARNING: DO NOT check for spark

with spark plug removed. DO NOT

crank engine with spark plug removed.

WARNING: If the engine has been run-

ning, the muffler will be very hot. Be

careful not to touch the muffler.

To ensure proper engine operation, the spark plug must

be properly gapped and free of deposits.

Remove the spark plug boot and use a spark plug

wrench to remove the plug, Figure 3-2.

Visually inspect the spark plug. Discard the spark

plug if there is apparent wear, or if the insulator is

cracked or chipped. Clean the spark plug with a wire

brush if it is to be reused.

Measure the plug gap with a feeler gauge. Correct

as necessary by bending side electrode, Figure 3-3.

The gap should be set to 0.02-0.03 inches (0.60-

0.80 mm).

Check that the spark plug washer is in good condi-

tion and thread the spark plug in by hand to prevent

cross-threading.

After the spark plug is seated, tighten with a spark

plug wrench to compress the washer.

NOTE: When installing a new spark plug, tighten

1/2 turn after the spark plug seats to compress the

washer. When reinstalling a used spark plug, tighten

1/8-1/4 turn after the spark plug seats to compress

the washer.

IMPORTANT: The spark plug must be tightened

securely. An loose spark plug can become very hot

and can damage the engine.

Cleaning the Engine

If the engine has been running, allow it to cool for at least

half an hour before cleaning. Periodically remove dirt

build-up from engine.

IMPORTANT: Do not spray engine with water to

clean because water could contaminate fuel. Using

a garden hose or pressure washing equipment can

also force water into the muffler opening. Water that

passes through the muffler can enter the cylinder,

causing damage.

WARNING: Accumulation of debris

around muffler could cause a fire.

Inspect and clean before every use.

Maintaining

the

Engine

WARNING

DO NOT check for spark

with spark plug removed.

DO NOT crank engine

with spark plug removed.

If the engine has been

running, the muffler will

be very hot. Be careful

not to touch the muffler.

Figure 3-2: The spark plug and boot.

Figure 3-3: Use a feeler gauge to measure the plug gap.

Spark Plug

Spark Plug Boot

0.02-0.03 in.

0.60-0.80 mm

Electrode

Storage

Engines stored over 30 days need to be drained of fuel to prevent deterioration and gum from forming in fuel system

or on essential carburetor parts. If the gasoline in your engine deteriorates during storage, you may need to have the

carburetor, and other fuel system components, serviced or replaced.

Remove all fuel from tank by running engine until it stops from lack of fuel.

Change oil. See Oil Change section.

Remove spark plug and pour approximately 1 oz. (30 ml) of clean engine oil into the cylinder. Pull the recoil

starter several times to distribute the oil, and reinstall the spark plug.

Clean debris from around engine, and under, around, and behind muffler. Apply a light film of oil on any areas that

are susceptible to rust.

Store in a clean, dry and well ventilated area away from any appliance that operates with a flame or pilot light,

such as a furnace, water heater, or clothes dryer. Avoid any area with a spark producing electric motor, or where

power tools are operated.

If possible, avoid storage areas with high humidity.

Keep the engine level in storage. Tilting can cause fuel or oil leakage.

Removing From Storage

Check your engine as described in the Pre-Operation Check section in this manual.

If the fuel was drained during storage preparation, fill the tank with fresh gasoline. If you keep a container of

gasoline for refueling, make certain it contains only fresh fuel. Gasoline oxidizes and deteriorates over time,

causing hard starting.

If the cylinder was coated with oil during storage preparation, the engine will smoke briefly at startup. This is

normal.

•

Maintaining

the

Engine

WARNING

Accumulation of debris

around muffler could

cause a fire. Inspect and

clean before every use.

IMPORTANT: Do not

spray engine with water

to clean because water

could contaminate fuel.

Using a garden hose

or pressure washing

equipment can also force

water into the air cleaner

or muffler opening. Water

in the air cleaner will soak

the paper element, and

water that passes through

the element or muffler

can enter the cylinder,

causing damage.

For repairs beyond the

minor adjustments listed

here, contact an autho-

rized service dealer.

Trouble-

shooting

Problem Cause Solution

Engine fails to start Engine flooded from excessive

priming

Spark plug wire disconnected

Fuel tank empty or stale fuel

Engine not choked

Faulty spark plug

Engine not primed

Ignition key installed improperly

Throttle in stop position

Wait at least ten minutes before

starting

Connect wire to spark plug

Fill tank with clean, fresh gasoline

Choke engine

Clean, adjust gap, or replace

Prime engine 3-5 times

Insert ignition key all the way

Move throttle to FAST/RUN position

Engine runs erratically Spark plug wire loose

Spark plug scorched, defective, or

electrode gap set incorrectly

Stale fuel

Unit running with choke on

Water or dirt in fuel system

Connect and tighten spark plug wire

Re-adjust electrode gap or change

spark plug

Fill tank with clean, fresh gasoline

Move choke to off

Drain fuel tank. Refill with fresh fuel.

Engine overheats Engine oil level low1. Fill engine with proper amount of

engine oil.

Troubleshooting

For repairs beyond the minor adjustments listed here, contact an authorized service dealer.

MTD LLC (MTD), The United States Environment Protection Agency (U. S. EPA)

Emission Control System Warranty Statement

(Owner’s Defect Warranty Rights and Obligations)

The U. S. EPA and MTD are pleased to explain the emissions control system warranty on your model year 2005 and later small off-road engine.

New small off-road engines must be designed, built and equipped to meet the stringent anti-smog standards. MTD must warranty the emission

control system on your engine for the period of time listed below, provided there has been no abuse, neglect or improper maintenance of your small

off-road engine.

Your emission control system may include parts such as the carburetor, air cleaner, ignition system, exhaust system, and other associated emis-

sion-related components.

Where a warrantable condition exists, MTD will repair your small off-road engine at no cost to your including diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE:

This emissions control system is warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or

replaced by MTD.

OWNER’S WARRANTY RESPONSIBILITIES:

As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your Owner’s Manual. MTD

recommends that you retain all your receipts covering maintenances on your small off-road engine, but MTD can not deny warranty solely for the

lack of receipts or for your failure to ensure the performance to all scheduled maintenance.

As the small off-road engine owner, you should however be aware that MTD may deny your warranty coverage if your small off-road engine or part

has failed due to abuse, neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your small off-road engine to an Authorized MTD Service Dealer as soon as a problem exists. The warranted

repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact a MTD Service Representative at 1-800-668-1238

and address is MTD Products Ltd., P. O,. Box 1386, 97 Kent Avenue, Kitchener, Ontario Canada N2 G 4J1.

DEFECTS WARRANTY REQUIREMENTS FOR 1995 AND LATER SMALL OFF-ROAD ENGINES:

This section applies to 1995 and later small off-road engines. The warranty period begins on the date the engine or equipment is delivered to an

ultimate purchaser.

(a) General Emissions Warranty Coverage

MTD must warrant to the ultimate purchaser and each subsequent purchaser that the engine is:

(1) Designed, built, and equipped so as to conform with all applicable regulations adopted by the Air Resources Board pursuant to its authority in

Chapters 1 and 2,Part 5, Division 26 of the Health and Safety Code; and

(2) Free from defects in materials and workmanship that cause the failure of a warranted part to be identical in all material respects to the part as

described in the engine manufacturer’s application for certification for a period of two years.

(b) The warranty on emissions-related parts will be interpreted as follows:

(1) Any warranted part that is not scheduled for replacement as required maintenance in the written instructions required by Subsection (c)

must be warranted for the warranty period defined in Subsection (a)(2). If any such part fails during the period of warranty coverage, it must be

repaired or replaced by MTD according to Subsection (4) below. Any such part repaired or replaced under the warranty must be warranted for

the remaining warranty period.

(2) Any warranted part that is scheduled only for regular inspection in the written instructions required by Subsection (c) must be warranted for

the warranty period defined in Subsection (a)(2). A statement in such written instructions to the effect of “repair or replace as necessary” will

not reduce the period of warranty coverage. Any such part repaired or replaced under warranty must be warranted for the remaining warranty

period.

(3) Any warranted part that which is scheduled for replacement as required maintenance in the written instructions required by Subsection (c)

must be warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled

replacement, the part must be repaired or replaced by MTD according to Subsection (4) below. Any such part repaired or replaced under

warranty must be warranted for the remainder of the period prior to the first scheduled replacement point for the part.

(4) Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the owner at a

warranty station.

(5) Notwithstanding the provisions of Subsection (4) above, warranty services or repairs must be provided at all MTD distribution centers that

are franchised to service the subject engines.

(6) The owner must not be charged for diagnostic labor that leads to the determination that a warranted part is in fact defective, provided that

such diagnostic work is performed at a warranty station.

EPA-1-CA

(7) The engine manufacturer is liable for damages to other engine components proximately caused by a failure under warranty of any warranted

part.

(8) Throughout the engine’s warranty period defined in Subsection (a)(2), MTD will maintain a supply of warranted parts sufficient to meet the

expected demand for such parts.

(9) Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to the

owner. Such use will not reduce the warranty obligations of MTD.

(10) Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on or

modified parts shall be grounds for disallowing a warranty claim made in accordance with this article. The engine manufacturer shall not be

liable under this article to warrant failures of warranted parts caused by the use of non-exempted add-on or modified part.

(c) MTD will include a copy of the following emission warranty parts list with each new engine, using those portions of the list applicable to the

engine.

(1) Fuel Metering System

• Cold start enrichment system (soft choke)

• Carburetor and internal parts

• Fuel Pump

(2) Air Induction System

• Air cleaner

• Intake manifold

(3) Ignition System

• Spark plug(s)

• Magneto Ignition System

(4) Exhaust System

(5) Miscellaneous Items Used in Above System

• Vacuum, temperature , position, time sensitive valves and switches

• Connectors and assemblies

EPA-1

notes . . .

(9) Toute pièce de remplacement peut être utilisée pour l’entretien ou la réparation sous garantie et doit être fournie gratuitement au propriétaire. Ceci ne limite pas

les obligations de garantie de MTD.

(10) Les pièces complémentaires ou modifiées qui ne sont pas exemptées par le « Air Resources Board » ne peuvent toutefois pas être utilisées. L’emploi de toute

pièce complémentaire ou modifiée non exemptée sera suffisant pour rejeter une demande d’application de la garantie en vertu de cet article. Le fabricant du

moteur ne sera pas tenu, en vertu de cet article, de garantir les pièces garanties si leur défaillance a été causée par l’utilisation d’une pièce complémentaire ou

modifiée non exemptée.

avec chaque moteur neuf utilisant les parties de la liste qui s’appliquent au moteur.

(1) Système de dosage du carburant

• Système d’enrichissement du carburant pour démarrages à froid

• Carburateur et pièces internes

• Pompe à carburant0

(2) Système d’admission de l’air

• Filtre à air

• Tubulure d’admission

(3) Système d’allumage

• Bougie(s)

• Système d’allumage à magnéto

(4) Système d’échappement

(5) Divers articles utilisés dans le système ci-dessus

• Soupapes de dépression, thermocontacts, soupapes de positionnement et à action minutée et interrupteurs

• Raccords et ensembles

EPA-1-CA

MTD LLC (MTD) et l’Agence de protection de l’environnement des États-Unis (U.S. EPA)

Déclaration de garantie du système antipollution

(Droits et obligations du propriétaire en vertu de la garantie)

C’est avec plaisir que l’U.S. EPA et MTD présentent la garantie du système antipollution du petit moteur hors route fabriqués en 2005 et ultérieurement. Les petits

moteurs hors route neufs doivent être conçus, fabriqués et équipés conformément aux normes antipollution strictes. MTD doit garantir le système antipollution du

moteur pour la durée stipulée ci-dessous, à condition que le petit moteur hors route n’ait pas fait l’objet d’abus, de négligence ou d’un entretien incorrect.

Le système antipollution peut inclure les pièces suivantes : carburateur, filtre à air, système d’allumage, système d’échappement et autres pièces annexes du

système antipollution.

MTD s’engage à effectuer, sans frais pour le propriétaire, les réparations du petit moteur hors route, y compris les diagnostics, les pièces et la main d’œuvre

nécessaires, si la situation est couverte par la garantie.

GARANTIE DU FABRICANT :

Le système antipollution est garanti pour une période de deux ans. Toute pièce annexe du système antipollution du moteur jugée défectueuse sera réparée ou

remplacée par MTD.

RESPONSABILITÉS DU PROPRIÉTAIRE :

Le propriétaire de tout petit moteur hors route est tenu de respecter le calendrier des entretiens requis énoncés dans la notice d’utilisation. MTD recommande de

conserver tous les reçus se rapportant à l’entretien du petit moteur hors route. Toutefois, MTD ne peut pas refuser les réclamations sous garantie uniquement à

cause de l’absence de reçus ou à cause du manquement à effectuer l’entretien requis.

Le propriétaire du petit moteur hors route doit toutefois savoir que MTD peut refuser d’honorer la garantie si le petit moteur hors route ou l’une quelconque de ses

pièces a fait l’objet d’abus, de négligence, d’un entretien incorrect ou de modifications non approuvées.

Le propriétaire est tenu de présenter le petit moteur hors route à une station technique agréée dès l’apparition d’un problème. Les réparations sous garantie

devraient être effectuées dans un délai raisonnable ne dépassant pas 30 jours.

Pour toute question concernant vos droits et responsabilités en vertu de cette garantie, adressez-vous au représentant des services techniques de MTD en

appelant le 1-800-668-1238 ou en écrivant à MTD Products Ltd., P. O. Box 1386, Kitchener, Ontario Canada N2G 4J1.

TERMES DE LA GARANTIE DESc PETITS MOTEURS HORS ROUTE

FABRIQUÉS EN 1995 ET ULTÉRIEUREMENT

Cette section concerne les petits moteurs hors route fabriqués en 1995 et ultérieurement. La période de garantie commence le jour où le moteur ou l’équipement

est livré à l’acheteur au détail initial.

(a) Protection offerte par la garantie du système antipollution

MTD doit garantir à l’acheteur au détail initial et à chaque acheteur successif que le moteur :

(1) a été conçu, construit et équipé conformément à tous les règlements applicables, adoptés par le « Air Resources Board », en vertu de son autorité, et énoncés

dans les Chapitres 1 et 2, Partie 5, Division 26 du Code de la santé et de la sécurité ; et

(2) est exempt de tout vice de matière et de fabrication susceptible de causer la défaillance d’une pièce garantie, en tous points identique à la pièce décrite dans la

demande de certification du fabricant du moteur, pour une période de deux ans.

(b) La garantie des pièces du système antipollution sera interprétée comme suit :

(1) Toute pièce garantie pour laquelle les instructions écrites du paragraphe (c) ne prévoient pas le remplacement dans le calendrier des entretiens requis doit

être garantie pour la période de garantie spécifiée dans le paragraphe (a)(2). Si une telle pièce tombe en panne pendant la période de garantie, elle doit être

réparée ou remplacée par MTD conformément au paragraphe (4) ci-dessous. Toute pièce réparée ou remplacée en vertu de la garantie doit être garantie pour

le solde de la période de garantie.

(2) Toute pièce garantie pour laquelle les instructions écrites du paragraphe (c) prévoient seulement une inspection régulière doit être garantie pour la période de

garantie spécifiée dans le paragraphe (a)(2). La mention dans les instructions écrites de « réparer ou remplacer selon le besoin » ne raccourcit pas la période

de garantie. Toute pièce réparée ou remplacée en vertu de la garantie doit être garantie pour le solde de la période de garantie.

(3) Toute pièce garantie pour laquelle les instructions écrites du paragraphe (c) prévoient le remplacement dans le cadre d’un entretien requis doit être garantie

pour la période précédant le premier remplacement prévu. Si la pièce tombe en panne avant le premier intervalle de remplacement prévu, la pièce doit être

réparée ou remplacée par MTD conformément au paragraphe (4) ci-dessous. Toute pièce réparée ou remplacée sous garantie doit être garantie pour le solde

de la période de garantie avant le premier intervalle de remplacement prévu de la pièce.

(4) La réparation ou le remplacement de toute pièce garantie en vertu de la garantie énoncée dans cet article doit être effectuée par une station technique agréée,

sans frais pour le propriétaire.

(5) Nonobstant les termes du paragraphe (4) ci-dessus, les services ou réparations sous garantie doivent être effectués dans tous les centres de distribution/con-

cessionnaires MTD autorisés à entretenir les moteurs en question.

(6) Les diagnostics permettant d’établir qu’une pièce garantie est défectueuse doivent être effectués sans frais pour le propriétaire, à condition d’être réalisés par

une station technique autorisée à offrir les services sous garantie.

(7) Le fabricant du moteur est tenu responsable des dégâts aux autres pièces du moteur susceptibles d’avoir été causés par la panne sous garantie d’une pièce

garantie.

(8) MTD s’engage à conserver un stock de pièces garanties suffisant pour satisfaire la demande prévue pour ces pièces pendant la période de garantie du moteur

stipulée au paragraphe (a)(2).

EPA-1-CA