Simplicity 120492-0127-E1 Manuel utilisateur

Marque: Simplicity

Modèle: 120492-0127-E1

Catégorie: Accessoires pour véhicules automobiles

Taper: Manuel utilisateur

Document: - page 1 (Black)

Screen angle and frequency: 45.0000, 150.0000

Model Series

Covered in

This Manual

110000

120000

200000

210000

Operating & Maintenance

Instructions

Model Type Code

Month Day

Year

Note: General Model Series numbers noted above are inclusive of the specific model

number found on your engine. To get replacement parts or technical assistance in

the future, write your engine Model, Type, Code and date of purchase here.

TABLE OF CONTENTS

Safety 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engine Information 6. . . . . . . . . . . . . . . . . . . . . . . .

Oil 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel and Starting Information 8. . . . . . . . . . . . . . .

Starting and Stopping 9-10. . . . . . . . . . . . . . . . . . .

Maintenance 11-14. . . . . . . . . . . . . . . . . . . . . . . . .

Parts and Service & Storage 15-16. . . . . . . . . . . .

Warranty Information 17. . . . . . . . . . . . . . . . . . . . .

WARNING

Briggs & Stratton does not approve or authorize the use of

these engines on 3-wheel All Terrain Vehicles (ATVs), motor

bikes, fun/recreational go-karts, aircraft products or vehicles

intended for use in competitive events. Use of these engines in

such applications could result in property damage, serious

injury (including paralysis), or even death.

Need assistance? Go to www.briggsandstratton.com

for detailed information regarding Briggs & Stratton engines.

Or call,

1-800-233-3723, (U.S.A. and Canada)

to hear a menu of pre-recorded messages

offering engine maintenance information.

Not For Reproduction

Document: - page 2 (Black)

Screen angle and frequency: 45.0000, 150.0000

The Power That Works For You)

Look For Relevant Emissions Durability Period and

Air Index Information On Your Engine Emissions Label

Engines that are certified to meet the California Air Resources Board (CARB) Tier 2 Emission Standards must display

information regarding the Emissions Durability Period and the Air Index. Briggs & Stratton makes this information available

to the consumer on our emission labels.

The Emissions Durability Period describes the number of hours of actual running time for which the engine is certified to

be emissions compliant, assuming proper maintenance in accordance with the Operating & Maintenance Instructions. The

following categories are used:

Moderate: Engine is certified to be emission compliant for 125 hours of actual engine running time.

Intermediate: Engine is certified to be emission compliant for 250 hours of actual engine running time.

Extended: Engine is certified to be emission compliant for 500 hours of actual engine running time.

For example, a typical walk-behind lawn mower is used 20 to 25 hours per year. Therefore, the Emissions Durability

Period of an engine with an intermediate rating would equate to 10 to 12 years.

The Air Index is a calculated number describing the relative level of emissions for a specific engine family. The lower the

Air Index, the cleaner the engine. This information is displayed in graphical form on the emissions label.

After July 1, 2000, Look For Emissions Compliance Period On

Engine Emissions Compliance Label

After July 1, 2000 certain Briggs & Stratton engines will be certified to meet the United States Environmental Protection

Agency (USEPA) Phase 2 emission standards. For Phase 2 certified engines, the Emissions Compliance Period referred

to on the Emissions Compliance label indicates the number of operating hours for which the engine has been shown to

meet Federal emission requirements. For engines less than 225 cc displacement, Category C = 125 hours, B = 250 hours

and A = 500 hours. For engines of 225 cc or more, Category C = 250 hours, B = 500 hours and A = 1000 hours.

The displacement of Model Series 110000 engine is 190 cc, Model Series 120000 engine is 206 cc, Model Series 200000

engine is 305 cc, Model Series 210000 engine is 342 cc.

    

    

    

Not For Reproduction

Document: - page 3 (Black)

Screen angle and frequency: 45.0000, 150.0000

BEFORE OPERATING ENGINE

• Read entire Operating & Maintenance Instructions AND

the instructions for the equipment this engine powers.*

• Failure to follow instructions could result in serious injury

or death.

THE OPERATING & MAINTENANCE INSTRUCTIONS

CONTAIN SAFETY INFORMATION TO

• Make you aware of hazards associated with engines

• Inform you of the risk of injury associated with those hazards, and

• Tell you how to avoid or reduce the risk of injury.

275092

The safety alert symbol ( ) is used to identify safety

information about hazards that can result in personal injury.

A signal word (DANGER, WARNING, or CAUTION) is

used with the alert symbol to indicate the likelihood and the

potential severity of injury. In addition, a hazard symbol

may be used to represent the type of hazard.

DANGER indicates a hazard which, if not

avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not

avoided, might result in minor or moderate

injury.

CAUTION, when used without the alert symbol,

indicates a situation that could result in damage

to the engine.

WARNING

The engine exhaust from this prod-

uct contains chemicals known to the

State of California to cause cancer,

birth defects, or other reproductive

harm.

HAZARD SYMBOLS AND MEANINGS

Explosion

Toxic Fumes

Moving Parts

ShockHot Surface

Kickback

Fire

THE INTERNATIONAL SYMBOLS USED

ON THE ENGINE OR

IN THIS MANUAL INCLUDE:

On Off

Fuel Shutoff

Read Owner’s

Manual

Stop Fuel

Choke

Safety Alert

Oil

* Briggs & Stratton does not necessarily know what equipment this engine will power. For that reason, you should carefully read

and understand the operating instructions for the equipment on which your engine is placed.

Not For Reproduction

Document: - page 4 (Black)

Screen angle and frequency: 45.0000, 150.0000

SAFETY

Gasoline and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WARNING

WHEN ADDING FUEL

• Turn engine OFF and let engine cool at least 2

minutes before removing gas cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. Fill tank to approximately

1-1/2 inches below top of neck to allow for fuel

expansion.

• Keep gasoline away from sparks, open flames,

pilot lights, heat, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently

for cracks or leaks. Replace if necessary.

WHEN STARTING ENGINE

• Make sure spark plug, muffler, fuel cap and air

cleaner are in place.

• Do not crank engine with spark plug removed.

• If fuel spills, wait until it evaporates before starting

engine.

• If engine floods, set choke to OPEN/RUN position,

place throttle in FAST and crank until engine starts.

WHEN OPERATING EQUIPMENT

• Do not tip engine or equipment at angle which

causes gasoline to spill.

• Do not choke carburetor to stop engine.

WHEN TRANSPORTING EQUIPMENT

• Transport with fuel tank EMPTY or with fuel shut-off

valve OFF.

WHEN STORING GASOLINE OR EQUIPMENT

WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters or

other appliances that have pilot light or other

ignition source because they can ignite gasoline

vapors.

Starting engine creates sparking.

Sparking can ignite nearby flammable

gases.

Explosion and fire could result.

WARNING

• If there is natural or LP gas leakage in area, do not

start engine.

• Do not use pressurized starting fluids because

vapors are flammable.

WARNING

Rapid retraction of starter cord (kickback) will

pull hand and arm toward engine faster than

you can let go.

Broken bones, fractures, bruises or sprains

could result.

• When starting engine, pull cord slowly until

resistance is felt, then pull rapidly.

• Remove all external equipment/engine loads

before starting engine.

• Direct coupled equipment components such as,

but not limited to, blades, impellors, pulleys,

sprockets, etc., must be securely attached.

WARNING

Rotating parts can contact or entangle

hands, feet, hair, clothing, or accessories.

Traumatic amputation or severe laceration

can result.

• Operate equipment with guards in place.

• Keep hands and feet away from rotating parts.

• Tie up long hair and remove jewelry.

• Do not wear loose-fitting clothing, dangling

drawstrings or items that could become caught.

Not For Reproduction

Document: - page 5 (Black)

Screen angle and frequency: 45.0000, 150.0000

SAFETY

Engines give off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide can cause

nausea, fainting or death.

WARNING

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if

doors or windows are open.

WARNING

Running engines produce heat. Engine

parts, especially muffler, become extremely

hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass,

brush, etc. can catch fire.

• Allow muffler, engine cylinder and fins to cool

before touching.

• Remove accumulated combustibles from muffler

area and cylinder area.

• Install and maintain in working order a spark

arrester before using equipment on forest-covered,

grass-covered, brush-covered unimproved land.

The state of California requires this (Section 4442

of the California Public Resources Code). Other

states may have similar laws. Federal laws apply

on federal land.

WARNING

Unintentional sparking can result in fire or

electric shock.

Unintentional start-up can result in en-

tanglement, traumatic amputation, or lac-

eration.

BEFORE PERFORMING ADJUSTMENTS OR

REPAIRS

• Disconnect spark plug wire and keep it away from

spark plug.

• Disconnect battery at negative terminal (only

engines with electric start).

WHEN TESTING FOR SPARK

• Use approved spark plug tester.

• Do not check for spark with spark plug removed.

ENGINE INFORMATION

TECHNICAL INFORMATION

POWER RATINGS: The power ratings for an individual engine

model are initially developed by starting with SAE (Society of Auto-

motive Engineers) code J1940 (Small Engine Power & Torque

Rating Procedure) (Revision 2002-05). Given both the wide array

of products on which our engines are placed, and the variety of en-

vironmental issues applicable to operating the equipment, it may

be that the engine you have purchased will not develop the rated

horsepower when used in a piece of power equipment (actual “on-

site” power). This difference is due to a variety of factors including,

but not limited to, the following: differences in altitude, tempera-

ture, barometric pressure, humidity, fuel, engine lubrication, maxi-

mum governed engine speed, individual engine to engine variabil-

ity, design of the particular piece of power equipment, the manner

in which the engine is operated, engine run-in to reduce friction

and clean out of combustion chambers, adjustments to the valves

and carburetor, and other factors. The power ratings may also be

adjusted based on comparisons to other similar engines utilized

in similar applications, and will therefore not necessarily match the

values derived using the foregoing codes.

Not For Reproduction

Document: - page 6 (Black)

Screen angle and frequency: 45.0000, 150.0000

ENGINE INFORMATION

1. Spark plug

2. Air cleaner

3. Choke

4. Carburetor

5. Fuel shut-off valve

(if equipped)

6. Rope handle

7. Finger guard

8. Stop switch/OIL GARD® light

(if equipped)

9. Fuel fill

10. Fuel tank

11. Oil fill/Dipstick

(if equipped)

12. Blower housing

13. Oil drain plug

14. Oil fill cap

15. Engine Model Type Code

xxxxx xxxx xx xxxxxxxx

16. Muffler/(Muffler guard, if equipped)/

(Spark arrester, if equipped)

GENERAL INFORMATION

ENGINE MODEL

This is a single cylinder, overhead valve (OHV), air-cooled

engine. It is a low emissions engine.

In the state of California, OHV Model Series 110000 and

120000 engines are certified by the California Air Re-

sources Board to meet emissions standards for 125 hours.

OHV Model Series 200000, 210000 engines are certified

by the California Air Resources Board to meet emissions

standards for 250 hours. Such certification does not grant

the purchaser, owner or operator of this engine any

additional warranties with respect to the performance or

operational life of this engine. This engine is warranted

solely according to the product and emissions warranties

stated elsewhere in this manual.

Note: For practical operation, horsepower loading should

not exceed 85% of rated horsepower. Engine power will de-

crease 3-1/2% for each 1,000 feet (300 meters) above sea

level and 1% for each 10° F (5.6° C) above 77° F (25° C).

Engine will operate satisfactorily at an angle up to 15°.

MODEL SERIES 110000

Bore 2-11/16 in. (68 mm). . . . . . . . . . . . . . . . . . . . . . . . . . .

Stroke 2-3/64 in. (52 mm). . . . . . . . . . . . . . . . . . . . . . . . . .

Displacement 11.58 cu. in. (190 cc). . . . . . . . . . . . . . . . . .

MODEL SERIES 120000

Bore 2-11/16 in. (68 mm). . . . . . . . . . . . . . . . . . . . . . . . . . .

Stroke 2-13/64 in. (56 mm). . . . . . . . . . . . . . . . . . . . . . . . .

Displacement 12.48 cu. in. (206 cc). . . . . . . . . . . . . . . . . .

MODEL SERIES 200000

Bore 3.120 in. (79.23 mm). . . . . . . . . . . . . . . . . . . . . . . . . .

Stroke 2.438 in. (61.67 mm). . . . . . . . . . . . . . . . . . . . . . . .

Displacement 18.64 cu. in. (305 cc). . . . . . . . . . . . . . . . . .

MODEL SERIES 210000

Bore 3.300 in. (83.81 mm). . . . . . . . . . . . . . . . . . . . . . . . . .

Stroke 2.438 in. (61.67 mm). . . . . . . . . . . . . . . . . . . . . . . .

Displacement 20.85 cu. in. (342 cc). . . . . . . . . . . . . . . . . .

TUNE-UP SPECIFICATIONS

Models 110000/120000

Armature air gap 0.010 – 0.014 in. (0.25 – 0.36 mm). . .

Spark plug gap 0.030 in. (0.76 mm). . . . . . . . . . . . . . . . . .

Valve clearance with valve springs installed and piston 1/4 in.

(6 mm) past top dead center (check when engine is cold).

See Repair Manual P/N 272147.

Intake 0.004 – 0.006 in. (0.10 – 0.15 mm). . . . . . . . . . . . .

Exhaust 0.009 – 0.011 in. (0.23 – 0.28 mm). . . . . . . . . . .

TUNE-UP SPECIFICATIONS

Models 200000/210000

Armature air gap 0.008 – 0.012 in. (0.20 – 0.30 mm). . .

Spark plug gap 0.030 in. (0.76 mm). . . . . . . . . . . . . . . . . .

Valve clearance with valve springs installed and piston 1/4 in.

(6 mm) past top dead center (check when engine is cold).

See Repair Manual P/N 272147.

Intake 0.004 – 0.006 in. (0.10 – 0.15 mm). . . . . . . . . . . . .

Exhaust 0.004 – 0.006 in. (0.10 – 0.15 mm). . . . . . . . . . .

Not For Reproduction

Document: - page 7 (Black)

Screen angle and frequency: 45.0000, 150.0000

OIL

275092

CAUTION: This engine is shipped from Briggs &

Stratton without oil

. Check oil level before starting

engine. If you start the engine without oil, the

engine will be damaged beyond repair and will not

be covered under warranty.

Note: If this engine is equipped with gear reduction, gear

reduction case must be filled with oil prior to operating en-

gine. See gear reduction oil filling instructions on page 12.

OIL CAPACITY

Model 110000 and 120000 series engines hold approxi-

mately 5/8 quart (20 ounces; 0.6 liter).

Model series 200000 and 210000 engines hold approxi-

mately 7/8 quart (28 ounces; 0.8 liter).

TYPE OF OIL TO USE

• Use a high quality detergent oil classified “For Service

SF, SG, SH, SJ” or higher, such as Briggs & Stratton

SAE 30, Part Number 100005 (20 oz) or 100028 (48 oz).

• Do not use special additives.

• Choose a viscosity according to the table opposite.

Note: Synthetic oil meeting ILSAC GF-2, API

certification mark and API service symbol

(shown at left) with “SJ/CF ENERGY CON-

SERVING” or higher, is an acceptable oil at all

temperatures. Use of synthetic oil does not

alter required oil change intervals.

°F

-20 0 20 40 60 80 100

°C

-30 -20 -10 0 10 20 30 40

STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

* CAUTION: Air cooled engines run hotter than automotive

engines. The use of non-synthetic multi-viscosity oils

(5W-30, 10W-30, etc.) in temperatures above 40° F (4° C)

will result in higher than normal oil consumption. When using

a multi-viscosity oil, check oil level more frequently.

** CAUTION: SAE 30 oil, if used below 40° F (4° C), will result

in hard starting and possible engine bore damage due to

inadequate lubrication.

SAE Viscosity Grades

CHECKING AND ADDING OIL

• Check oil level before starting the engine.

• Check level daily, or after every eight (8) hours.

• Keep oil level at FULL.

• Do not overfill.

[1] Place engine level and

clean around oil fill area.

[2] Remove dipstick and wipe with clean

cloth. Replace and tighten dipstick.

Remove and check oil level.

High

Oil Fill

(if equipped)

FULL

[3] Pour oil slowly. Fill to FULL line on

dipstick – recheck.

[4] Replace and tighten dipstick.

[1] Place engine level and

clean around oil fill area.

[2] Remove oil fill

cap or dipstick.

Low

Oil Fill

OIL LEVEL

[3] Pour oil slowly. Fill to

point of overflowing.

[4] Replace and tighten

oil fill cap.

Not For Reproduction

Document: - page 8 (Black)

Screen angle and frequency: 45.0000, 150.0000

OIL

CHECKING AND ADDING OIL

[1] Remove dipstick

and wipe with

clean cloth.

Low

Oil Fill

with Dipstick

[2] Insert dipstick,

but DO NOT

TIGHTEN.

Remove and

check oil level.

[3] Pour oil slowly.

Fill to FULL

mark on dip-

stick. Replace

and tighten dip-

stick.

FULL OIL

LEVEL

FUEL

TYPE OF FUEL TO USE

• Use clean, fresh, regular unleaded gasoline with a

minimum of 85 octane. Fresh fuel prevents gum from

forming in the fuel system or on essential carburetor parts.

Purchase fuel in quantity that can be used within 30 days.

• Do not use gasoline which contains Methanol.

• Do not mix oil with gasoline.

• For engine protection use Briggs & Stratton Gasoline

Additive available from your Authorized Briggs &

Stratton Dealer (P/N 5041 or single use pouch).

• This engine is certified to operate on gasoline. Exhaust

Emission Control System: EM (Engine Modifications).

CAUTION: Some fuels, called oxygenated or reformu-

lated gasoline, are gasoline blended with alcohols or

ethers. Excessive amounts of these blends can damage

the fuel system or cause performance problems. If any

undesirable operating symptoms occur, use gasoline

with a lower percentage of alcohol or ether.

ADDING FUEL

Fuel Fill

WARNING

[1] Remove cap. Fill tank to approximately 1-1/2

inches below top of neck to allow for fuel

expansion. Be careful not to overfill.

Briggs & Stratton Smart-fill) fuel can fills to the

correct level and automatically shuts off, reduc-

ing spills and emissions.

[2] Replace cap before starting.

• Turn engine OFF and let engine cool at least 2

minutes before removing gas cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Keep gasoline away from sparks, open flames,

pilot lights, heat, and other ignition sources.

• If fuel spills, wait until it evaporates before

starting engine.

STARTING

STARTING AND OPERATING TIPS

♦ Store and fuel equipment in level position.

♦ Use fresh fuel. (See Fuel.)

♦ Use correct type of oil for expected starting

temperature. (See Oil.)

♦ Remove external equipment/engine loads. (See

equipment operating instructions.)

♦ Periodically remove any debris buildup from the

machine (See Maintenance.)

♦ After engine has started, let it warm up several

seconds to several minutes, depending on outside

temperature.

♦ For maximum performance and life, operate engine

with choke in RUN and throttle in FAST.

Not For Reproduction

Document: - page 9 (Black)

Screen angle and frequency: 45.0000, 150.0000

STARTING AND STOPPING

WARNING

• Do not use pressurized starting fluids.

• Vapors are flammable.

CAUTION: Some engines may be equipped with OIL

GARD®. The OIL GARD® is intended to warn the

operator that the engine is low on oil. Always check oil

level before starting. Engine damage may occur if the oil

level is not properly maintained and will void warranty

coverage. If the engine will not start, has stopped running

and/or a light flickers in the stop switch, add oil (see

instructions).

REWIND (MANUAL) STARTER

TO START ENGINE

[1] Check oil level (see p. 7).

[2] Turn fuel shut-off valve (if equipped) 1/4 turn

to OPEN.

[3] Push choke lever to CHOKE position.

[4] Move throttle (if

equipped) to FAST.

Operate engine with

throttle in FAST.

Fuel shut-off Choke

OIL

LEVEL

FULL

OPEN

POSITION

[5] Push rocker switch

(if equipped) to ON.

[6] Grasp rope handle. Pull slowly until

resistance is felt, then pull rapidly to start

engine and avoid kickback.

[7] Let engine warm up.

If choke equipped:

Slowly adjust toward RUN

position. Wait until engine

runs smoothly before

each choke adjustment.

WARNING

TO STOP ENGINE

[1] Move throttle (if equipped)

to SLOW, then to STOP.

Fuel shut-off

[2] Push rocker switch

(if equipped) to

OFF.

[3] Close fuel shut-off

valve (if equipped).

CAUTION: Do not stop

engine by moving choke

control to CHOKE.

Backfire, fire or engine

damage could occur.

Not For Reproduction

Document: - page 10 (Black)

Screen angle and frequency: 45.0000, 150.0000

STARTING AND STOPPING

ELECTRIC (KEY) STARTER (if equipped)

TO START ENGINE

[1] Check oil level (see p. 7).

[2] Turn fuel shut-off valve (if equipped) 1/4 turn

to OPEN.

[3] Push choke lever to CHOKE position.

[4] Move throttle

(if equipped) to FAST.

Operate engine with

throttle in FAST.

Fuel shut-off Choke

OPEN

POSITION

OIL

LEVEL

FULL

[5] Push rocker switch (if

equipped) to ON.

[6] Insert key and

turn to START.

CAUTION: To prolong starter life, use short starting

cycles (5 seconds maximum, then wait one minute).

Follow equipment manufacturer’s recommendations

for charging battery.

[7] Let engine warm up.

If choke equipped: Slowly adjust toward RUN

position. Wait until engine runs smoothly before

each choke adjustment.

TO STOP ENGINE

[1] Move throttle

(if equipped) to SLOW.

[2] Turn key to OFF. Remove key

and store out of reach of children.

Fuel shut-off[3] Push rocker switch

(if equipped) to OFF.

[4] Close fuel shut-off valve

(if equipped).

Not For Reproduction

Document: - page 11 (Black)

Screen angle and frequency: 45.0000, 150.0000

MAINTENANCE

Regular maintenance will improve the performance and

extend the life of the engine. See any Authorized Briggs &

Stratton Dealer for service. Use only genuine Briggs &

Stratton parts. Other parts may not perform as well,

may damage the engine, and may result in injury. In

addition, use of other parts may void your warranty.

EMISSION CONTROL

Maintenance, replacement or repair of the emission

control devices and systems may be performed by any

nonroad engine repair establishment or individual.

However, to obtain no charge repairs under the terms and

provisions of the Briggs & Stratton warranty statement, any

service or emission control part repair or replacement must

be performed by a factory authorized dealer.

Task

Perform task at hourly

or calendar interval,

whichever comes first.

Every 8 Hours

or Daily

25 Hours or

Every Season

50 Hours or

Every Season

100 Hours or

Every Season

Yearly

Check Oil Level

Clean Debris

Change Oil

Change oil in gear re-

duction (if equipped)

Service air cleaner

pre-cleaner (if e-

quipped)

4**

Service air cleaner car-

tridge (if not equipped

with pre-cleaner)

4**

Service air cleaner car-

tridge (if equipped with

pre-cleaner)

4**

Inspect spark arrester

(if equipped)

Replace spark plug

Replace fuel filter

(if equipped)

Clean cooling system

4**

Check valve clearance

* Change oil after first 5 to 8 hours of use, then every

50 hours or every season. Change oil every 25 hours

when operating the engine under heavy load or in high

temperatures.

** Clean more often under dusty conditions or when

airborne debris is present. Replace air cleaner parts, if

very dirty.

CAUTION: Used oil is a hazardous waste product.

Dispose of used oil properly. Do not discard with

household waste. Check with your local authorities,

service center, or dealer for safe disposal/recycling

facilities.

CHANGING OIL

[1] Place engine level.

[2] Disconnect spark plug

wire and keep it away

from spark plug. Discon-

nect battery (if equipped

with electric starter) at

negative terminal.

[3] With engine OFF but still warm remove oil drain

plug and drain oil into appropriate receptacle.

[4] Reinstall drain plug. Remove dipstick (if

equipped) or oil fill cap.

[5] Add new oil, about 7/8 quart (28 ounces: 0.8 liter).

Fill to FULL line on dipstick or to point of

overflowing at oil fill cap. Do not overfill.

[6] Replace dipstick or oil fill cap.

Typical

drain plugs

5/16” HEX

PIPE

OIL LEVEL

OIL DRAIN PLUG

3/8” SQUARE

High Oil Fill

(if equipped)

Low Oil Fill

WARNING

Not For Reproduction

Document: - page 12 (Black)

Screen angle and frequency: 45.0000, 150.0000

MAINTENANCE

AIR CLEANER

All engines have an air cleaner cartridge. The cartridge is

either flat or oval (see illustrations). In addition, some

engines have a pre-cleaner.

Pre-cleaner

To clean pre-cleaner (if equipped), separate it from

cartridge and wash in liquid detergent and water. Air dry

thoroughly. Do not oil pre-cleaner. Re-assemble dry

pre-cleaner on clean cartridge.

CAUTION: Do not use pressurized air or solvents to

clean cartridge. Pressurized air can damage

cartridge; solvents will dissolve cartridge.

REMOVING and INSTALLING FLAT AIR CLEANER

[1] Loosen screw, tilt cover down and remove air cleaner.

[2] Install clean (or new) air cleaner assembly inside

cover. If equipped with pre-cleaner, install with arrows

up and lip of pre-cleaner at bottom of cartridge pleats.

[3] Insert cover’s tabs into slots in bottom of base.

[4] Tilt cover up into place and tighten screw.

FLAT AIR CLEANER

COVER

PRE-CLEANER

P/N 493537

CARTRIDGE

P/N 491588

BASE

SLOTS AND

TABS

SCREW

REMOVING and INSTALLING OVAL AIR CLEANER

[1] Remove knob and cover.

[2] Lift air cleaner assembly (pre-cleaner, if equipped,

and cartridge) off stud.

[3] Push clean (or new) air cleaner assembly in base firmly

down on stud. Air cleaner must fit securely in base.

[4] Push cover squarely onto base.

[5] Tighten knob.

ASSEMBLE SO CARTRIDGE LIP SITS INSIDE BASE

COVER

PRE-CLEANER

P/N 273356

STUD

CARTRIDGE

P/N 690610

BASE

KNOB

OVAL AIR CLEANER

MODEL SERIES

110000 / 120000

OVAL AIR CLEANER

MODEL SERIES

200000 / 210000

PRE-CLEANER

P/N 695303

CARTRIDGE

P/N 695302

CHANGING OIL IN GEAR REDUCTION

(if equipped)

Change oil in gear reduction after every 100 hours.

[1] To drain oil, loosen 4 gear case cover screws and drain

oil into appropriate receptacle.

[2] After draining, torque 4 screws to 85 in-lbs.

[3] To refill, pour SAE 30 oil into oil fill hole until it runs out

level check hole.

[4] Replace both oil plugs.

Note: Oil filler plug has a vent hole and must be installed on

top of gear case cover.

OIL FILLER PLUG

OIL LEVEL

PLUG

VENT HOLE

4 GEAR CASE

COVER SCREWS

Not For Reproduction

Document: - page 13 (Black)

Screen angle and frequency: 45.0000, 150.0000

MAINTENANCE

ENGINE AND ENGINE PARTS

We recommend that you see an authorized Briggs & Stratton Service Dealer for all maintenance and service of the engine

and engine parts. Use only genuine Briggs & Stratton parts.

WARNING

If you perform any maintenance on the engine, first disconnect the spark plug wire

from the spark plug, and disconnect the battery at the negative terminal (electric

starter engines only) to prevent unintentional sparking. Unintentional sparking can

result in fire or electric shock. Unintentional start-up can result in entanglement,

traumatic amputation or laceration. Use only correct tools.

WARNING

• Do not strike the flywheel with a hammer or hard object because the flywheel may

later shatter during operation.

• Do not tamper with governor spring, links or other parts to increase engine speed.

MUFFLER

Replacement parts for the muffler

must be the same and installed in the

same position as the original parts,

otherwise fire can occur.

If muffler is equipped with spark arrester screen, remove scree

for inspection. Replace screen if damaged or plugged.

WARNING

SPARK PLUG

Use only Briggs & Stratton Spark Tester (part number

19368) to check for spark.

Note: In some areas, local law requires using resistor spark

plug to suppress ignition signals. If this engine was

originally equipped with resistor spark plug, use same type

for replacement.

.030” (0.76 mm)

WIRE GAGE

RESISTOR P/N 491055

FUEL SYSTEM

Replacement parts for fuel system

(cap, hoses, tanks, filters, etc.)

must be the same as original parts,

otherwise fire can occur.

WARNING

REPLACE FUEL FILTER (if equipped)

Drain fuel tank or close fuel shut-off valve before replacing

fuel filter. Otherwise, fuel can leak out, creating a

fire/explosion hazard.

FUEL FILTER

P/N 499638

FUEL HOSE

CLAMPS

Not For Reproduction

Document: - page 14 (Black)

Screen angle and frequency: 45.0000, 150.0000

MAINTENANCE

CLEANING DEBRIS

CAUTION: Do not use water to clean engine parts.

Water could contaminate fuel system. Use a brush

or dry cloth.

Daily or before every use, clean accumulated debris from

engine. Keep linkage, spring and controls clean. Keep area

around and behind muffler free of any combustible debris.

Engine parts should be kept clean to

reduce the risk of overheating and

ignition of accumulated debris.

WARNING

Finger Guard,

Linkage, Springs,

Controls,

Muffler and

Spark Arrester

CLEAN

SPARK

ARRESTER

(IF EQUIPPED)

AIR COOLING SYSTEM

Over time debris may accumulate in cylinder cooling fins

and cannot be observed without partial engine disassem-

bly. For this reason, we recommend that you have an

authorized Briggs & Stratton Service Dealer clean the air

cooling system per recommended intervals. (See Mainte-

nance Schedule on page 12.) Equally important is to keep

top of engine free from debris. See cleaning debris below.

CLEAN

Not For Reproduction

Document: - page 15 (Black)

Screen angle and frequency: 45.0000, 150.0000

SERVICE & STORAGE

PARTIAL LIST OF GENUINE BRIGGS &

STRATTON PARTS

BRIGGS & STRATTON

PART

PART NUMBER

Flat air cleaner cartridge 491588 -OR- 5043

Flat air cleaner pre-cleaner 493537 -OR- 5064

Model Series 110000 / 120000

Oval air cleaner cartridge 690610 -OR- 5059

Oval pre-cleaner 273356 -

OR- 5059

Model Series 200000 / 210000

Oval air cleaner cartridge 695302

Oval pre-cleaner 695303

Oil foam air cleaner pre-cleaner 273332

Oil 100005 -

OR- 100028

Fuel filter 694485

Gas additive 5041

Resistor spark plug 491055

Long life platinum spark plug 5066

(used on most OHV engines)

Spark plug wrench 89838 -OR- 5023

Spark tester 19368

Oil pump kit 5056

(uses standard electric drill to remove oil from engine quickly)

SERVICE

See an Authorized Briggs & Stratton Service Dealer. Each

one carries a stock of Genuine Briggs & Stratton Parts and

is equipped with special service tools. Trained mechanics

assure expert repair service on all Briggs & Stratton

engines. Only dealers advertising as “Authorized Briggs &

Stratton” are required to meet Briggs & Stratton standards.

When you purchase equipment powered by a

Briggs & Stratton engine, you are assured of

highly skilled, reliable service at more than

30,000 Authorized Service Dealers

worldwide, including more than 6,000 Master

Service Technicians. Look for these signs

wherever Briggs & Stratton service is offered.

You may locate your nearest Authorized Briggs & Stratton

Service Dealer in our dealer locator map on our web site

 or in the “Yellow Pages™”

directory under “Engines, Gasoline” or “Gasoline

Engines,” or “Lawn Mowers” or similar category.

Note: Walking fingers logo and “Yellow Pages” are regis-

tered trademarks in various jurisdictions.

™

An illustrated shop manual includes com-

mon specifications and detailed informa-

tion covering adjustment, tune-up and

repair of Briggs & Stratton single cylinder,

OHV, 4 cycle engines. It is available for

purchase from an Authorized Briggs &

Stratton Service Dealer or you can order it

from the factory. Write:

Briggs & Stratton Corporation

Attn: Service Division

P. O. Box 1144

Milwaukee, WI 53201

Part No. 272147

Not For Reproduction

Document: - page 16 (Black)

Screen angle and frequency: 45.0000, 150.0000

SERVICE & STORAGE

STORAGE

Engines stored over 30 days need special attention.

[1] To prevent gum from forming in fuel system or on

essential carburetor parts:

a) if fuel tank contains oxygenated or reformulated

gasoline (gasoline blended with an alcohol or an

ether), run engine until it stops from lack of fuel, or b) if

fuel tank contains gasoline, either run engine until it

stops from lack of fuel, or add a gasoline additive to the

gas in the tank. (See parts list. Single – use pouches of

gas additive are available from your service dealer.) If

you use a gas additive, run the engine for several

minutes to circulate the additive through the carburetor.

Then, engine and fuel can be stored up to 24 months.

[2] While engine is still warm, change oil.

[3] Remove spark plug and pour about 1 oz. (30 ml) of

engine oil into cylinder. Replace spark plug and crank

slowly to distribute oil.

[4] Clean engine of surface debris, chaff or grass.

WARNING

[5] Store in a clean, dry area. Do

not store in same area as a

stove, furnace, water heater,

or other appliance that uses a

pilot light or has a device that

can create a spark.

Not For Reproduction

Document: - page 1 (Black)

Screen angle and frequency: 45.0000, 150.0000

               

      

LIMITED WARRANTY

Briggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the engine that is defective in material or workmanship or both.

Transportation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for the

time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map

at www.briggsandstratton.com

, or by calling 1-800-233-3723, or as listed in the ‘Yellow Pages™’.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED

WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT

EXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or

countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state and country to country.





r

 



(Sleeve Bore)

!"



(Kool Bore)

!#  $

%&r

%!

%45

'

"

Commercial Use

2 years

90 days

1 year

Consumer Use

2 years

90 days

1 year

( 

 )*



1 year

* Note the following special warranty periods: 2 years for Classic™ engines in the European Union and Eastern European countries, for all consumer

products in the European Union, and for emission control systems on engines certified by EPA and CARB. 5 years for Consumer use, 90 days for

Commercial use of Touch-N-Mow® starter on Quantum® and Intek™ engines. One year for Consumer use, 90 days for Commercial use on engines

certified to operate on Kerosene fuel. Engines used on Home Standby Generator applications are warranted under Consumer use only. This warranty

does not apply to engines on equipment used for prime power in place of a utility. Engines used in competitive racing or on commercial or rental

tracks are not warrantied.

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the table above. “Consumer use”

means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once an

engine has experienced commercial use, it shall thereafter be considered as a commercial use engine for purposes of this warranty.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE

RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE

MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

        

       

       

      

     ! "  

         #

      

  

      

          

   

$           

        

 #         

    !  

 $    

!      %    

        & 

      

           

      



 

' #      

      (  

      "      

 

 

&          

         

          

          

 

        #

         

        

 



!"   #   

$ %" 

     

 " &  "" " #   

  "  '   & 



) *+,-' ./' 0 *+& &1& +' 2,&

,+$3$2- +$33  &+&&,2 *+&

4 '      

     

  5.  6

7

-#     # 

        

 5/   8    

 !  * 2 9:;)6

; *     #   

     

        

5#       <=  

+      

6 ,$- 3+®     

 '        

  + ,  

$

9

+  %     

      

       

>

         

      

 8     8 

    5 

   8  ,8!®

  

 8    6 +

,   $

? *   8  

          

        

        

 5.       

   6 + , 

 $

<

'    #  "

       

      

    

   # 8  

  

@    # #   #  

%         

 

" 8 

): + 8  %   

)) '      

       

        

       

 



     "#"  

"" "  "(  )## * +

, -  ."( + / 

  " 0-  1#™2   " 

 0# 32  03 #2 04

52   # 

( (  

Not For Reproduction

Document: - page 2 (Black)

Screen angle and frequency: 45.0000, 150.0000

  ! !'!! +,- . /!  !" ! +,

 . (  0!& !"! "1 +(22 ,

&! !! 1& 1 & +#3 )/" 1 .  4!,

The California Air Resources Board (CARB), U.S.

EPA and B&S are pleased to explain the Emis-

sions Control System Warranty on your small off-

road engine (SORE). In California, new small off-

road engines model year 2006 and later must be

designed, built and equipped to meet the State’s

stringent anti-smog standards.

Elsewhere in the United States, new non-road,

spark-ignition engines certified for model year

1997 and later must meet similar standards set

forth by the U.S. EPA. B&S must warrant the emis-

sions control system on your engine for the peri-

ods of time listed below, provided there has been

no abuse, neglect or improper maintenance of

your small off-road engine.

Your emissions control system includes parts

such as the carburetor, air cleaner, ignition sys-

tem, fuel line, muffler and catalytic converter.

Also included may be connectors and other

emissions related assemblies.

Where a warrantable condition exists, B&S will

repair your small off-road engine at no cost to

you including diagnosis, parts and labor.

  ! &! !! )/" 1 !0

Small off-road engines are warranted relative to emissions control parts defects for a period of two years, subject to provisions set forth below. If any

covered part on your engine is defective, the part will be repaired or replaced by B&S.

#3 1 '!4

As the small off-road engine owner, you are re-

sponsible for the performance of the required

maintenance listed in your Operating and Main-

tenance Instructions. B&S recommends that

you retain all your receipts covering mainte-

nance on your small off-road engine, but B&S

cannot deny warranty solely for the lack of re-

ceipts or for your failure to ensure the perfor-

mance of all scheduled maintenance.

As the small off-road engine owner, you should

however be aware that B&S may deny you war-

ranty coverage if your small off-road engine or a

part has failed due to abuse, neglect, improper

maintenance or unapproved modifications.

You are responsible for presenting your small

off-road engine to an Authorized B&S Service

Dealer as soon as a problem exists.

The undisputed warranty repairs should be

completed in a reasonable amount of time, not

to exceed 30 days.

If you have any questions regarding your war-

ranty rights and responsibilities, you should con-

tact a B&S Service Representative at

1-414-259-5262.

The emissions warranty is a defects warranty.

Defects are judged on normal engine perfor-

mance. The warranty is not related to an in-use

emissions test.

  ! &! !! )/" 1 !0!

The following are specific provisions relative to your emissions Control Defects Warranty Coverage. It is in addition to the B&S engine warranty for

non-regulated engines found in the Operating and Maintenance Instructions.

1. Warranted Parts

Coverage under this warranty extends only

to the parts listed below (the emissions con-

trol systems parts) to the extent these parts

were present on the engine purchased.

a. Fuel Metering System

• Cold start enrichment system

• Carburetor and internal parts

• Fuel Pump

• Fuel line, fuel line fittings, clamps

b. Air Induction System

• Air cleaner

• Intake manifold

c. Ignition System

• Spark plug(s)

• Magneto ignition system

d. Catalyst System

• Catalytic converter

• Exhaust manifold

• Air injection system, Pulse valve

e. Miscellaneous Items

• Vacuum, temperature, position,

time sensitive valves

and switches

• Connectors and assemblies

2. Length of Coverage

B&S warrants to the initial owner and each

subsequent purchaser that the Warranted

Parts shall be free from defects in materials

and workmanship which caused the failure

of the Warranted Parts for a period of two

years from the date the engine is delivered to

a retail purchaser.

3. No Charge

Repair or replacement of any Warranted

Part will be performed at no charge to the

owner, including diagnostic labor which

leads to the determination that a Warranted

Part is defective, if the diagnostic work is

performed at an Authorized B&S Service

Dealer. For emissions warranty service

contact your nearest Authorized B&S Ser-

vice Dealer as listed in the “Yellow Pages”

under “Engines, Gasoline,” “Gasoline En-

gines,” “Lawn Mowers,” or similar category.

4. Claims and Coverage Exclusions

Warranty claims shall be filed in accordance

with the provisions of the B&S Engine War-

ranty Policy. Warranty coverage shall be ex-

cluded for failures of Warranted Parts which

are not original B&S parts or because of

abuse, neglect or improper maintenance as

set forth in the B&S Engine Warranty Policy.

B&S is not liable to cover failures of War-

ranted Parts caused by the use of add-on,

non-original, or modified parts.

5. Maintenance

Any Warranted Part which is not scheduled

for replacement as required maintenance or

which is scheduled only for regular inspec-

tion to the effect of “repair or replace as nec-

essary” shall be warranted as to defects for

the warranty period. Any Warranted Part

which is scheduled for replacement as re-

quired maintenance shall be warranted as to

defects only for the period of time up to the

first scheduled replacement for that part. Any

replacement part that is equivalent in perfor-

mance and durability may be used in the per-

formance of any maintenance or repairs.

The owner is responsible for the perfor-

mance of all required maintenance, as de-

fined in the B&S Operating and Maintenance

Instructions.

6. Consequential Coverage

Coverage hereunder shall extend to the fail-

ure of any engine components caused by

the failure of any Warranted Part still under

warranty.

   '   / , ,  , & ! *A  84;?)?? 5, * *6

>>@)><7

>>;?@;4

>>44><7

>>)9?<?

>>)??49

>>:744?

>9@9<@?

>9@9)?>

>9<;@>;

>99?<77

>9;4:?;

>94:);)

>;@94>?

>;@;)?9

>;?4?@:

>;>:9:4

>;9>9)9

>7<4)>>

>7>@974

>79>::7

>7;@><<

>7;?>);

>749:7>

>7))>>7

>4<;)47

>4>7<94

>4>:94@

>4;4<4<

>47@?:@

>47?999

>47:>?<

>4)7:<7

>4:4>)>

>);9;<?

>);449?

>)79;4>

>))>4)4

>):99;<

>7;?>);

>:<4747

>:??:>7

>:>;:4?

>:;:?>?

>:);<:<

>:)4;4:

9@@47>?

9@:;)4;

9<@;?)9

9<<?>?<

9<94@9)

9<;77;9

9<47)97

9<)@9)7

9<)77<;

9<:@@9<

9<:7:79

9?>9?)7

9?74999

9>;9:49

9>;4?:)

9>4<794

9>)@<;9

9>:>@;<

9>:><9)

9>:9)7:

9;@?>?@

99;<@99

99;>@:)

9;;9:);

99:7)49

99:)4:7

9;@?>?@

974:?@9

97:)>;7

94?)7>7

94>@?)7

94>9?::

94;7<?<

9479@;7

947;:7<

944<;<?

9)@?;4>

9)@?;49

9)@?;44

9)@)<>;

9)<<:>@

9)<>);4

9)9:>?;

9)7<@@>

9:<><@:

9:?:<4@

9:9<9;;

9:;:>;;

9::@4:<

;@@>@9>

;@??<?@

;@??<??

;@?)4)@

;<@9))@

;<?9;;<

;<)@9@7

;?4:>7<

;?)@><4

;>7799>

;>7:;@<

;944:<:

;94:4<<

;9)4;@@

;;979:?

;;7:@<;

 ;?>>4@

 ;9?<@)

 7><)<?

 7?9@>7

 7:@;9?

 7?4<?)

 7>)??)

 79>@9)

 7:@;9?

 7:<<?4

 7:<<?)

Not For Reproduction

(Cette page ne s'applique que pour le Canada et les Etats-Unis)

Déclaration de garantie pour les défauts de contrôle d'émissions pour la Californie, les ÉtatsĆUnis et le Canada.

Le California Air Resources Board (CARB), U.S. EPA et B&S ont le plaisir de vous expliquer la

garantie du système de contrôle des émissions pour votre petit moteur tout terrain. En Californie,

les petits moteurs tout terrain à partir de l'année 2006 doivent être conçus, fabriqués et équipés

pour répondre aux normes sévères antibrouillard de l'état. Ailleurs aux ÉtatsĆUnis, les nouveaux

moteurs tout terrain à allumage commandé par bougie depuis l'année 1997 doivent répondre à

des normes semblables édictées par la U.S. EPA. B&S doit garantir le système de contrôle des

émissions de votre moteur pendant les durées indiquées ciĆaprès, en supposant que le petit

moteur tout terrain ne soit pas mal utilisé, négligé ou que son entretien ne soit pas défectueux.

Le système de contrôle des émissions comprend des pièces comme le carburateur, le filtre à air,

le système d'allumage, la Durit de carburant, le silencieux et le convertisseur catalytique. Des

connecteurs et d'autres assemblages impliqués dans les émissions peuvent aussi en faire partie.

Si la condition de garantie est remplie, Briggs & Stratton réparera gratuitement votre moteur y

compris le diagnostic, les pièces et la mainĆd'Ĺuvre.

Couverture de la garantie de défectuosité du contrôle des émissions de Briggs & Stratton

Les petits moteurs tout terrain sont garantis en ce qui concerne les défauts des pièces du contrôle d'émission pendant une période de deux ans, aux conditions énoncées plus loin. Si une pièce de votre

moteur couverte par cette garantie est défectueuse, Briggs et Stratton la réparera ou la remplacera.

Responsabilités du propriétaire au titre de la garantie

En tant que propriétaire d'un petit moteur non routier, vous êtes responsable de l'entretien nécesĆ

saire indiqué dans les instructions de fonctionnement et d'entretien. Briggs & Stratton recommanĆ

de de conserver toutes les factures de maintenance de votre moteur, mais Briggs & Stratton ne

peut renier la garantie uniquement à cause de l'absence de factures.

En tant que propriétaire d'un moteur non routier, vous devez néanmoins savoir que Briggs &

Stratton peut refuser d'appliquer la garantie si la défectuosité de votre moteur ou d'une partie de

ce moteur est due à un abus, une négligence, un entretien non correct ou des modifications non

approuvées.

Vous avez la responsabilité de confier votre moteur à un Réparateur Agréé Briggs & Stratton dès

que vous découvrez un problème. Les réparations incontestables sous garantie seront

effectuées en un temps raisonnable qui ne doit pas excéder 30 jours.

Si vous avez des questions au sujet de vos droits ou de vos responsabilités quant à la garantie,

veuillez contacter un représentant de Briggs & Stratton au 1Ć414Ć259Ć5262.

La garantie d'émission est une garantie contre des défectuosités. Les défectuosités sont jugées

en fonction des performances normales d'un moteur. La garantie n'est pas liée à un test

d'émission en fonctionnement.

Dispositions de la garantie de défectuosité du contrôle des émissions de Briggs & Stratton

Suivent les dispositions particulières de la couverture de la garantie de défectuosité du contrôle des émissions. Elles viennent en complément de la garantie des moteurs Briggs et Stratton pour

les moteurs non réglementés qui se trouve dans les instructions de fonctionnement et d'entretien.

1. Pièces garanties

La couverture au titre de cette garantie ne s'étend qu'aux pièces énumérées ciĆdessous (celĆ

les du système de contrôle des émissions) dans la mesure où ces pièces étaient présentes

dans le moteur au moment de l'achat.

a. Système de dosage du carburant

• Système d'enrichissement pour démarrages à froid (starter)

• Carburateur et pièces internes

• Pompe à carburant

• Durit et raccords de carburant, colliers

b. Système d'admission d'air

• Filtre à air

• Collecteur d'admission

c. Système d'allumage

• Bougie(s)

• Système d'allumage par volant magnétique

d. Système catalytique

• Convertisseur catalytique

• Collecteur d'échappement

• Système d'injection d'air ou soupape d'impulsion

e. Pièces diverses utilisées dans les systèmes ciĆdessus

• Soupapes et contacteurs de dépression, de température, de position et de durée.

• Raccords et assemblages

2. Durée de la couverture

Briggs & Stratton garantit au propriétaire initial et à tous les acheteurs suivants les pièces

contre tout défaut de matière ou de fabrication qui pourrait entraîner une défectuosité des

pièces garanties pendant une période de deux ans à partir de la date de livraison du moteur à

un acheteur individuel.

3. Gratuité

La réparation ou le remplacement de toute pièce garantie s'effectuera gratuitement pour

l'acheteur, y compris les frais de diagnostic permettant de déterminer qu'une pièce garantie

est défectueuse, si le diagnostic est effectué par un Réparateur Agréé Briggs & Stratton. Pour

bénéficier du service de garantie, veuillez contacter le Réparateur Agréé Briggs & Stratton le

plus proche de chez vous listé dans les Pages Jaunes sous la rubrique « moteurs, essence »,

« moteurs à essence », « tondeuses à gazon » ou autre catégorie semblable.

4. Réclamations et exclusions de garantie

Les réclamations sous garantie seront présentées selon les dispositions de la police de

garantie des moteurs de Briggs & Stratton. La garantie ne couvre pas les pièces qui ne sont

pas des pièces Briggs & Stratton d'origine ou qui ont fait l'objet d'abus, de négligence ou d'un

mauvais entretien ainsi qu'indiqué dans la police de garantie des moteurs de Briggs &

Stratton. Briggs & Stratton n'est pas responsable des défaillances dues à l'utilisation de

pièces rajoutées, non d'origine ou modifiées.

5. Entretien

Toute pièce garantie qui ne doit pas être remplacée au titre de l'entretien ou qui est sujette à

une inspection régulière avec la mention « réparer ou remplacer si besoin est » est garantie

contre tout défaut pendant la période de garantie. Toute pièce dont le remplacement est

prévu au titre de l'entretien n'est garantie contre tout défaut que pendant sa période normale

d'utilisation. Les opérations de maintenance et de réparation doivent utiliser des pièces

équivalentes sur le plan des performances et de la longévité. Le propriétaire est responsable

de l'entretien défini dans les instructions de fonctionnement et d'entretien de Briggs &

Stratton.

6. Couverture des conséquences

La présente couverture s'étend à la défaillance de tout composant du moteur due à la défailĆ

lance d'une pièce encore sous garantie.

Déclaration de garantie du système de contrôle des émissions de Briggs & Stratton Corporation (B&S), du California Air Resources Board (CARB) et de la UniĆ

ted States Environmental Protection Agency (U.S. EPA) (Droits et obligations du propriétaire au titre de la garantie contre tout défaut)

Consultez les informations sur la période de durabilité d'émission et l'INDICE d'air sur l'étiquette d'émission de votre moteur

Les moteurs qui sont certifiés conformes aux normes standards d'émission du California Air Resources Board (CARB) Tier 2, doivent afficher l'information concernant la période de durabilité du système

d'émission et l'INDICE d'air. Cette information est indiquée sur les étiquettes apposées sur les moteurs par Briggs & Stratton. L'étiquette du moteur indiquera les renseignements concernant la certification.

La période de durabilité d'émission indique le nombre d'heures d'utilisation normale pour lequel le moteur est certifié conforme aux normes d'émission sous réserve d'un entretien approprié tel qu'indiqué dans

le manuel d'opération et d'entretien. Les catégories suivantes sont utilisées :

Modéré le moteur est certifié conforme pour 125 heures d'utilisation normale.

Intermédiaire le moteur est certifié conforme pour 250 heures d'utilisation normale.

Prolongé le moteur est certifié conforme pour 500 heures d'utilisation normale.

Par exemple, une tondeuse de modèle standard est utilisée environ 20 à 25 heures par année. Par conséquent, la période de durabilité d'émission d'un moteur dans la catégorie intermédiaire pour ce type de

tondeuse équivaut à 10 à 12 ans.

L'indice d'air est un nombre qui décrit le niveau relatif d'émission pour une catégorie spécifique de moteur. Plus l'indice d'air est bas, plus le moteur est écologique. Cette information est indiquée sous une

forme graphique sur l'étiquette d'émission.

À compter du 1

juillet 2000, surveillez la période de conformité d'émission sur les étiquettes

Après le 1

juillet 2000, certains moteurs B&S seront certifiés conformes aux normes environnementales d'émission standard du United States Environmental Protection Agency (US EPA) Phase 2. Pour les

moteurs certifiés pour la Phase 2, la période de conformité d'émission mentionnée sur les étiquettes indique le nombre d'heures d'utilisation pour lequel le moteur rencontre les normes fédérales. Pour les

moteurs de force moindre que 225 cc, la catégorie C = 125 heures, B = 250 heures et A = 500 heures. Pour les moteurs de 225 cc et plus, la catégorie C = 250 heures, B = 500 heures et A = 1000 heures.

Le remplacement du moteur portant le modèle de série 110000 est 190 cc, 120000 est 206 cc, 200000 est 305 cc, 210000 est 342 cc.

Not For Reproduction