Hisense AEH-W0G2 Guide d'installation

Marque: Hisense

Modèle: AEH-W0G2

Taper: Guide d'installation

Complete Installation

1. Insert foam seal behind the top of the lower window sash and

against the glass of the upper window.

2. Use a drill bit to drill a starter hole through the (3mm)

hole in the top rail.

3. Attach top channel to window sash with one

(19mm)

3/4"

1 /8"

screw to secure window in place.

5.Plug into a grounded 3 prong outlet.

6.Press RESET on the power supply cord. See "Electrical

Requirements".

A.Top of lower window sash

B Foam seal.

Electrical Shock Hazard

Plug into a grounded prong outlet 3 .

Do not remove ground prong .

Do not use an adapter .

Do not use an extension cord .

Failure to follow these instructions can result in death ,

fire or electrical shock, .

WARNING

AIR CONDITIONER USE

Operating your air conditioner properly helps you to obtain the

best possible results.

This section explains proper air conditioner operation.

IMPORTANT:

■If you turn off the air conditioner, wait at least minutes 3

before turning it back on. This prevents the air conditioner

from blowing a fuse or tripping a circuit breaker.

NOTE: In the event of a power failure, your air conditioner will

operate at the previous settings when the power is restored.

■ A operation the better limits:

Outdoor side 64.4~109.4°F (18~43 °C), ≤80%RH; indoor side

62.6~89.6°F (17~32°C), ≤80%RH.

ir conditioner in the Cool mode

Remark a line on the according to less 1/8

(3mm) than the measured width in, then cut the EVA

Foam along the line.

EVA Foam

NOTE:

The EVA Foam is not need to attach for Models:

5K\6K DOE cooling only.

, the side

with should facing the .

Remove the backing from the EVA Foam.

Attach one EVA Foam on the Curtain housing

adhesive Curtain housing

5.Repeat for the right-hand curtain.

A.Curtain housing

B. EVA Foam

4.Check the gap around the unit and seal it with the adhesive

check the gap

seal attached.

The M.Sealing sponge is provide for 5K\6K DOE cooling only

Starting Your Air Conditioner

1. Press the power button to turn on the air conditioner.

■Dry - Dries the room. The air conditioner automatically

selects the temperature. Fan runs on Low speed only.

Fan

NOTE: The Fan button will operate only when the Cool,

Fan or Power Saver mode has been selected.

1. Press FAN until you see the indicator light glow for

the desired setting.

2. Choose High, Med Low.,

■High - for maximum cooling

■Med - for normal cooling

■Low - for quieter cooling

NOTE:

NOTE: When the air conditioner is turned on for the first time

after it is plugged in, the display will show the current set

temperature and will run in the ECO control .

2. Select mode. See "Mode".

3. Select fan speed. See "Fan".

4. Set temperature. See "Temperature ".

Mode

ON/OFF

1. Press MODE repeatedly until you see the indicator light glow

for the desired setting.

2. Choose Fan, Dry, Cool, Eco.

■

Cool -

Eco -

Cools the room.

FAN to select Fan Only mode.

In ECO mode,the Fan will ran at low

■

speed when compressor turn off.

■

ON/OFF

Timer Sleep FilterTimer Sleep Filter

FAN FAN MODE

Low Med High

FAN FAN

Low Med High

Dry

Fan Cool Eco

Dry

Fan Cool Eco

MODE

Dry

Fan Cool Eco

Dry

Fan Cool Eco

MODE

CONNECT

NOTE:

Dry mode should not be used to cool the room.

Select ECO mode to initiate this function. The

fan will continue to run after the compressor shuts off

for 2 minutes(4 minutes for the first time)，so the fan

will shuts off for 10 minutes .The fan then cycles

run for 2 minutes and 10 minutes off intervals

until the room temperature is above the set

temperature, at which time the compressor turns

back on and Cooling resumes. ECO mode is only

available for E-star models.

Fan - Only the fan runs. Press FAN to select High,

Med or Low.

■

Temperature

Press the plus UP button to raise the temperature. Each (∧)

time you press or hold the plus button, the UP (∧)

temperature will go up 1°F (1°C)until it reaches 86°F (30°C).

Press the minus DOWN button to lower the temperature. Each (∨)

time you press or hold the button, the temperature DOWN (∨)

will go down 1°F (1°C) until it reaches 61°F (16°C).

To change the temperature display from F to C ° ° :

Press both the MODE and buttons at the sameDOWN (∨)

t ime for 5 seconds to switch the display from °F to °C.

After cleaning and replace the filter, press the POWER

button for resetting and the FILTER light will go off.

Cools the room and save energy.

IC Warning This device complies with Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause

undesired operation of the device.

The modular can be installed or integrated in mobile or fix devices only. This modular

cannot be installed in any portable device.

For a host manufacture's using a certified modular, if (1) the module's IC number is

not visible when installed in the host, or (2) if the host is marketed so that end users

do not have straightforward commonly used methods for access to remove the

module so that the IC number of the module is visible; then an additional permanent

label referring to the enclosed module: "Contains Transmitter Module IC: "

" or "Contains IC: " must be used.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux

appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions

suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de

l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d'en compromettre le fonctionnement Le modular peut être installé ou

intégré dans un mobile ou réparer une seule chose Installation dans n’importe quel

appareil portable.

Déclaration de rayonnement IC

Ce modular complies avec des radiations émettrices de rayonnement Environnement.

Ceci ne doit pas être co-localisé ou opérer avec des autres Ce modular doit être

installé et obtenu avec une distance minimale de 20 cm entre les radiateurs et le

corps de l’utilisateur.

Pour un hôte, on utilise un modular, si (1) le numéro de module est non visible

Quand on est installé dans le serveur, or (2) si le propriétaire est commercialisé

Straightforward commonly used for the access to remove travail so that the number

IC en vue Le module est visible;Ensuite, le label permanent a été attribué au module:

"Contient le Module IC:" " ou "contenu IC: " doit" be used.

20778-AEHW0G2

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

If the FCC identification number is not visible when the module is installed inside

another device, then the outside of the device into which the module is installed must

also display a label referring to the enclosed module. This exterior label can use

wording such as the following: “Contains Transmitter Module FCC ID:

Or Contains FCC ID: ”

When the module is installed inside another device, the user manual of the host must

contain below warning statements;

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may

cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

The devices must be installed and used in strict accordance with the manufacturer's

instructions as described in the user documentation that comes with the product.

Radiation Exposure Statement

This modular complies with RF radiation exposure limits set forth for an uncontrolled

environment. This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter. This modular must be installed and operated with a

minimum distance of 20 cm between the radiator and user body.

General Statements

(1)Module use PCB antenna, the maximum gain is 0.1dBi.

(2)Any change of antenna type is not allowed, module only use PCB antenna.

(3)Host containing modules must comply with FCC Rule requirements.

2AGCCAEH-W0G2

Requirement per KDB996369 D03

2.2 List of applicable FCC rules

List the FCC rules that are applicable to the modular transmitter. These are the rules

that specifically establish the bands of operation, the power, spurious emissions, and

operating fundamental frequencies. DO NOT list compliance to unintentional-radiator

rules (Part 15 Subpart B) since that is not a condition of a module grant that is

extended to a host manufacturer. See also Section 2.10 below concerning the need to

notify host manufacturers that further testing is required.3

Explanation: This module meets the requirements of FCC part 15.247.

2.3 Summarize the specific operational use conditions

Describe use conditions that are applicable to the modular transmitter, including for

example any limits on antennas, etc. For example, if point-to-point antennas are used

that require reduction in power or compensation for cable loss, then this information

must be in the instructions. If the use condition limitations extend to professional users,

then instructions must state that this information also extends to the host

manufacturer’s instruction manual. In addition, certain information may also be

needed, such as peak gain per frequency band and minimum gain, specifically for

master devices in 5 GHz DFS bands.

Explanation: The EUT has a PCB Antenna, and the antenna use a permanently attached antenna which

is not replaceable.

2.4 Limited module procedures

If a modular transmitter is approved as a “limited module,” then the module

manufacturer is responsible for approving the host environment that the limited

module is used with. The manufacturer of a limited module must describe, both in the

filing and in the installation instructions, the alternative means that the limited module

manufacturer uses to verify that the host meets the necessary requirements to satisfy

the module limiting conditions.

A limited module manufacturer has the flexibility to define its alternative method to

address the conditions that limit the initial approval, such as: shielding, minimum

signaling amplitude, buffered modulation/data inputs, or power supply regulation. The

alternative method could include that the limited module manufacturer reviews

detailed test data or host designs prior to giving the host manufacturer approval.

This limited module procedure is also applicable for RF exposure evaluation when it is

necessary to demonstrate compliance in a specific host. The module manufacturer

must state how control of the product into which the modular transmitter will be

installed will be maintained such that full compliance of the product is always ensured.

For additional hosts other than the specific host originally granted with a limited

module, a Class II permissive change is required on the module grant to register the

additional host as a specific host also approved with the module.

Explanation: This module is limited to use in air conditioners.

2.5 Trace antenna designs

For a modular transmitter with trace antenna designs, see the guidance in Question

11 of KDB Publication 996369 D02 FAQ – Modules for Micro-Strip Antennas and

traces. The integration information shall include for the TCB review the integration

instructions for the following aspects: layout of trace design, parts list (BOM), antenna,

connectors, and isolation requirements.

a) Information that includes permitted variances (e.g., trace boundary limits, thickness,

length, width, shape(s), dielectric constant, and impedance as applicable for each

type of antenna);

b) Each design shall be considered a different type (e.g., antenna length in multiple(s)

of frequency, the wavelength, and antenna shape (traces in phase) can affect

antenna gain and must be considered);

c) The parameters shall be provided in a manner permitting host manufacturers to

design the printed circuit (PC) board layout;

d) Appropriate parts by manufacturer and specifications;

e) Test procedures for design verification; and

f) Production test procedures for ensuring compliance.

The module grantee shall provide a notice that any deviation(s) from the defined

parameters of the antenna trace, as described by the instructions, require that the

host product manufacturer must notify the module grantee that they wish to change

the antenna trace design. In this case, a Class II permissive change application is

required to be filed by the grantee, or the host manufacturer can take responsibility

through the change in FCC ID (new application) procedure followed by a Class II

permissive change application.

Explanation: Yes, The module with trace antenna designs, and This manual has been shown the layout

of trace design, antenna, connectors, and isolation requirements.

2.6 RF exposure considerations

It is essential for module grantees to clearly and explicitly state the RF exposure

conditions that permit a host product manufacturer to use the module. Two types of

instructions are required for RF exposure information: (1) to the host product

manufacturer, to define the application conditions (mobile, portable – xx cm from a

person’s body); and (2) additional text needed for the host product manufacturer to

provide to end users in their end-product manuals. If RF exposure statements and

use conditions are not provided, then the host product manufacturer is required to

take responsibility of the module through a change in FCC ID (new application).

Explanation: This module complies with FCC RF radiation exposure limits set forth

for an uncontrolled environment, This equipment should be installed and operated

with a minimum distance of 20 centimeters between the radiator and your body." This

module is designed to comply with the FCC statement, FCC ID is: .

2AGCCAEH-W0G2

2.7 Antennas

A list of antennas included in the application for certification must be provided in the

instructions. For modular transmitters approved as limited modules, all applicable

professional installer instructions must be included as part of the information to the

host product manufacturer. The antenna list shall also identify the antenna types

(monopole, PIFA, dipole, etc. (note that for example an “omni-directional antenna” is

not considered to be a specific “antenna type”)).

For situations where the host product manufacturer is responsible for an external

connector, for example with an RF pin and antenna trace design, the integration

instructions shall inform the installer that unique antenna connector must be used on

the Part 15 authorized transmitters used in the host product. The module

manufacturers shall provide a list of acceptable unique connectors.

Explanation: The EUT has a PCB Antenna, and the antenna use a permanently attached antenna which

is unique.

2.8 Label and compliance information

Grantees are responsible for the continued compliance of their modules to the FCC

rules. This includes advising host product manufacturers that they need to provide a

physical or e-label stating “Contains FCC ID” with their finished product. See

Guidelines for Labeling and User Information for RF Devices – KDB Publication

784748.

Explanation: The host system using this module, should have label in a visible area

indicated the following texts: “Contains FCC ID: , Contains IC:

”

2.9 Information on test modes and additional testing requirements5

Additional guidance for testing host products is given in KDB Publication 996369 D04

Module Integration Guide. Test modes should take into consideration different

operational conditions for a stand-alone modular transmitter in a host, as well as for

multiple simultaneously transmitting modules or other transmitters in a host product.

The grantee should provide information on how to configure test modes for host

product evaluation for different operational conditions for a stand-alone modular

transmitter in a host, versus with multiple, simultaneously transmitting modules or

other transmitters in a host.

Grantees can increase the utility of their modular transmitters by providing special

means, modes, or instructions that simulates or characterizes a connection by

enabling a transmitter. This can greatly simplify a host manufacturer’s determination

that a module as installed in a host complies with FCC requirements.

Explanation: Top band can increase the utility of our modular transmitters by providing instructions that

simulates or characterizes a connection by enabling a transmitter.

2AGCCAEH-W0G2

2.10 Additional testing, Part 15 Subpart B disclaimer

The grantee should include a statement that the modular transmitter is only FCC

authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant,

and that the host product manufacturer is responsible for compliance to any other

FCC rules that apply to the host not covered by the modular transmitter grant of

certification. If the grantee markets their product as being Part 15 Subpart B compliant

(when it also contains unintentional-radiator digital circuity), then the grantee shall

provide a notice stating that the final host product still requires Part 15 Subpart B

compliance testing with the modular transmitter installed.

Explanation: The module without unintentional-radiator digital circuity, so the module does not require

an evaluation by FCC Part 15 Subpart B. The host shoule be evaluated by the FCC Subpart B.

Hisense AEH-W0G2 Guide d'installation

Marque: Hisense

Modèle: AEH-W0G2

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Hisense AEH-W0G2 Installation guide

Hisense AEH-W0G2 Guide d'installation

Hisense AEH-W0G2 Guide d'installation

dans d''autres langues

Autres documents