DeWalt DCCS670T1WS620B Manuel utilisateur

Marque: DeWalt

Modèle: DCCS670T1WS620B

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT

Instruction Manual

Guide D’utilisation

Manual de instrucciones

DCCS670

60V Cordless Chainsaw

Scie à chaîne sans fil 60 V

Sierra de cadena inalámbrica de 60 V

final page size: 8.5 x 5.5 in

ENGLISH

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 17

Español (traducido de las instrucciones originales) 34

ENGLISH

English (original instructions)

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.

(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.

WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

If you have any questions or comments about this or

any

DeWALT

tool, call us toll free at:

1-800-4-

DeWALT

(1-800-433-9258).

1 Variable speed trigger

switch

2 Lock-off lever

3 Chain brake / front hand

guard

4 Guide bar

5 Saw chain

6 Sprocket cover

7 Battery Pack

8 Bar adjust locking knob

9 Chain tensioning knob

10 Oil level indicator

11 Guide bar scabbard

12 Rear handle

13 Front handle

14 Battery housing

15 Battery release button

16 Oil cap (not shown)

Fig. A

ENGLISH

GENERAL POWER TOOL SAFETY

WARNINGS

WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust orfumes.

c ) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electricshock.

f ) If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personalinjuries.

c ) Prevent unintentional starting. Ensure the

switch is in the off position before connecting to

power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your

finger on the switch or energizing power tools that

have the switch on invitesaccidents.

d ) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personalinjury.

e ) Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewelry or

long hair can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-relatedhazards.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct

power tool for your application. The correct power

tool will do the job better and safer at the rate for

which it wasdesigned.

b ) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

berepaired.

c ) Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power

toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are

caused by poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking

ENGLISH

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result

in a hazardoussituation.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury andfire.

c ) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws, or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or afire.

d ) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, flush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from

the battery may cause irritation orburns.

6) Service

a ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool ismaintained.

Chainsaw Safety Warnings

WARNING: Additional safety warnings for

chainsaws.

• Keep all parts of the body away from the saw chain

when the chain saw is operating. Before you start

the chain saw, make sure the saw chain is not

contacting anything. A moment of inattention while

operating chain saws may cause entanglement of your

clothing or body with the sawchain.

• Always hold the chain saw with your right hand

on the rear handle and your left hand on the front

handle. Holding the chain saw with a reversed hand

configuration increases the risk of personal injury and

should never bedone.

• Hold the power tool by insulated gripping surfaces

only, because the saw chain may contact hidden

wiring. Saw chains contacting a "live" wire may make

exposed metal parts of the power tool "live" and could give

the operator an electricshock.

• Wear safety glasses and hearing protection. Further

protective equipment for head, hands, legs and

feet is recommended. Adequate protective clothing

will reduce personal injury by ﬂying debris or accidental

contact with the sawchain.

• Do not operate a chain saw in a tree. Operation of a

chain saw while up in a tree may result in personalinjury.

• Always keep proper footing and operate the chain

saw only when standing on ﬁxed, secure and level

surface. Slippery or unstable surfaces such as ladders may

cause a loss of balance or control of the chainsaw.

• When cutting a limb that is under tension be alert

for spring back. When the tension in the wood ﬁbers is

released the spring loaded limb may strike the operator

and/or throw the chain saw out ofcontrol.

• Use extreme caution when cutting brush and

saplings. The slender material may catch the saw chain

and be whipped toward you or pull you offbalance.

• Carry the chain saw by the front handle with the

chain saw switched off and away from your body.

When transporting or storing the chain saw always

ﬁt the guide bar cover. Proper handling of the chain

saw will reduce the likelihood of accidental contact with

the moving sawchain.

• Follow instructions for lubricating, chain tensioning

and changing accessories. Improperly tensioned or

lubricated chain may either break or increase the chance

forkickback.

• Keep handles dry, clean, and free from oil and

grease. Greasy, oily handles are slippery causing loss

ofcontrol.

• Cut wood only. Do not use chain saw for purposes

not intended. For example: do not use chain saw

for cutting plastic, masonry or non-wood building

materials. Use of the chain saw for operations different

than intended could result in a hazardoussituation.

Causes and Operator Prevention of

Kickback:

Kickback may occur when the nose or tip of the guide bar

touches an object, or when the wood closes in and pinches

the saw chain in thecut.

Tip contact in some cases may cause a sudden reverse

reaction, kicking the guide bar up and back towards

theoperator.

Pinching the saw chain along the top of the guide bar may

push the guide bar rapidly back towards theoperator.

Either of these reactions may cause you to lose control of

the saw which could result in serious personal injury. Do not

rely exclusively upon the safety devices built into your saw.

As a chain saw user, you should take several steps to keep

your cutting jobs free from accident orinjury.

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below:

• Maintain a firm grip, with thumbs and ﬁngers

encircling the chain saw handles, with both hands

on the saw and position your body and arm to allow

you to resist kickback forces. Kickback forces can be

controlled by the operator, if proper precautions are taken.

Do not let go of the chainsaw.

• Do not overreach and do not cut above shoulder

height. This helps prevent unintended tip contact

and enables better control of the chain saw in

unexpectedsituations.

ENGLISH

• Only use replacement bars and chains speciﬁed

by the manufacturer. Incorrect replacement bars and

chains may cause chain breakage and/orkickback.

• Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to

increasedkickback.

The Following Precautions Should Be

Followed to Minimize Kickback:

1 . Grip saw firmly. Hold the chain saw firmly with both

hands when the motor is running. Use a firm grip

with thumbs and fingers encircling the chain saw

handles. Chain saw will pull forward when cutting on the

bottom edge of the bar, and push backward when cutting

along the top edge of thebar.

2 . Do not overreach.

3 . Keep proper footing and balance at alltimes.

4 . Don’t let the nose of the guide bar contact a log,

branch, ground or otherobstruction.

5 . Don’t cut above shoulderheight.

6 . Use devices such as low kickback chain and reduced

kickback guide bars that reduce the risks associated

withkickback.

7 . Only use replacement bars and chains specified by

the manufacturer or theequivalent.

8 . Never let the moving chain contact any object at the

tip of the guidebar.

9 . Keep the working area free from obstructions such

as other trees, branches, rocks, fences, stumps, etc.

Eliminate or avoid any obstruction that your saw chain

could hit while you are cutting through a particular log

orbranch.

10 . Keep your saw chain sharp and properly tensioned.

A loose or dull chain can increase the chance of

kickback. Check tension at regular intervals with the

motor stopped and tool unplugged, never with the

motorrunning.

11 . Begin and continue cutting only with the chain

moving at full speed. If the chain is moving at a slower

speed, there is a greater chance for kickback tooccur.

12 . Cut one log at atime.

13 . Use extreme caution when re-entering a previous

cut. Engage ribbed bumpers into wood and allow chain

to reach full speed before proceeding withcut.

14 . Do not attempt plunge cuts or borecuts.

15 . Watch for shifting logs or other forces that could

close a cut and pinch or fall intochain.

Kickback Safety Features

WARNING: The following features are included

on your saw to help reduce the hazard of kickback;

however such features will not totally eliminate this

dangerous reaction. As a chain saw user do not rely

only on safety devices. You must follow all safety

precautions, instructions, and maintenance in this

manual to help avoid kickback and other forces which

can result in seriousinjury.

• Reduced-Kickback Guide Bar, designed with a small radius

tip which reduces the size of the kickback danger zone on

bar tip. A reduced - kickback guide bar is one which has

been demonstrated to significantly reduce the number

and seriousness of kickbacks when tested in accordance

with safety requirements for electric chainsaws.

• Low-Kickback Chain, designed with a contoured depth

gauge and guard link which deflect kickback force

and allow wood to gradually ride into the cutter. A

low-kickback chain is a chain which has met kickback

performance requirements of ANSI B175.1–2012.

• Do not operate chain saw while in a tree, on a ladder, on a

scaffold, or from any unstablesurface.

• Hold tool by insulated gripping surfaces when performing

an operation where the cutting tool may contact hidden

wiring. Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock theoperator.

• Do not attempt operations beyond your capacity or

experience. Read thoroughly and understand completely

all instructions in thismanual.

• Before you start chain saw, make sure saw chain is not

contacting anyobject.

• Do not operate a chain saw with one hand! Serious injury

to the operator, helpers, or bystanders may result from

one handed operation. A chain saw is intended for two-

handed useonly.

• Keep the handles dry, clean, and free of oil orgrease.

• Do not allow dirt, debris, or sawdust to build up on the

motor or outside airvents.

• Stop the chain saw before setting itdown.

• Do not cut vines and/or small underbrush.

• Use extreme caution when cutting small size brush and

saplings because slender material may catch the saw

chain and be whipped toward you or pull you offbalance.

WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-

treatedlumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are

specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and

ENGLISH

wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmfulchemicals.

WARNING: Use of this tool can generate and/

or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use

NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles

away from face andbody.

Chainsaw Names and Terms

• Bucking - The process of cross cutting a felled tree or log

intolengths.

• Motor Brake - A device used to stop the saw chain when

the trigger isreleased.

• Chain Saw Powerhead - A chain saw without the saw

chain and guidebar.

• Drive Sprocket or Sprocket - The toothed part that drives

the sawchain.

• Felling - The process of cutting down atree.

• Felling Back Cut - The final cut in a tree felling operation

made on the opposite side of the tree from the

notchingcut.

• Front Handle - The support handle located at or toward

the front of the chainsaw.

• Front Hand Guard - A structural barrier between the front

handle of a chain saw and the guide bar, typically located

close to the hand position on the fronthandle.

• Guide Bar - A solid railed structure that supports and

guides the sawchain.

• Guide Bar Scabbard - Enclosure fitted over guide bar to

prevent tooth contact when saw is not inuse.

• Kickback - The backward or upward motion, or both of the

guide bar occurring when the saw chain near the nose of

the top area of the guide bar contacts any object such as a

log or branch, or when the wood closes in and pinches the

saw chain in thecut.

• Kickback, Pinch - The rapid pushback of the saw which

can occur when the wood closes in and pinches the

moving saw chain in the cut along the top of the

guidebar.

• Kickback, Rotational - The rapid upward and backward

motion of the saw which can occur when the moving saw

chain near the upper portion of the tip of the guide bar

contacts an object, such as a log orbranch.

• Limbing - Removing the branches from a fallen tree

• Low-Kickback Chain - A chain that complies with the

kickback performance requirements of ANSI B175.1–2012

(when tested on a representative sample of chain saws.)

• Normal Cutting Position - Those positions assumed in

performing the bucking and fellingcuts.

• Notching Undercut - A notch cut in a tree that directs the

tree’sfall.

• Rear Handle - The support handle located at or toward the

rear of thesaw.

• Reduced Kickback Guide Bar - A guide bar which has been

demonstrated to reduce kickbacksignificantly.

• Replacement Saw Chain - A chain that complies with

kickback performance requirements of ANSI B175.1–2000

when tested with specific chain saws. It may not meet

the ANSI performance requirements when used with

othersaws.

• Saw Chain - A loop of chain having cutting teeth, that cut

the wood,and that is driven by the motor and is supported

by the guidebar.

• Ribbed Bumper - The ribs used when felling or bucking to

pivot the saw and maintain position whilesawing.

• Switch - A device that when operated will complete or

interrupt an electrical power circuit to the motor of the

chainsaw.

• Switch Linkage - The mechanism that transmits motion

from a trigger to theswitch.

• Switch Lockout - A movable stop that prevents

the unintentional operation of the switch until

manuallyactuated.

Additional Safety Information

WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.

WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearingloss.

CAUTION: When not in use, place tool on its

base on a stable surface where it will not cause

a tripping or falling hazard. Some tools with large

battery packs will stand upright on the battery pack

but may be easily knockedover.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be

caught in movingparts.

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

...................... Class I

Construction

(grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per

minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

or AC ...........alternating current

or AC/DC .... alternating or

direct current

...................... Class II

Construction

(double insulated)

no .......................no load speed

n .........................rated speed

......................earthing terminal

ENGLISH

.............safety alert symbol

.............Visible radiation

............. Wear respiratory

protection

............. Wear eye protection

............. Wear hearing

protection

............. Read all documentation

CSPM .......... Cut strokes per minute

............. Do not leave in rain

............ Tip contact can cause

the guide bar to move

suddenly upward and

backward, which can

cause serious injury

............ Contact of the guide

bar tip with any object

should be avoided

........... Rotational direction of

the saw chain

...... Always use two hands

when operating the

chainsaw

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

Your tool uses a

DeWALT

charger. Be sure to read all safety

instructions before using your charger. Consult the chart

at the end of this manual for compatibility of chargers and

batterypacks.

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs

WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or seriousinjury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into

a non-compatible charger as battery pack may

rupture causing serious personal injury. Consult

the chart at the end of this manual for compatibility of

batteries andchargers.

• Charge the battery packs only in designated

DeWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is

severely damaged or is completely worn out. The

battery pack can explode in a fire. Toxic fumes and

materials are created when lithium ion battery packs

areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of

a mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.

WARNING: Burn hazard. Battery liquid may be

flammable if exposed to spark orflame.

WARNING: Fire hazard. Never attempt to open the

battery pack for any reason. If the battery pack case

is cracked or damaged, do not insert into the charger.

Do not crush, drop or damage the battery pack. Do

not use a battery pack or charger that has received a

sharp blow, been dropped, run over or damaged in

any way (e.g., pierced with a nail, hit with a hammer,

stepped on). Damaged battery packs should be

returned to the service center forrecycling.

Transportation

WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do

not place the battery pack in aprons, pockets, tool

boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries

can possibly cause fires if the battery terminals

inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the

like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes in

carry-on baggage UNLESS they are properly protected

from short circuits. So when transporting individual

battery packs, make sure that the battery terminals

are protected and well insulated from materials that

could contact them and cause a shortcircuit.

Shipping the

DeWALT

FLEXVOLT™ Battery

The D

WALT FLEXVOLT™ battery has two modes: Use and

Shipping.

Use Mode: When the FLEXVOLT™ battery stands alone or is

in a D

WALT 20V Max* product, it will operate as a 20V Max*

battery. When the FLEXVOLT™ battery is in a 60V Max* or a

120V Max* (two 60V Max* batteries) product, it will operate

as a 60V Max* battery.

Shipping Mode: When

the cap is attached to the

FLEXVOLT™ battery, the

battery is in Shipping Mode.

Strings of cells are electrically

disconnected within the pack resulting in three batteries

with a lower Watt hour (Wh) rating as compared to one

battery with a higher Watt hour rating. This increased

quantity of three batteries with the lower Watt hour rating

ENGLISH

can exempt the pack from certain shipping regulations that

are imposed upon the higher Watt hourbatteries.

The battery label indicates two Watt hour ratings (see

example). Depending on how the battery is shipped, the

appropriate Watt hour rating must be used to determine

the applicable shipping requirements. If utilizing the

shipping cap, the pack will be considered 3 batteries at

the Watt hour rating indicated for “Shipping”. If shipping

without the cap or in a tool, the pack will be considered one

battery at the Watt hour rating indicated next to “Use”.

USE: 120 Wh Shipping: 3 x 40 Wh

Example of Use and Shipping Label Marking

For example, Shipping Wh rating might indicate 3 x 40 Wh,

meaning 3 batteries of 40 Watt hours each. The Use Wh

rating might indicate 120 Wh (1 battery implied).

Fuel Gauge Battery Packs (Fig. B)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

The fuel gauge is an indication of approximate levels of

charge remaining in the battery pack according to the

followingindicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

To actuate the fuel gauge, press and hold the fuel gauge

button. A combination of the three green LED lights will

illuminate designating the level of charge left. When the

level of charge in the battery is below the usable limit, the

fuel gauge will not illuminate and the battery will need to

berecharged.

Fig. B

NOTE: The fuel gauge is only an indication of the charge left

on the battery pack. It does not indicate tool functionality

and is subject to variation based on product components,

temperature and end-userapplication.

For more information regarding fuel gauge battery packs,

please contact call 1-800-4-

DeWALT

(1-800-433-9258) or

visit our website www.dewalt.com.

The RBRC® Seal

The RBRC® (Rechargeable Battery

Recycling Corporation) Seal on the nickel

cadmium, nickel metal hydride or lithium-

ion batteries (or battery packs) indicates

that the costs to recycle these batteries

(or battery packs) at the end of their useful life have already

been paid by

DeWALT

. In some areas, it is illegal to place

spent nickel cadmium, nickel metal hydride or lithium-ion

batteries in the trash or municipal solid waste stream and

the Call2Recycle® program provides an environmentally

consciousalternative.

Call 2 Recycle, Inc., in cooperation with

DeWALT

and other

battery users, has established the program in the United

States and Canada to facilitate the collection of spent nickel

cadmium, nickel metal hydride or lithium-ion batteries. Help

protect our environment and conserve natural resources by

returning the spent nickel cadmium, nickel metal hydride

or lithium-ion batteries to an authorized

DeWALT

service

center or to your local retailer for recycling. You may also

contact your local recycling center for information on

where to drop off the spent battery. RBRC® is a registered

trademark of Call 2 Recycle,Inc.

Important Safety Instructions for All

Battery Chargers

WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or seriousinjury.

• DO NOT attempt to charge the battery pack with

any chargers other than the ones in this manual.

The charger and battery pack are specifically designed to

worktogether.

• These chargers are not intended for any uses other

than charging

DeWALT

rechargeable batteries.

Any other uses may result in risk of fire, electric shock

orelectrocution.

• Do not expose the charger to rain orsnow.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected

to damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the greater the capacity

of the cable, that is, 16 gauge has more capacity than 18

gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using

more than one extension to make up the total length,

be sure each individual extension contains at least the

minimum wire size. The following table shows the correct

size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge. The

lower the gauge number, the heavier thecord.

ENGLISH

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet

(meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

610 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or

place the charger on a soft surface that might block

the ventilation slots and result in excessive internal

heat. Place the charger in a position away from any heat

source. The charger is ventilated through slots in the top

and the bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

WARNING: Shock hazard. Do not allow any liquid to

get inside the charger. Electric shock mayresult.

WARNING: Burn hazard. Do not submerge the

battery pack in any liquid or allow any liquid to

enter the battery pack. Never attempt to open the

battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service

center forrecycling.

CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DeWALT

rechargeable battery packs.

Other types of batteries may overheat and burst

resulting in personal injury and propertydamage.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the charger can

be shorted by foreign material. Foreign materials

of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum

foil or any buildup of metallic particles should be

kept away from the charger cavities. Always unplug

the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before

attempting toclean.

Charging a Battery (Fig. A)

1. Plug the charger into an appropriate outlet before

inserting batterypack.

2. Insert the battery pack 7 into the charger, making sure

the battery pack is fully seated in the charger. The red

(charging) light will blink continuously indicating that

the charging process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is

fully charged and may be used at this time or left in the

charger. To remove the battery pack from the charger,

push the battery release button 15 on the batterypack.

NOTE: To ensure maximum performance and life of lithium-

ion battery packs, charge the battery pack fully before

firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

Charging

Fully Charged

Hot/Cold Pack Delay*

* The red light will continue to blink, but a yellow indicator

light will be illuminated during this operation. Once the

battery pack has reached an appropriate temperature, the

yellow light will turn off and the charger will resume the

chargingprocedure.

The compatible charger(s) will not charge a faulty battery

pack. The charger will indicate faulty battery pack by

refusing to light or by displaying a problem pack or charger

blinkpattern.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and

battery pack to be tested at an authorized servicecenter.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan

designed to cool the battery pack. The fan will turn on

automatically when the battery pack needs to becooled.

Never operate the charger if the fan does not operate

properly or if ventilation slots are blocked. Do not permit

foreign objects to enter the interior of thecharger.

ENGLISH

Electronic Protection System

Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against

overloading, overheating or deepdischarge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the lithium-

ion battery pack on the charger until it is fullycharged.

Wall Mounting

These chargers are designed to be wall mountable or to

sit upright on a table or work surface. If wall mounting,

locate the charger within reach of an electrical outlet,

and away from a corner or other obstructions which may

impede air flow. Use the back of the charger as a template

for the location of the mounting screws on the wall. Mount

the charger securely using drywall screws (purchased

separately) at least 1" (25.4 mm) long, with a screw head

diameter of 0.28–0.35" (7–9mm), screwed into wood to an

optimal depth leaving approximately 7/32" (5.5 mm) of the

screw exposed. Align the slots on the back of the charger

with the exposed screws and fully engage them in theslots.

Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non-metallic brush. Do not use water or

any cleaningsolutions.

Important Charging Notes

1. Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18° – 24°C). DO NOT charge

the battery pack in an air temperature below +40°F

(+4.5°C), or above +104°F (+40°C). This is important

and will prevent serious damage to the batterypack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulatedtrailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out the

lights;

c. Move the charger and battery pack to a location

where the surrounding air temperature is

approximately 65°F – 75°F (18° – 24°C);

d. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

4. The battery pack should be recharged when it fails to

produce sufficient power on jobs which were easily

done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may

also charge a partially used pack whenever you desire

with no adverse effect on the batterypack.

5. Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Always

unplug the charger from the power supply when there

is no battery pack in the cavity. Unplug the charger

before attempting toclean.

6. Do not freeze or immerse the charger in water or any

otherliquid.

Storage Recommendations

1. The best storage place is one that is cool and dry, away

from direct sunlight and excess heat orcold.

2. For long storage, it is recommended to store a fully

charged battery pack in a cool dry place out of the

charger for optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be

recharged beforeuse.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part

of it. Damage or personal injury couldresult.

Refer to Figure A at the beginning of this manual for a

complete list ofcomponents.

INTENDED USE

Your

DeWALT

DCCS670 Chainsaw is ideal for pruning

applications and cutting logs up to 14" (355 mm)

indiameter.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

This chainsaw is a professional powertool. DO NOT let

children come into contact with the tool. Supervision is

required when inexperienced operators use thistool.

ASSEMBLY

Installing the Guide Bar and Saw Chain

(Fig. A, D–F, H)

CAUTION: Sharp chain. Always wear protective

gloves when handling the chain. The chain is sharp

and can cut you when it is notrunning.

WARNING: Sharp moving chain. To prevent

accidental operation, ensure that battery is removed

from the tool before performing the following

operations. Failure to do this could result in serious

personalinjury.

If the saw chain 5 and guide bar 4 are packed separately

in the carton, the chain has to be attached to the bar, and

both must be attached to the body of thetool.

• Place the saw on a flat, firmsurface.

ENGLISH

• Flip up locking lever and rotate the bar adjust locking

knob 8 counterclockwise as shown in FigureD to

remove sprocket cover 6.

• Wearing protective gloves, grasp the saw chain 5 and

wrap it around the guide bar 4, ensuring the teeth are

facing the correct direction (see FigureH).

• Ensure the chain is properly set in the slot around the

entire guidebar.

• Place the saw chain around the sprocket 18. While

lining up the slot on the guide bar with chain tensioning

pin 20, and the bolt 19, on the base of the tool as

shown in FigureE.

• Once in place, hold the bar still, replace sprocket

cover 6. Make sure tool-free tension assembly bolt

hole on the cover lines up with the bolt 19, in the

main housing. Flip up locking lever and rotate the bar

adjust locking knob 8 clockwise until it clicks, then

loosen knob one full turn, so that the saw chain can be

properlytensioned.

• Rotate the chain tensioning knob 9 clockwise to

increase tension as shown in FigureF. Make sure the

saw chain 5 is snug around the guide bar 4. Tighten

the bar adjust locking knob until it clicks. The bar is

secure after three audible clicks are heard. Further

tightening is notrequired.

Fig. D

Fig. E

18 19

Fig. F

Adjusting Chain Tension (Fig. A, G )

CAUTION: Sharp chain. Always wear protective

gloves when handling the chain. The chain is sharp

and can cut you when it is notrunning.

WARNING: Sharp moving chain. To prevent

accidental operation, ensure that battery is removed

from the tool before performing the following

operations. Failure to do this could result in serious

personalinjury.

• With the saw on a flat, firm surface, check the saw chain

5 tension. The tension is correct when the chain snaps

back after being pulled 1/8" (3mm) away from the

guide bar 4 with light force from the index finger and

thumb as shown in FigureI. There should be no “sag”

between the guide bar and the chain on the underside

as shown in FigureG.

• To adjust saw chain tension, flip up locking tab and

rotate the bar adjust locking knob 8 counterclockwise

one full turn. Rotate the chain tensioning knob

9 clockwise until the chain tension is correct as

instructedabove.

• Do not over-tension the chain as this will lead to

excessive wear and will reduce the life of the bar

andchain.

• Once chain tension is correct, securely tighten bar adjust

lockingknob.

NOTE: The bar adjust locking knob has a detent tightening

system. The sprocket cover is secure after three audible

clicks are heard. Further tigtening is notrequired.

• When the chain is new, check the tension frequently

(after removing battery) during the first 2 hours of use as

a new chain stretchesslightly.

Fig. G

1/8” (3mm)

ENGLISH

Replacing the Saw Chain (Fig. A, H)

CAUTION: Sharp chain. Always wear protective

gloves when handling the chain. The chain is sharp

and can cut you when it is notrunning.

WARNING: Sharp moving chain. To prevent

accidental operation, ensure that battery is removed

from the tool before performing the following

operations. Failure to do this could result in serious

personalinjury.

• Flip up locking tab and rotate the bar adjust locking

knob 8 counterclockwise to release chaintension.

• Remove sprocket cover 6 as described in Installing the

Guide Bar and Saw Chainsection.

• Lift the worn saw chain 5 out of the groove in the

guide bar 4.

• Place the new chain in the slot of the guide bar, making

sure the saw teeth are facing the correct direction by

matching the arrow on the chain with the graphic on

the sprocket cover 6 shown in FigureH.

• Follow instructions for Installing the Guide Bar and

SawChain.

Fig. H

Replacement chain and bar are available from your

nearest

DeWALT

servicecenter.

• DCCS670 requires replacement chain service part

number N594321. Replacement 16” bar, service part

numberN594320.

Saw Chain and Guide Bar Oiling (Fig. I)

Auto Oiling System

This chain saw is equipped with an auto oiling system that

keeps the saw chain and guide bar constantly lubricated.

The oil level indicator 10 shows the level of the oil in the

chain saw. If the oil level is less than a quarter full, remove

the battery from the chain saw and refill with the correct

type of oil. Always empty oil tank when finishedcutting.

NOTE: Use a high quality bar and chain oil for proper chain

and bar lubrication. As a temporary substitute, a non-

detergent SAE30 weight motor oil can be used. The use of

a vegetable based bar and chain oil is recommended when

pruning trees. Mineral oil is not recommended because it

may harm trees. Never use waste oil or very thick oil. These

may damage yourchainsaw.

Filling the Oil Reservoir

• Flip down locking lever and unscrew counterclockwise

a quarter turn and then remove the oil cap 16. Fill

the reservoir with the recommended bar and chain oil

until the oil level has reached the top of the oil level

indicator10.

• Refit the oil cap and tighten clockwise a quarter turn.

Flip up locking lever to its lockedposition.

• Periodically switch the chain saw off and check the oil

level indicator to ensure the bar and chain are being

properlyoiled.

Fig. L

Transporting Saw (Fig. A, J)

• Always remove the battery from the tool and cover the

guide bar 4 with the scabbard 11 (see FigureJ) when

transporting thesaw.

• Engage chain brake by pushing chain brake / front hand

guard 3forward.

Fig. J

OPERATION

WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Installing and Removing the Battery Pack

(Fig. K, L)

NOTE: For best results, make sure your battery pack is

fullycharged.

To Install the Battery Pack into the Tool

1. Align the battery pack 7 with the rails inside the tool

(see FigureK).

2. Slide it into the tool until the battery pack is firmly

seated and ensure that you hear the lock snap

intoplace.

To Remove the Battery Pack from the

Tool

1. Press the release button 15 and firmly pull the battery

pack out of the toolhandle (see FigureL).

2. Insert battery pack into the charger as described in the

charger section of thismanual.

ENGLISH

Fig. K

Fig. L

Proper Hand Position (Fig. A, M)

WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position as shown.

WARNING:

To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires the left hand on the front

handle 13, with the right hand on the rear handle 12.

Fig. M

Operating the Chain Saw (Fig. A, N–O)

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below

may result in electric shock, fire and/or serious

personalinjury.

• Guard Against Kickback which can result in severe

injury or death. See Important Safety Instructions

Guard Against Kickback, to avoid the risk

ofkickback.

• Do not overreach. Do not cut above chest height.

Make sure your footing is firm. Keep feet apart.

Divide your weight evenly on bothfeet.

• Use a firm grip with your left hand on the front

handle 13 and your right hand on the rear

handle 12 so that your body is to the left of the

guidebar.

• Do not hold chain saw by front hand guard/

chain brake 3. Keep elbow of left arm locked so

that left arm is straight to withstand akickback.

WARNING: Never use a cross-handed grip (left

hand on the rear handle and right hand on the

fronthandle).

WARNING: Never allow any part of your body to

be in line with the guide bar 4 when operating the

chainsaw.

• Never operate while in a tree, in any awkward

position or on a ladder or other unstable surface.

You may lose control of saw causing severeinjury.

• Keep the chain saw running at full speed the entire

time you arecutting.

• Allow the chain to cut for you. Exert only light

pressure. Do not put pressure on chain saw at

end ofcut.

WARNING: When not in use always have the

chain brake engaged and batteryremoved.

On / Off Switch

Always be sure of your footing and grip the chain saw firmly

with both hands with the thumb and fingers encircling

bothhandles.

This tool is equipped with a variable speed trigger switch.

To turn the unit on, ensure chain brake is not engaged. Push

down on the the lock off lever 2, shown in FigureN, and

squeeze the trigger switch 1. Once the unit is running, you

may release the lock off lever. The farther you depress the

trigger, the faster it willoperate.

In order to keep the unit running you must continue to

squeeze the trigger. To turn the unit off, release thetrigger.

NOTE: If too much force is applied while making a cut the

saw will turn off. To restart saw, you must release the lock off

lever 2 and the trigger switch 1 before the saw will restart.

Begin your cut again this time with less force. Allow the saw

to cut at its ownpace.

WARNING: Never attempt to lock a switch in the

ONposition.

Fig. N

Setting The Chain Brake

Your chain saw is equipped with a motor chain braking

system which will stop the chain quickly in case ofkickback.

• Remove the battery from thetool.

• To engage the chain brake, push the chain brake / front

hand guard 3 forward until it clicks intoplace.

ENGLISH

• Pull the chain brake / front hand guard 3 towards the

front handle 13 into the “set” position as shown in

FigureO.

• The tool is now ready touse.

NOTE: In the event of kickback, your left hand will come in

contact with the front guard, pushing it forward, toward the

workpiece. This will stop thetool.

Fig. O

313

Testing The Chain Brake

Test the chain brake before every use to make sure it

operatescorrectly.

• Place the tool on a flat, firm surface. Make sure the saw

chain 5 is clear of theground.

• Grip the tool firmly with both hands and turn the chain

sawon.

• Rotate your left hand forward around the front handle

13 so the back of your hand comes in contact with

the Chain brake / front hand guard 3 and push it

forward, toward the workpiece. The saw chain should

stopimmediately.

NOTE: If saw does not stop immediately, stop use of tool

and bring it to a

DeWALT

service center nearestyou.

WARNING: Make sure to set chain brake

beforecutting.

Common Cutting Techniques

(Fig. A, P, Q, R, S, T)

Felling

The process of cutting down a tree. Be sure battery is fully

charged before felling a tree so you can finish on a single

charge. Do not fell trees in high windconditions.

WARNING: Felling can result in injury. It should only

be performed by a trainedperson.

• A retreat path should be planned and cleared as

necessary before cuts are started. The retreat path

should extend back and diagonally to the rear of the

expected line of fall (see FigureP).

DIRECTION

FALL

RETREAT

45° TREE

Fig. P

• Before felling is started, consider the natural lean of

the tree, the location of larger branches and the wind

direction to judge which way the tree will fall. Have

wedges (wood, plastic or aluminum) and a heavy mallet

handy. Remove dirt, stones, loose bark, nails, staples,

and wire from the tree where the felling cuts are to

bemade.

• Notching Undercut - Make the notch 1/3 of the

diameter of the tree, perpendicular to the direction of

the fall. Make the lower horizontal notching cut first.

This will help to avoid pinching of either the saw chain

or the guide bar when the second notch cut is being

made (see FigureQ).

• Felling Back Cut - Make the felling back cut at least 2"

(51mm) higher than the horizontal notching cut. Keep

the felling back cut parallel to the horizontal notching

cut. Make the felling back cut so enough wood is left

to act as a hinge. The hinge wood keeps the tree from

twisting and falling in the wrong direction. Do not cut

through the hinge (see FigureQ).

• As the felling cut gets close to the hinge the tree should

begin to fall. If there is any chance that the tree may

not fall in the desired direction or it may rock back and

bind the saw chain, stop cutting before the felling cut

is complete and use wedges to open the cut and drop

the tree along the desired line of fall. When the tree

begins to fall remove the chain saw from the cut, stop

the motor, put the chain saw down, then use the retreat

path planned. Be alert for overhead limbs falling and

watch yourfooting.

2" (51 mm)

DIRECTION OF FALL

2" (51 mm)

HINGE

NOTCH

FELLING BACK CUT

Fig. Q

Limbing

Removing the branches from a fallen tree. When limbing,

leave larger lower limbs to support the log off the ground.

Remove the small limbs in one cut. Branches under tension

should be cut from the bottom of the branch towards the

top to avoid binding the chain saw as shown in FigureR.

Trim limbs from opposite side keeping tree stem between

you and saw. Never make cuts with saw between your legs

or straddle the limb to becut.

ENGLISH

Fig. R

Bucking

WARNING: Recommend that first time users should

practice cutting on a sawhorse.

Cutting a felled tree or log into lengths. How you should cut

depends on how the log is supported. Use a saw horse (see

FigureS) wheneverpossible.

Fig. S

• Always start a cut with the chain running at fullspeed.

• Place the bottom spike 22 of the chain saw behind the

area of the initial cut as shown in FigureT.

• Turn the chain saw on then rotate the chain and bar

down into the tree, using the spike as ahinge.

• Once the chain saw gets to a 45 degree angle, level

the chain saw again and repeat steps until you cut

fullythrough.

• When the tree is supported along its entire length, make

a cut from the top (overbuck), but avoid cutting the

earth as this will dull your sawquickly.

CUT FROM TOP (OVERBUCK)

AVOID CUTTING EARTH

Fig. T

• FigureU- When supported at one end

First, cut 1/3 the diameter from the underside

(underbuck). Then make the finishing cut by

overbucking to meet the firstcut.

2nd CUT OVERBUCK

(2/3DIAMETER)

TO MEET 1st CUT

(TO AVOID PINCHING)

1st CUT UNDERBUCK

(1/3 DIAMETER)

AVOID SPLINTERING

Fig. U

• FigureV- When supported at bothends.

First, cut 1/3 down from the top overbuck. Then make

the finished cut by underbucking the lower 2/3 to meet

the firstcut.

2nd CUT UNDERBUCK

(2/3 DIAMETER)

TO MEET 1st CUT

(TO AVOID PINCHING)

1st CUT OVERBUCK

(1/3 DIAMETER)

TO AVOID SPLINTERING

Fig. V

• When on a slope always stand on the uphill side of the

log. When “cutting through”, to maintain complete

control reduce the cutting pressure near the end of the

cut without relaxing your grip on the chain saw handles.

Don’t let the chain contact the ground. After completing

the cut, wait for the saw chain to stop before you move

the chain saw. Always stop the motor before moving

from cut tocut.

CARE AND MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Do not

use solvents to clean the plastic housing of the saw. Never

let any liquid get inside the tool; never immerse any part of

the tool into aliquid.

IMPORTANT: To assure product SAFETY and RELIABILITY,

repairs, maintenance and adjustment should be performed

by a

DeWALT

authorized service center, always using

identical replacementparts.

Regular maintenance ensures a long effective life for your

chainsaw.

Chain and Bar

After every few hours of use, remove the sprocket cover,

guide bar and chain and clean thoroughly using a soft

bristle brush. Ensure oiling hole on bar is clear of debris.

When replacing dull chains with sharp chains it is good

practice to flip the chain bar from bottom totop.

Saw Chain Sharpening

CAUTION: Sharp chain. Always wear protective

gloves when handling the chain. The chain is sharp

and can cut you when it is notrunning.

ENGLISH

WARNING: Sharp moving chain. To prevent

accidental operation, ensure that battery is removed

from the tool before performing the following

operations. Failure to do this could result in serious

personalinjury.

NOTE: The cutters will dull immediately if they touch the

ground or a nail whilecutting.

To get the best possible performance from your chain saw

it is important to keep the teeth of the chain sharp. Follow

these helpful tips for proper saw chain sharpening:

1. For best results use a 4.5mm file and a file holder or

filing guide to sharpen your chain. This will ensure you

always get the correct sharpeningangles.

2. Place the file holder flat on the top plate and depth

gauge of thecutter.

3. FigureW- Keep the correct top plate 19 filing angle

line of 30° on your file guide parallel with your chain (file

at 60° from chain viewed from the side).

4. Sharpen cutters on one side of the chain first. File from

the inside of each cutter to the outside. Then turn your

saw around and repeat the processes (2, 3, 4) for cutters

on the other side of thechain.

NOTE: Use a flat file to file the tops of the rakers (portion

of chain link in front of the cutter) so they are about

.025" (.635 mm) below the tips of the cutters as shown

in FigureX.

5. FigureY- Keep all cutter lengthsequal.

6. If damage is present on the chrome surface of the

top plates or side plates, file back until such damage

isremoved.

CAUTION: After filing, the cutter will be sharp, use

extra caution during thisprocess.

NOTE: Each time the chain is sharpened, it loses some of

the low kickback qualities and extra caution should be used.

It is recommended that a chain be sharpened no more than

fourtimes.

60°

Fig. W

.025"

(0.635mm)

Fig. X

Fig. Y

Accessories

WARNING: The use of accessories not recommended

in this manual may behazardous.

Replacement chain and bar are available from your nearest

DeWALT

authorized service center. For use only with low

kick back bar andchain.

Available bars and chains for DCCS670:

Bar: 16” service part number N594320

18” service part number N594315

Chain: 16” service part number N594321

18” service part number N594318

MAINTENANCE

WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.

Cleaning

WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performingthis.

WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the plastic

materials used in these parts. Use a cloth dampened

only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool

into aliquid.

Accessories

WARNING: Since accessories, other than those

offered by

DeWALT

, have not been tested with this

product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only

DeWALT

recommended accessories should be used with

thisproduct.

Recommended accessories for use with your tool

are available at extra cost from your local dealer or

authorized service center. If you need assistance in

locating any accessory, please contact

DeWALT

Industrial

Tool Co., 701East Joppa Road, Towson, MD 21286, call

1-800-4-

DeWALT

(1-800-433-9258) or visit our website:

www.dewalt.com.

Repairs

The charger and battery pack are notserviceable.

ENGLISH

WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement, when

applicable) should be performed by a

DeWALT

factory

service center or a

DeWALT

authorized service center.

Always use identical replacementparts.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

Three Year Limited Warranty

DeWALT

will repair, without charge, any defects due to

faulty materials or workmanship for three years from the

date of purchase. This warranty does not cover part failure

due to normal wear or tool abuse. For further detail of

warranty coverage and warranty repair information, visit

www.dewalt.com or call 1-800-4-

DeWALT

(1-800-433-9258).

This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and

you may have other rights which vary in certain states

orprovinces.

In addition to the warranty,

DeWALT

tools are covered

byour:

1 YEAR FREE SERVICE

DeWALT

will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year

afterpurchase.

DEWALT BATTERY PACKS

Product warranty voided if the battery pack is tampered

with in any way. DeWalt is not responsible for any injury

caused by tampering andmay prosecute warranty fraud to

the fullest extent permitted bylaw.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of

your

DeWALT

Power Tool, Laser, or Nailer for any reason, you

can return it within 90 days from the date of purchase with

a receipt for a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-800-4-

DeWALT

(1-800-433-9258) for a freereplacement.

* Maximum initial battery voltage (measured without a

workload) is 20, 60 or 120 volts. Nominal voltage is 18, 54

or108. (120V Max* is based on using 2 D

WALT 60V Max*

lithium-ion batteries combined.)

FRANÇAIS

Définitions : symboles et termes d'alarmes sécurité

Ces guides d'utilisation utilisent les symboles et termes d'alarmes sécurité suivants pour vous prévenir de situations

dangereuses et de risques de dommages corporels ou matériels.

DANGER: indique une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort ou des

blessuresgraves.

AVERTISSEMENT: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner la

mort ou des blessuresgraves.

ATTENTION: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner des

blessures légères oumodérées.

(Si utilisé sans aucun terme) Indique un message propre à la sécurité.

AVIS : indique une pratique ne posant aucun risque de dommages corporels mais qui par contre, si rien n’est fait

pour l’éviter, pourrait poser des risques de dommages matériels.

AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

AVERTISSEMENT : afin de réduire le risque de

blessures, lire le mode d’emploi del’outil.

Pour toute question ou remarque au sujet de cet outil

ou de tout autre outil

DeWALT

, composez le numéro

sans frais : 1-800-4-

DeWALT

(1-800-433-9258).

Français (traduction de la notice d’instructions originale)

1 Gâchette à vitesse

variable

2 Levier de verrouillage

3 Frein de chaîne/Carter

de poignée avant

4 Guide-chaîne

5 Chaîne coupante

6 Cache de dent de

pignon

7 Bloc-piles

8 Bouton de verrouillage

du réglage de guide-

chaîne

9 Bouton de tension de

chaîne

10 Témoin de niveau d’huile

11 Fourreau du guide-

chaîne

12 Poignée arrière

13 Poignée avant

14 Logement du bloc-piles

15 Bouton de libération du

bloc-piles

16 Bouchon du réservoir

d’huile (non illustré)

FRANÇAIS

AVERTISSEMENTS DE SÉCURITÉ

GÉNÉRAUX POUR LES OUTILS

ÉLECTRIQUES

AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN USAGE

ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se

rapporte à votre outil électrique à alimentation sur secteur

(avec fil) ou par piles (sans fil).

1) Sécurité du lieu de travail

a ) Tenir l’aire de travail propre et bien éclairée.

Les lieux encombrés ou sombres sont propices

auxaccidents.

b ) Ne pas faire fonctionner d’outils électriques

dans un milieu déflagrant, tel qu’en présence de

liquides, de gaz ou de poussières inflammables.

Les outils électriques produisent des étincelles qui

pourraient enflammer la poussière ou lesvapeurs.

c ) Éloigner les enfants et les personnes à proximité

pendant l’utilisation d’un outil électrique. Une

distraction pourrait en faire perdre la maîtrise à

l’utilisateur.

2) Sécurité en matière d’électricité

a ) Les fiches des outils électriques doivent

correspondre à la prise. Ne jamais modifier la

fiche d’aucune façon. Ne jamais utiliser de fiche

d’adaptation avec un outil électrique mis à la

terre. Le risque de choc électrique sera réduit par

l’utilisation de fiches non modifiées correspondant à

laprise.

b ) Éviter tout contact physique avec des surfaces

mises à la terre comme des tuyaux, des

radiateurs, des cuisinières et des réfrigérateurs.

Le risque de choc électrique est plus élevé si votre corps

est mis à laterre.

c ) Ne pas exposer les outils électriques à la pluie ou

à l’humidité. La pénétration de l’eau dans un outil

électrique augmente le risque de chocélectrique.

d ) Ne pas utiliser le cordon de façon abusive.

Ne jamais utiliser le cordon pour transporter,

tirer ou débrancher un outil électrique. Tenir le

cordon éloigné de la chaleur, de l’huile, des bords

tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques

de chocélectrique.

e ) Pour l’utilisation d’un outil électrique à

l’extérieur, se servir d’une rallonge convenant à

cette application. L’utilisation d’une rallonge conçue

pour l’extérieur réduira les risques de chocélectrique.

f ) S’il est impossible d’éviter l’utilisation d’un

outil électrique dans un endroit humide,

brancher l’outil dans une prise ou sur un circuit

d’alimentation dotés d’un disjoncteur de fuite à

la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de chocélectrique.

3) Sécurité personnelle

a ) Être vigilant, surveiller le travail effectué et faire

preuve de jugement lorsqu’un outil électrique

est utilisé. Ne pas utiliser d’outil électrique en

cas de fatigue ou sous l’influence de drogues,

d’alcool ou de médicaments. Un simple moment

d’inattention en utilisant un outil électrique peut

entraîner des blessures corporellesgraves.

b ) Utiliser des équipements de protection

individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection

comme un masque antipoussière, des chaussures

antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert

réduira les risques de blessurescorporelles.

c ) Empêcher les démarrages intempestifs. S’assurer

que l’interrupteur se trouve à la position

d’arrêt avant de relier l’outil à une source

d’alimentation et/ou d’insérer un bloc-piles, de

ramasser ou de transporter l’outil. Transporter

un outil électrique alors que le doigt repose sur

l’interrupteur ou brancher un outil électrique dont

l’interrupteur est à la position de marche risque de

provoquer unaccident.

d ) Retirer toute clé de réglage ou clé avant de

démarrer l’outil. Une clé ou une clé de réglage

attachée à une partie pivotante de l’outil électrique

peut provoquer des blessurescorporelles.

e ) Ne pas trop tendre les bras. Conserver

son équilibre en tout temps. Cela permet

de mieux maîtriser l’outil électrique dans les

situationsimprévues.

f ) S’habiller de manière appropriée. Ne pas porter

de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à l’écart des

pièces mobiles. Les vêtements amples, les bijoux ou

les cheveux longs risquent de rester coincés dans les

piècesmobiles.

g ) Si des composants sont fournis pour le

raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux-ci sont bien

raccordés et utilisés. L’utilisation d’un dispositif de

dépoussiérage peut réduire les dangers engendrés par

lespoussières.

4) Utilisation et entretien d’un outil

électrique

a ) Ne pas forcer un outil électrique. Utiliser l’outil

électrique approprié à l’application. L’outil

électrique approprié effectuera un meilleur travail,

de façon plus sûre et à la vitesse pour laquelle il a

étéconçu.

La page charge ...

DeWalt DCCS670T1WS620B Manuel utilisateur

Marque: DeWalt

Modèle: DCCS670T1WS620B

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCCS670T1WS620B User manual
español: DeWalt DCCS670T1WS620B Manual de usuario

DeWalt DCCS670T1WS620B Manuel utilisateur

DeWalt DCCS670T1WS620B Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents