Tetra MAX 24V LED Signage Guide d'installation

Marque: Tetra

Modèle: MAX 24V LED Signage

Taper: Guide d'installation

MAX

LED Lighting System

Installation Guide

SIGN250 | DOC-2001497

Current Lighting Solutions, LLC

Beachwood, OH 44122

LED.com

of the General Electric Company and are used under license. Information provided is subject to change

without notice. All values are design or typical values when measured under laboratory conditions.

Page 1 of 6

Rev 08/28/23

SIGN250-Signage-Tetra-Max-Installation-UL-CE_R02

GEMX2471-W1S, GEMX2465-W1S, GEMX2457-W1S,

GEMX2450-W1S, GEMX2441-W1S, GEMX2432-W1S

RETROFIT SIGN CONVERSION LED KIT FOR USE ONLY IN

ACCORDANCE WITH KIT INSTRUCTIONS.

KIT IS COMPLETE ONLY WHEN ALL PARTS REQUIRED BY

THE INSTRUCTIONS ARE PRESENT.

TROUSSE DE CONVERSION À DEL POUR LA

MODERNISATION DES ENSEIGNES

À UTILISER CONFORMÉMENT AU GUIDE D’INSTALLATION.

Prepare Electrical Wiring

Electrical Requirements

• Acceptable for use in dry, damp and wet locations.

• The grounding and bonding of the LED Driver shall be

done in accordance with National Electric Code (NEC)

Article 600.

• Follow all National Electric Codes (NEC) and local codes.

• These products are only suitable for connection to a circuit from a

Class 2 power source.

• These products have not been evaluated for use when connected

to a power source that does not comply with Class 2 voltage and

energy limited supplies.

Save These Instructions

Use only in the manner intended by the

manufacturer. If you have any questions, contact the

manufacturer.

FOR UL ONLY

For the latest North American install guides for your product go to: https://products.LED.com/sign-lighting/tetra-max

For the latest European install guides for your product go to: https://products.LED.com/eu

BG Българската версия на инструкциите за инсталаця и

информация за безопасност могат да бъдат намерени

на следния адрес: https://products.LED.com/eu

CS Návod k montáží a bezpečnostní informace v češtině

najdete zde: https://products.LED.com/eu

DA Den danske version af installationsvejledningen og

sikkerhedsoplysninger kan ndes på følgende placering:

https://products.LED.com/eu

DE Die deutsche Version der Installationsanleitung und

Sicherheitsinformationen nden Sie in folgendem Verzeic:

https://products.LED.com/eu

EL Μπορείτε να βρείτε την ελληνική εκδχή των οδηγιών

νγκατάστασης και των πληροφοριών ασφάλειας στην

εξής τοποθεσία: https://products.LED.com/eu

ES La versión española de las instrucciones de instalación y

la información sobre seguridad puede encontrarse en la

siguiente ubicación: https://products.LED.com/eu

ET Eestikeelse paigaldusjuhendi ja ohutusnñuded leiate

aadressilt: https://products.LED.com/eu

FI Asennusohjeiden ja turvallisuustietojen suomenkielinen

versio löytyy seuraavasta paikasta: https://products.LED.

com/eu

FR La version française des instructions d’installations

et information de sécurité est disponible à l’adresse

suivante: https://products.LED.com/eu

HR Hrvatska verzija priručnika za ugradnju i sigurnosnih

informacija nalazi se na sljedečoj lokaciji: https://products.

LED.com/eu

HU A telepítési útmutató és a biztnosági információk magyar

nyelvű változata az alábbi címen található: https://

products.LED.com/eu

IT La versione italiana del manuale di installazione e

sicurezza può essere reperita nella seguente sezione:

https://products.LED.com/eu

LT Lietuvišką diegimo instrukcijos ir saugos informacijos

versiją galima rasti šioje vietoje: https://products.LED.

com/eu

LV Uzstādīšanas instrukciju un drošības informāciju latviešu

valodā var atrast šeit: https://products.LED.com/eu

NL De Nederlandse versie van de installatie-instructies en

veiligheidsinformatie kan op de volgende locatie worden

gevonden: https://products.LED.com/eu

PL Polską wersję instrukcji instalacji oraz informacje

dotyczące bezpieczeństwa można znaleźć w następującej

lokalizacji: https://products.LED.com/eu

PT A versão em Português das instruções de instalação e

das informações de segurança pode ser encontrada na

seguinte localização: https://products.LED.com/eu

RO Versiunea în limba română a instrucţiunilor de instalare

şi a informaţiilor de siguranţă pot  găsite la: https://

products.LED.com/eu

SV Ni hittar den svenska versionen av

installationsanvisningarna och säkerhetsinformationen på

följande plats: https://products.LED.com/eu

SL Previdnostna opozorila in varnostne informacije so na

zadnji strani vodnika za namestitev. Pred začetkom

namestitve izdelka jih skrbno preberite: https://products.

LED.com/eu

SK Slovenskú verziu montažnej príručky a bezpečnostnŷch

instrukcií nájdete na nasledujúcej lokalite: https://

products.LED.com/eu

BEFORE YOU BEGIN

Read these instructions completely and carefully.

2424

Volt

Tetra® MAX Installation Guide

Current Lighting Solutions, LLC

Beachwood, OH 44122

LED.com

of the General Electric Company and are used under license. Information provided is subject to change

without notice. All values are design or typical values when measured under laboratory conditions.

Page 2 of 6

Rev 08/28/23

SIGN250-Signage-Tetra-Max-Installation-UL-CE_R02

WARNING / AVERTISSEMENT

RISK OF ELECTRIC SHOCK

• Turn power o before inspection, installation or removal.

• Properly ground power supply enclosure.

RISK OF FIRE

• Use only suitably approved wire for input/output

connections. Minimum size 18 AWG (0.82mm2)

• Follow all local codes.

• Not to be submerged or used in a marine environment.

RISQUES DE DÉCHARGES ÉLECTRIQUES

• Coupez l’alimentation avant l’inspection, l’installation ou le déplacement.

• Assurez-vous de correctement mettre à terre l’alimentation électrique.

RISQUES D’INCENDIE

• N’utilisez que des ls approuvés par UL pour les entrées/sorties de connexion. Taille

minimum 18 AWG (0.82mm2)

• Respectez tous les codes locaux.

• Ne pas submerger ou installer dans un environnement marin.

UL WARNING / AVERTISSEMENT UL

RISK OF FIRE OR ELECTRIC SHOCK

• LED Retrot Kit installation requires knowledge of

sign electrical systems. If not qualied, do not attempt

installation. Contact a qualied electrician.

• Install this kit only in host signs that have been identied in

the installation instructions and where the input rating of

the retrot kit does not exceed the input rating of the sign.

• Installation of this LED retrot kit may involve drilling or

punching of holes into the structure of the sign. Check

for enclosed wiring and components to avoid damage to

wiring and electrical parts.

• Do not make or alter any open holes in an enclosure of

wiring or electrical components during kit installation.

RISQUE D’INCENDIE OU DE CHOC ÉLECTRIQUE

• L’installation de l’équipement de remplacement DEL exige Ia connaissance des

systèmes électriques pour enseignes. Si non qualié, ne tentez pas d’installation.

Veuillez contacter un électricien qualié.

• Risque d’incendie ou de choc électrique. Installez cet ensemble seulement dans des

enseignes hôtes qui ont été identiés dans les instructions d’installation et dont la

capacité d’entrée de l’ensemble ne dépasse pas la capacité d’entrée de l’enseigne.

• L’installation de cet équipement de remplacement DEL peut impliquer le perçage ou le

poinçonnage de trous dans la structure du panneau Vériez le câblage et les composants

inclus pour éviter d’endommager le câblage et les composants électriques.

• Ne pas faire ou modier les trous ouverts dans une enceinte de câblage ou de

composants électriques pendant l’installation de cet équipement de remplacement DEL.

UL approved 18 AWG (0.82 mm2) supply wire

UL approved 22-14 AWG (0.33-2.08 mm2) wire connectors or

22-18 AWG (0.33-0.82 mm2) in-line/IDC connectors

#6 (M3) screws, 1/8 inch (3.2 mm) rivets, or electrical grade RTV

silicone or equivalent

Weather box GEXNWB2 (optional)

24 Volt Power Supply

Tetra® MAX LED modules

Electrical grade RTV silicone:

• Momentive RTV 6700 Series Silicone Rubber Adhesive Sealant

• Momentive White Blanc RTV 162 Silicone Rubber Adhesive

Sealant-Electrical Grade

• Dow Corning 3140 - Non-Corrosive Flowable (clear)

• Dow Corning 3145 - Non-Corrosive Nonowable (clear or gray)

• Dow Corning RTV 748 Non-Corrosive Sealant-White

Components

TC Measure Point

1234

Tetra® MAX Installation Guide

Current Lighting Solutions, LLC

Beachwood, OH 44122

LED.com

of the General Electric Company and are used under license. Information provided is subject to change

without notice. All values are design or typical values when measured under laboratory conditions.

Page 3 of 6

Rev 08/28/23

SIGN250-Signage-Tetra-Max-Installation-UL-CE_R02

Components - Tetra® SNAP Accessories (optional)

Tetra SNAP Rail (GEDSRL08-3)

Tetra Snap SS Metal Clip (GESSMC-3)

Tetra SNAP Frame Endcap (GEDSFE-3)

Tetra SNAP Socket Endcap (GEDSSE-3)

Tetra SNAP Dual Rail Socket Cap (GESSDR-3)

Tetra SNAP T-connector (GEDSTC-3)

Tetra SNAP Interconnector (GEDSIC-3)

Tetra MAX is also compatible with the following Tetra SNAP Rail components.

See https://products.LED.com/led-signage-lighting for further details and install instructions.

Measure and cut Tetra LED strip

to the appropriate length for

each letter. Cuts can be made

between any of the modules.

Remove tape backing and stick LED

modules into place. When using

tape apply approximately 15 psi

pressure on the module (avoid the

lens dome surface) for 5 seconds,

full bonding strength after 24 hours.

Continue until you have reached the

end of the strip.

Use rivets, screws, or electrical

grade RTV silicone to secure

at least every fth LED module

within the channel letter. Use #6

(M3) pan headed metal screws,

1/8-inch (3.2 mm) rivets, or

electrical grade RTV silicone.

Before you begin, clean surfaces

and remove all debris from the

inside of the channel letter. Clean

the surfaces with a 50:50 mixture

of isopropyl alcohol (IPA) and

water and let dry.

Layout Modules

Drill a 1/4-inch (6.4 mm) hole

near the LED strip and grommet

the hole for supply wire access.

Remove all the debris from the

inside of the channel letter and

replace the sign face.

NOTE: For halo-lit applications LED modules should be mounted on UL

recognized clear acrylic or polycarbonate. The light output from the LED

system should be directed back into the sign enclosure. This will allow for

uniform backlighting of the sign and will provide simple mounting.

Do not

press lens

Tetra® MAX Installation Guide

Current Lighting Solutions, LLC

Beachwood, OH 44122

LED.com

of the General Electric Company and are used under license. Information provided is subject to change

without notice. All values are design or typical values when measured under laboratory conditions.

Page 4 of 6

Rev 08/28/23

SIGN250-Signage-Tetra-Max-Installation-UL-CE_R02

Connect LED strips using in-line (IDC) connectors or

twist-on wire connectors.

NOTE: Seal all connections in wet locations with

electrical grade RTV silicone.

Must cap all exposed wires with appropriate wire

connectors and seal with electrical grade RTV silicone.

Optional: Cut wires ush to the module and seal with

electrical grade RTV silicone.

Electrical Connections

NOTE: Do not use connectors pre-lled with silicone grease/mineral base protective grease or use silicone grease to seal connections.

Red stripe (+)

White (-)

Cap wires Optional: Cut wires ush

Seal all connections in wet locations

with electrical grade RTV silicone

1 2

To LED

power

supply

Red (+)

Black or

blue (-)

Red Stripe (+)

Run a wire from the LED power supply to the LED

module and connect.

NOTE: Must be used with Class 2 24 Volt Power

Supplies.

NOTE: Refer to Maximum Loading & Remote

Mounting Specications on page 4.

Connect the red stripe wire (+) of the LED strip to the

red wire (+) of the power supply. Connect the white

wire (-) of the LED strip to the black or blue wire (-) of

the LED power supply.

NOTE: All electrical connections should be suitably

protected from mechanical damage and the

environment. Seal all connections in wet locations

with electrical grade RTV silicone.

LED

Power

Supply

To Tetra LED System

Red (+)

Black or blue (-)

White (-)

Seal all connections in wet locations

with electrical grade RTV silicone

OPTIONAL

A Weather Box (GEXNWB2) may be used to

house and seal Class 2 connections.

A) Insert wire connectors into weather box. Fill

with electrical grade silicone and close box.

B) Secure the weather box using a #6 or #8

(M2 or M3) screw.

Weather box

can be painted

Tetra® MAX Installation Guide

Current Lighting Solutions, LLC

Beachwood, OH 44122

LED.com

of the General Electric Company and are used under license. Information provided is subject to change

without notice. All values are design or typical values when measured under laboratory conditions.

Page 5 of 6

Rev 08/28/23

SIGN250-Signage-Tetra-Max-Installation-UL-CE_R02

Retrot Instructions

1. (Existing Signs Only) Prior to installation, survey the site for information regarding power and accessibility inside and outside the

building. Ensure that the branch circuit supplying the existing transformer or ballast will be within the voltage ratings of the new LED

power supply, and have a current rating not exceeding 20A, or that permitted by applicable local, state, or country electrical codes

(whichever is less).

2. (Existing Signs Only) Remove the existing lighting equipment to be replaced, such as neon tubing or uorescent tubes; and

associated transformers and ballasts. Care should be taken not to break the existing neon or uorescent tubes. NOTE: Follow all

federal and local regulations when disposing of neon tubing, uorescent tubes, transformers and ballasts.

3. (Existing Signs Only) If removal of the existing lighting equipment eliminates the disconnect switch, as required by applicable

local, state, or country electrical codes; a new disconnect switch must be installed.

4. (Existing Signs Only) Repair and seal any unused openings in the electrical enclosure. Openings greater than 12.7-mm (1/2-in)

diameter require a metal patch secured by screws or rivets and caulked with non-hardening caulk. Smaller openings may be sealed

with non-hardening caulk.

5. (Existing Signs Only) A clean and dry mounting surface ensures optimum adhesion if the self-adhesive method of mounting is

chosen. Follow the manufacturer’s directions when using a non-oil based solvent, such as rubbing alcohol to clean the surface area

where you intend to mount the module. Before installing, ensure the surface is dry.

6. Using the layout guidelines above, determine required number of LED modules required to illuminate the sign.

7. A 24VDC Class 2 Power Supply, as listed below, must be used with this retrot kit. Using the Maximum Loading chart below,

determine the number of Power Supplies required to power the number of LED modules required to illuminate the sign, so as not to

overload the Power Supply chosen.

8. Follow the instructions above to properly mount the LED modules.

9. Connect the DC output of the power supply to the LED modules using the Electrical Connections instructions above.

10. Connect the power unit to the supply in accordance with the applicable local, state, and country electrical codes, and the instructions

found in the power supply installation guide.

11. If required, the disconnect switch shall be installed by qualied personnel, in accordance with applicable local, state, and country

electrical codes.

FOR UL ONLY

• For optimal light uniformity in halo-lit applications the Tetra® LED modules should be mounted on UL recognized plastic and the light

output from the Tetra® LED system should be directed back into the sign enclosure. This will allow for uniform backlighting of the sign

and will provide simple mounting for the Tetra® LED system.

• A best practice for the supply wire at the point at which it is brought into the sign is to have a drip loop on the inside of the letter to

keep water from collecting on the Tetra® LED strip.

Tips

Symptom Solution

All letters are OFF • Check AC input connection and/or check circuit breaker.

• Check wire connection(s) at the Tetra® LED System and power supply for improper termination(s) or short

circuits. Properly terminate or replace the wire connection(s).

• Check that connections are the red striped wire (+) of the LED strip to the red wire (+) of the power supply

and the white wire (-) of the LED strip to the black or blue wire (-) of the power supply.

Some LEDs

appear dim

• Ensure the overall length of the Tetra® LED System does not exceed the maximum load.

• Ensure the length of supply wire is equal to or below the recommended remote mounting distance.

• Ensure the overall length of the Tetra® LED System does not exceed the maximum load.

Some of the letters are

not illuminated

• Check wire connection(s) at the Tetra® LED System and power supply for improper termination(s) or short

circuits. Properly terminate or replace the wire connection(s).

• Check that connections are the red striped wire (+) of the LED strip to the red wire (+) of the power

supply and the white wire (-) of the LED strip to the black or blue wire (-) of the power supply.

Shadows • Re-route supply wire and secure to the back of the can with electrical grade RTV silicone. Adjust wire

connector orientation so that it does not cover any LEDs.

• Adjust LED layout to ensure uniformity of illumination on the face of the letter.

Troubleshooting

Dismantling

At the end of life, the contained LED light source may be cut out using suitable wire cutters, removed from the mounting surface,

then replaced per the cutting and installation instructions above, or dismantled and taken to a communal collecting point for

environmentally friendly disposal in accordance with local regulations by a professional installer.

Tetra® MAX Installation Guide

Any changes or modications not expressly

approved by the party responsible for

compliance could void the user’s authority to

operate this equipment.

NOTE: The maximum loading claimed in the table is at ambient temperature 25°C (77°F).

For linear long runs, center connection to the LED strip is recommended to minimize voltage drop.

*GELP24-60U-GL minimum load = 33 modules / 22 ft. (6.70 m).

**GEPS24V50-100W minimum load = 81 modules / 54 ft. (16.46 m).

Maximum Loading per 24V DC Power Supply

Power Supply

GEMX2471-W1S, GEMX2465-W1S, GEMX2457-W1S

GEMX2450-W1S, GEMX2441-W1S, GEMX2432-W1S

Rating per module 24V DC, 26mA/module, 0.62W/module

GEPS24-25U-NA

Load shall not exceed 1.04A 33 modules/22 ft. (6.7 m)

GEPS24D-60U-GLX, *GELP24-60U-GL

Load shall not exceed 2.5A 88 modules/58 ft. (17.88 m)

GEPS24D-80U, GEPS24W-80

Load shall not exceed 3.3A 110 modules/73 ft. (22.3 m)

GEPS24-100U-GLX, GEPS24D-100U-NA, GEPS24LT-100U-NA,

USVI-100024FBA, USVI-100024FE

Load shall not exceed 4.0A

130 modules/87 ft. (26.4 m)

GEPS24-180U

Load shall not exceed 3.8A per each (of 2) output channels

120 modules/80 ft. (24.4 m) per bank

240 modules/160 ft. (48.8 m) per PS

GEPS24-300U-GL

Load shall not exceed 4.0A per each (of 3) output channels

130 modules/87 ft. (26.4 m) per bank

390 modules/260 ft. (79.3 m) per PS

GEPS24-100U-GLX2/TT, **GEPS24V50-100W

Load shall not exceed 4.0A 139 modules/92.6 ft. (28.2 m)

GEPS24-200U-GLX2

Load shall not exceed 4.0A per each (of 2) output channels

139 modules/92.6 ft. (28.2 m) per bank

278 modules/185 ft. (56.3 m) per PS

GEPS24-300U-GLX2

Load shall not exceed 4.0A per each (of 3) output channels

139 modules/92.6 ft. (28.2 m) per bank

417 modules/278 ft. (84.7 m) per PS

This product is intended solely for sign use only. Not intended for general lighting applications.

Conforms to the following standards: IP66 rated

III

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

This Class [A] RFLD complies with the Canadian standard ICES-005. Ce DEFR de la classe [A] est conforme à la NMB-005 du Canada.

Electrical products must not be thrown out with domestic waste. They must be taken to a communal collecting point for environmentally friendly

disposal in accordance with local regulations. Contact your local authorities or stockist for advice on recycling. The packaging material is recyclable.

Dispose of the packaging in an environmentally friendly manner and make it available for the recyclable material collection-service.

Power Supply

Wattage

18 AWG/0.82 mm2

Supply Wire

16 AWG/1.31 mm2

Supply Wire

14 AWG/2.08 mm2

Supply Wire

12 AWG/3.31 mm2

Supply Wire

25W 120 ft./36.6 m – – –