VTech CS5249-2 Guide de démarrage rapide

Marque: VTech

Modèle: CS5249-2

Catégorie: Téléphones

Taper: Guide de démarrage rapide

Ce manuel convient également à

CS5249

What’s in the box

Speciﬁcations are subject to change without notice.

Technical speciﬁcations

Frequency

control Crystal controlled PLL synthesizer

Transmit

frequency Handset: 1921.536-1928.448 MHz

Telephone base: 1921.536-1928.448 MHz

Channels DECT channel: 5

Nominal

effective

range

Maximum power allowed by FCC and IC.

Actual operating range may vary according to

environmental conditions at the time of use.

Power

requirement Handset: 2.4V Ni-MH battery

Telephone base: 6V DC @ 400mA

Charger: 6V DC @ 400mA

Memory Phonebook: 50 memory locations;

up to 30 digits and 15 characters

Caller ID log: 30 memory locations;

up to 24 digits and 15 characters

Call block: 150 entries

Connect and activate

Basic operation

Go to www.vtechphones.com

to register your product for enhanced

warranty support and latest VTech

product news.

Quick start guide

CS5249

CS5249-2

CS5249-3

CS5249-4

CS5249-5

After you install your telephone or power returns following a power outage and battery depletion, the handset and

telephone base will prompt you to set the date and time, and to conﬁgure the answering system through voice guide.

Date and time

Follow the steps below to set the date and time. For example, if the date is 25 December, 2019, and the time is 10:59 AM:

Voice guide for answering system

After setting the date and time, the handset and telephone base will display Voice guide to... and set up Ans sys?

alternatively.

This feature assists you to do the basic setup of the answering system. You can follow the voice guide to record your own

announcement, set the number of rings and the message alert tone.

Setup your answering system by inputting

the designated numbers as instructed in the

voice guide.

Date: 12/25/19

ECO

Voice guide

to... “Hello! This voice guide

will assist you with the

basic setup of your

answering system“

When the handset

and telephone base

prompt you to set

the date and time

When the handset

prompts you to set up

the answering system

via voice guide

Setup

Caller ID

If you subscribe to caller ID service, information about

each caller appears after the ﬁrst or second ring.

The caller ID log stores up to 30 entries. Each entry

has up to 24 digits for the phone number and 15

characters for the name.

Review caller ID log entries

Handset

ECO ANS ON

10:15pm 12/25

Mike Smith

595-9511

ECO

NEW

ANS ON

09:05pm 12/25

Caller ID

Edit number

595-9511_

ECO

Edit number

800-595-9511_

ECO

>To Phonebook

ECO

Edit name

Mike Smiths_

ECO

Save a caller ID log entry to the phonebook

Delete a caller ID log entry

Mike Smith

595-9511

ECO

NEW

ANS ON

09:05pm 12/25

When your

desired caller ID

entry displays on

the handset or

telephone base

screen

When your desired caller ID entry displays on the handset or

telephone base screen

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1939

Quick

start

guide

Make a call

Handset: Telephone base:

Volume

Answer a call

- OR -

End a call

Handset: Need help?

For operations and guides to help you using your telephone, and for latest information and supports, go and check the online help topics and online FAQs.

Use your smartphone or mobile device to access our online help.

• Go to https://help.vtechphones.com/cs5249; OR

• Scan the QR code on the right. Launch the camera app or QR code scanner app on your smartphone or tablet. Hold the device’s camera

up to the QR code and frame it. Tap the notiﬁcation to trigger the redirection of the online help.

- If the QR code is not clearly displayed, adjust your camera’s focus by moving your device closer or further away until it is clear.

You can also call our Customer Support at 1 (800) 595-9511 [in US] or 1 (800) 267-7377 [in Canada] for help.

Dial a caller ID log entry

Mike Smith

595-9511

ECO

NEW

ANS ON

09:05pm 12/25

When your desired caller ID entry displays on the handset or

telephone base screen

- OR -

Telephones identiﬁed with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and

cochlear implants. The TIA-1083 Compliant Logo is a trademark of

the Telecommunications Industry Association. Used under license.

Compatible with

Hearing Ai

d T-Coil

TIA-1083

The ENERGY STAR® program (www.energystar.gov) recognizes and

encourages the use of products that save energy and help protect our

environment. We are proud to mark this product with the ENERGY

STAR® label indicating it meets the latest energy efﬁciency guidelines.

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage

or loss resulting from the use of this user’s manual. VTech Communications, Inc. and its

suppliers assume no responsibility for any loss or claims by third parties that may arise

through the use of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States

Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada

Handset:

Telephone base:

- OR - Lift the corded

handset

Handset: Telephone base:

Date: MM/DD/YY

ECO

Date: 12/2?/YY

ECO

Time: 1?:MM --

ECO

Time: 10:59 AM

ECO

Telephone base:

Mike Smith

595-9511

ECO

NEW

ANS ON

09:05pm 12/25

Press

Handset:

Lift the corded handset

Telephone base:

- OR -

Place the handset on

the telephone base

- OR -

DECT 6.0 cordless telephone

Enter the date.

Press SELECT.

Enter the time.

Press SELECT.

Press MENU.

Press SELECT

to select To

phonebook.

Edit the phone

number

if needed.

Press SELECT .

Edit the name

if needed, then

press SELECT.

Press SELECT.

Enter the

phone number

Press

- OR -

Handset:

Press any dialing

keys to answer

Press Telephone base:

Lift the corded handset

- OR -

Press

Press .

Press / to

browse the entries.

LCD language setting

If you accidentally set the LCD language

to Spanish or French, press MENU and

then enter 364# to change the handset

LCD language back to English while the

handset is not in use.

Press

Connect the telephone base

If you subscribe to digital subscriber line (DSL) high-

speed Internet service through your telephone line,

make sure you connect a DSL ﬁlter (not included) to

the telephone wall jack.

Install the battery

Connect the charger

Charge the battery

12 hrs

Display

Handset: Telephone base:

Telephone base ringer is off.

New voicemail received

from your telephone service

provider.

NEW

New caller ID log entries.

MSG#

5/10 Number of new/old

messages recorded.

The battery is low and

needs charging.

The battery is charging.

The battery is fully charged.

Handset ringer is off.

New voicemail received

from your telephone

service provider.

NEW

There are new caller ID log

entries.

ANS ON Answering system is on.

MSG#

5/10 Number of new/old

messages recorded.

ECO The ECO mode activates

automatically to reduce

power consumption when

the handset is within range

of the telephone base.

12:05 pm 7/25

HANDSET

Base

10:15

12/25

NEW

MSG#

HANDSET

ECO

NEW

ANS ON

10:15

MSG#

5/10

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 400mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1535

THIS SIDE UP

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V 400mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1535

See Mount the telephone base (optional) online for the

wall mounting instructions.

Tip

Important safety instructions

When using your telephone equipment, basic safety precautions should always be followed

to reduce the risk of ﬁre, electric shock and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol

cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink,

laundry tub or a swimming pool, nor in a wet basement or shower.

5. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

6. Avoid placing the telephone system in places with extreme temperature, direct sunlight,

or other electrical devices. Protect your phone from moisture, dust, corrosive liquids and

fumes.

7. Slots and openings in the back or bottom of the telephone base and handset are provided

for ventilation. To protect them from overheating, these openings must not be blocked by

placing the product on a soft surface such as a bed, sofa or rug. This product should never

be placed near or over a radiator or heat register. This product should not be placed in any

area where proper ventilation is not provided.

8. This product should be operated only from the type of power source indicated on the

marking label. If you are not sure of the type of power supply in your home or ofﬁce,

consult your dealer or local power company.

9. Do not allow anything to rest on the power cord. Do not install this product where the cord

may be walked on.

10. Never push objects of any kind into this product through the slots in the telephone base or

handset because they may touch dangerous voltage points or create a short circuit. Never

spill liquid of any kind on the product.

11. To reduce the risk of electric shock, do not disassemble this product, but take it to an

authorized service facility. Opening or removing parts of the telephone base or handset

other than speciﬁed access doors may expose you to dangerous voltages or other risks.

Incorrect reassembling can cause electric shock when the product is subsequently used.

12. Do not overload wall outlets and extension cords.

13. Unplug this product from the wall outlet and refer servicing to an authorized service facility

under the following conditions:

• When the power supply cord or plug is damaged or frayed.

• If liquid has been spilled onto the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally by following the operating instructions.

Adjust only those controls that are covered by the operation instructions. Improper

adjustment of other controls may result in damage and often requires extensive work

by an authorized technician to restore the product to normal operation.

• If the product has been dropped and the telephone base and/or handset has been

damaged.

• If the product exhibits a distinct change in performance.

14. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote

risk of electric shock from lightning.

15. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain

circumstances, a spark may be created when the adapter is plugged into the power

outlet, or when the handset is replaced in its cradle. This is a common event associated

with the closing of any electrical circuit. The user should not plug the phone into a power

outlet, and should not put a charged handset into the cradle, if the phone is located in

an environment containing concentrations of ﬂammable or ﬂame-supporting gases,

unless there is adequate ventilation. A spark in such an environment could create a ﬁre or

explosion. Such environments might include: medical use of oxygen without adequate

ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a leak of natural gas;

etc.

16. Only put the handset of your telephone next to your ear when it is in normal talk mode.

17. The power adapter is intended to be correctly oriented in a vertical or ﬂoor mount

position. The prongs are not designed to hold the plug in place if it is plugged into a

ceiling, under-the-table or cabinet outlet.

18. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall

be easily accessible.

19. CAUTION: Use only the batteries indicated in this manual. There may be a risk

of explosion if a wrong type of battery is used for the handset. Use only the supplied

rechargeable batteries or replacement batteries (BT162342/BT262342) for the handset.

Do not dispose of batteries in a ﬁre. They may explode.

20. Use only the adapter included with this product. Incorrect adapter polarity or voltage can

seriously damage the product.

SAVE THESE INSTRUCTIONS

Battery

• CAUTION: Use Only Supplied Battery.

• Do not dispose of the battery in a ﬁre. Check with local waste management codes for

special disposal instructions.

• Do not open or mutilate the battery. Released electrolyte is corrosive and may cause

burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.

• Exercise care in handling batteries in order not to create a short circuit with conductive

materials.

• Charge the battery provided with this product only in accordance with the instructions

and limitations speciﬁed in this manual.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless telephones):

Wireless Technology Research, LLC (WTR), an independent research entity, led a

multidisciplinary evaluation of the interference between portable wireless telephones and

implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR

recommends to physicians that:

Pacemaker patients

• Should keep wireless telephones at least six inches from the pacemaker.

• Should NOT place wireless telephones directly over the pacemaker, such as in a breast

pocket, when it is turned ON.

• Should use the wireless telephone at the ear opposite the pacemaker.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons

using wireless telephones.

About cordless telephones

• Privacy: The same features that make a cordless telephone convenient create some

limitations. Telephone calls are transmitted between the telephone base and the cordless

handset by radio waves, so there is a possibility that the cordless telephone conversations

could be intercepted by radio receiving equipment within range of the cordless handset.

For this reason, you should not think of cordless telephone conversations as being as

private as those on corded telephones.

• Electrical power: The telephone base of this cordless telephone must be connected to a

working electrical outlet. The electrical outlet should not be controlled by a wall switch.

Calls cannot be made from the cordless handset if the telephone base is unplugged,

switched off or if the electrical power is interrupted.

• Potential TV interference: Some cordless telephones operate at frequencies that may

cause interference to televisions and VCRs. To minimize or prevent such interference, do

not place the telephone base of the cordless telephone near or on top of a TV or VCR. If

interference is experienced, moving the cordless telephone farther away from the TV or

VCR often reduces or eliminates the interference.

• Rechargeable batteries: Exercise care in handling batteries in order not to create a

short circuit with conducting material such as rings, bracelets and keys. The battery or

conductor may overheat and cause harm. Observe proper polarity between the battery

and the battery charger.

• Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe

manner. Do not burn or puncture the battery. Like other batteries of this type, if burned

or punctured, they could release caustic material which could cause injury.

For more support information

Handset

ECO ANS ON

10:15pm 12/25

Follow the following steps to set the date

and time if you skipped the prompt.

Set date/time

ECO

Press / to

scroll to Set date/time,

then press SELECT.

Press MENU.

Date: 12/25/19

ECO

Enter the date, then

press SELECT.

3Enter the time, then

press SELECT.

Time: 10:59 AM

ECO

About the built-in answering system and voicemail service

For message recording, your telephone has a built-in answering system, and it also supports voicemail service offered by your

telephone service provider (subscription is required, and fee may apply).

Built-in answering system VS Voicemail service

Built-in answering system Voicemail service

Supported by Telephone system Telephone service provider

Subscription No Yes

Fees No May apply

Answer incoming calls

• After 3 rings by default.

• It can be changed via handset or the

telephone base menu.

• Usually after 2 rings.

• It can be changed by contacting your telephone service provider.

Storage Telephone base Server or System

Display new messages • Handset - XX new messages

• Telephone base - Message window ﬂashes

• Handset - and New voicemail

• Telephone base -

Retrieve messages

• Press on the telephone base; OR

• Press MENU, and then select Play messages

on the handset; OR

• Access remotely with an access code.

• Press on the dialpad, and enter an access number and/or

passcode from your telephone service provider.

Answering system

Call Block

Turn the built-in answering system on or off

On the telephone base

Press to turn on;

press again to turn off. For C-UL compliance only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de blessures corporelles ou d’électrocution, suivez

toujours ces mesures préventives de base lorsque vous utilisez votre téléphone :

1. Lisez et comprenez bien toutes les instructions.

2. Observez toutes les instructions et mises en garde inscrites sur l’appareil.

3. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas de

nettoyeurs liquides ni en aérosol. N’utilisez qu’un chiffon doux et légèrement humecté.

4. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier

de cuisine, d’un bac de lavage ou d’une piscine, ou dans un sous-sol humide ou sous la

douche.

5. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil

pourrait tomber et être sérieusement endommagé.

6. Évitez d’installer le système téléphonique dans les endroits soumis à une température

extrême, à la lumière directe du soleil ou à proximité immédiate d’autres appareils

électriques ou électroniques. Protégez votre téléphone contre les sources d’humidité, la

poussière, les vapeurs et les liquides corrosifs.

7. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière ou

en dessous. Aﬁn d’empêcher la surchauffe, ces ouvertures ne doivent pas être obstruées

en plaçant l’appareil sur un lit, divan, tapis ou autre surface similaires. Ne placez pas cet

appareil à proximité d’un élément de chauffage ni d’une plinthe électrique. De plus, ne

l’installez pas dans une unité murale ou un cabinet fermé qui ne possède pas d’aération

adéquate.

8. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les étiquettes

de l’appareil. Si vous ne connaissez pas le voltage de votre maison, consultez votre

marchand ou votre fournisseur d’électricité.

9. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit

sécuritaire, là où personne ne pourra trébucher sur la ligne d’alimentation ni le cordon

téléphonique modulaire.

10. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils pourraient

toucher à des points de tension dangereux ou court-circuiter des pièces, ce qui

constituerait un risque d’incendie ou d’électrocution. N’échappez pas de liquides dans

l’appareil.

11. Aﬁn de réduire les risques d’électrocution, ne démontez pas l’appareil, mais apportez-le

plutôt à un centre de service qualiﬁé s’il doit être réparé. En enlevant le couvercle, vous

vous exposez à des tensions dangereuses ou autres dangers similaires. Un remontage

inadéquat peut être à l’origine d’une électrocution lors d’une utilisation ultérieure de

l’appareil. Débranchez l’appareil avant de procéder au nettoyage. Utilisez un chiffon

humide et doux.

12. Ne surchargez pas les prises de courant et les rallonges.

13. Débranchez cet appareil de la prise de courant et communiquez avec le département de

service à la clientèle de VTech dans les cas suivants :

• Lorsque le cordon d’alimentation est endommagé ou écorché.

• Si du liquide a été échappé dans l’appareil.

• Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.

• Si le produit ne fonctionne pas normalement en respectant les instructions de

fonctionnement. Réglez uniquement les commandes indiquées dans le les instructions

de fonctionnement. Les réglages incorrects des autres commandes pourraient

provoquer un dommage qui pourrait exiger un travail exhaustif de la part d’un

technicien autorisé aﬁn de rétablir le fonctionnement normal de l’appareil.

• Si le produit a été échappé et que le socle et/ou le combiné a été endommagé.

• Si le produit afﬁche une nette diminution de sa performance.

14. Évitez d’utiliser un téléphone (autre qu’un sans ﬁl) pendant un orage. Les éclairs peuvent

être à l’origine d’une électrocution.

15. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite. En

certaines circonstances, une ﬂammèche pourrait être provoquée lorsque l’adaptateur

est branché à une prise de courant, ou lorsque le combiné est déposé sur le socle. Ceci

est un événement commun associé à la fermeture d’un circuit électrique. L’utilisateur

ne devrait pas brancher le téléphone à une prise de courant, et ne devrait pas déposer

le combiné chargé sur le socle, si le téléphone se trouve à proximité d’un endroit

comportant des concentrations de gaz inﬂammables, à moins que la ventilation soit

adéquate. Une ﬂammèche dans un tel endroit pourrait provoquer un incendie ou une

explosion. De tels environnements peuvent comprendre: des endroits où l’on utilise

de l’oxygène médical sans ventilation adéquate; des gaz industriels (dissolvants de

nettoyage, des vapeurs d’essence, etc.); une fuite de gaz naturel, etc.

16. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode de

conversation.

17. Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au sol.

Les broches ne sont pas conçues pour maintenir l’adaptateur en place si celui-ci est barnché

dans une prise au plafond ou sous une table/ armoire.

18. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le socle de prise de courant doit

etre installe a proximite du materiel et doit etre aisement accessible.

19. MISE EN GARDE: Il peut y avoir un risque d’explosion si vous utilisez le

mauvais type de piles pour le téléphone. N’utilisez que les piles rechargeable inclus

ou les piles de rechange (BT162342/BT262342). N’incinérez pas les piles. Celles-ci

risqueraient d’exploser.

20. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur

dont la polarité ou la tension serait inadéquate risque d’endommager sérieusement

le produit et mettre votre sécurité en péril.

CONSERVEZ CES INSTRUCTIONS

Pile

• N’utilisez que la pile incluse ou l’équivalent.

• Ne jetez pas la pile au feu. Vériﬁez les instructions spéciﬁques de mise aux rebus auprès

des autorités locales.

• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif et

pourrait causer des brûlures ou des blessures aux yeux ou à la peau. L’électrolyte est

toxique si avalé.

• Soyez prudents lorsque vous manipulez les piles aﬁn d’éviter les courts-circuits provoqués

par des matériaux conducteurs.

• Rechargez la pile incluse avec cet appareil, selon les instructions et limites spéciﬁées dans

ce guide d’utilisation.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans ﬁl) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une ﬁrme de recherche

indépendante, a mené une évaluation pluridisciplinaire des interférences entre les

téléphones sans ﬁl portatifs et les stimulateurs cardiaques implantés dans l’organisme.

Appuyée par l’Administration des aliments et drogues (FDA) des États-Unis, la ﬁrme WTR

recommande aux médecins :

Avis aux détenteurs de stimulateurs cardiaques

• Ils doivent tenir le téléphone sans ﬁl à une distance d’au moins six pouces du stimulateur

cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement sur le stimulateur cardiaque, tel

que dans une poche de chemise, lorsque celui-ci est en marche.

• Ils doivent utiliser le téléphone sans ﬁl en l’appuyant sur l’oreille qui se trouve dans la

direction opposée au stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de risque pour les détenteurs de

simulateurs cardiaques causés par les gens qui utilisent un téléphone sans ﬁl à proximité de

ceux-ci.

À propos des téléphones sans ﬁl

Conﬁdentialité : Les mêmes caractéristiques qui constituent des avantages pour les

téléphones sans ﬁl afﬁchent également des restrictions. Les appels téléphoniques sont

transmis entre le combiné sans ﬁl et le socle par le biais d’ondes radio ; il y a donc la possibilité

que vos conversations téléphoniques sans ﬁl soient interceptées par des équipements

de réception radio se trouvant dans la portée du combiné sans ﬁl. Pour cette raison, vous

ne devez pas percevoir les communications téléphoniques sans ﬁl comme étant aussi

conﬁdentielles que celles des téléphones à cordons.

Alimentation électrique : Le socle de ce téléphone sans ﬁl doit être branché à une prise

électrique fonctionnelle. La prise électrique ne doit pas être contrôlée par un interrupteur

mural. Les appels ne pourront pas être effectués du combiné sans ﬁl si le socle est débranché

ou mis hors tension ou si le courant est coupé.

Possibilité d’interférences aux téléviseurs : Certains téléphones sans ﬁl fonctionnent sur des

fréquences pouvant causer des interférences aux téléviseurs et aux magnétoscopes. Pour

réduire ou prévenir de telles interférences, ne placez pas le socle du téléphone sans ﬁl près

ou sur un téléviseur ou magnétoscope. S’il y a présence de parasites, il est conseillé d’éloigner

le téléphone sans ﬁl du téléviseur ou du magnétoscope aﬁn de réduire possiblement les

interférences.

Piles rechargeables : Manipulez les piles avec soin aﬁn de ne pas les court-circuiter avec des

bagues, bracelets ou clés. Les piles ou le conducteur peut surchauffer et causer des blessures.

Respectez la polarité adéquate entre la pile et le chargeur.

Les bloc-piles rechargeables à l’hydrure métallique de nickel : Jetez ces blocs-piles de

manière écologique et sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les autres

piles de ce type, elles pourraient dégager une matière toxique qui peut causer des blessures

corporelles si elles sont brûlées ou percées.

The RBRC® seal

The RBRC® seal on the nickel-metal hydride battery indicates that VTech

Communications, Inc. is voluntarily participating in an industry program to collect

and recycle these batteries at the end of their useful lives, when taken out of

service within the United States and Canada.

The RBRC® program provides a convenient alternative to placing used nickel-

metal hydride batteries into the trash or municipal waste, which may be illegal in

your area.

VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers

participating in the RBRC® program or at authorized VTech product service centers. Please call

1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/restrictions

in your area. VTech’s involvement in this program is part of its commitment to protecting our

environment and conserving natural resources.

RBRC® and 1 (800) 8 BATTERY® are registered trademarks of Rechargeable Battery Recycling

Corporation.

FCC, ACTA and IC regulations

FCC Part 15

NOTE: This equipment has been tested and found to comply with the requirements for

a Class B digital device under Part 15 of the Federal Communications Commission (FCC)

rules. These requirements are intended to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Privacy of communications may not be ensured when using this telephone.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency

energy that can be safely absorbed by a user or bystander according to the intended usage

of the product. This product has been tested and found to comply with the FCC criteria. The

handset may be safely held against the ear of the user. The telephone base shall be installed

and used such that parts of the user’s body other than the hands are maintained at a distance

of approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical requirements

adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the

back or bottom of this equipment contains, among other things, a product identiﬁer in the

format US:AAAEQ##TXXXX. This identiﬁer must be provided to your telephone service

provider upon request.

The plug and jack used to connect this equipment to premises wiring and the telephone

network must comply with applicable Part 68 rules and technical requirements adopted

by ACTA. A compliant telephone cord and modular plug is provided with this product. It is

designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack

should normally be used for connecting to a single line and an RJ14 jack for two lines. See the

installation instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to determine how many devices you may

connect to your telephone line and still have them ring when you are called. The REN for this

product is encoded as the 6th and 7th characters following the US: in the product identiﬁer

(e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be ﬁve

(5.0) or less. For more information, please contact your telephone service provider.

This equipment must not be used with Party Lines. If you have specially wired alarm dialing

equipment connected to your telephone line, ensure the connection of this equipment

does not disable your alarm equipment. If you have questions about what will disable alarm

equipment, consult your telephone service provider or a qualiﬁed installer.

If this equipment is malfunctioning, it must be unplugged from the modular jack until the

problem has been corrected. Repairs to this telephone equipment can only be made by the

manufacturer or its authorized agents. For repair procedures, follow the instructions outlined

under the Limited warranty.

If this equipment is causing harm to the telephone network, the telephone service provider

may temporarily discontinue your telephone service. The telephone service provider is

required to notify you before interrupting service. If advance notice is not practical, you will

be notiﬁed as soon as possible. You will be given the opportunity to correct the problem

and the telephone service provider is required to inform you of your right to ﬁle a complaint

with the FCC. Your telephone service provider may make changes in its facilities, equipment,

operation, or procedures that could affect the proper functioning of this product. The

telephone service provider is required to notify you if such changes are planned.

If this product is equipped with a corded or cordless handset, it is hearing aid compatible.

If this product has memory dialing locations, you may choose to store emergency telephone

numbers (e.g., police, ﬁre, medical) in these locations. If you do store or test emergency

numbers, please:

Remain on the line and brieﬂy explain the reason for the call before hanging up.

Perform such activities in off-peak hours, such as early morning or late evening.

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,

Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to

the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired

operation of the device.

Privacy of communications may not be ensured when using this telephone.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the Industry

Canada technical speciﬁcations were met.

The Ringer Equivalence Number (REN) for this terminal equipment is 1.0. The REN indicates

the maximum number of devices allowed to be connected to a telephone interface. The

termination of an interface may consist of any combination of devices subject only to the

requirement that the sum of the RENs of all the devices not exceed ﬁve.

This product meets the applicable Innovation, Science and Economic Development Canada

technical speciﬁcations.

California Energy Commission battery

charging testing instructions

This telephone is set up to comply with the energy-conserving standards right out of the box.

These instructions are intended for California Energy Commission (CEC) compliance testing only.

When the CEC battery charging testing mode is activated, all telephone functions, except battery

charging, will be disabled.

To activate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power outlet. Make sure all handsets

are plugged with charged batteries before proceeding.

2. While you press and hold /FIND HANDSET, plug the telephone base power adapter back

to the power outlet.

3. After about 10 seconds, when the IN USE light starts ﬂashing and the telephone base shows

Registering... and then De-register?, release /FIND HANDSET and immediately press it

within two seconds.

When the phone successfully enters the CEC battery charging testing mode, all handsets

display To register HS... and ...see manual alternately.

When the phone fails to enter this mode, repeat steps 1 to 3 above.

To deactivate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power outlet, and then plug it back in.

Then the telephone base is powered up as normal.

2. Press and hold /FIND HANDSET on the telephone base for about four seconds until the

IN USE light turns on and the handset shows Registering....

3. Press QUIET# on the handset. The handset shows Registered, and you hear a beep when

the registration process completes. This process takes about 60 seconds.

Limited Warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase

(“Consumer” or “you”) that the Product and all accessories provided in the sales package

(“Product”) are free from defects in material and workmanship, pursuant to the following terms

and conditions, when installed and used normally and in accordance with the Product operating

instructions. This limited warranty extends only to the Consumer for Products purchased and

used in the United States of America and Canada.

What will VTech do if the Product is not free from defects in materials and workmanship

during the limited warranty period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service representative will repair or replace

at VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may

use new or refurbished replacement parts. If we choose to replace the Product, we may replace

it with a new or refurbished Product of the same or similar design. We will retain defective parts,

modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive

remedy. VTech will return the repaired or replacement Products to you in working condition. You

should expect the repair or replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase.

If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty,

this limited warranty also applies to the repaired or replacement Product for a period of either

(a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time

remaining on the original one-year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage,

improper installation, abnormal operation or handling, neglect, inundation, ﬁre, water or

other liquid intrusion.

2. Product that has been subjected to contact with liquid, water, rain, extreme humidity

or heavy perspiration, sand, dirt or the like; but then only to the extent the damage was

not caused by incorrectly securing the waterproof handset’s protective elements, for

example, failing to properly close a seal), or such protective elements are damaged or

missing (e.g. a cracked battery door), or subjecting a Product to conditions beyond its

stated speciﬁcations or limits (e.g. 30 minutes in 1 meter of fresh water).

3. Product that has been damaged due to repair, alteration or modiﬁcation by anyone

other than an authorized service representative of VTech;

4. Product to the extent that the problem experienced is caused by signal conditions,

network reliability, or cable or antenna systems;

5. Product to the extent that the problem is caused by use with non-VTech accessories;

6. Product whose warranty/quality stickers, product serial number plates or electronic serial

numbers have been removed, altered or rendered illegible;

7. Product purchased, used, serviced, or shipped for repair from outside the United States

of America or Canada, or used for commercial or institutional purposes (including but

not limited to Products used for rental purposes);

8. Product returned without a valid proof of purchase (see item 2 below); or

9. Charges for installation or set up, adjustment of customer controls, and installation or repair

of systems outside the unit.

How do you get warranty service?

To obtain warranty service in the United States of America, please visit our website at

www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or dial 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls

and features may save you a service call.

Except as provided by applicable law, you assume the risk of loss or damage during transit and

transportation and are responsible for delivery or handling charges incurred in the transport of

the Product(s) to the service location. VTech will return repaired or replaced Product under this

limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no

risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited

warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify

you and will request that you authorize the cost of repair prior to any further repair activity. You

must pay for the cost of repair and return shipping costs for the repair of Products that are not

covered by this limited warranty.

What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech

service location along with a description of the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased

(Product model) and the date of purchase or receipt; and

3. Provide your name, complete and correct mailing address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement between you and VTech. It supersedes all

other written or oral communications related to this Product. VTech provides no other warranties

for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the

Product. There are no other express warranties. No one is authorized to make modiﬁcations to

this limited warranty and you should not rely on any such modiﬁcation.

State/Provincial Law Rights: This warranty gives you speciﬁc legal rights, and you may also

have other rights, which vary from state to state or province to province.

Limitations: Implied warranties, including those of ﬁtness for a particular purpose and

merchantability (an unwritten warranty that the Product is ﬁt for ordinary use) are limited to one year

from the date of purchase. Some states/provinces do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for

any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost

proﬁts or revenue, inability to use the Product or other associated equipment, the cost of substitute

equipment, and claims by third parties) resulting from the use of this Product. Some states/

provinces do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof of purchase

Set number of rings

You can set your answering system to answer calls at least two rings earlier than your voicemail service. For example, if your

voicemail service answers after six rings, set your answering system to answer after four rings. Thus, if you are on a call, or if the

answering system is busy recording a message and you receive another call, the second caller can leave a voicemail message.

Delete all messages

Using the telephone base

Play the previous message

Call Block

If you subscribe to caller ID service, you can set the telephone

to block unknown calls and certain undesired calls. The call

block list can store up to 150 entries.

Add a call block entry

Handset

ECO

10:15pm 12/25

Call block

ECO

q Block list

ECO

Add new entry

ECO

Enter number

800-595-9511_

ECO

Enter name

Mike Smiths_

ECO

Delete a call block list entry

When the desired call

block list entry displays

on the handset screen

Mike Smith

595-9511

ECO

09:05pm 12/25

Block unknown calls

Handset

ECO

10:15pm 12/25

Call block

ECO

q Calls w/o num

ECO

Block

ECO

Review a call block list entry

Handset

ECO

10:15pm 12/25

Call block

ECO

q Block list

ECO

Review

ECO

Press / to scroll

to Call block, then

press SELECT.

Press SELECT

to select Block list.

4Press / to scroll

to Add new entry,

then press SELECT.

Press MENU.

Enter number

then press SELECT.

Enter name

then press SELECT.

1Press MENU.2Press / to scroll

to Call block,

then press SELECT.

3Press / to scroll

to Call w/o num,

then press SELECT.

Press MENU.

12Press / to scroll

to Call block,

then press SELECT.

Press SELECT

to select Block list.

Press SELECT

to select Review.

Press / to scroll

to Block, then

press SELECT..

Press DELETE

to delete.

1Press MENU. 2Press / to scroll

to Answering sys,

then press SELECT.

Press / to scroll

to Ans sys setup,

then press SELECT.

4Press / to scroll

to # of rings,

then press SELECT.

Press / to scroll to

the desired number of

rings, then press SELECT.

Handset

ECO ANS ON

10:15pm 12/25

>Answering sys

ECO

>Ans sys setup

ECO

># of rings

ECO

Skip a message

Repeat the playing message

- OR -

Press

- OR -

Press

Message playback

On the telephone base

On a handset

Press MENU.

Press SELECT

to select Play messages.

>Play messages

ECO

Handset

ECO ANS ON

10:15pm 12/25

- OR -

Press

- OR -

Press

Phonebook

The phonebook can store up to 50 entries, which are shared

by all handsets and the telephone base. Each entry may

consist of a telephone number up to 30 digits, and a name up

to 15 characters.

Add a phonebook entry

Handset

ECO ANS ON

10:15pm 12/25

595-9511_

ECO

Enter name

ECO

Mike Smith

ECO

Review phonebook entries

Delete a phonebook entry

Mike Smith

800-595-9511

ECO

Delete entry ?

ECO

Handset

ECO ANS ON

10:15pm 12/25

Mike Smith

800-595-9511

ECO

Phonebook

>Enter number

595-9511

ECO

When your desired phonebook entry displays on the

handset screen

Enter the phone

number. 2

Press MENU.

Press SELECT.

Enter the name.

Press SELECT.

Press .

Press / to

browse the entries.

Press DELETE.

Press SELECT.

VTech CS5249-2 Guide de démarrage rapide

Marque: VTech

Modèle: CS5249-2

Catégorie: Téléphones

Taper: Guide de démarrage rapide

Ce manuel convient également à

CS5249

Télécharger le PDF

rapport

dans d''autres langues

English: VTech CS5249-2 Quick start guide

VTech CS5249-2 Guide de démarrage rapide

Ce manuel convient également à

VTech CS5249-2 Guide de démarrage rapide

dans d''autres langues

Documents connexes